Page 1
TABLE LAMP
Operation and Safety Notes
Z31207A-BS
Z31207B-BS
Page 2
GB / IE Operation and Safety Notes Page 5
Page 3
1
Z31207A-BS
12345
2
3
Z31207B-BS
1
12345
2
3
3
Page 4
Z31207A-BS
Z31207B-BS
4
Page 5
Table lamp
Introduction
Before using the device for the first time, take time
to familiarise yourself with the product. In addition,
please carefully refer to the operating instructions
and the safety advice below. Only use the product
as instructed and only for the indicated field of application. Keep these instructions in a safe place. If
passing this product on to a third party also include
all documents.
Proper use
This lamp is intended for indoor use in dry and enclosed rooms only. The product is not intended for
commercial use.
Technical data
Nominal voltage: 230 V ∼, 50 Hz
Illuminant: 230 V∼, max. 42 W, E14,
halogen bulb (illuminant not
included in the delivery)
Protection class:
Scope of delivery
Check that all the items and accessories are present
and that the device is in perfect condition immediately after unpacking.
1 Touch Lamp
1 Operating instructions
Safety advice
The right to claim under the warranty shall be rendered invalid in respect of damage caused by the
non-observance of these operating instructions! No
liability is accepted for consequent damage! No
liability is accepted for damage to property or persons caused by improper handling or non-observance of the safety advice!
DANGER OF
LOSS OF LIFE AND ACCIDENT
TO INFANTS AND CHILDREN!
Never leave children unsupervised with the
packaging materials. The packaging material
represents a danger of suffocation. Children
frequently underestimate the dangers. Always
keep the product out of reach of children.
Children or persons who lack knowledge or
experience in handling the device or who have
limited physical, sensory or mental abilities
may not use the device without supervision or
without instruction by a person responsible for
their safety. Children must be supervised at all
times to prevent them from playing with the appliance.
This lamp is designed for indoor use
in dry and enclosed rooms only.
Check the lamp and the mains lead for dam-
age each time before connecting them. Never
use your lamp if you discover that it is damaged in any way.
CAUTION! The lamp shield is not replaceable.
Dispose of the lamp if you find cracks or other
damage to the lamp shield.
This product’s external flexible tube is non-re-
placeable. Hence, if it becomes damaged you
must dispose of the entire product.
Protect the mains lead against sharp edges,
mechanical stresses and hot surfaces.
Always unplug the mains plug from the socket
before installation, dismantling or cleaning.
Disconnect the product from the mains supply if
it is not going to be used for some time (e.g.
holiday).
Only use 230 V ∼ halogen light bulbs with a
E14 base and a maximum output of 42 watt.
Set the lamp in a stable, clean and even place.
from the development of too much heat.
FIRE HAZARD! Fit the light so that
0.5 m
it is at least 0.5 m away from the
material illuminated. Fire can result
5 GB/IE
Page 6
Before initial use
Before assembly, ensure that the mains voltage
available corresponds to the operating voltage
necessary for the lamp (230 V ∼). Do not connect the lamp if this is not the case.
Screw the lamp into the socket until a flawless
contact is enabled. Only use the lamp with an
E14 base.
CAUTION! Use the lamp with a maximum
power output of 42 watt. Using a higher power
output could cause damage to the lamp.
Use halogen bulbs only.
Do not use energy saving bulbs. Energy saving
bulbs are not dimmable.
Operation
Operate the lamp in accordance with the figures.
Please note: This lamp is equipped with a dimmer that regulates the light into 3 different levels of
brightness by touching the metal foot.
Contact your local community or municipal
administration for more details on how to dispose
your worn-out product.
To help protect the environment, please
dispose the product properly, and not in
the household waste, when it has
reached the end of its useful life. Information on collection points and their
opening hours can be obtained from
your local authority.
EMC
Changing the bulb
Before changing the bulb, switch off the lamp
and remove the mains plug from the socket. Let
the existing bulb cool down for 15 minutes.
Cleaning and care
Use a dry, soft and fluff-free cloth for cleaning
and care. Use a slightly moist and a mild deter-
gent to remove stubborn dirt.
Disposal
The packaging is made entirely of recyclable materials which you may dispose
at local recycling facilities.
6 GB/IE
Page 7
IAN 89533
OWIM GmbH & Co. KG
Stiftsbergstraße 1
D-74167 Neckarsulm
Model-No.: Z31207A-BS / Z31207B-BS
Version: 05 / 2013
© by ORFGEN Marketing
Last Information Update: 02 / 2013
Ident.-No.: Z31207A-BS / B-BS022013-6
6
Loading...