Yamaha XLT1200 User Manual

0 (0)

2003

WaveRunner

XLT1200

OWNER’S/OPERATOR’S

MANUAL

LIT-18626-05-17

U.S.A. Edition

READ THIS MANUAL

CAREFULLY BEFORE OPERATION!

EJU00989

To the owner/operator

Thank you for choosing a Yamaha water-

craft.

This Owner’s/Operator’s Manual contains

information you will need for proper opera-

tion, maintenance, and care. A thorough

understanding of these simple instructions

will help you to obtain maximum enjoyment

from your new Yamaha. If you have any

questions about the operation or mainte-

nance of your watercraft, please consult a

Yamaha dealer.

Because Yamaha has a policy of continu-

ing product improvement, this product may

not be exactly as described in this Owner’s/

Operator’s Manual. Specifications are sub-

ject to change without notice.

This manual should be considered a per-

manent part of this watercraft and should

remain with it even if the watercraft is subse-

quently sold.

EJU01204

Important manual information:

In this manual, information of particular

importance is distinguished in the following

ways:

The Safety Alert Symbol means

ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED!

WARNING

Failure to follow WARNING instructions

could result in severe injury or death to

the machine operator, passengers, a

bystander, or a person inspecting or

repairing the watercraft.

CAUTION:

A CAUTION indicates special precau-

tions that must be taken to avoid damage

to the watercraft.

TE:

A NOTE provides key information to make

procedures easier or clearer.

EJU01173

WaveRunner XLT1200

OWNER’S/OPERATOR’S MANUAL

1st Edition, July 2002

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, USA

is expressly prohibited.

Printed in USA

P/N LIT-18626-05-17

EJU00992

READ THIS OWNER’S/OPERATOR’S MANUAL CAREFULLY

BEFORE OPERATING YOUR WATERCRAFT.

GENERAL AND SAFETY

INFORMATION

FEATURES AND FUNCTIONS

OPERATION

MAINTENANCE AND CARE

TROUBLESHOOTING AND

EMERGENCY PROCEDURES

APPENDIX

EJU00993

GENERAL AND

SAFETY

INFORMATION

Identification numbers

............................1-1

Primary Identification (PRI-ID)

number ...................................................1-1

Hull Identification Number (HIN) ............1-1

Engine serial number .............................1-2

Emission control information

................1-3

Approval label of Emission control

certificate ................................................1-3

Manufactured date label ........................1-3

Important labels

.......................................1-4

Label location .........................................1-4

Warning labels .......................................1-5

Other labels ............................................1-6

Safety information

...................................1-8

Limitations on who may operate the

watercraft ................................................1-8

Cruising limitations .................................1-9

Operation requirements .......................1-10

Recommended equipment ..................1-12

Hazard information ..............................1-13

Watercraft characteristics ....................1-13

Water-skiing .........................................1-14

Rules of the Road

..................................1-16

Steering and sailing rules ....................1-16

Rules when encountering vessels ......1-17

Other special situations .......................1-18

Reading buoys and other markers ...... 1-18

To get more boating safety

information

.............................................1-20

United States Coast Guard .................1-20

Other sources ......................................1-20

Watercraft Education and Training ......1-20

Enjoy your watercraft responsibly

......1-21

1-1

EJU01830

Identification numbers

Record the Primary Identification (PRI-ID)

number, Hull Identification Number (HIN)

and engine serial number in the spaces pro-

vided for assistance when ordering spare

parts from a Yamaha dealer. Also record

and keep these ID numbers in a separate

place in case your watercraft is stolen.

EJU01985

Primary Identification (PRI-ID)

number

Approval number plate (California)

Approval number plate (other states)

The PRI-ID number is stamped on a

label

attached inside the engine compart-

ment.

EJU01205

Hull Identification Number

(HIN)

The HIN is stamped on a plate

attached to the aft deck.

1-2

EJU00997

Engine serial number

The engine serial number is stamped on

a label 3 attached to the engine unit.

1-3

EJU01846

Emission control

information

This engine conforms to 2003 U.S. Envi-

ronmental Protection Agency (EPA) regula-

tions for marine SI engines.

EJU01389

Approval label of Emission

control certificate

This label is attached to the electrical box

and the intake side of the crankcase.

Emission control information label (California)

Emission control information label (other

states)

New Technology; Catalytic converter

EJU01390

Manufactured date label

This label is attached to the electrical box

and the intake side of the crankcase.

Manufactured date label

1-4

EJU00998

Important labels

EJU01351

Label location

1-5

EJU01352

Warning labels

1-6

EJU01354

Other labels

1-7

1-8

EJU01177

Safety information

The safe use and operation of this

watercraft is dependent upon the use of

proper riding techniques, as well as upon

the common sense, good judgment, and

expertise of the operator. Every operator

should know the following requirements

before riding the watercraft.

●

Before operating the watercraft, read the

Owner’s/Operator’s Manual, the Riding

Practice Guide, the Riding Instruction

card and all warning and caution labels

on the watercraft. Also, watch the Basic

Orientation Video provided with your

watercraft. These materials should give

you an understanding of the watercraft

and its operation.

●

Never allow anyone to operate this water-

craft until they too have read the Owner’s/

Operator’s Manual, the Riding Practice

Guide, the Riding Instruction card and all

warning and caution labels, and if possi-

ble watched the Basic Orientation Video.

Showing them the video may help rein-

force the information contained in these

materials.

EJU01159

Limitations on who may

operate the watercraft

●

Yamaha recommends a minimum opera-

tor age of 16 years old.

Adults must supervise use by minors.

Know the operator age and training

requirements for your state. A boating

safety course is recommended and may

be required in your state. You can find

local rules by contacting the United

States Coast Guard (USCG), the National

Association of State Boating Law Admin-

istrators, or your local Power Squadron.

●

This watercraft is designed to carry the

operator and up to 2 passengers. Never

exceed the maximum load limit or allow

more than 3 persons (or 2 persons if a

water-skier is being pulled) to ride the

watercraft at one time.

●

Do not operate the watercraft with any

passengers on board until you have con-

siderable practice and experience riding

alone. Operating the watercraft with pas-

sengers requires more skill. Take the time

to become accustomed to the handling

characteristics of the watercraft before

trying any difficult maneuvers.

Maximum load: 240 kg (530 lb)

Load is the total weight of cargo,

operator and passengers.

1-9

EJU01001

Cruising limitations

●

Scan constantly for people, objects, and

other watercraft. Be alert for conditions

that limit your visibility or block your vision

of others.

●

Operate defensively at safe speeds and

keep a safe distance away from people,

objects, and other watercraft.

●

Do not follow directly behind watercraft or

other boats.

●

Do not go near others to spray or splash

them with water.

●

Avoid sharp turns or other maneuvers

that make it hard for others to avoid you or

understand where you are going.

●

Avoid areas with submerged objects or

shallow water.

●

Ride within your limits and avoid aggres-

sive maneuvers to reduce the risk of loss

of control, ejection, and collision.

●

This is a high performance boat—not a

toy. Sharp turns or jumping wakes or

waves can increase the risk of back/spinal

injury (paralysis), facial injuries, and bro-

ken legs, ankles and other bones. Do not

jump wakes or waves.

●

Do not operate the watercraft in rough

water, bad weather or when visibility is

poor; this may lead to an accident caus-

ing injury or death. Be alert to the possi-

bility of adverse weather. Take note of

weather forecasts and the prevailing

weather conditions before setting out on

your watercraft.

●

As with any water sport, you should not

ride your watercraft without someone else

near by. If you ride further than swimming

distance from shore, you should ride by

another boat or watercraft, but make sure

you stay a safe distance away. It’s good

common sense!

●

Never operate in water that is less than

60 cm (2 ft) deep, otherwise you increase

your chance of hitting a submerged

object, which could result in injury.

1-10

●

This watercraft is not equipped with light-

ing required for night operation. Do not

operate the watercraft after sunset or

before dawn, otherwise you increase the

risk of colliding with another boat, which

could result in severe injury or death.

EJU01160

Operation requirements

●

All riders must wear a Coast Guard

approved personal flotation device (PFD)

that is suitable for personal watercraft

use.

●

Wear protective clothing. Severe internal

injuries can occur if water is forced into

body cavities as a result of falling into

water or being near the jet thrust nozzle.

Normal swimwear does not adequately

protect against forceful water entry into

rectum or vagina. All riders must wear a

wetsuit bottom or clothing that provides

equivalent protection. Such clothing

includes thick, tightly woven, sturdy and

snug-fitting apparel such as denim, but

does not include spandex or similar fab-

rics, like those used in bicycle shorts.

Coast Guard approved PFD

Wetsuit bottom

●

Eye protection is recommended to keep

wind, water, and glare from the sun out of

your eyes while you operate your water-

craft. Restraining straps for eyewear are

made which are designed to float should

your eyewear fall in the water.

Footwear and gloves are recommended.

1-11

●

Helmets meeting Snell or DOT standards

are required for IJSBA-sanctioned races.

You must decide whether to wear a hel-

met while you ride for recreation. You

should know that a helmet could help pro-

tect you in certain kinds of accidents and

that it could injure you in others.

A helmet is designed to provide some

head protection. Although helmets cannot

protect against all foreseeable impacts, a

helmet might reduce your injuries in a col-

lision with a boat or other obstacle.

A helmet may have potential safety haz-

ards, as well. Falling into the water could

risk the chance of the helmet catching

water, commonly known as “bucketing,”

and the resulting strain on your neck

could cause choking, severe and perma-

nent neck injuries, or death. A helmet

could also increase the risk of an accident

if it reduces your vision or hearing, or if it

distracts you or increases your fatigue.

How should you decide if a helmet’s

potential safety benefits outweigh its

potential risks for you? Consider your par-

ticular riding conditions. Consider factors

such as your riding environment and your

riding style and ability. Also consider the

likelihood of traffic congestion, and the

water surface conditions. If you decide to

wear a helmet based upon your riding cir-

cumstances, choose one carefully. Look

for a helmet designed for personal water-

craft use, if possible. Consider a helmet

meeting Snell or DOT standards. If you

will be engaging in closed-course compe-

tition, follow the helmet requirements of

the sanctioning organization.

●

NEVER operate the watercraft after con-

suming alcohol or taking other drugs.

●

For reasons of safety and proper care of

the watercraft, always perform the pre-

operation checks listed on page 3-5

before operating the watercraft.

●

The operator and passengers should

always keep both feet in the footwell when

the watercraft is in motion. Lifting your

feet increases your chances of losing your

balance, and your feet being hit by objects

outside the watercraft. Do not give a ride

to children if their feet cannot reach the

floor of the footwell.

●

Passengers should firmly hold on to the

person in front of them.

●

Always consult your doctor on whether it

is safe for you to ride this watercraft if you

are pregnant or in poor health.

1-12

●

Do not attempt to modify this watercraft!

Modifications to your watercraft may

reduce safety and reliability, and render

the watercraft unsafe or illegal for use.

●

Attach the engine shut-off cord (lanyard)

to wrist and keep it free from the handle-

bars so that the engine stops if the opera-

tor falls off. After riding, remove the

engine shut-off cord from the watercraft to

avoid accidental starting or unauthorized

use by children or others.

●

Scan carefully for swimmers and stay

away from swimming areas. Swimmers

are hard to see and you could acciden-

tally hit someone in the water.

●

Avoid being hit by another boat! You

should always take the responsibility to

watch for traffic; other boaters may not be

watching for you. If they do not see you,

or you maneuver more quickly than other

boaters expect, you risk a collision.

●

Maintain a safe distance from other boats

or watercraft, and also watch for boats’ ski

ropes or fishing lines. Obey the “Rules of

the Road,” and be sure to check behind

you before making a turn. (See Rules of

the Road on pages 1-16 to 1-19.)

●

This watercraft is included in the Class A

inboard boat classification of the U.S.

Coast Guard. A watercraft of this type

MUST carry a fire extinguisher of a B-1

classification, with a capacity of two

pounds or more when navigating in

waters under Coast Guard jurisdiction. In

addition, most state and local boating

laws also require that the fire extinguisher

be approved by the USCG.

EJU01381

Recommended equipment

The following items should be carried on

board your watercraft:

●

Sound-signaling device

You should carry a whistle or other sound-

signaling device that can be used to sig-

nal other boats. See Rules of the Road for

more information.

●

Visual distress signals

It is recommended that a USCG approved

pyrotechnic device be stored in a water-

proof container on your watercraft. A mir-

ror can also be used as an emergency

signal. Contact your Yamaha dealer or the

Coast Guard for more information.

●

Watch

A watch is helpful so you will know how

long you have been operating.

●

Towline

A towline can be used to tow a disabled

watercraft in an emergency.

F0P03010

1-13

EJU01202

Hazard information

●

When transporting or storing your water-

craft, always place the fuel cock knob in

the “OFF” position, otherwise gasoline

may overflow from the carburetor.

●

Never start the engine or let it run for any

length of time in an enclosed area.

Exhaust fumes contain carbon monoxide,

a colorless, odorless gas that may cause

loss of consciousness and death within a

short time. Always operate the watercraft

in an open area.

●

Do not start engine on land until everyone

is away from stern. Hot water and steam

spurting from exhaust outlet can cause

serious burns.

●

Hot muffler surfaces can cause serious

burns. Do not touch any muffler surface

during or after engine operation. Catalytic

converter gets hotter after engine stops.

EJU01847

Watercraft characteristics

●

Jet thrust turns the watercraft. Releasing

the throttle completely produces only min-

imum thrust. If you are traveling at speeds

above trolling, you will have rapidly

decreasing ability to steer without throttle.

You may still have some turning ability

immediately after releasing the throttle,

but once the engine slows down, the

watercraft will no longer respond to han-

dlebar input until you open the throttle

again or you reach a trolling speed. Prac-

tice turning in an open area without

obstructions until you have a good feel for

this maneuver.

●

This watercraft is water-jet propelled. The

jet pump is directly connected to the

engine. This means that jet thrust will pro-

duce some movement whenever the

engine is running. There is no “neutral”

position. You are in either “forward” or

“reverse,” depending upon the shift lever

position.

●

Do not use the reverse function to slow

down or stop the watercraft as it could

cause you to lose control, be ejected, or

impact the handlebars.

This could increase the risk of back/spinal

injury (paralysis), facial injuries, and bro-

ken legs, ankles, and other bones. You

could also damage the shift mechanism.

1-14

●

Reverse can be used to slow down or

stop during slow speed maneuvering,

such as when docking. Once the engine

is idling, shift to reverse and gradually

increase engine speed. Make sure that

there are no obstacles or people behind

you before shifting into reverse.

●

Keep away from intake grate 1 while the

engine is on. Items such as long hair,

loose clothing, or PFD straps can become

entangled in moving parts resulting in

severe injury or drowning.

●

Never insert any object into the jet thrust

nozzle 2 while the engine is running.

Severe injury or death could result from

coming in contact with the rotating parts

of the jet pump.

●

Stop the engine and remove the clip 3

from the engine shut-off switch 4 before

removing any debris or weeds, which may

have collected around the jet intake.

EJU01899

Water-skiing

You can use the watercraft for water-ski-

ing if it has the seating capacity to carry the

operator, a rearward-facing spotter, and the

water-skier when he or she is not skiing.

The watercraft must also have a cleat 1

designed to pull a ski tow rope; do not attach

the tow rope to any other location.

It is the watercraft operator’s responsibility

to be alert to the safety of the water-skier

and others. Know and follow all state and

local water-skiing regulations in effect for the

waters in which you will be operating.

The operator should be comfortable car-

rying passengers before attempting to pull a

skier.

The following are some important consid-

erations for minimizing risks while water-ski-

ing.

●

The skier should wear an approved PFD,

preferably a brightly colored one so boat

operators can see the skier.

●

The skier should wear protective clothing.

Severe internal injuries can occur if water

is forced into body cavities as a result of

falling into the water. Normal swimwear

does not adequately protect against

forceful water entry into rectum or vagina.

The skier should wear a wetsuit bottom or

clothing that provides equivalent protec-

tion.

1-15

●

A second person should be on board as a

spotter to watch the skier; in most states it

is required by law. Let the skier direct the

operator’s control of speed and direction

with hand signals.

The spotter should sit securely on the

passenger seat and hold onto the hand-

grip 2 with feet firmly on the footrest 3

for proper balance while facing to the rear

to watch the skier’s hand signals and his

or her condition.

●

Your control while pulling a skier is

affected by the skier’s ability, as well as

water and weather conditions.

●

When preparing to pull a skier, operate

the watercraft at the slowest possible

speed until the watercraft is well away

from the skier and slack in the towrope is

taken up. Make sure that the rope is not

looped around anything.

After checking that the skier is ready and

that there is no traffic or other obstacles,

apply enough throttle to raise the skier.

●

Make smooth, wide turns. The watercraft

is capable of very sharp turns, which

could exceed the abilities of the skier.

Keep the skier at least 50 m (150 ft),

about twice the distance of a standard

towrope, from any potential hazard.

●

Be alert to the hazard of the towrope han-

dle snapping back at the watercraft when

the skier falls or is unable to get up on the

skis.

●

Towing heavy or bulky objects other than

skiers, such as another boat or watercraft,

can cause loss of steering control and

create a hazardous condition. If you must

tow another boat in an emergency situa-

tion, operate slowly and cautiously.

1-16

EJU01180

Rules of the Road

Yamaha watercraft is legally consid-

ered a powerboat. Operation of the

watercraft must be in accordance with

the rules and regulations governing the

waterway on which it is used.

Just as there are rules that apply when

you are driving on streets and highways,

there are waterway rules that apply when

you are operating your watercraft. These

rules are used internationally, and are also

enforced by the United States Coast Guard

and local agencies. You should be aware of

these rules, and follow them whenever you

encounter another vessel on the water.

Several sets of rules prevail according to

geographic location, but are all basically the

same as the International Rules of the

Road. The rules presented here in this

Owner’s/Operator’s Manual are condensed,

and have been provided for your conve-

nience only. Consult your local U.S. Coast

Guard Auxiliary or Department of Motor

Vehicles for a complete set of rules govern-

ing the waters in which you will be operating

your watercraft.

Steering and sailing rules

Whenever two vessels on the water meet

one another, one vessel has the right-of-

way; it is called the “stand-on” vessel. The

vessel that does not have the right-of-way is

called the “give-way” or “burdened” vessel.

These rules determine which vessel has the

right-of-way, and what each vessel should

do.

Stand-on vessel

The vessel with the right-of-way has the

duty to continue its course and speed,

except to avoid an immediate collision.

When you maintain your direction and

speed, the other vessel will be able to deter-

mine how best to avoid you.

Give-way vessel

The vessel which does not have the right-

of-way has the duty to take positive and

timely action to stay out of the way of the

stand-on vessel. Normally, you should not

cross in front of the vessel with the right-of-

way. You should slow down or change direc-

tions briefly and pass behind the other ves-

sel. You should always move in such a way

that the operator of the other vessel can see

what you are doing.

The General Prudential Rule regarding

the right-of-way is that if a collision appears

unavoidable, neither boat has the right-of-

way. Both boats must avoid the collision.

In other words, follow the standard rules

except when a collision will occur unless

both vessels try to avoid each other. If that is

the case, both vessels become give-way

vessels.

1-17

Rules when encountering

vessels

There are three main situations that you

may encounter with other vessels which

could lead to a collision unless the Steering

Rules are followed:

Meeting: you are approaching another

vessel head-on

Crossing: you are traveling across

another vessel’s path

Overtaking: you are passing or being

passed by another vessel

In the following illustration, your watercraft

is in the center. You should give the right-of-

way to any vessels shown in the white area

(you are the give-way vessel). Any vessels

in the shaded area must yield to you (they

are the give-way vessels). Both you and the

meeting vessel must alter course to avoid

each other.

Meeting

If you are meeting another power vessel

head on, and are close enough to run the

risk of collision, neither of you has the right-

of-way! Both of you should alter course to

avoid an accident. You should keep the

other vessel on your port (left) side. This

rule does not apply if both of you will clear

one another if you continue on your set

course and speed.

Crossing

When two power-driven vessels are

crossing each other’s path close enough to

run the risk of collision, the vessel which has

the other on the starboard (right) side must

keep out of the way of the other. If the other

vessel is on your starboard (right) side, you

must keep out of its way; you are the give-

way vessel. If the other vessel is on your

port (left) side, remember that you should

maintain course and direction, provided the

other vessel gives you the right-of-way as it

should.

1-18

Overtaking

If you are passing another vessel, you are

the give-way vessel. This means that the

other vessel is expected to maintain its

course and speed. You must stay out of its

way until you are clear of it. Likewise, if

another vessel is passing you, you should

maintain your speed and direction so that

the other vessel can steer itself around you.

Other special situations

There are three other rules you should be

aware of when riding your watercraft around

other vessels.

Narrow channels and bends

When navigating in narrow channels, you

should keep to the right when it is safe and

practical to do so. If the operator of a power-

driven vessel is preparing to go around a

bend that may obstruct the view of other

water vessels, the operator should sound a

prolonged blast of four to six seconds on the

whistle. If another vessel is around the bend,

it too should sound the whistle. Even if no

reply is heard, however, the vessel should

still proceed around the bend with caution. If

you navigate such waters with your water-

craft, you will need to carry a portable air

horn, available from local marine supply

stores.

Fishing vessel right-of-way

All vessels fishing with nets, lines or

trawls are considered to be “fishing vessels”

under the International Rules. Vessels with

trolling lines are not considered fishing ves-

sels. Fishing vessels have the right-of-way

regardless of position. Fishing vessels can-

not, however, impede the passage of other

vessels in narrow channels.

Sailing vessel right-of-way

Sailing vessels should normally be given

the right-of-way. The exceptions to this are:

1. When the sailing vessel is overtaking the

power-driven vessel, the power-driven

vessel has the right-of-way.

2. Sailing vessels should keep clear of any

fishing vessel.

3. In a narrow channel, a sailing vessel

should not hamper the safe passage of a

power-driven vessel that can navigate

only in such a channel.

Reading buoys and other

markers

The waters of the United States are

marked for safe navigation by the lateral

system of buoyage. Simply put, buoys and

markers have an arrangement of shapes,

colors, numbers and lights to show which

side of the buoy a boater should pass on

when navigating in a particular direction.

The markings on these buoys are oriented

from the perspective of being entered from

seaward (the boater is going towards the

harbor). Red buoys are passed on your star-

board (right) side when proceeding from

open water into the harbor, and black buoys

are to your port (left) side. An easy way to

remember the meaning of the colors is the

phrase “red right returning.” When navigat-

ing out of the harbor, your position with

respect to the buoys should be reversed; red

buoys should be to port and black buoys to

starboard.

Many bodies of water used by boaters are

entirely within the boundaries of a particular

state. The Uniform State Waterway Marking

System has been devised for these waters.

1-19

This system uses buoys and signs with

distinctive shapes and colors to show regu-

latory or advisory information. These mark-

ers are white with black letters and orange

borders. They signify speed zones,

restricted areas, danger areas, and general

information.

Remember, markings may vary by geo-

graphic location. Always consult local boat-

ing authorities before riding your watercraft

in unfamiliar waters.

1-20

EJU01181

To get more boating

safety information

Be informed about boating safety. Addi-

tional publications and information can be

obtained from many organizations, including

the following.

United States Coast Guard

Consumer Affairs Staff (G-BC)

Office of Boating, Public, and Consumer

Affairs

U.S. Coast Guard Headquarters

Washington, D.C. 20593-0001

Boating Safety Hotline: 1-800-368-5647

Other sources

You can find local rules by contacting the

National Association of State Boating Law

Administrators, or your local Power Squad-

ron.

Watercraft Education and

Training

The Online Boating Safety Course, avail-

able through the watercraft section of the

yamaha-motor.com website, is a free,

50 question learning course available to the

public. Upon successful completion of

80 percent or better, the user can request a

certificate of completion by mail or can

download one immediately. The Online

Boating Safety Course, provided by the

Boat/US Foundation, is approved by the

National Association of State Boating Law

Administrators (NASBLA) and recognized

by the United States Coast Guard. This

course meets the education requirement for

those states that recognize non-proctored,

NASBLA-approved courses.

Yamaha is the watercraft industry’s lead-

ing manufacturer to build awareness and

support for boating education. In 1997,

Yamaha launched its GET W.E.T. (Water-

craft Education and Training) initiative and

has since reached out to over one million

Americans promoting the benefits of boating

education.

The Online Boating Safety Course:

http://www.boatus.com/onlinecourse/

1-21

EJU01006

Enjoy your watercraft

responsibly

You share the areas you enjoy when

riding your watercraft with others and with

nature. So your enjoyment includes a

responsibility to treat these other people,

and the lands, waters, and wildlife with

respect and courtesy.

Whenever and wherever you ride, think of

yourself as the guest of those around you.

Remember, for example, that the sound of

your watercraft may be music to you, but it

could be just noise to others. And the excit-

ing splash of your wake can make waves

others won’t enjoy. Avoid riding close to

shoreline homes and waterfowl nesting

areas or other wildlife areas, and keep a

respectful distance from fishermen, other

boats, swimmers, and populated beaches.

When travel in areas like these is unavoid-

able, ride slowly and obey all laws.

Remember that pollution can be harmful

to the environment. Do not refuel or add oil

where a spill could cause damage to nature.

Remove your watercraft from the water and

move it away from the shoreline before refu-

eling. And keep your surroundings pleasant

for the people and wildlife that share the

waterways: don’t litter!

When you ride responsibly, with respect

and courtesy for others, you help ensure

that our waterways stay open for the enjoy-

ment of a variety of recreational opportuni-

ties.

EJU01007

FEATURES AND

FUNCTIONS

Location of main components

..............2-1

Operation of controls and other

functions

...................................................2-5

Rear seat ................................................2-5

Front seat ...............................................2-6

Hood .......................................................2-7

Fuel tank filler cap ..................................2-8

Oil tank filler cap .....................................2-8

Fuel cock knob .......................................2-9

Engine stop switch ...............................2-10

Engine shut-off switch ..........................2-10

Choke knob ..........................................2-10

Throttle lever ........................................2-11

Start switch ...........................................2-11

Cooling water pilot outlet .....................2-12

Steering system ...................................2-12

Tilt lever ................................................2-13

Shift lever .............................................2-14

Quick Shift Trim System (QSTS)

selector .................................................2-15

Handgrip ...............................................2-16

Engine overheat warning system ........ 2-17

Exhaust temperature warning

system ..................................................2-19

Multifunction meter ...............................2-20

PADLOC (Programmable digital

locking ignition) ....................................2-21

Tachometer ..........................................2-23

Speedometer .......................................2-24

Fuel meter ............................................2-24

Engine oil meter ...................................2-25

Clock ....................................................2-25

Hour meter ...........................................2-26

Trip timer ..............................................2-26

Tripmeter ..............................................2-27

Fuel warning indicator ..........................2-27

Oil warning indicator ............................2-28

Engine overheat warning indicator ...... 2-28

Exhaust temperature warning

indicator ................................................2-29

Battery warning indicator .....................2-29

Storage compartments ........................2-30

2-1

EJU01008

Location of main components

Handlebars

Use to control direction.

Footwell

Use to place feet for balance.

Footrest

To keep proper balance while facing to the rear

to watch the skier.

Bow eye

Use to attach rope for transporting, mooring or

towing the watercraft in an emergency.

Hood

Front seat

Rear seat

Sponsons

Gunwale

2-2

Fuel tank filler cap

Rope holes

Intake grate

Prevents debris from getting into the jet pump.

Speed sensor

Cleat

Use to attach a towrope for pulling water-skier,

or a rope for mooring the watercraft.

Handgrip

Use for support when boarding the watercraft

or when seated facing rearward and acting as

a spotter for a water-skier.

Reverse gate

Controls direction of jet thrust when in reverse.

Stern drain plugs

Use to drain water in the bilge when the water-

craft is on dry land.

Jet thrust nozzle

Changes the direction of jet thrust according

to handlebar position.

Ride plate

2-3

Engine stop switch

Push to stop the engine normally.

Clip

Insert into the engine shut-off switch to enable

starting of the engine.

Remove to stop the engine or prevent acci-

dental starting of the engine or unauthorized

use of the watercraft.

Quick Shift Trim System (QSTS) selector

Use to select the trim angle of the watercraft.

QSTS shift lock lever

Engine shut-off switch

Remove the clip to stop the engine and dis-

able it from starting.

Start switch

Push to start the engine.

Fuel cock knob

Use to select either normal or reserve fuel flow

from the fuel tank to the carburetors, or to shut

off fuel flow.

Choke knob

Use to start a cold engine.

Engine shut-off cord (lanyard)

Attach to wrist so that the engine stops if the

operator falls off the watercraft.

Adjustable rearview mirrors

Multifunction meter

Use to check watercraft operation.

Shift lever

Use to put the watercraft into forward or

reverse.

Throttle lever

Use to accelerate and decelerate.

Tilt lever

Use to adjust the tilt of the handlebars.

Glove compartment

+ 108 hidden pages

Yamaha XLT1200 User Manual

CONTENTS