3-868-272-11 (1)
Video Cassette
Recorder
Operating Instructions
PAL NTSC4.43
SLV-SE700G
SLV-SE700I
SLV-SE800G
SLV-SE800I
© 2000 Sony Corporation
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified service shop.
Notice for customers in the United Kingdom and Republic of Ireland
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
If the 13A fitted plug does not match the outlet socket in your home, please refer to your Appointed Sony Dealer for advice.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI
to BS1362, (i.e., marked with or mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
Precautions
Safety
•This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.
•If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
•The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
•Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
Installing
•Allow adequate air circulation to prevent internal heat buildup.
•Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
•Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
•Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
•Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
•Do not place heavy objects on the unit.
•If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.
Caution
Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record using the PAL colour system and play back using the PAL and NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed.
VIDEO Plus+ and PlulsCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.
2 WARNING
Table of contents
Getting Started
4Step 1 : Unpacking
5Step 2 : Setting up the remote commander
9Step 3 : Connecting the VCR
13Step 4 : Setting up the VCR with the Auto Set Up function
14Step 5 : Tuning your TV to the VCR
17 Selecting a language
19 Presetting channels
23 Changing/disabling programme positions
29 Setting the clock
34 Setting your personal code
Basic Operations
36 Playing a tape
39 Recording TV programmes
43Recording TV programmes using the Dial Timer
(SLV-SE800G and SE800I only)
48Recording TV programmes using the VIDEO Plus+ system
52 Setting the timer manually
Additional Operations
55 Playing/searching at various speeds
58Setting the recording duration time
59Synchronized Recording (SLV-SE800G and SE800I only)
62Checking/changing/cancelling timer settings
64Recording stereo and bilingual programmes
66Searching using the Smart Search function
69Searching using the index function
70Adjusting the picture
72 Changing menu options
Editing
74Connecting to a VCR or stereo system
76Basic editing
77Audio dubbing
(SLV-SE800G and SE800I only)
Additional Information
79 Troubleshooting
83Specifications
84Index to parts and controls
Back Cover
Index
Started Getting
Table of contents 3
Check that you have received the following items with the VCR:
• Remote commander • Aerial cable
• R6 (size AA) batteries
The instructions in this manual are for the 4 models: SE700G, SE700I, SE800G and SE800I. Check your model number by looking at the rear panel of your VCR. SLV-SE800G is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE700I only.”
4 Unpacking
Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV.
Remote sensor
[TV] / [VIDEO]
Started Getting
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
|
0 |
|
To operate |
Set [TV] / [VIDEO] to |
|
|||
|
|
|
|
||
the VCR |
[VIDEO] and point at the remote sensor at the VCR |
|
|
|
|
|
|
|
|
||
a Sony TV |
[TV] and point at the remote sensor at the TV |
|
|
|
|
|
|
|
|
||
|
|
continued |
|||
|
Setting up the remote commander |
|
5 |
||
|
|
||||
|
|
|
|
|
|
WIDE
AUDIO MONITOR
FASTEXT buttons
DISPLAY
1 2 3
4 5 6
7 8 9
- 0
TV control buttons
?/1
/
a
t TV/VIDEO
Programme number buttons
PROG +/–/ c/C
2 +/–
|
|
|
To |
Press |
|
|
|
|
|
|
|
|
Set the TV to standby mode |
?/1 |
|
|
|
|
|
|
|
|
Select an input source: aerial in or line in |
t TV/VIDEO |
|
|
|
|
|
|
|
|
Select the TV’s programme position |
Programme number buttons, -, |
|
|
|
|
PROG +/– |
|
|
|
||
6 |
|
Setting up the remote commander |
|
|
|
|
|||
|
|
|
|
|
To |
Press |
|
|
Adjust the volume of the TV |
2+/– |
|
|
Switch to TV (Teletext off) |
a (TV) |
|
|
Switch to Teletext |
/ (Teletext) |
|
|
Select the sound |
AUDIO MONITOR |
|
|
Use FASTEXT |
FASTEXT buttons |
|
|
Call up the on-screen display |
DISPLAY |
|
|
Change the Teletext page |
c/C |
|
|
Switch to/from wide mode of a Sony wide TV (For other |
WIDE |
manufactures’ wide TVs, see “Controlling other TVs with |
|
the remote commander.”) |
|
|
|
Notes
•With normal use, the batteries should last about three to six months.
•If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
•Do not use a new battery together with an old one.
•Do not use different types of batteries together.
•Some buttons may not work with certain Sony TVs.
The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number.
1 Set [TV] / [VIDEO] at the top of the remote commander to [TV].
2 Hold down ?/1, and enter your TV’s code number using the programme number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, -(ten’s digit), PROG +/–, 2+/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*, M/m/</ ,*, and OK*.
Started Getting
* These buttons may not work with all TVs.
continued
Setting up the remote commander 7
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable code numbers.
Manufacturer |
Code number |
|
|
Sony |
01*1, 02 |
|
|
Akai |
68 |
|
|
Ferguson |
52 |
|
|
Grundig |
10*1, 11*1 |
|
|
Hitachi |
24 |
|
|
JVC |
33 |
|
|
Loewe |
45 |
|
|
Mivar |
09, 70 |
|
|
NEC |
66 |
|
|
Nokia |
15, 16, 69*3 |
|
|
Manufacturer |
Code number |
|
|
Panasonic |
17*1, 49 |
|
|
Philips |
06*1, 07*1, 08*1 |
|
|
Saba |
12, 13 |
|
|
Samsung |
22, 23 |
|
|
Sanyo |
25 |
|
|
Sharp |
29 |
|
|
Telefunken |
36 |
|
|
Thomson |
43*2 |
|
|
Toshiba |
38 |
|
|
*1 Press WIDE to switch the wide picture mode on or off.
*2 Press WIDE, then press 2+/– to select the wide picture mode you want.
*3 Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to select the wide picture you want and press OK.
Tip
•When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.
Notes
•If you enter a new code number, the code number previously entered will be erased.
•If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander.
•When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.
8 Setting up the remote commander
If your TV has a Scart (EURO-AV) connector, see page 10.
Mains lead
to mains
AERIAL IN |
AERIAL OUT
AERIAL IN
Aerial cable (supplied)
: Signal flow
Started Getting
1
2
3
Disconnect the aerial cable from your |
AERIAL |
TV and connect it to AERIAL IN on |
ANTENNE |
IN |
|
the rear panel of the VCR. |
ENTREE |
|
|
|
OUT |
|
SORTIE |
Connect AERIAL OUT of the VCR |
AERIAL |
and the aerial input of your TV using |
ANTENNE |
IN |
|
the supplied aerial cable. |
ENTREE |
|
|
|
OUT |
|
SORTIE |
Connect the mains lead to the mains.
Note
•When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 14).
continued
Connecting the VCR 9
|
AERIAL IN |
i LINE-1 |
AERIAL OUT |
Mains lead |
(TV) |
|
|
to mains |
AERIAL IN |
|
|
|
Aerial cable (supplied) |
|
Scart |
: Signal flow |
(EURO-AV) |
|
|
|
Scart cable (not supplied) |
1
2
3
4
Disconnect the aerial cable from your |
AERIAL |
TV and connect it to AERIAL IN on |
ANTENNE |
IN |
|
the rear panel of the VCR. |
ENTREE |
|
|
|
OUT |
|
SORTIE |
Connect AERIAL OUT of the VCR |
AERIAL |
and the aerial input of your TV using |
ANTENNE |
IN |
|
the supplied aerial cable. |
ENTREE |
|
|
|
OUT |
|
SORTIE |
Connect LINE-1 (TV) on the VCR and the Scart (EURO-AV) connector on the TV with the optional Scart cable.
This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press t TV/ VIDEO to display the VIDEO indicator in the display window.
Connect the mains lead to the mains.
If the mains plug does not fit in the mains, use the supplied plug adaptor.
Note
•If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 16).
10 Connecting the VCR
If the connected TV complies with |
SMARTLINK |
SMARTLINK, MEGALOGIC*1, EASYLINK*2, Q-Link*3, EURO VIEW LINK*4, or T-V LINK*5, this VCR automatically runs the SMARTLINK
function after you complete the steps on the previous page (the SMARTLINK indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.
•Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful not to disconnect the cables or exit the Auto Set Up function during the procedure.
See “Setting up the VCR with the Auto Set Up function” on page 13.
•TV Direct Rec
You can easily record what you are watching on the TV. For details, see “Recording what you are watching on the TV (TV Direct Rec)” on page 42.
•One Touch Play
With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play)” on page 38.
•One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander.
•One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the timer recording menu (the TIMER METHOD menu, the TIMER menu, or the
VIDEO Plus+ menu) automatically by pressing TIMER on the remote commander.
You can set which timer recording menu is displayed using TIMER OPTIONS in the OPTIONS-2 menu (see page 73).
•Automatic Power Off
You can have the VCR turn off automatically, if the VCR is not used after you turn off the TV.
Started Getting
*1 “MEGALOGIC” is a registered trademark of Grundig Corporation. *2 “EASYLINK” is a trademark of Philips Corporation.
*3 “Q-Link” is a trademark of Panasonic Corporation.
*4 “EURO VIEW LINK” is a trademark of Toshiba Corporation.
*5 “T-V LINK” is a trademark of JVC Corporation.
Note
• Not all TVs respond to the functions above.
continued
Connecting the VCR 11
To a stereo system
You can improve sound quality by connecting a stereo system to the AUDIO OUT R/L jacks as shown on the right.
AUDIO OUT |
LINE IN |
|
R/L |
||
|
Audio cable (not supplied)
: Signal flow
To a set top box with Line Through
Using the Line Through function, you can watch programmes from a set top box connected to this VCR on the TV even when the VCR is turned off. When you turn on the set top box, this VCR automatically sends the signal from the set top box to the TV without turning itself on.
t LINE-3 IN*1
LINE OUT
or t LINE-2 IN*2
Scart cable (not supplied)
: Signal flow
1 Connectabove. the set top box to the LINE-3 IN*1 (or LINE-2 IN*2) connector as shown 2 Set POWER SAVE to OFF in the OPTIONS-2 menu.
3 Turn off the VCR.
To watch a programme, turn on the set top box and the TV.
Note
•You cannot watch programmes on the TV while recording unless you are recording a programme from your set top box.
*1 SLV-SE800G and SE800I only *2 SLV-SE700G and SE700I only
12 Connecting the VCR
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the TV channels, guide channels for the VIDEO Plus+ system, and VCR clock automatically.
AUTO SET UP
AUTO Hold down AUTO SET UP on the VCR for more than three seconds.
SET UP
The VCR automatically turns on and starts searching for all of the receivable channels and presets them in the appropriate order for your local
RF CHANNEL area.
If you want to change the order of the channels or disable unwanted programme positions, see “Changing/disabling programme positions” on page 23.
If you use the SMARTLINK connection, the Preset Download function starts and the SMARTLINK indicator flashes in the display window during download.
After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal. If the time does not appear, set the clock manually (see page 29).
To cancel the Auto Set Up function
Press AUTO SET UP.
Notes
•Do not cancel the Auto Set Up function. If you do, repeat the step above.
•Whenever you operate the Auto Set Up function, some of the settings (VIDEO Plus+, timer, etc.) will be reset. If this happens, you have to set them again.
Started Getting
Setting up the VCR with the Auto Set Up function 13
If your TV has a Scart (EURO-AV) connector, see page 16.
Follow the steps below so that your TV will properly receive the video signals from your VCR.
RF CHANNEL
PROGRAM +/–
1 |
AUTO |
SET UP |
RF CHANNEL
Press RF CHANNEL on the VCR lightly.
The currently set RF channel appears in the display window.
The VCR signal is output through this channel to the TV.
2
3
Turn on your TV and select a programme position for the VCR picture.
This programme position will now be referred to as the video channel.
Tune the TV to the same channel shown in the VCR display window so that the
picture on the right appears clearly on the SONY VIDEO CASSETTE RECORDER TV screen.
Refer to your TV manual for TV tuning instructions.
If the picture does not appear clearly, see “To obtain a clear picture from the VCR.” below.
14 Tuning your TV to the VCR
4 |
AUTO |
Press RF CHANNEL. |
SET UP |
|
You have now tuned your TV to the VCR. Whenever you want to play a tape, set the TV to the video channel.
RF CHANNEL
To check to see if the TV tuning is correct
Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.
To obtain a clear picture from the VCR
If the screen does not appear clearly in step 3 above, press PROGRAM +/– so that another RF channel appears. Then tune the TV to the new RF channel so that a clear picture appears.
continued
Started Getting
Tuning your TV to the VCR 15
RF CHANNEL
PROGRAM +/–
1 |
AUTO |
SET UP |
RF CHANNEL
Press RF CHANNEL on the VCR lightly.
The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.
2 PROGRAM
TRACKING
AUTO
SET UP
Press PROGRAM +/– to set the RF channel to OFF, and press RF CHANNEL again.
RF channel set up is complete.
RF CHANNEL
16 Tuning your TV to the VCR
If you prefer an on-screen language other
than English, use the on-screen display to |
0 |
|
|
select another language. |
|
Before you start… |
|
• Turn on the VCR and the TV. |
|
• Set the TV to the video channel. |
|
MENU
M/m/</,
OK
Started Getting
1
2
Press MENU, then press M/m to highlight
MENU |
SETTINGS and press OK. |
|
PLAY
OK
SETTINGS |
|
|
TUNER |
|
|
CLOCK |
|
|
LANGUAGE |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
Press M/m to highlight LANGUAGE, then |
|
|
|
press OK. |
LANGUAGE |
|
|
PLAY |
ENGLISH |
NEDERLANDS |
|
|
|
||
|
DEUTSCH |
DANSK / NORSK |
|
OK |
FRANÇ AIS |
SVENSKA |
|
|
ITALIANO |
SUOMI |
|
|
ESPAÑ OL |
|
|
|
PORTUGUÊ S |
|
|
SELECT : |
|
|
|
SET |
: OK |
EXIT |
: MENU |
|
|
continued
Selecting a language 17
3 |
Press M/m/</, to highlight the desired language, then press OK. |
|
|
|
PLAY |
|
OK |
4 |
Press MENU to exit the menu. |
MENU |
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
• The menu disappears automatically if you don’t proceed for more than a few minutes.
18 Selecting a language
If some channels could not be preset using the Auto Set Up function, you can preset them manually.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
1 |
2 |
3 |
|
4 |
5 |
6 |
Programme |
7 |
8 |
9 |
number |
buttons |
|||
|
0 |
|
|
|
|
|
PROG +/– |
|
|
|
MENU |
|
|
|
|
M/m/</, |
|
|
|
|
OK |
1 |
MENU |
Press MENU, then press M/m to highlight |
|
|
SETTINGS and press OK. |
SETTINGS |
|||
|
|
|
TUNER |
|
|
|
|
CLOCK |
|
|
|
|
LANGUAGE |
|
|
|
|
RETURN |
|
|
PLAY |
|
|
|
|
|
|
SELECT |
: |
|
OK |
|
SET |
: OK |
|
|
|
|
EXIT : MENU |
Started Getting
continued
Presetting channels 19
2 |
Press M/m to highlight TUNER, then press |
ex. SLV-SE800I |
|
|
|
|
OK. |
|
TUNER |
|
|
|
|
PLAY |
|
|
PROG. |
1 |
||
|
|
|
||||
OK |
|
NORMAL / CATV |
NORMAL |
|
||
|
CHANNEL SET |
C1 2 |
AAB |
|
||
|
|
AFT |
|
ON |
|
|
|
|
FINE TUNING |
|
|
|
|
|
|
RETURN |
|
|
|
|
|
|
SELECT : |
|
|
|
|
|
|
SET |
: OK |
EXIT |
: MENU |
|
|
|
|
|
3
PLAY
OK
SLV-SE700I and SE800I only:
Press M/m to highlight NORMAL/CATV, then press OK.
TUNER |
PROG. |
1 |
||
|
|
|||
NORMAL / CATV |
NORMAL |
|
|
|
CHANNEL SET |
CATV |
|
|
|
AFT |
|
|
|
|
FINE TUNING |
|
|
|
|
RETURN |
|
|
|
|
SELECT |
: |
|
|
|
CONFIRM |
: OK |
EXIT |
: MENU |
|
|
|
4
PLAY
OK
SLV-SE700I and SE800I only:
Press M/m to highlight NORMAL, then press OK.
To preset CATV (Cable Television) channels, select CATV.
TUNER |
|
PROG. |
1 |
|
|
||
NORMAL / CATV |
NORMAL |
|
|
CHANNEL SET |
C1 2 |
AAB |
|
AFT |
ON |
|
|
FINE TUNING |
|
|
|
RETURN |
|
|
|
SELECT :
SET : OK
EXIT : MENU
5
6
•PROG Press PROG +/– to select the programme
position.
Selected programme
position |
|
|
|
TUNER |
|
PROG. |
4 |
|
|
||
NORMAL / CATV |
NORMAL |
|
|
CHANNEL SET |
C1 2 |
AAB |
|
AFT |
ON |
|
|
FINE TUNING |
|
|
|
RETURN |
|
|
|
SELECT :
SET : OK
EXIT : MENU
Press M/m to highlight CHANNEL SET, |
|
|
|
|
then press OK. |
TUNER |
PROG. |
4 |
|
|
|
|
|
|
PLAY |
NORMAL / CATV |
|
|
|
|
C1 2 |
AAB |
|
|
|
CHANNEL SET |
|
||
OK |
AFT |
|
|
|
|
FINE TUNING |
|
|
|
|
RETURN |
|
|
|
|
SELECT : |
|
|
|
|
CONFIRM : OK |
EXIT |
: MENU |
|
|
|
20 Presetting channels
7
PLAY
OK
1 2 3
4 5 6
7 8 9
0
Press M/m repeatedly until the channel you want is displayed.
The channels appear in the following
order: |
|
|
|
|
|
|
|
|
|
|
TUNER |
PROG. 4 |
|
||
|
|
|
|
|
|||
• VHF IA - IJ, SA10 - SA13 (SLV-SE700I |
|
|
NORMAL / CATV |
|
|
|
|
|
|
CHANNEL SET |
C2 7 |
|
|
||
|
|
AFT |
|
|
|
||
and SE800I only) |
|
|
|
|
|
||
|
|
FINE TUNING |
|
|
|
||
|
|
RETURN |
|
|
|
||
• UHF B21 - B69 |
|
|
|
|
|
|
|
• CATV S1 - S20 (SLV-SE700I and |
|
|
|
|
|
|
|
SELECT : |
|
|
|
||||
SE800I only) |
|
CONFIRM : OK |
EXIT : MENU |
|
|||
|
|
|
|
|
•HYPER S21 - S41 (SLV-SE700I and SE800I only)
•CATV S01 - S05 (SLV-SE700I and SE800I only)
If you know the number of the channel you want, press the programme number buttons. For example, for channel 5, first press “0” and then press “5.”
8 |
To preset another programme position, repeat steps 5 through 7. |
|
Started Getting
9 |
Press MENU to exit the menu. |
MENU |
|
|
|
continued
Presetting channels 21
Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. However, if the picture is not clear, you may also use the manual tuning function.
1
2 Press MENU, then select SETTINGS and press OK.
3 Select TUNER, then press OK.
4 Select FINE TUNING, then press OK. The fine tuning meter appears.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TUNER |
|
PROG. 4 |
|
|
|||
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
||||
|
|
NORMAL / CATV |
|
|
|
|
||||
|
|
NORMAL |
|
|
|
|||||
|
|
CHANNEL SET |
C2 7 |
|
|
|
||||
|
|
AFT |
|
|
|
|
|
|
|
|
|
|
FINE TUNING |
|
|
|
|
|
|
|
|
|
|
RETURN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SET : |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
EXIT : |
MENU |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
Selected programme position
5 Press </, to get a clearer picture, then press MENU to exit the menu. Note that the AFT (Auto Fine Tuning) setting switches to OFF.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Notes
•The menu disappears automatically if you don’t proceed for more than a few minutes.
•When adjusting FINE TUNING, the menu may become difficult to read due to interference from the picture being received.
22 Presetting channels
After setting the channels, you can change
the programme positions as you like. If any |
0 |
|
|
programme positions are unused or contain |
|
unwanted channels, you can disable them. |
|
You can also change the station names. If the |
|
station names are not displayed, you can |
MENU |
enter them manually. |
|
Before you start…
M/m/,
OK
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Started Getting
1
2
Press MENU, then press M/m to highlight
MENU |
LISTS and press OK. |
|
PLAY
OK
LISTS |
|
|
CHANNEL LIST |
|
|
TIMER LIST |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
|
Press M/m to highlight CHANNEL LIST, |
|
|
|
|
|
|
|
|
|
|
|
|
then press OK. |
|
|
|
|
|
|
|
|
|
|
|
|
|
CHANNEL LIST |
|
|
|
|||||||
PLAY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROG |
|
CH |
NAME |
|
|
||
|
|
|
|
|
1 |
C1 2 |
AAB |
|
|
|||
OK |
|
|
|
2 |
C0 3 |
CDE |
|
|
||||
|
|
|
3 |
C5 6 |
|
|
|
|||||
|
|
|
4 |
C2 7 |
|
|
|
|||||
|
|
|
5 |
C0 9 |
FGH |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
MOVE PROGRAM |
: |
|
|
|
|
|
|
||
|
|
|
ERASE PROGRAM |
: |
CLEAR |
|
|
|
EXIT : MENU
continued
Changing/disabling programme positions 23
3
PLAY
OK
Press M/m to highlight the row which you want to change the programme position, then press ,.
To display other pages for programme positions 6 to 60, press M/m repeatedly.
CHANNEL LIST
PROG |
CH |
NAME |
1 |
C1 2 |
AAB |
2 |
C0 3 |
CDE |
3C5 6
4C2 7
5 |
C0 9 |
|
|
|
FGH |
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|
|
|
|
||
SET STATION NAME |
|
: |
|
|
|
|
CONFIRM |
|
: |
OK |
|
EXIT : MENU
4
PLAY
OK
Press M/m until the selected channel row moves to the desired programme position.
The selected channel is inserted at the new programme position and the intermediate channels are displaced to fill the gap.
|
CHANNEL LIST |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
PROG |
CH |
|
|
|
NAME |
|
||
|
1 |
|
C0 3 |
|
|
|
CDE |
|
||
2 |
|
C5 6 |
|
|
|
|
|
|
||
|
|
3 |
|
C1 2 |
|
|
|
AAB |
|
|
|
|
4 |
|
C2 7 |
|
|
|
|
|
|
5 |
|
C0 9 |
|
|
|
FGH |
||||
|
|
|
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|||
|
|
|
|
|
|
|||||
SET STATION NAME |
|
: |
|
|
|
|
|
|||
CONFIRM |
|
: |
OK |
|
EXIT : MENU
5 |
Press OK to confirm the setting. |
|
PLAY
OK
6
7
To change the programme position of another station, repeat steps 3 through 5.
Press MENU to exit the menu.
MENU
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
• The menu disappears automatically if you don’t proceed for more than a few minutes.
24 Changing/disabling programme positions
After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons.
Before you start… |
|
|
• Turn on the VCR and the TV. |
|
CLEAR |
• Set the TV to the video channel. |
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
|
0 |
|
MENU
M/m
OK
Started Getting
1
2
Press MENU, then press M/m to highlight
MENU
LISTS, and press OK.
PLAY
OK
LISTS |
|
|
CHANNEL LIST |
|
|
TIMER LIST |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
|
Press M/m to highlight CHANNEL LIST, |
|
|
|
|
|
|
|
|
|
|
|
|
then press OK. |
|
|
|
|
|
|
|
|
|
|
|
|
|
CHANNEL LIST |
|
|
|
|||||||
PLAY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROG |
|
CH |
NAME |
|
|
||
|
|
|
|
|
1 |
C1 2 |
AAB |
|
|
|||
OK |
|
|
|
2 |
C0 3 |
CDE |
|
|
||||
|
|
|
3 |
C5 6 |
|
|
|
|||||
|
|
|
4 |
C2 7 |
|
|
|
|||||
|
|
|
5 |
C0 9 |
FGH |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
MOVE PROGRAM |
: |
|
|
|
|
|
|
||
|
|
|
ERASE PROGRAM |
: |
CLEAR |
|
|
|
EXIT : MENU
continued
Changing/disabling programme positions 25
3
4
5
6
|
Press M/m to highlight the row which you |
|
|
|
|
|
|
|
|
|
|
|
|
want to disable. |
|
|
|
|
|
|
|
|
|
|
|
|
|
CHANNEL LIST |
|
|
|
|||||||
PLAY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROG |
|
CH |
NAME |
|
|
||
|
|
|
|
1 |
C1 2 |
AAB |
|
|
||||
OK |
|
|
|
2 |
C0 3 |
CDE |
|
|
||||
|
|
|
|
3 |
C5 6 |
|
|
|
||||
|
|
|
|
|
4 |
C2 7 |
|
|
|
|||
|
|
|
5 |
C0 9 |
FGH |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
MOVE PROGRAM |
: |
|
|
|
|
|
|
||
|
|
|
ERASE PROGRAM |
: |
CLEAR |
|
|
|
EXIT : MENU
Press CLEAR.
CLEAR
The selected row will be cleared as shown on the right.
|
CHANNEL LIST |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROG |
|
CH |
NAME |
|
||
|
1 |
C1 2 |
AAB |
|
||||
2 |
C0 3 |
CDE |
||||||
|
|
3 |
|
|
|
|
|
|
|
|
4 |
C2 7 |
|
|
|||
5 |
C0 9 |
FGH |
||||||
|
|
|
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
||
|
|
|
|
|
||||
MOVE PROGRAM |
: |
|
|
|
|
|
||
ERASE PROGRAM |
: |
CLEAR |
|
|
EXIT : MENU
Repeat steps 3 and 4 for any other programme positions you want to disable.
Press MENU to exit the menu.
MENU
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Notes
•The menu disappears automatically if you don’t proceed for more than a few minutes.
•Be sure to select the programme position you want to disable correctly. If you disable a programme position by mistake, you need to reset that channel manually.
26 Changing/disabling programme positions
Changing the station names |
0 |
|
You can change or enter the station names |
||
|
||
(up to 5 characters). The VCR must receive |
|
|
channel information (for instance, |
|
|
SMARTLINK information) for station names |
|
|
to appear automatically. |
MENU |
|
Before you start… |
|
|
• Turn on the VCR and the TV. |
|
|
• Set the TV to the video channel. |
|
|
|
M/m/</, |
|
|
OK |
Started Getting
1
2
3
Press MENU, then press M/m to highlight
MENU
LISTS and press OK.
PLAY
OK
LISTS |
|
|
CHANNEL LIST |
|
|
TIMER LIST |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
|
Press M/m to highlight CHANNEL LIST, |
|
|
|
|
|
|
|
|
|
|
|
|
then press OK. |
|
|
|
|
|
|
|
|
|
|
|
|
|
CHANNEL LIST |
|
|
|
|||||||
PLAY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROG |
|
CH |
NAME |
|
|
||
|
|
|
|
|
1 |
C1 2 |
AAB |
|
|
|||
OK |
|
|
|
2 |
C0 3 |
CDE |
|
|
||||
|
|
|
3 |
C5 6 |
|
|
|
|||||
|
|
|
4 |
C2 7 |
|
|
|
|||||
|
|
|
5 |
C0 9 |
FGH |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SELECT |
: |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||||
|
|
|
MOVE PROGRAM |
: |
|
|
|
|
|
|
||
|
|
|
ERASE PROGRAM |
: |
CLEAR |
|
|
|
EXIT : MENU
PLAY
OK
Press M/m to highlight the row which you want to change or enter the station name, then press ,.
To display other pages for programme positions 6 to 60, press M/m repeatedly.
CHANNEL LIST
PROG |
CH |
NAME |
1 |
C1 2 |
AAB |
2 |
C0 3 |
CDE |
3C5 6
4C2 7
5 |
C0 9 |
|
|
|
FGH |
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|
|
|
|
||
SET STATION NAME |
|
: |
|
|
|
|
CONFIRM |
|
: |
OK |
|
EXIT : MENU
continued
Changing/disabling programme positions 27
4
5
6
7
Press ,.
PLAY
OK
CHANNEL LIST
|
PROG |
CH |
|
NAME |
|
||
|
1 |
C1 2 |
|
AAB |
|
||
|
2 |
C0 3 |
|
CDE |
|
||
3 |
C5 6 |
|
|
|
|
|
|
4 |
C2 7 |
|
|
|
|
|
|
5 |
C0 9 |
|
FGH |
||||
|
|
|
|
|
|
|
|
SELECT A CHARACTER |
: |
|
|
|
|
||
|
|
|
|
||||
NEXT |
|
: |
|
|
|
|
|
CONFIRM |
|
: |
OK |
|
|
EXIT : MENU
PLAY
OK
Enter the station name.
1Press M/m to select a character. Each time you press M, the character changes as shown below.
A t B t … t Z t a t b t … t z t 0 t 1 t … t 9 t (symbols) t (blank space) t A
CHANNEL LIST
|
PROG |
CH |
|
NAME |
|
||
|
1 |
C1 2 |
|
CAB |
|
||
|
2 |
C0 3 |
|
CDE |
|
||
3 |
C5 6 |
|
|
|
|
|
|
4 |
C2 7 |
|
|
|
|
|
|
5 |
C0 9 |
|
FGH |
||||
|
|
|
|
|
|
|
|
SELECT A CHARACTER |
: |
|
|
|
|
||
|
|
|
|
||||
NEXT |
|
: |
|
|
|
|
|
CONFIRM |
|
: |
OK |
|
|
EXIT : MENU
2Press , to set the next character. The next space is highlighted.
To correct a character, press </, until the character you want to correct is highlighted, then reset it.
You can set up to 5 characters for the station name.
Press OK to confirm the new name.
PLAY
OK
Press MENU to exit the menu.
MENU
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Notes
•The menu disappears automatically if you don’t proceed for more than a few minutes.
•If you enter a symbol in step 5, it will appear as a blank space in the display window.
28 Changing/disabling programme positions