TGA650.fm Page 1 Wednesday, July 13, 2005 3:16 PM
5.8 GHz Expandable Cordless Handset
Model No. KX-TGA650
Installation Manual
PLEASE READ BEFORE USE AND SAVE.
This handset is an accessory cordless handset, for use with Panasonic base units KX-TG6500/KX-TG6502/KX-FG6550. This installation manual only describes the steps necessary to start up the handset. Please read the base unit operating instructions for further details.
Accessories (included) For extra orders, call 1-800-332-5368.
ACharger Unit . . . . . . . . . . . . . . . . . . . . . . . . . |
1 |
ABattery . . . . . . . . . . . . . . . . . . . |
1 |
Charger Order No. PQLV30024ZB |
|
Order No. HHR-P104 |
|
AC Adaptor Order No. KX-TCA1-G (KX-TCA1) |
ABelt Clip . . . . . . . . . . . . . . . . . . |
1 |
|
AHandset Cover. . . . . . . . . . . . . . . . . . . . . . . . |
1 |
Order No. PQKE10377Z5 |
|
Order No. PQYNTG6500BR |
|
|
|
Installation
Connecting the Charger unit
Power Outlet
(AC 120 V, 60 Hz)
AC Adaptor
•USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G).
•The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)
•The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.
Installing the battery
Insert the battery (1), and press it down until it snaps into the compartment (2). Close the cover.
2
1
For assistance, please call: 1-800-211-PANA(7262)
– 1 – |
PQQX14269YA S0604-2075 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TGA650.fm Page 2 Wednesday, July 13, 2005 3:16 PM
Charging the battery
Place the handset on the charger and charge for 6 hours before initial use.
•The unit beeps once, the CHARGE indicator lights and “Charging” is displayed.
•When the battery is fully charged, “Charge completed” is displayed if there are no new calls in the Caller List.
•Recharge the battery when:
—“Recharge battery” is displayed on the handset,
—“3” flashes, or
—the handset beeps intermittently while it is in use.
Charge Contacts
CHARGE Indicator
•If the battery has been discharged, the handset will display “Charge for 6 HRS” and “4” when you place the handset on the charger. The handset will not work unless the battery is charged. Continue charging.
Handset battery information
After your Panasonic battery is fully charged, you can expect the following performance:
Operation |
Operating time |
While in use (TALK) |
Up to 5 hours |
|
|
While not in use (Standby) |
Up to 11 days |
|
|
While using the Clarity Booster feature |
Up to 3 hours |
|
|
•Clean the charge contacts of the handset and the charger with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly.
Belt Clip
You can hang the handset on your belt or pocket using the included belt clip.
To attach the belt clip |
To remove the belt clip |
|
While pressing the top of the clip (1), |
|
pull the right edge in the direction of the |
|
arrow (2). |
B
A
– 2 –
TGA650.fm Page 3 Wednesday, July 13, 2005 3:16 PM
Registration
This cordless handset, KX-TGA650, must be registered to a KX-TG6500/KX-TG6502/ KX-FG6550 base unit. The handset will be assigned the extension number at registration. Only one handset can be registered at a time. Charge the battery fully. Make sure the base unit and the other handsets are not being used. Have both the handset and base unit nearby during registration.
[LOCATOR/INTERCOM/
TRANSFER]
CHARGE Indicator
1[-]
Press LOCATOR on base unit for 3 sec.
Then press OKL
BACK OK
To operate “ O K ”, press the right soft key.
• Base unit model shown here is KX-TG6500/KX-TG6502.
The handset display shows the instructions as shown on the right.
Press LOCATOR on base unit for 3 sec.
Then press OKL
BACK PLAY O K
1Base unit: Press and hold [LOCATOR/INTERCOM/TRANSFER] for 3 seconds.
•On the KX-TG6500/KX-TG6502, the CHARGE indicator flashes. After the CHARGE indicator starts flashing, the rest of the procedure must be completed within 1 minute.
•On the KX-FG6550, “HS REGISTRATION” is displayed. The rest of the procedure must be completed within 1 minute.
2Handset:
(1)Press the soft key ( O K ).
(2)Wait until a long beep sounds and the display shows the new extension number.
• Registration is complete.
IN USE SPIPRIVACY1[-]
Handset
Registering
Ex. Extension number 2
IN USE SPIPRIVACY1[2]
Handset [2] Registered
•The registered number “[1]” to “[4]” is shown on the top right of the display.
•You can stop registration by pressing [OFF] on the handset and pressing [LOCATOR/ INTERCOM/TRANSFER] on the base unit.
•Do not try to register KX-TGA650 to a KX-TG5200/KX-TG5202/KX-TG5210/KX-TG5212/ KX-TG5230/KX-TG5240/KX-TG5243/KX-FPG391 base unit. If you do, “Wrong handset Refer to manual” will be displayed. The correct base unit for this handset KX-TGA650 is KX-TG6500/KX-TG6502/KX-FG6550.
To cancel the handset registration, please see your base unit Operating Instructions.
For assistance, please call: 1-800-211-PANA(7262)
– 3 –
TGA650.fm Page 4 Wednesday, July 13, 2005 3:16 PM
Selecting the display language
You can select either “English” or “Spanish” as the display language. The factory preset is “English”.
Press [MENU] N[d] or [B] to select “Initial setting” NSoft key ( |
|
|
|
) N |
|
|||||||
|
SELECT |
|
||||||||||
N[d] or [B] to select “Change language” NSoft key ( |
|
) NSoft |
|
key ( |
|
|
|
) |
||||
SELECT |
|
|
|
|||||||||
to select “Español”, or soft key ( |
|
) to select “English |
” N |
Soft key ( |
|
) for |
|
|||||
ENGLISH |
GUARDAR |
|
||||||||||
Spanish, or soft key ( |
|
) for English N[OFF] |
|
|||||||||
SAVE |
|
Optional Headset
Connecting an optional headset to the handset allows a hands-free phone conversation. Please use only a Panasonic KX-TCA60, KX-TCA86, KX-TCA88, KX-TCA88HA, KX-TCA91, KX-TCA92 or KX-TCA98 headset. To order, call the accessories telephone number on page 1.
Connecting an optional headset
Open the headset jack cover, and insert the headset plug into the headset jack as shown below.
Headset Jack
• Headset sold separately. Model shown here is KX-TCA88.
Wall Mounting
The charger can be wall mounted. Connect the AC adaptor. Install screws using the wall template (see below). Mount the charger (A). Slide it down (B), then slide down to the right (C) until it is secured.
|
2.45 cm |
|
|
(31⁄ ") |
|
|
32 |
|
|
|
A |
|
|
B |
|
Screws |
C |
|
To Power |
|
|
Outlet |
|
2.45 cm |
Wall Template |
|
(31⁄32") |
|
|
|
– 4 – |
|