3-073-156-11 (1) GB
Video Cassette
Recorder
Operating Instructions
PAL NTSC
SLV-ED929MI SLV-ED925PS SLV-ED828ME/SG SLV-ED825PS SLV-ED323ME/SG
SLV-ED225PS
© 2002 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
The mains lead must only be changed at a qualified service shop.
Precautions
Safety
•This unit operates on 110 –240 V AC, 50/ 60 Hz. Check that the unit’s operating voltage is identical with your local power supply.
•If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
•The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
•Unplug the unit from the mains if you do not intend to use it for an extended period of time. To disconnect the lead, pull it out by the plug, never by the lead.
•To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Installing
•Allow adequate air circulation to prevent internal heat buildup.
•Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
•Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
•Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
•Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
•Do not place heavy objects on the unit.
•If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about four hours before operating the unit.
Caution
Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour/TV systems
•This VCR is designed to record and play back using the PAL (B/G, D/K and I), MESECAM (B/G and D/K) and NTSC (M*) colour systems. Recording of video sources based on other colour systems cannot be guaranteed.
* SLV-ED929MI only
For SLV-ED925PS, ED828ME/SG,
ED825PS, ED323ME/SG and ED225PS
•NTSC colour signals can only be recorded through the line input.
G-CODE is a registered trade mark of Gemstar Development Corporation. The G-CODE system is manufactured under license from Gemstar Development Corporation.
2 WARNING
Table of Contents
Getting Started
4 Index to parts and controls
10Step 1 : Unpacking
11Step 2 : Setting up the remote commander
13 Step 3 : Connecting the VCR
15Step 4 : Setting up the VCR with the Auto Set Up function
18 Step 5 : Setting the clock
20Step 6 : Selecting the TV system
21Selecting a language (SLV-ED828ME/SG and ED323ME/SG only)
22Presetting channels
25Changing/disabling programme positions
Basic Operations
30 Playing a tape
32 Recording TV programmes
36Recording TV programmes using the Easy Timer
42Recording TV programmes using the G-CODE® system (SLV-ED929MI only)
45Recording TV programmes using the timer
Additional Operations
48Playing/searching at various speeds
49Setting the recording duration time
50Checking/changing/cancelling timer settings
52Recording stereo and bilingual programmes (not available on SLVED323ME/SG and ED225PS)
55Searching using the index function
56Adjusting the picture
57Reducing the VCR’s power consumption
58Changing menu options
Editing
60Connecting to a VCR or stereo system
62 Basic editing
Additional Information
63 Troubleshooting
67 Specifications
Back cover
Index
Started Getting
Table of contents 3
Refer to the pages indicated in parentheses ( ) for details.
Front panel
For SLV-ED929MI, ED925PS, ED828ME/SG and ED825PS
1?/1 ON/STANDBY switch
2Remote sensor (11)
3Tape compartment
4A EJECT button (30)
5HPLAY button*1 (30) (48)
6x STOP button*1 (17) (30) (62)
7z REC (record) button (33) (49)
(62)
8X PAUSE button (30) (41) (62)
9M FF (fast-forward) button (30)
(48)
q;m REW (rewind) button (30) (48) qaEASY TIMER (36)
qsPROGRAM/TRACKING +/– buttons*1 (37) (56)
qdLINE-2 IN VIDEO/AUDIO L/R (left/right) jacks*2 (60) (61)
*1 The H PLAY, x STOP and PROGRAM/ TRACKING + buttons have a tactile dot.
*2 not available on SLV-ED825PS
4 Getting Started
For SLV-ED323ME/SG and ED225PS
Started Getting
1?/1 ON/STANDBY switch
2A EJECT button (30)
3Remote sensor (11)
4Tape compartment
5m REW (rewind) button (30) (48)
6H PLAY button (30) (48)
7M FF (fast-forward) button (30)
(48)
8z REC (record) button (33) (49)
(62)
9x STOP button (17) (30) (62) q;X PAUSE button (30) (41) (62) qaEASY TIMER (36)
qsPROGRAM/TRACKING +/– buttons* (37) (56)
*The PROGRAM/TRACKING + button has a tactile dot.
continued
Getting Started 5
Index to parts and controls (continued)
Display window
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
|
qa |
|
|
0 |
|
|
9 |
1Tape indicator
2START indicator (37)
3STOP indicator (37)
4MONTH indicator (40)
5YEAR indicator
6NICAM indicator*1 (53)
7STEREO indicator*2 (52)
8Timer indicator (39) (43) (46)
9Recording indicator (33)
q;Time counter/clock/line/programme position indicator (31) (32) (62)
qaTape speed indicators (32) (38)
*1 SLV-ED929MI and ED925PS only
*2 not available on SLV-ED323ME/SG and ED225PS
6 Getting Started
Rear panel
For SLV-ED929MI, ED925PS, ED828ME/SG and ED825PS
1 2 |
3 |
||
|
|
|
|
|
|
|
|
54
For SLV-ED323ME/SG and ED225PS
1 2 |
3 |
||
|
|
|
|
|
|
|
|
5 4
Started Getting
1 (in from antenna) connector (13)
2LINE IN 1 AUDIO R/L/VIDEO (audio right/audio left/video) jacks*1 (61)
LINE IN 1 AUDIO/VIDEO jacks*2 (60)
3Mains lead (13)
4LINE OUT AUDIO R/L/VIDEO (audio right/audio left/video) jacks*1 LINE OUT AUDIO/VIDEO jacks*2 (14)
5 (out to tv) connector (13)
*1 SLV-ED929MI, ED925PS, ED828ME/SG and ED825PS only
*2 SLV-ED323ME/SG and ED225PS only
continued
Getting Started 7
Index to parts and controls (continued)
Remote commander |
|
1Z EJECT button (30) |
||
|
|
|
2INPUT SELECT button (32) (45) |
|
|
|
|
(62) |
|
|
|
|
3TV/VIDEO button (for TV) |
|
|
|
|
4CLEAR button (31) (42) (50) |
|
|
|
|
5Programme number buttons* (42) |
|
|
|
|
6-/-- (ten’s digit) button |
|
|
|
|
7VOL (volume) +/–buttons |
|
1 |
2 |
3 |
8z REC (record) button (33) (49) |
|
4 |
5 |
6 |
9REC SPEED (recording speed) |
|
7 |
8 |
9 |
button (32) |
|
q;MENU button (21) (50) |
||||
|
0 |
|
||
|
|
qaX PAUSE/Mbutton (21) (30) |
||
|
|
|
||
|
|
|
x STOP/mbutton (21) (30) |
|
|
|
|
m REW (rewind)/<button (21) |
|
|
|
|
(30) (48) |
|
|
|
|
M FF (fast-forward)/,button |
|
|
|
|
(21) (30) (48) |
|
|
|
|
HPLAY/OK button* (21) (30) |
|
|
|
|
(48) |
|
|
|
|
* The H PLAY, AUDIO MONITOR, |
|
|
|
|
number 5 and PROG + buttons have a |
|
|
|
|
tactile dot. |
8 Getting Started
qs?/1 (on/standby) switch (43)
qd•TV/VIDEO remote control switch (11)
qfAUDIO MONITOR button*1*2 (52) qgG-CODE button*3 (42)
qhDISPLAY button (31) (33)
qjPROG (programme) +/–buttons*1 (34)
1 |
2 |
3 |
qky SLOW button (48) |
|
4 |
5 |
6 |
ql× 2 button (48) |
|
7 |
8 |
9 |
w;./> INDEX SEARCH |
|
buttons (55) |
||||
|
|
|
||
|
0 |
|
|
|
|
|
|
*1 The HPLAY, AUDIO MONITOR, |
|
|
|
|
number 5 and PROG + buttons have a |
|
|
|
|
tactile dot. |
|
|
|
|
*2 not available on SLV-ED323ME/SG and |
|
|
|
|
ED225PS |
|
|
|
|
*3 SLV-ED929MI only |
Started Getting
Getting Started 9
Check that you have received the following items with the VCR:
• Remote commander |
• Aerial cable |
• R6 (size AA) batteries |
• Plug adaptor (SLV-ED828ME and |
|
ED323ME only) |
Check your model name
The instructions in this manual are for the 8 models: SLV-ED929MI, ED925PS, ED828ME/SG, ED825PS, ED323ME/SG and ED225PS. Check your model name by looking at the rear panel of your VCR. SLV-ED929MI is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “ SLV-ED929MI only.”
10 Getting Started
Inserting the batteries
Insert two R6 (size AA) batteries by matching the + and –on the batteries to the diagram inside the battery compartment.
Insert the negative (–)end first, then push in and down until the positive (+) end clicks into position.
Using the remote commander
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV.
Remote sensor
•TV/VIDEO
1 2 3
4 5 6
7 8 9
0
Started Getting
To operate |
Set •TV/VIDEO to |
||||||
|
|
|
|
|
|
||
the VCR |
VIDEO and point at the remote sensor at the VCR |
||||||
|
|
|
|
||||
a Sony TV |
•TV and point at the remote sensor at the TV |
||||||
|
|
|
|
|
|
||
|
|
|
|
continued |
|||
|
|
|
Getting Started |
|
11 |
||
|
|
||||||
|
|
|
|
|
|
|
|
Step 2 : Setting up the remote commander (continued)
Notes
•With normal use, the batteries should last about three to six months.
•If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
•Do not use a new battery together with an old one.
•Do not use different types of batteries together.
•Some buttons may not work with certain Sony TVs.
12 Getting Started
Connect the aerial to your VCR and TV as shown below to watch TV programmes and VCR pictures on your TV. In addition, if your TV has audio/video (A/V) input jacks, we recommend you connect the VCR to your TV using an audio/video cable to get a better picture and sound.
Connecting the aerial
Started Getting
Mains lead
AERIAL IN to mains
Aerial cable (supplied)
: Signal flow
1
2
3
Disconnect the aerial cable from your TV and connect it to on the rear panel of the VCR.
Connect of the VCR and the aerial input of your TV using the supplied aerial cable.
Connect the mains lead to the mains.
Note
•When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 15).
continued
Getting Started 13
Step 3 : Connecting the VCR (continued)
Additional connections
To a TV that has audio/ video input jacks
This additional connection improves picture and sound quality. Connect the TV as shown on the right.
For SLV-ED929MI, ED925PS, ED828ME/SG
and ED825PS
LINE OUT
LINE IN
Audio/video cable (not supplied)
For SLV-ED323ME/SG and ED225PS
LINE OUT
LINE IN
To a stereo system (not available on SLVED323ME/SG and ED225PS)
You can improve sound quality by connecting a stereo system to the LINE OUT AUDIO R/L jacks as shown on the right.
Note
Audio/video cable (not supplied)
LINE OUT |
|
AUDIO R/L |
LINE IN |
Audio cable (not supplied) |
|
•To play a tape in stereo, you must connect your VCR either to a TV with audio/ video input jacks or to a stereo system as shown on above right.
14 Getting Started
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display and TV channels automatically.
Started Getting
1
2
Turn on your TV and set it to the video channel.
Tune the TV to channel 51 (for SLV-ED929MI, ED925PS, ED825PS and ED225PS) or 32 (for SLV-ED828ME/SG and ED323ME/SG) (the initial RF channel for this VCR). Refer to your TV manual for TV tuning instructions. If the picture does not appear clearly, see “ To change the RF channel” on page 17.
Connect the mains lead to the mains.
PLAY |
The VCR automatically turns on. |
|
|
OK |
|
For SLV-ED929MI, ED925PS, ED825PS and ED225PS
The message for the Auto Set Up function appears on the TV screen.
For SLV-ED828ME/SG and ED323ME/SG
The LANGUAGE SET menu appears on the TV screen.
Press </,to select the desired language, ENGLISH or ARABIC, then press OK.
|
|
|
|
|
|
ENGLISH |
|
ARABIC |
|
|
SELECT : |
|
||
|
SET |
: OK |
EXIT : MENU |
The message for the Auto Set Up function appears.
continued
Getting Started 15
Step 4 : Setting up the VCR with the Auto Set Up function (continued)
3
PLAY
OK
Press OK.
The SYSTEM SELECT menu appears.
For SLV-ED929MI
SYSTEM SELECT
SYSTEM–B/G |
SYSTEM–D/K |
SYSTEM–I |
SYSTEM–B/B |
U.S–ANT. |
U.S–HRC |
U.S–IRC |
JAPAN |
SELECT : |
|
EXECUTE : OK |
END : MENU |
For SLV-ED925PS, ED828ME/SG,
ED825PS, ED323ME/SG and
ED225PS
SYSTEM SELECT
SYSTEM – B/G
SYSTEM – D/K
SYSTEM – I
SELECT |
: |
|
SET |
: OK |
EXIT : MENU |
4
PLAY
OK
Press M/m/</,to select the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
appropriate TV system, then press |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OK. |
|
|
|
|
|
|
|
|
|
|
AUTO SET UP |
||||||||||||||||||||||||||||||||||
The VCR starts searching for all of |
|
|
|
|
|
|
|
|
|
|
PLEASE WAIT |
||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
the receivable channels and presets |
4 0 % |
||||||||||||||||||||||||||||||||||||||||||||
them (in the appropriate order for |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
your local area). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
EXIT : MENU |
||||||||||||||||||
If you want to change the order of |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
the channels or disable unwanted |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
programme positions, see |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
“ Changing/disabling programme |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
positions” on page 25. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After the search is complete, the clock setting menu appears. See “ Setting the clock” on page 18.
16 Getting Started
To cancel the Auto Set Up function
Press MENU.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on the VCR and TV. Select INSTALLATION from the menu, then press M/m to highlight VCR OUTPUT CH and press ,. Select the RF channel by pressing the M/mbuttons. Then, tune the TV to the new RF channel so that a clear picture appears.
Tip
•If you want to change the language for the on-screen display from the one preset in the Auto Set Up function, see page 21.*
Notes
•Whenever you operate the Auto Set Up function, some of the settings (timer, etc.) will be reset. If this happens, you have to set them again.
•Auto preset starts automatically only when you plug in the mains lead for the first time after you purchase the VCR.
•After using the Auto Set Up function, the LANGUAGE SET menu* does not appear automatically when you connect the mains lead again. If you want to use the Auto Set Up function again, press MENU, then press M/m/</,to highlight INSTALLATION and press OK. Press M/mto highlight AUTO SET UP, then repeat all procedures from step 3.
•Auto preset can be performed by pressing x STOP on the VCR continuously for 5 seconds or more with no tape inserted.
* SLV-ED828ME/SG and ED323ME/SG only
Started Getting
Getting Started 17
You must set the time and date on the VCR to use the timer features properly.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “ Index to parts and controls” for button locations.
1 MENU
PLAY
OK
Press MENU, then press M/m/</ ,to highlight CLOCK SET and press OK.
|
|
|
|
|
|
|
1 2 : 0 0 |
1 / JAN / 2 0 0 2 |
|
||
|
|
|
|
TUE |
|
|
SELECT : |
SET |
: |
|
|
|
END |
: OK |
EXIT |
: MENU |
2 |
Press M/mto set the hour. |
|
|
|
PLAY |
|
|
|
OK |
|
1 / JAN / 2 0 0 2 |
|
1 8 : 0 0 |
||
|
|
|
TUE |
|
SELECT : |
SET : |
|
|
END |
: OK |
EXIT : MENU |
3
PLAY
OK
Press ,to select the minutes and set the minutes by pressing M/m.
1 8 : 3 0 |
1 / JAN / 2 0 0 2 |
||
|
|
|
TUE |
SELECT : |
SET |
: |
|
END |
: OK |
EXIT |
: MENU |
18 Getting Started
4
5
PLAY
OK
Set the day, month, and year in sequence by pressing ,to select the item to be set, and press M/mto select the digits, then press ,.
The day of the week is set automatically.
|
|
|
|
|
|
|
|
1 8 : 3 0 |
2 8 / SEP / 2 0 0 2 |
|
|||
|
|
|
|
|
SAT |
|
|
SELECT : |
|
SET |
: |
|
|
|
END |
: OK |
EXIT |
: MENU |
MENU |
Press MENU to exit the menu. |
|
Tip
•To change the digits while setting, press < to return to the item to be changed, and select the digits by pressing M/m.
Started Getting
Getting Started 19
You must select the appropriate TV system for your area.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “ Index to parts and controls” for button locations.
1 MENU
PLAY
OK
Press MENU, then press M/m/</ ,to highlight INSTALLATION and press OK.
|
|
|
|
|
|
|
AUTO SET UP |
|
|
|
|
|
MANUAL SET UP |
|
|
|
|
|
TV SYSTEM |
: G |
|
|
|
|
VCR OUTPUT CH |
: 3 2 |
|
||
|
SELECT : |
SET |
: |
|
|
|
END |
: OK |
EXIT |
: MENU |
2
PLAY
OK
Press M/mto highlight TV
SYSTEM, then press ,.
AUTO SET UP |
|
|
|
MANUAL SET UP |
|
|
|
TV SYSTEM |
: G |
|
|
VCR OUTPUT CH |
: 3 2 |
||
SELECT |
: |
SET |
: |
END |
: OK |
EXIT |
: MENU |
3
PLAY
OK
Press ,to select the appropriate TV system.
Select |
For |
G |
the B/G TV system |
|
|
K |
the D/K TV system |
|
|
I |
the I TV system |
|
|
B* |
the B/B TV system |
|
|
M* |
the U.S–ANT., U.S–HRC, U.S–IRC and JAPAN TV |
|
systems |
|
|
4 |
MENU |
Press MENU to exit the menu. |
|
* SLV-ED929MI only
20 Getting Started
Selecting a language (SLV-ED828ME/SG
and ED323ME/SG only)
You can change the on-screen display language from the one you selected with the Auto Set Up function.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “ Index to parts and controls” for button locations.
1 MENU
PLAY
OK
Press MENU, then press M/m/</ ,to highlight LANGUAGE SET and press OK.
|
|
|
|
|
|
ENGLISH |
|
ARABIC |
|
|
SELECT : |
|
||
|
SET |
: OK |
EXIT : MENU |
2 |
|
Press </,to highlight the desired language, ENGLISH or |
|
PLAY |
ARABIC, then press OK. |
OK
Started Getting
Getting Started 21