Long-barrel Inductive Proximity Sensor
E2E2
CSM_E2E2_DS_E_2_2
Proximity Sensor with a Long Screw
Length
•Increased tightening strength. Cable protectors provided as a standard feature.
•Increased indicator visibility. A milled section for wrench grip on all models.
Be sure to read Safety Precautions on page 9.
Ordering Information
Sensors
DC 2-Wire Models
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
|
|
Appearance |
|
|
|
Sensing distance |
|
Operation mode |
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NO |
|
NC |
Shielded |
|
|
|
|
|
M12 |
|
|
3 mm |
|
|
|
|
|
|
|
|
|
|
|
E2E2-X3D1 2M * |
|
E2E2-X3D2 2M |
|||||
|
|
|
|
|
|
M18 |
|
|
7 |
|
|
mm |
|
|
|
|
|
|
|
|
E2E2-X7D1 2M * |
|
E2E2-X7D2 2M |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
M30 |
|
|
|
|
|
|
|
|
10 mm |
|
|
|
|
|
E2E2-X10D1 2M * |
|
E2E2-X10D2 2M |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
|
|
|
|
M12 |
|
|
8 |
|
mm |
|
|
|
|
|
|
E2E2-X8MD1 2M * |
|
E2E2-X8MD2 2M |
||||||||
Unshielded |
|
|
|
|
|
|
|
|||||||||||||||||||||
|
|
|
|
|
|
M18 |
|
|
|
|
|
|
|
|
|
|
14 mm |
|
|
|
E2E2-X14MD1 2M * |
|
E2E2-X14MD2 2M |
|||||
|
|
|
|
|
|
M30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X20MD1 2M * |
|
E2E2-X20MD2 2M |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
20 mm |
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* Models with different frequencies are also available. The model numbers are E2E2-X@D15 (example: E2E2-X3D15).
DC 3-Wire Models
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
|
Appearance |
|
|
|
|
Sensing distance |
|
Operation mode |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NO |
|
NC |
Shielded |
|
M12 |
|
|
2 mm |
|
|
|
|
|
|
|
|
E2E2-X2C1 2M |
|
E2E2-X2C2 2M |
|||||||
|
|
|
|
|
|
|
M18 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X5C1 2M |
|
E2E2-X5C2 2M |
|
|
|
|
|
|
|
|
|
|
5 mm |
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
M30 |
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X10C1 2M |
|
E2E2-X10C2 2M |
|
|
|
|
|
|
|
|
|
|
|
|
|
10 mm |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
M12 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X5MC1 2M |
|
E2E2-X5MC2 2M |
Unshielded |
|
|
|
|
|
|
|
|
5 mm |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
M18 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X10MC1 2M |
|
E2E2-X10MC2 2M |
|
|
|
|
|
|
|
|
|
|
|
|
10 mm |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
M30 |
|
|
|
|
|
|
|
|
|
|
|
E2E2-X18MC1 2M |
|
E2E2-X18MC2 2M |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
18 |
mm |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC 2-Wire Models
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
|
Appearance |
|
|
|
|
Sensing distance |
|
Operation mode |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NO |
|
NC |
Shielded |
|
M12 |
|
|
2 mm |
|
|
|
|
|
|
|
|
E2E2-X2Y1 2M |
|
E2E2-X2Y2 2M |
|||||||
|
|
|
|
|
|
|
M18 |
|
|
|
5 mm |
|
|
|
|
|
|
E2E2-X5Y1 2M |
|
E2E2-X5Y2 2M |
|||
|
|
|
|
|
|
|
M30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X10Y1 2M |
|
E2E2-X10Y2 2M |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
10 mm |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Unshielded |
|
|
|
|
|
M12 |
|
|
|
5 mm |
|
|
|
|
|
E2E2-X5MY1 2M |
|
E2E2-X5MY2 2M |
|||||
|
|
|
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
M18 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X10MY1 2M |
|
E2E2-X10MY2 2M |
|
|
|
|
|
|
|
|
|
|
|
|
10 mm |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M30 |
|
|
|
|
|
|
|
18 |
mm |
|
|
E2E2-X18MY1 2M |
|
E2E2-X18MY2 2M |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1
E2E2
Accessories (Order Separately)
Mounting Brackets
Protective Covers
Sputter Protective Covers
Ratings and Specifications
E2E2-X@D@ DC 2-Wire Models
|
|
Size |
M12 |
M18 |
M30 |
||||
|
|
Shielding |
Shielded |
Unshielded |
Shielded |
Unshielded |
Shielded |
Unshielded |
|
Item |
Model |
E2E2-X3D@ |
E2E2-X8MD@ |
E2E2-X7D@ |
E2E2-X14MD@ |
E2E2-X10D@ |
E2E2-X20MD@ |
||
Sensing distance |
3 mm±10% |
8 mm±10% |
7 mm±10% |
14 mm±10% |
10 mm±10% |
20 mm±10% |
|||
Set distance *1 |
0 to 2.4 mm |
0 to 6.4 mm |
0 to 5.6 mm |
0 to 11.2 mm |
0 to 8 mm |
0 to 16 mm |
|||
Differential travel |
10% max. of sensing distance |
|
|
|
|
||||
Sensing object |
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on |
||||||||
page 5.) |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
||
Standard sensing object |
Iron, |
Iron, |
Iron, |
Iron, |
Iron, |
Iron, |
|||
12 × 12 × 1 mm |
30 × 30 × 1 mm |
18 × 18 × 1 mm |
30 × 30 × 1 mm |
30 × 30 × 1 mm |
54 × 54 × 1 mm |
||||
|
|
|
|||||||
Response frequency *2 |
1 kHz |
800 Hz |
500 Hz |
400 Hz |
|
100 Hz |
|||
Power supply voltage |
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. |
|
|
||||||
(operating voltage range) |
|
|
|||||||
|
|
|
|
|
|
||||
Leakage current |
0.8 mA max. |
|
|
|
|
|
|||
Control |
|
Switching |
3 to 100 mA |
|
|
|
|
|
|
|
capacity |
|
|
|
|
|
|||
output |
|
|
|
|
|
|
|
||
|
Residual voltage |
3 V max. (Load current: 100 mA, Cable length: 2 m) |
|
|
|
||||
|
|
|
|
|
|||||
Indicators |
|
D1 Models: Operation indicator (red) and setting indicator (green) |
|
|
|||||
|
D2 Models: Operation indicator (red) |
|
|
|
|||||
|
|
|
|
|
|
||||
Operation mode |
D1 Models: NO |
Refer to the timing charts under I/O Circuit Diagrams on page 8 for details. |
|||||||
(with sensing object ap- |
|||||||||
proaching) |
D2 Models: NC |
|
|
|
|
|
|||
|
|
|
|
|
|
||||
Protection circuits |
Surge absorber, Load short-circuit protection |
|
|
|
|||||
Ambient temperature |
Operating/Storage: −25 to 70°C (with no icing or condensation) |
|
|
||||||
Ambient humidity |
Operating/Storage: 35% to 95% (with no condensation) |
|
|
||||||
Temperature influence |
±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C |
|
|||||||
Voltage influence |
±1% max. of sensing distance at rated voltage in the rated voltage ±15% range |
|
|||||||
Insulation resistance |
50 MΩ min. (at 500 VDC) between current-carrying parts and case |
|
|
||||||
Dielectric strength |
1000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case |
|
|||||||
Vibration resistance |
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
|
|||||||
(destruction) |
|
||||||||
|
|
|
|
|
|
||||
Shock resistance |
1,000 m/s2 10 times each in X, Y, and Z directions |
|
|
|
|||||
(destruction) |
|
|
|
||||||
|
|
|
|
|
|
||||
Degree of protection |
IEC IP67, in-house standard for oil resistance |
|
|
|
|||||
Connection method |
Pre-wired Models (Standard cable length: 2 m) |
|
|
|
|||||
Weight (packed state) |
Approx. 65 g |
|
Approx. 150 g |
|
Approx. 210 g |
|
|||
|
|
Case |
Brass |
|
|
|
|
|
|
Materi- |
|
Sensing surface |
PBT |
|
|
|
|
|
|
als |
|
Clamping nuts |
Nickel-plated brass |
|
|
|
|
||
|
|
Toothed washer |
Zinc-plated iron |
|
|
|
|
|
|
Accessories |
Instruction sheet |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
*1. Use the E2E2 within the range in which the setting indicator (green LED) is ON (except D2 Models).
*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
2
|
|
|
|
|
|
|
|
E2E2 |
|
|
|
|
|
|
|
|
|
||
E2E2-X@C@ DC 3-Wire Models |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
Size |
M12 |
M18 |
M30 |
||||
|
|
Shielding |
Shielded |
Unshielded |
Shielded |
Unshielded |
Shielded |
Unshielded |
|
Item |
Model |
E2E2-X2C@ |
E2E2-X5MC@ |
E2E2-X5C@ |
E2E2-X10MC@ |
E2E2-X10C@ |
E2E2-X18MC@ |
||
Sensing distance |
2 mm±10% |
5 mm±10% |
5 mm±10% |
10 mm±10% |
10 mm±10% |
18 mm±10% |
|||
Set distance |
0 to 1.6 mm |
0 to 4 mm |
0 to 4 mm |
0 to 8 mm |
0 to 8 mm |
0 to 14 mm |
|||
Differential travel |
10% max. of sensing distance |
|
|
|
|
||||
Sensing object |
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on |
||||||||
page 5.) |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
||
Standard sensing object |
Iron, |
Iron, |
Iron, |
Iron, |
Iron, |
Iron, |
|||
12 × 12 × 1 mm |
15 × 15 × 1 mm |
18 × 18 × 1 mm |
30 × 30 × 1 mm |
30 × 30 × 1 mm |
54 × 54 × 1 mm |
||||
|
|
|
|||||||
Response frequency *1 |
1.5 kHz |
400 Hz |
600 Hz |
200 Hz |
400 Hz |
100 Hz |
|||
Power supply voltage (op- |
12 to 24 VDC (10 to 55 VDC), ripple (p-p): 10% max. |
|
|
||||||
erating voltage range) *2 |
|
|
|||||||
|
|
|
|
|
|
||||
Leakage current |
13 mA max. |
|
|
|
|
|
|||
Control |
|
Load current |
NPN open-collector output, 200 mA max. (55 VDC max.) |
|
|
||||
output |
|
Residual voltage |
2 V max. (Load current: 200 mA, Cable length: 2 m) |
|
|
|
|||
Indicators |
|
Operation indicator (red) |
|
|
|
|
|||
Operation mode |
C1 Models: NO |
Refer to the timing charts under I/O Circuit Diagrams on page 8 for details. |
|||||||
(with sensing object ap- |
|||||||||
proaching) |
C2 Models: NC |
|
|
|
|
|
|||
|
|
|
|
|
|
||||
Protection circuits |
Reverse polarity protection, Surge absorber, Load short-circuit protection |
|
|||||||
Ambient temperature |
Operating/Storage: −40 to 85°C (with no icing or condensation) |
|
|
||||||
Ambient humidity |
Operating/Storage: 35% to 95% (with no condensation) |
|
|
||||||
Temperature influence |
±15% max. of sensing distance at 23°C in the temperature range of −40 to 85°C |
|
|||||||
±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C |
|
||||||||
|
|
|
|
||||||
Voltage influence |
±1% max. of sensing distance at rated voltage in the rated voltage ±15% range |
|
|||||||
Insulation resistance |
50 MΩ min. (at 500 VDC) between current-carrying parts and case |
|
|
||||||
Dielectric strength |
1,000 VAC, 50/60 Hz for 1 minute between current carry parts and case |
|
|||||||
Vibration resistance |
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
|
|||||||
(destruction) |
|
||||||||
|
|
|
|
|
|
||||
Shock resistance |
1,000 m/s2 10 times each in X, Y, and Z directions |
|
|
|
|||||
(destruction) |
|
|
|
||||||
|
|
|
|
|
|
||||
Degree of protection |
IEC IP67, in-house standard for oil resistance |
|
|
|
|||||
Connection method |
Pre-wired Models (Standard cable length: 2 m) and Connector Models |
|
|||||||
Weight (packed state) |
Approx. 75 g |
|
Approx. 160 g |
|
Approx. 220 g |
|
|||
|
|
Case |
Brass |
|
|
|
|
|
|
Materi- |
|
Sensing surface |
PBT |
|
|
|
|
|
|
als |
|
Clamping nuts |
Nickel-plated brass |
|
|
|
|
||
|
|
Toothed washer |
Zinc-plated iron |
|
|
|
|
|
|
Accessories |
Instruction sheet |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
*1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
*2. A full-wave rectification power supply of 24 VDC ±20% (average value) can be used.
3
|
|
|
|
|
|
|
|
|
E2E2 |
|
|
|
|
|
|
|
|
|
|
|
|
E2E2-X@Y@ AC 2-Wire Models |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
Size |
M12 |
M18 |
|
M30 |
|
|||
|
|
Shielding |
Shielded |
Unshielded |
Shielded |
Unshielded |
|
Shielded |
Unshielded |
|
Item |
Model |
E2E2-X2Y@ |
E2E2-X5MY@ |
E2E2-X5Y@ |
E2E2-X10MY@ |
|
E2E2-X10Y@ |
E2E2-X18MY@ |
|
|
Sensing distance |
2 mm±10% |
5 mm±10% |
5 mm±10% |
10 mm±10% |
|
10 mm±10% |
18 mm±10% |
|
||
Set distance |
0 to 1.6 mm |
0 to 4 mm |
0 to 4 mm |
0 to 8 mm |
|
0 to 8 mm |
0 to 14 mm |
|
||
Differential travel |
10% max. of sensing distance |
|
|
|
|
|
|
|||
Sensing object |
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on |
|
||||||||
page 5.) |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
Standard sensing object |
Iron, |
Iron, |
Iron, |
Iron, |
|
Iron, |
Iron, |
|
||
12 × 12 × 1 mm |
15 × 15 × 1 mm |
18 × 18 × 1 mm |
30 × 30 × 1 mm |
|
30 × 30 × 1 mm |
54 × 54 × 1 mm |
|
|||
|
|
|
|
|
||||||
Response frequency |
25 Hz |
|
|
|
|
|
|
|
||
Power supply voltage (op- |
24 to 240 VAC (20 to 264 VAC), 50/60 Hz |
|
|
|
|
|
||||
erating voltage range) *1 |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|||
Leakage current |
1.7 mA max. |
|
|
|
|
|
|
|
||
Control |
|
Load current *2 |
5 to 200 mA |
|
5 to 300 mA |
|
|
|
|
|
output |
|
Residual voltage |
Refer to Engineering Data on page 5. |
|
|
|
|
|
||
Indicators |
|
Operation indicator (red) |
|
|
|
|
|
|
||
Operation mode |
Y1 Models: NO |
Refer to the timing charts under I/O Circuit Diagrams on page 8 for details. |
|
|||||||
(with sensing object ap- |
|
|||||||||
proaching) |
Y2 Models: NC |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|||
Ambient temperature *1, 2 |
Operating/Storage: −40 to 85°C (with no icing or condensation) |
|
|
|
||||||
Ambient humidity |
Operating/Storage: 35% to 95% (with no condensation) |
|
|
|
||||||
Temperature influence |
±15% max. of sensing distance at 23°C in the temperature range of −40 to 85°C, |
|
|
|||||||
±10% max. of sensing distance at 23°C in the temperature range of −25 to 70°C |
|
|
||||||||
|
|
|
|
|
||||||
Voltage influence |
±1% max. of sensing distance at rated voltage in the rated voltage ±15% range |
|
|
|||||||
Insulation resistance |
50 MΩ min. (at 500 VDC) between current-carrying parts and case |
|
|
|
||||||
Dielectric strength |
4,000 VAC, 50/60 Hz for 1 minute between current carry parts and case |
|
|
|||||||
Vibration resistance |
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions |
|
|
|||||||
(destruction) |
|
|
||||||||
|
|
|
|
|
|
|
|
|||
Shock resistance |
1,000 m/s2 10 times each in X, Y, and Z directions |
|
|
|
|
|
||||
(destruction) |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|||
Degree of protection |
IEC IP67, in-house standard for oil resistance |
|
|
|
|
|
||||
Connection method |
Pre-wired Models (Standard cable length: 2 m) and Connector Models |
|
|
|
||||||
Weight (packed state) |
Approx. 65 g |
|
Approx. 150 g |
|
|
Approx. 210 g |
|
|
||
|
|
Case |
Brass |
|
|
|
|
|
|
|
Materi- |
|
Sensing surface |
PBT |
|
|
|
|
|
|
|
als |
|
Clamping nuts |
Nickel-plated brass |
|
|
|
|
|
|
|
|
|
Toothed washer |
Zinc-plated iron |
|
|
|
|
|
|
|
Accessories |
Instruction sheet |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
*1. When supplying 24 VAC to any of the above models, make sure that the operating ambient temperature range is at least −25°C to 85°C.
*2. When using an M18 or M30 Connector Model at an ambient temperature between 70 and 85°C, make sure that the Sensor has a control output (load current) of 5 to 200 mA max.
4