Andrew Burrows Crankshaft seal / Removal 28/03/16
Crankshaft rear seal, removal
Remove flywheel.
See pages .
Remove lip seal.
Use tool 6400 + 0192.
Take care to not damage the crankshaft contact face of the seal during extraction.
Tools
Specific tools
Illustration |
RENAULT |
Designation |
Manufacturer's |
Manufacturer's code N° |
Scale |
Qty |
|
TRUCKS part N° |
|
reference N° |
|
|
|
|
7409990192 |
PULLER |
|
|
2 |
1 |
7409996400 |
PULLER |
2 |
1 |
1 / 2
Andrew Burrows Crankshaft seal / Removal 28/03/16
2 / 2
Andrew Burrows Crankshaft seal / Fitting 28/03/16
Crankshaft rear seal, fitting
Clean and carefully inspect the contact faces of seal.
Mount tool 0166.
Check that the tool is correctly placed on the locating dowel before tightening the bolts.
1 / 3
Andrew Burrows Crankshaft seal / Fitting 28/03/16 |
The seal is supplied fitted to a protective ring that is placed on the assembly tool. It is essential to hold the seal to the ring until it is finally installed in the case.Do not apply grease to the lips.Any gasket that has been removed from its ring must not be re-used.
Fit protective ring (1) to tool 0166.
2 / 3
Andrew Burrows Crankshaft seal / Fitting 28/03/16
Match the direction of orientation.
Drive in seal as far as abutment.
Withdraw tool 0166.
Fit flywheel.
See pages .
Tools
Specific tools
Illustration |
RENAULT |
Designation |
Manufacturer's |
Manufacturer's code N° |
Scale |
Qty |
|
TRUCKS part N° |
|
reference N° |
|
|
|
|
7409990166 |
PUSHER |
|
|
1 |
1 |
|
|
|
|
|
|
|
3 / 3
Andrew Burrows Engine flywheel / Removal 28/03/16
Engine flywheel, removal
Removal
Unplug connector (1).
Remove engine speed sensor (2).
1 / 5
Andrew Burrows Engine flywheel / Removal 28/03/16
Remove pilot bearing (1).
Use tool 2740.
Retain the flywheel against motion using tool 1380.
2 / 5
Andrew Burrows Engine flywheel / Removal 28/03/16
Loosen bolts (1) proceeding in the reverse sequence to tightening.
See pages .
Withdraw tool 1380.
Mount tool 1207.
3 / 5
Andrew Burrows Engine flywheel / Removal 28/03/16
Use a spacer (A) length: 50 mm thickness: 5 mm. Remove bolts (1).
Remove flywheel (2). Use lifting tackle.
Ring gear
Disassembly
Remove ring gear.
4 / 5
Andrew Burrows Engine flywheel / Removal 28/03/16 |
Tools
Specific tools
Illustration |
RENAULT |
Designation |
Manufacturer's |
Manufacturer's code N° |
Scale |
Qty |
|
TRUCKS part N° |
|
reference N° |
|
|
|
|
5000261207 |
HOOK (ENGINE |
|
|
1 |
1 |
|
|
FLYWHEEL) |
|
|
|
|
|
|
|
|
|
|
|
|
5000261380 |
CONTROL |
|
|
1 |
1 |
|
|
|
|
|
|
|
|
5000262740 |
PULLER |
|
|
1 |
1 |
|
|
|
|
|
|
|
5 / 5
Andrew Burrows Engine flywheel / Fitting 28/03/16
Engine flywheel, fitting
Ring gear
Assembly
Wear heat-resistant gloves for protection.
Heat at 200°C.
1 / 9
Loading...