Livarno Z31410A-BS, Z31410B-BS User Manual

LED UNDER-CABINET LIGHT

Assembly and safety advice

Z31410A-BS/

Z31410B -BS

Z31410A-BS

2 x

Z31410B-BS

approx.140°

Z31410B-BS

approx.140°

2 x

GB/IEGB/IEGB/IE

LED under-cabinet light

Proper use

The under-unit lights are intended for providing illumination and for mounting on furniture. The under-unit lights can also be mounted on walls. The product may only be used indoors in dry rooms. The lamps cannot be placed. The lights can be mounted on all normally ﬂammable surfaces. This device is intended for indoor use only in a domestic, private household environment.

Description of

re-

parts and features

ON/OFF switch

Socket for connecting lead

LED

Protective cap (for Model B

only)

Connecting lead with mains

plug

Extension connector (for

Model B only)

Mounting bracket

Dowel ø 6 x 30 mm

Screw for wall mounting

Screw for under cabinet

installation

Technical data

Model A

Operating voltage:

Lamps: 60

LED: 60 x 0.1 W Nominal power: max. 7 W Protection category:

230 V~

50 Hz

power LED (LED cannot be replaced)

Model B

Operating voltage:

Lamps: 40

LED: 40 x 0.1 W Nominal power: max. 5 W Protection category:

Safety

230 V~

50 Hz

power LED (LED cannot be replaced)

Safety advice

YOU SHOULD STORE ALL SAFETY INFORMATION AND INSTRUCTIONS IN A SAFE PLACE IN CASE YOU NEED TO REFER TO THEM AGAIN IN THE FUTURE!

J Children or other individuals

who do not know or have no experience of handling this device, or whose physical, sensory or mental abilities are restricted, must not use the device without supervision or instruction by an individual responsible for their safety. Children must be supervised in order to ensure that they do not play with the device.

J Do not attach the light to

damp or conductive substrates.

To avoid danger

to life from electric shock

J Never use your lamp if you

discover that it is damaged in any way.

J If the external ﬂexible cable

or cord of this luminary is damaged, it shall be replaced by a special cord or cord exclusively available from the manufacturer or his service agent.

J For installation, please con-

tact qualiﬁed electrician if you have any doubt.

J Never let the lamp come

into contact with water or other liquids.

J Before assembly, ensure that

the mains voltage (230 V~ 50 Hz) available corresponds to the operating voltage necessary of the light.

To avoid danger

of fire and injury

the lamp has been switched

J Do not use this light for dim-

J Install the lamp so that it is

RISK OF IN-

JURY FROM BURNS! Ensure

oﬀ and allowed to cool before you touch it. In this way you will avoid the danger of burns. Bulbs give oﬀ a lot of heat around the top of the lamp.

mers or electronic switches. It is not suitable for these purposes.

Working safely

protected from moisture and dirt.

85873_livx_Unterbauleuchte_BS.indd 1 07.12.12 10:00

Installation and operation

Installing light

j Use the mounting brackets

and the screws 10 for

under cabinet installation.

j Mark the distance of

200mm for the two ﬁxing holes. Drill the holes: ø approx. 2mm, approx. 15mm deep.

j Position the mounting brack-

ets

according to the

drilled holes and tighten the

screws

j Attach the light to the secured

mounting brackets

j Plug the connection cable

with mains plug socket for the connection cable

j Plug the connection cable

with mains plug mains socket. Your light is now ready for operation.

Mounting

j Use the mounting brackets

7 8

lation.

j Measure up the wall or

mounting surface for drilling the holes. Use a spirit level to improve accuracy.

j Mark the two mounting

holes a distance of approx. 200 mm apart.

j Now drill the mounting

holes (ø approx. 6 mm, depth approx. 30 mm).

CAUTION! Make sure that

you do not damage any electrical cables during this operation.

j Insert the supplied dowels

into the drilled holes.

into the

on a wall

, screws 9 and dowels for wall mounting instal-

j Position the mounting bracket

according to the dowel

, then insert the supplied

screws

into the dowels

and tighten them.

j Attach the light to the secured

mounting brackets

j Plug the connection cable

with mains plug socket for the connection

cable

j Plug the connection cable

with mains plug mains socket. Your light is now ready for operation.

Extensions (See Fig. A)

j Note: Ensure that no more

than 3 under-unit lights of the same type (for model B only) are connected together in series. Connect only same type of lamp only. Don’t connect other type of lamp with this lamp.

j Remove the protective cap

. Connect the two underunit lights to the socket using the extension connec-

tor

. Then you only need one connection lead the power supply.

j CAUTION! First ensure

that all the under-unit lights are connected by an extension connector

you insert the mains lead into the mains socket.

Operation

j Press the ON / OFF switch

to turn the light on / oﬀ.

NOTE: Model B has a rotatable shade (approx. 140°) for direct or indirect lighting.

into the

before

Maintenance and Cleaning

Allow the lamp to cool down

completely.

DANGER

TO LIFE FROM SHOCK! Before carrying out

any tasks on the lamp, switch oﬀ the lamp and disconnect the plug from the mains socket.

TO LIFE FROM SHOCK! For reasons of electri-

cal safety, the light must never be cleaned with water or other ﬂuids or be immersed in water. When cleaning, only use a dry, lint-free cloth.

Disposal

vironmentally-friendly materials. They can be disposed of at your local recycling facility.

for

that, in the European Union, the product has to be disposed of in a separate refuse collection. This applies to the product and to all components bearing this symbol. Products marked in this way may not be disposed of along with normal domestic waste but have to be handed in at a recycling collection point for electrical and electronic appliances. Recycling helps to reduce the consumption of raw materials and to ease the burden on the environment.

EMC

ELECTRIC

DANGER

ELECTRIC

The packaging and ancillary packing consist entirely of en-

The symbol of the

wheelie bin with the line through it means

IAN 85873

OWIM GmbH & Co. KG

Stiftsbergstraße 1 D-74167 Neckarsulm

Model-No.: Z31410A-BS/ Z31410B-BS Version: 12 / 2012

Last Information Update: 12 / 2012 ·

Ident no.:

Z31410A-BS/B-BS122012-6

GB/IE GB/IE GB/IE

85873_livx_Unterbauleuchte_BS.indd 2 07.12.12 10:00