KDC-X700
KDC-BT765HD
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X700/ KDC-BT765HD Serial number
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
© 2015 JVC KENWOOD Corporation |
B5A-0889-00 (KW) |
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
i
IC (Industry Canada) Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)This device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1)l’appareil ne doit pas produire de brouillage, et
(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.
Para cumplimiento de la COFETEL:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1)es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2)este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada”
Contains Bluetooth Module |
FCC ID: |
ZWY8350X |
|
IC ID: |
12033A-8350X |
|
|
|
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
ii
SOFTWARE LICENSE AGREEMENT
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.
The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.
Article 1 General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")
Article 2 |
License |
1.The license granted under this Agreement shall be the right to use the Licensed Software in the Product.
2.The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.
3.The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4.The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 3 Conditions for Grant of License
1.When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.
2.The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.
Article 4 Right pertaining to the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Article 5 Indemnification of Licensor
1.Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.
2.The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.
Article 6 Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.
Article 7 Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.
iii
Article 8 |
Termination |
|
|
In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event:
(1)when the User violated any provision of this Agreement; or
(2)when a petition has been filed against the User for an attachment,
provisional attachment, provisional disposition or any other compulsory execution.
Article 9 Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.
Article 10 Protection of Copyright
1.The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.
2.The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.
Article 11 Export Restriction
1.It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).
2.The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.
3.The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).
Article 12 Miscellaneous
1.In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.
2.Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.
3.The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.
Important Notice concerning the Software
-jansson
Copyright (c) 2009-2012 Petri Lehtinen <petri@digip.org>
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
iv
CONTENTS
BEFORE USE |
2 |
BASICS |
3 |
|
|
GETTING STARTED |
4 |
1Select the display language and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
HD RadioTM tuner |
5 |
CD / USB / iPod / ANDROID |
7 |
|
|
AUX |
9 |
|
|
Pandora® |
10 |
|
|
iHeartRadio® |
11 |
|
|
SiriusXM® Radio |
12 |
|
|
BLUETOOTH® |
15 |
|
|
AUDIO SETTINGS |
21 |
|
|
DISPLAY SETTINGS |
23 |
|
|
REFERENCES |
24 |
Maintenance |
|
More information |
|
|
|
TROUBLESHOOTING |
27 |
|
|
INSTALLATION / |
|
CONNECTION |
30 |
|
|
SPECIFICATIONS |
32 |
BEFORE USE
IMPORTANT
•To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.
•Please keep the manual in a safe and accessible place for future reference.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
•Adjust the volume so that you can hear sounds outside the car to prevent accidents.
•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•Avoid using the external device if it might hinder safe driving.
•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
•Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
•If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
•USB rating is indicated on the main unit. To view, detach the faceplate. ( 3)
•Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the
antenna control wire connected ( 31). Turn off the unit or change the source to STANDBY when parking at a low ceiling area.
Remote control (RC-406):
•Do not leave the remote control in hot places such as on the dashboard.
•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
•Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
How to read this manual
•Operations are explained mainly using buttons on the faceplate of .
•English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. ( 5)
•[XX] indicates the selected items.
•( XX) indicates references are available on the stated page.
2
BASICS
Faceplate
Volume knob |
Display window |
Detach button
Attach |
Detach |
How to reset |
Press the switch twice within 5 seconds after detaching the faceplate.
Remote control (RC-406)
Remote sensor (Do not expose to bright sunlight.)
Pull out the insulation sheet when using for the first time.
How to replace the battery |
To |
On the faceplate |
On the remote control |
|
||
Turn on the power |
Press |
. |
Press and hold SRC to turn off the power. |
||
|
• Press and hold to turn off the power. |
( Pressing SRC does not turn on the power. ) |
|||
|
|
|
|
|
|
Adjust the volume |
Turn the volume knob. |
Press |
or |
. |
|
|
|
|
|
||
|
|
|
Press ATT during playback to attenuate the sound. |
||
|
|
|
• Press again to cancel. |
|
|
|
|
|
|
|
|
Select a source |
Press |
repeatedly. |
Press SRC repeatedly. |
|
|
|
|
|
|
||
Change the display information |
Press DISP repeatedly. ( 26) |
( Not available ) |
|
||
|
|
|
|
|
|
ENGLISH 3
GETTING STARTED
1Select the display language and cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME KNOB”
1Turn the volume knob to select [ENG] (English) or [SPA] (Spanish), then press the knob.
[ENG] is selected for the initial setup.
Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”.
2Press the volume knob.
[YES] is selected for the initial setup.
3Press the volume knob again.
“DEMO OFF” appears.
2Set the clock and date
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [CLOCK], then press the knob.
To adjust the clock
3 Turn the volume knob to select [CLOCK ADJUST], then press the knob.
4Turn the volume knob to make the settings, then press the knob.
Hour Minute
5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob.
To set the date
7 Turn the volume knob to select [DATE FORMAT], then press the knob.
8Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press the knob.
9 Turn the volume knob to select [DATE SET], then press the knob.
10Turn the volume knob to make the settings, then press the knob.
Day Month Year or Month Day Year
11Press and hold to exit.
To return to the previous setting item, press .
3Set the initial settings
1 |
Press |
repeatedly to enter STANDBY. |
2 |
Press the volume knob to enter [FUNCTION]. |
3Turn the volume knob to select an item (see the following table), then press the knob.
4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.
To return to the previous setting item, press .
Default: XX
DISPLAY
|
EASY MENU |
When entering [FUNCTION]... |
|
|
ON: ZONE1 and ZONE2 illuminations change to white color. ; OFF: ZONE1 |
|
|
and ZONE2 illuminations remain as [COLOR SELECT] colors. ( 24) |
|
|
(Refer to the illustration on page 23 for zone identification.) |
|
|
|
TUNER SETTING |
|
|
|
PRESET TYPE |
NORMAL: Memorizes one station for each preset button in each band |
|
|
(FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel |
|
|
for each preset button, regardless of the selected band or SiriusXM |
|
|
channel. |
4
GETTING STARTED
SYSTEM
|
KEY BEEP |
ON: Activates the keypress tone. ; OFF: Deactivates. |
||
|
|
|
|
|
|
SOURCE SELECT |
|
||
|
|
PANDORA SRC |
ON: Enables PANDORA in source selection. ; OFF: Disables. ( 10) |
|
|
|
|
|
|
|
|
IHEART SRC |
ON: Enables IHEARTRADIO in source selection. ; OFF: Disables. ( 11) |
|
|
|
|
|
|
|
|
BUILT-IN AUX |
ON: Enables AUX in source selection. ; OFF: Disables. ( 9) |
|
|
|
|
|
|
|
CD READ |
1: Automatically distinguishes between audio file disc and music CD. ; |
||
|
|
|
|
2: Forces to play as a music CD. No sound can be heard if an audio file disc is |
|
|
|
|
played. |
|
F/W UPDATE |
|
||
|
|
|
|
|
|
|
UPDATE SYSTEM/ UPDATE HD |
||
|
|
|
F/W UP xx.xx |
YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not |
|
|
|
|
activated). |
|
|
|
|
For details on how to update the firmware, see: www.kenwood.com/cs/ce/ |
|
|
|
|
|
|
FACTORY RESET |
YES: Resets the settings to default (except the stored station). ; NO: Cancels. |
||
|
|
|
|
|
CLOCK |
|
|||
|
|
|
|
|
|
CLOCK DISPLAY |
ON: The clock time is shown on the display even when the unit is turned off. ; |
||
|
|
|
|
OFF: Cancels. |
|
|
|
|
|
ENGLISH |
Select the display language for [FUNCTION] menu and music information if |
|||
|
|
|
|
applicable. |
|
|
|
|
ESPANOL |
By default, [ENGLISH] is selected. |
|
HD Radio™ tuner
You can tune in to both conventional and HD Radio broadcasts.
•To find HD Radio stations in your area, visit <http://www.hdradio.com>.
Search for a station
1 Press repeatedly to select HD RADIO.
2Press repeatedly (or press / on RC-406) to select FM1/ FM2/ FM3/ AM.
3Press S / T (or press S / on RC-406) to search for a station or channel.
•To change the searching method for S / T: Press repeatedly.
AUTO1 : Automatically search for a station or channel. AUTO2 : Search for a preset station or channel. MANUAL : Manually search for a station or channel.
•To store a station or channel: Press and hold one of the number buttons (1 to 6).
•To select a stored station or channel: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).
ENGLISH 5
HD Radio™ tuner
Direct Access Tuning (using RC-406)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press to search for a station or channel.
•To cancel, press or DIRECT.
•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.
Select an HD Radio multicast channel
Many HD Radio stations offer more than one channel programming. This service is called multicasting. While receiving HD Radio multicast channels....
Press S / T to select your desired channel (HD1 to HD8).
“LINKING” appears while linking to a multicast channel.
Other settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select an item (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.
To return to the previous setting item, press .
|
|
Default: XX |
TUNER SETTING |
|
|
|
|
|
|
IF BAND |
AUTO: Increases the tuner selectivity to reduce interference noises from |
|
|
adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to |
|
|
interference noises from adjacent FM stations, but sound quality will not |
|
|
be degraded and the stereo effect will remain. |
|
|
|
|
AUTO MEMORY |
YES: Automatically starts memorizing 6 stations with good reception. ; |
|
|
NO: Cancels. |
|
|
• Selectable only if [NORMAL] is selected for [PRESET TYPE]. ( 4) |
|
|
|
|
RECEIVE MODE |
Sets the receive mode of the HD Radio receiver. |
|
|
AUTO: Automatically tunes to analog broadcast when there is no |
|
|
digital broadcast. ; DIGITAL: Tunes in to digital broadcast only. ; |
|
|
ANALOG: Tunes in to analog broadcast only. |
|
|
|
CLOCK |
|
|
|
|
|
|
TIME SYNC |
ON: Synchronizes the unit’s time to the Radio Broadcast Data System |
|
|
station time. ; OFF: Cancels. |
|
|
|
6
CD / USB / iPod / ANDROID
Start playback
The source changes automatically and playback starts.
|
|
|
|
Label side |
MEject disc |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
USB input terminal
USB
CA-U1EX (max.: 500 mA) (optional accessory)
iPod/iPhone
KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2
ANDROID*3
Micro USB 2.0 cable*2 (commercially available)
*1 |
|
|
|
|
|
|
|
|
|
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type |
||||
*2 |
Do not leave the cable inside the car when not using. |
To |
|
On the faceplate |
|
|
On the remote control |
|
|||
Playback / pause |
Press |
. |
|
|
Press |
|
. |
|
|
|
|
|
|
|
|||||
Reverse / |
Press and hold S / T. |
|
Press and hold S / |
. |
|||||
Fast-forward*4 |
|
|
|
|
|
|
|
|
|
Select a track/file |
Press S / T. |
|
|
Press S / |
|
. |
|
||
|
|
|
|
|
|
|
|
||
Select a folder*5 |
Press J / K. |
|
|
Press |
/ |
|
. |
||
Repeat play*6 |
Press |
repeatedly. |
|
|
|
|
|
||
|
|
TRACK REPEAT/ ALL REPEAT |
|
: Audio CD |
|
|
|||
|
|
FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT : MP3/WMA/AAC/WAV/FLAC |
|||||||
|
|
|
|
|
|
file |
|
|
|
|
|
FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF : iPod or ANDROID |
|
||||||
|
|
|
|
|
|
|
|
||
Random play*6 |
Press |
repeatedly. |
|
|
|
|
|
||
|
|
DISC RANDOM/ RANDOM OFF |
: Audio CD |
|
|
|
|||
|
|
FOLDER RANDOM/ RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file, iPod |
|||||||
|
|
|
|
|
or ANDROID |
|
|
|
|
|
|
Press and hold |
to select ALL RANDOM.*7 |
|
|
|
|||
*3 |
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the |
||||||||
|
instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application |
||||||||
*4 |
on your Android device before connecting. ( |
24) |
|
|
|
|
|
||
For ANDROID: Applicable only when [BROWSE MODE] is selected. ( 8) |
|
|
|
||||||
*5 |
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID. |
|
|
|
|||||
*6 |
For iPod/ ANDROID: Applicable only when [MODE OFF]/ [BROWSE MODE] is selected. ( |
8) |
|
||||||
*7 |
For CD: Only for MP3/WMA/AAC files. |
|
|
|
|
|
|
|
ENGLISH 7
CD / USB / iPod / ANDROID
Select control mode
While in iPod source, press 5 repeatedly.
MODE ON : Control iPod using the iPod itself. However, you can still play/pause, file skip, fast-forward or reverse from this unit.
MODE OFF : Control iPod from this unit.
While in ANDROID source, press 5 repeatedly.
BROWSE MODE : Control Android device from this unit via KENWOOD MUSIC PLAY application installed in the Android device.
HAND MODE : Control Android device using the Android device itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.
Select music drive
Press 5 repeatedly.
Stored songs in the following drive will be played back.
•Selected internal or external memory of a smartphone (Mass Storage Class).
•Selected drive of a multiple drives device.
Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
Select a file from a folder/list
1 |
Press |
. |
|
2 |
Turn the volume knob to select a folder/list, then press the knob. |
||
3 |
Turn the volume knob to select a file, then press the knob. |
||
|
|
|
|
|
|
Quick Search |
|
|
|
If you have many files, you can search through them quickly. |
|
|
|
Turn the volume knob quickly to browse through the list quickly. |
–Not applicable for iPod.
(or)
Press S / T to search at a preset skip search ratio. (9, [SKIP SEARCH])
•Pressing and holding S / T searches at a 10% ratio.
–Not applicable for audio CD and MP3/WMA/AAC/WAV/FLAC files.
(or)
Alphabet search (applicable only for iPod)
If you have many files in the iPod, you can search through them quickly according to the first character of the file name.
Turn the volume knob quickly to enter character search.
Turn the volume knob to select the character.
To search for a character other than A to Z and 0 to 9, enter only “*”. Press S / T to move to the entry position.
• You can enter up to 3 characters.
Press the volume knob to start searching.
•To return to the root folder/ first file/ top menu, press 5. (Not applicable for BT AUDIO source.)
•To return to the previous setting item, press .
•To cancel, press and hold .
•For iPod, applicable only when [MODE OFF] is selected.
•For ANDROID, applicable only when [BROWSE MODE] is selected.
8
CD / USB / iPod / ANDROID
Direct Music Search (using RC-406)
1 Press DIRECT.
2 Press the number buttons to enter a track/file number. 3 Press to search for music.
•To cancel, press or DIRECT.
•Not available if Random Play is selected.
•Not applicable for iPod and ANDROID.
Other settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select an item (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.
To return to the previous setting item, press .
|
|
Default: XX |
USB |
|
|
|
MUSIC DRIVE |
DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 4]) is selected |
|
|
automatically and playback starts. |
|
|
Repeat steps 1 to 3 to select the following drives. |
|
SKIP SEARCH |
0.5%/ 1%/ 5%/ 10%: While listening to iPod or ANDROID, selects the skip |
|
|
search ratio over the total files. |
|
|
|
AUX
Preparation:
Select [ON] for [BUILT-IN AUX]. ( 5)
Start listening
1 Connect a portable audio player (commercially available).
Auxiliary input jack
Portable audio player
3.5 mm (1/8") stereo mini plug with “L” shaped connector (commercially available)
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 |
Press the volume knob to enter [FUNCTION]. |
|
2 |
Turn the volume knob to select [SYSTEM], then press the knob. |
|
3 |
Turn the volume knob to select [AUX NAME SET], then press the knob. |
|
4 |
Turn the volume knob to select an item, then press the knob. |
|
5 |
AUX (default)/ DVD/ PORTABLE/ GAME/ VIDEO/ TV |
|
Press and hold |
to exit. |
To return to the previous setting item, press .
ENGLISH 9
Pandora®
Preparation:
Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [ON] for [PANDORA SRC]. ( 5)
Start listening
1 Open the Pandora application on your device.
2Connect your device to the USB input terminal.
USB input terminal
KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2
3Press repeatedly to select PANDORA.
Broadcast starts automatically.
To |
|
On the faceplate |
On the remote control |
|
||
Playback / pause |
Press |
. |
Press |
. |
|
|
|
|
|
|
|
|
|
Skip a track |
Press T. |
|
Press |
. |
|
|
|
|
|
|
|
||
Thumbs up or thumbs |
Press J / K. |
Press |
/ |
. |
||
down*3 |
|
|
|
|
|
|
*1 |
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type |
|
|
|
||
*2 |
Do not leave the cable inside the car when not using. |
|
|
|
||
*3 |
If thumbs down is selected, the current track is skipped. |
|
|
|
Create and save a new station
1 |
Press |
. |
2 |
Turn the volume knob to select [NEW STATION], then press the knob. |
3Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (1 to 5) to store.
To select a stored station, press one of the number buttons (1 to 5).
Search for a registered station
1 Press |
. |
2Turn the volume knob to select an item, then press the knob.
[SORT BY DATE]: According to the registered date [SORT BY A-Z]: Alphabetical order
3Turn the volume knob to select the desired station, then press the knob.
To cancel, press and hold . (or using RC-406)
Press J/ K to search for a station, then press .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.
10
Pandora®
Delete a station
While listening to PANDORA...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [SYSTEM], then press the knob.
3Turn the volume knob to select [STATION DEL], then press the knob.
4Turn the volume knob to select [SORT BY A-Z] or [SORT BY DATE], then press the knob.
5Turn the volume knob to select the desired station to delete, then press the knob.
6Turn the volume knob to select [YES], then press the knob.
7 Press and hold to exit.
To return to the previous setting item, press .
iHeartRadio®
Preparation:
Install the latest version of iHeartAuto application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.
• Select [ON] for [IHEART SRC]. ( 5)
Start listening
1 Open the iHeartAuto application on your device.
2Connect your device to the USB input terminal.
USB input terminal
KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2
3Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically.
*1 |
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type |
|
|
|
|
|
*2 |
Do not leave the cable inside the car when not using. |
|
|
|
|
|
To |
|
On the faceplate |
|
On the remote control |
||
|
|
|||||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
|
|
Skip a track for custom station |
Press T. |
|
|
Press |
. |
|
|
|
|
|
|||
Thumbs up or thumbs down |
Press J / K. |
|
( Not available ) |
|||
|
|
|
|
|
||
Create a new/custom station |
Press 1. |
|
|
( Not available ) |
||
|
|
|
|
|
||
Scan for live station |
1 Press 2 to start scanning. |
|
|
|
||
|
|
2 Press |
to listen to the |
|
( Not available ) |
|
|
|
station. |
|
|
|
|
|
|
|
|
|
|
|
ENGLISH 11
iHeartRadio®
Search and store a station
1 Press .
2Turn the volume knob to select a category, then press the knob.
3Turn the volume knob to select the desired station, then press the knob.
When a city list appears, you can search cities in alphabetical order by turning the volume knob quickly.
To cancel, press and hold .
(or using RC-406)
Press J/ K to search for a station, then press
.
•To store a station: Press and hold one of the number buttons (3 to 5).
•To select a stored station: Press one of the number buttons (3 to 5).
SiriusXM® Radio
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com.
Preparation:
1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
Antenna
Expansion port on |
SiriusXM Vehicle Tuner |
the rear panel |
|
2Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its packaging.
The Radio ID does not include the letters I, O, S or F.
3Activate the subscription.
For users in the U.S.A.:
Online: Go to www.siriusxm.com Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to www.siriusxm.ca/activatexm Phone: Call 1-877-438-9677
4 Press repeatedly to select SIRIUS XM to start updating.
Start listening
1 Press repeatedly to select SIRIUS XM.
2 Press repeatedly to select a band.
3 Press .
“” lights up.
4Turn the volume knob to select a category, then press the knob.
If “ALL CHANNELS” is selected, all the available channels will be shown.
12
SiriusXM® Radio
5Turn the volume knob to select a channel, then press the knob.
(or)
Press S/ Tto search for a channel manually.
•Pressing and holding S/ Tchanges the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 14)
To change the tuning method for S/ T: Press
.
Each time you press , the tuning method switches between “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).
Direct Access Tuning (using RC-406)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a channel number. 3 Press to start searching.
•To cancel, press or DIRECT.
•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.
SiriusXM Keymode
Press and hold to change the keymode (channel or replay).
(Default: Channel keymode)
“” lights up when replay keymode is selected.
When channel keymode is selected...
To |
On the faceplate |
|
On the remote control |
|
||
Select a channel |
Press S/ T. |
|
Press S/ |
. |
|
|
|
|
|
|
|
||
Change a channel |
Press and hold S/ T. |
|
Press and hold S/ |
. |
||
rapidly |
|
|
|
|
|
|
Store a channel of the |
Press and hold one of the |
|
(Not available) |
|
|
|
current band |
number buttons (1 to 6). |
|
|
|
||
|
|
|
|
|||
|
|
|
|
|
|
|
Select a stored |
Press one of the number buttons (1 to 6). |
|
|
|||
channel of the current |
|
|
|
|
|
|
band |
|
|
|
|
|
|
When replay keymode is selected... |
|
|
|
|
|
|
To |
On the faceplate |
|
On the remote control |
|
||
|
|
|||||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
|
|
Select a track |
Press S/ T. |
|
Press S/ |
. |
|
|
|
|
|
|
|
||
Rewind / Fast-forward |
Press and hold S/ T. |
|
Press and hold S/ |
. |
||
|
|
|
|
|
|
|
Go to Live |
Press 1. |
|
|
|
|
|
|
|
|
|
|
|
|
SmartFavorites and TuneStart™
User stored channels are recognized as SmartFavorite channels*. The SiriusXM Vehicle Tuner automatically buffers the broadcast content in the background.
• SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle Tuner.
*SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites. The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as SmartFavorites.
When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
•Playback starts from the beginning of the song if [TUNE START] is set to [ON] ( 14) for most music channels stored as a SmartFavorite.
Press one of the number buttons (1 to 6) to select a stored channel.
ENGLISH 13
SiriusXM® Radio
TuneScan™
You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel.
Press and hold to start scanning the first 6 seconds of the recorded music contents.
•To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.
•To select the previous/next song, press S / T.
•To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.
SiriusXM settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [SIRIUS XM], then press the knob.
3Turn the volume knob to select an item (see the following table), then press the knob.
4Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item.
5 Press and hold |
to exit. |
To return to the previous setting item, press .
Default: XX
CHANNEL LOCK |
To unlock settings: |
|
|||
|
|
|
1 |
Turn the volume knob to select a number. |
|
|
|
|
2 |
Press S / T to move to the entry position. |
|
|
|
|
3 |
Repeat steps 1 and 2 to enter the current pass code. |
|
|
|
|
4 |
(Initial pass code is 0000.) |
|
|
|
|
Press the volume knob to confirm. |
||
|
|
|
|||
|
CODE SET |
1 Turn the volume knob to select a number. |
|||
|
|
|
2 |
Press S / T to move to the entry position. |
|
|
|
|
3 |
Repeat steps 1 and 2 to enter a new 4-digit pass code. |
|
|
|
|
4 |
Press the volume knob to confirm. |
|
|
|
|
5 |
Repeat steps 1 to 4 to reconfirm the pass code. |
|
|
|
|
• Make a note of the new pass code to enter channel lock settings for next time. |
||
|
|
|
|||
|
LOCK SETTING |
MATURE CH: Selects the SiriusXM-defined lock setting. ; USER DEFINED: Selects |
|||
|
|
|
the individual channels the user wants to lock. ; OFF: Cancels. |
||
|
|
|
|||
|
CHANNEL EDIT*1 |
1 Turn the volume knob to select a category, then press the knob. |
|||
|
|
|
2 |
Turn the volume knob to select a channel you want to lock, then press the |
|
|
|
|
|
knob. |
|
|
|
|
3 |
“L” appears in front of the channel number. |
|
|
|
|
Press and hold |
to exit. |
|
|
|
|
|||
|
CHANNEL CLEAR*1 |
YES: Clears all the locked channels. ; NO: Cancels. |
|||
|
TUNE START*2 |
ON: All qualified music channels in the SmartFavorite will start playback from the |
|||
|
|
|
beginning of the song. ; OFF: Cancels. |
||
|
SIGNAL LEVEL |
NO SIGNAL/ WEAK/ GOOD/ STRONG: Shows the strength of the current received |
|||
|
|
|
signal. |
|
|
|
BUFFER USAGE |
0% — 100% (0): Shows the memory usage for Replay buffer. |
|||
|
|
|
|||
|
SXM RESET |
YES: Resets stored channel and lock setting to default. ; NO: Cancels. |
|||
|
|
|
|||
*1 |
Displayed only when [USER DEFINED] is selected. |
||||
*2 |
Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports SmartFavorites. |
14
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
–Hands-Free Profile (HFP)
–Advanced Audio Distribution Profile (A2DP)
–Audio/Video Remote Control Profile (AVRCP)
–Serial Port Profile (SPP)
–Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
–Sub Band Codec (SBC)
–Advanced Audio Coding (AAC)
–aptX Codec (aptX)
Connect the microphone
MIC (Microphone input terminal) |
Microphone |
|
|
|
(supplied) |
Rear panel
Adjust the microphone angle
Secure using cord clamps (not supplied) if necessary.
Pair and connect a Bluetooth device for the first time
1 Press to turn on the unit.
2Search and select this unit model name (KDC-X7**/ KDC-BT7**HD) on the Bluetooth device.
“PAIRING” “PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” scrolls on the display.
•For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.
3Press the volume knob to start pairing.
“PAIRING OK” appears when pairing is completed.
•This unit supports Secure Simple Pairing (SSP).
•Up to 10 devices can be registered (paired) in total.
•Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, 19, [DEVICE DELETE].
Once pairing is completed, Bluetooth connection is established automatically. “BT1” and/or “BT2” on the display window lights up.
•A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.
•Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.
•Refer to the instruction manual of the Bluetooth device for more information.
Auto Pairing
When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.
Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if:
–Bluetooth function of the connected devcie is turned on.
–[AUTO PAIRING] is set to [ON]. ( 19)
–KENWOOD MUSIC PLAY application is installed on the Android device ( 7) and [BROWSE MODE] is selected ( 8).
ENGLISH 15
BLUETOOTH®
Connect with a remote device by One-touch (NFC)
Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices.
By holding an NFC-compatible remote device near to the N-Mark on the unit (volume knob), the unit and remote device proceed to complete pairing and
established the BLUETOOTH connection automatically.
1Activate the NFC function on the remote device.
Refer to the instruction manual of the remote device for more information.
2Hold the remote device near to the N-Mark on the unit (volume knob).
The device vibrates when pairing is completed.
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
• The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 17) During a call:
•The buttons and display illuminate according to the settings made for [DISPLAY]. ( 23)
•If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
The following operations may differ or not available depending on the connected phone.
•To disconnect, hold the remote device near to the N-Mark on the unit (volume knob) again.
•This unit only can recognize and connect to one NFCcompatible device at a time.
|
To |
On the faceplate |
On the remote control |
||
First incoming call... |
|
|
|
|
|
|
Answer a call |
Press |
or the volume knob |
Press . |
|
|
|
or one of the number buttons |
|
|
|
|
|
(1 to 6). |
|
|
|
|
|
|
|
|
|
|
Reject a call |
Press |
. |
Press |
. |
|
|
|
|
|
|
|
End a call |
Press |
. |
Press |
. |
|
|
|
|
|
|
16
BLUETOOTH®
To |
On the faceplate |
On the remote control |
|
|
|
While talking on the first incoming call...
|
Answer another incoming |
Press . |
|
Press . |
|
|
call and hold the current call |
|
|
|
|
|
|
|
|
|
|
|
Reject another incoming call |
Press |
. |
Press |
. |
|
|
|
|
|
|
While having two active calls... |
|
|
|
|
|
|
|
|
|
|
|
|
End current call and activate |
Press |
. |
Press |
. |
|
held call |
|
|
|
|
|
Swap between the current |
Press . |
|
Press . |
|
|
call and held call |
|
|
|
|
Adjust the phone volume |
Turn the volume knob during |
|
|
||
[00] to [35] (Default: [15]) |
a call. |
|
( Not available ) |
||
|
|
• This adjustment will not |
|||
|
|
affect the volume of the other |
|
|
|
|
|
sources. |
|
|
|
|
|
|
|
|
|
Switch between hands-free |
Press |
during a call. |
|
|
|
and private talk modes |
• Operations may vary |
( Not available ) |
|||
|
|
according to the connected |
|||
|
|
|
|
||
|
|
Bluetooth device. |
|
|
|
|
|
|
|
|
|
Improve the voice quality
While talking on the phone...
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
|
Default: XX |
MIC GAIN |
–10 — +10 (–4): The sensitivity of the |
|
microphone increases as the number increased. |
|
|
NR LEVEL |
–5 — +5 (0): Adjust the noise reduction level |
|
until the least noise is being heard during a |
|
phone conversation. |
|
|
ECHO CANCEL |
–5 — +5 (0): Adjust the echo cancellation |
|
delay time until the least echo is being heard |
|
during a phone conversation. |
|
|
Make the settings for receiving a call 1 Press to enter Bluetooth mode.
2Turn the volume knob to select an item (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
|
|
Default: XX |
SETTINGS |
|
|
|
|
|
|
AUTO ANSWER |
1 — 30: The unit answers incoming call |
|
|
automatically in the selected time (in |
|
|
seconds). ; OFF: Cancels. |
|
|
|
|
BATT/SIGNAL* |
AUTO: Shows the strength of the battery |
|
|
and signal when the unit detects a Bluetooth |
|
|
device and the Bluetooth device is connected. ; |
|
|
OFF: Cancels. Clock time is shown. |
|
|
|
* Functionality depends on the type of the phone used.
ENGLISH 17
BLUETOOTH®
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
2Turn the volume knob to select an item (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press and hold |
to exit. |
To return to the previous setting item, press .
CALL HISTORY (Applicable only if the phone supports PBAP)
1Press the volume knob to select a name or a phone number.
•“INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.
•Press DISP to change the display category (NUMBER or NAME).
•“NO DATA” appears if there is no recorded call history.
2 Press the volume knob to call.
PHONE BOOK (Applicable only if the phone supports PBAP)
1Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts).
The first menu (ABCDEFGHIJK) appears.
•To go to the other menu (LMNOPQRSTUV or WXYZ1*), press J/ K.
•To select the desired first letter, turn the volume knob or press S / T, then press the knob.
Select “1” to search with numbers and select “*” to search with symbols. 2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
•The phonebook of the connected phone is automatically transferred to the unit when pairing.
•Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL
•This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
NUMBER DIAL |
1 Turn the volume knob to select a number (0 to 9) or |
|
character ( , #, +). |
2Press S / T to move the entry position. Repeat steps 1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
(or using RC-406)
1Press the number buttons (0 to 9) to enter the phone number.
|
2 Press |
to call. |
VOICE |
Speak the name of the contact you want to call or the |
|
|
voice command to control the phone functions. |
|
|
( Make a call using voice recognition) |
BATT LOW/ MID/ FULL*: Shows the strength of the battery.
NO SIGNAL/ LOW/ MID/ MAX*: Shows the strength of the current received signal.
* Functionality depends on the type of the phone used.
Make a call using voice recognition
1Press and holdto activate the voice recognition of the connected phone.
2Speak the name of the contact you want to call or the voice command to control the phone functions.
•Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
•This unit also supports the intelligent personal assistant function of iPhone.
18
BLUETOOTH®
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press to enter Bluetooth mode.
2Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob.
3Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone number.
4Press and hold one of the number buttons (1 to 6).
“STORED” appears when the contact is stored.
To erase a contact from the preset memory, select [NUMBER DIAL] in step 2 and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1 to 6).
3Press the volume knob to call.
“NO MEMORY” appears if there is no contacts stored.
Other settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select an item (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press and hold |
to exit. |
To return to the previous setting item, press .
|
|
|
Default: XX |
BT MODE |
|
|
|
|
|
|
|
|
PHONE SELECT |
Selects the phone or audio device to connect or disconnect. |
|
|
|
“*” appears in front of the device name when connected. |
|
|
AUDIO SELECT |
• |
You can only connect a maximum of two Bluetooth phones and one |
|
|
|
Bluetooth audio device at any time. |
|
|
|
|
|
DEVICE DELETE |
1 |
Turn the volume knob to select a device to delete, then press the |
|
|
2 |
knob. |
|
|
Turn the volume knob to select [YES] or [NO], then press the knob. |
|
|
PIN CODE EDIT |
Changes the PIN code (up to 6 digits). |
|
|
(0000) |
1 |
Turn the volume knob to select a number. |
|
|
2 |
Press S / T to move the entry position. |
|
|
3 |
Repeat steps 1 and 2 until you finish entering the PIN code. |
|
|
Press the volume knob to confirm. |
|
|
RECONNECT |
ON: The unit automatically reconnect when the last connected |
|
|
|
Bluetooth device is within range. ; OFF: Cancels. |
|
|
|
|
|
|
AUTO PAIRING |
ON: The unit automatically pair supported Bluetooth device (iPhone/ |
|
|
|
iPod touch/ Android device) when it is connected through USB input |
|
|
|
terminal. Depending on the operating system of the connected device, |
|
|
|
this function may not work. ; OFF: Cancels. |
|
|
|
|
|
|
INITIALIZE |
YES: Initializes all the Bluetooth settings (including stored pairing, |
|
|
|
phonebook, and etc.). ; NO: Cancels. |
|
|
|
|
|
ENGLISH 19
BLUETOOTH®
Bluetooth test mode
You can check the connectivity of the supported profile between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1Press and hold .
“PLEASE PAIR YOUR PHONE PIN 0000” appears.
2 Search and select this unit model name (KDCdevice.-X7**/ KDC-BT7**HD) on the Bluetooth
3Operate the Bluetooth device to confirm pairing.
“TESTING” flashes on the display.
The connectivity result (OK or NG) appears after
the test. |
|
|
PAIRING: |
Pairing status |
|
HF CNT: |
Hands-Free Profile (HFP) compatibility |
|
AUD CNT: Advanced Audio Distribution Profile |
||
|
(A2DP) compatibility |
|
PB DL: |
Phonebook Access profile (PBAP) |
|
|
compatibility |
|
To cancel test mode, press and hold |
to turn |
|
off the unit. |
|
BLUETOOTH — Audio
Audio player via Bluetooth
1 Press |
repeatedly to select BT AUDIO (or press SRC on RC-406). |
|
|
||||
2 Operate the Bluetooth audio player to start playback. |
|
|
|
||||
To |
|
On the faceplate |
|
On the remote control |
|
||
|
|
|
|||||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
|
|
||
Select group or folder |
Press J/ K. |
|
Press |
/ |
. |
||
|
|
|
|
|
|
||
Reverse / Forward skip |
Press S / T. |
|
Press S / |
. |
|
||
|
|
|
|
||||
Reverse / Fast-forward |
Press and hold S / T. |
Press and hold S / |
. |
||||
|
|
|
|
|
|
|
|
Repeat play |
|
Press |
repeatedly. |
( Not available ) |
|
||
|
|
ALL REPEAT, FILE REPEAT, REPEAT OFF |
|
||||
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
Random play |
|
Press and hold |
to select |
|
|
|
|
|
|
ALL RANDOM. |
|
( Not available ) |
|
||
|
|
• Press |
to select RANDOM OFF. |
|
|
|
|
Select a file from a |
Refer to “Select a file from a |
( Not available ) |
|
||||
folder/list |
|
folder/list” on page 8. |
|
||||
|
|
|
|
Operations and display indications may differ according to their availability on the connected device.
20
BLUETOOTH®
Internet radio via Bluetooth
Listen to Pandora
You can listen to Pandora on the Android device via Bluetooth on this unit.
Preparation:
Select [ON] for [PANDORA SRC]. ( 5)
1 Open the Pandora application on your device.
2Connect your Bluetooth audio player via Bluetooth connection. ( 15)
3Press repeatedly to select PANDORA.
The source switches and broadcast starts automatically.
You can operate Pandora in the same way as Pandora for iPod/iPhone. ( 10)
Listen to iHeartRadio
You can listen to iHeartRadio on the Android device via Bluetooth on this unit.
Preparation:
Select [ON] for [IHEART SRC]. ( 5)
1 Open the iHeartAuto application on your smart phone.
2 Connect your smart phone via Bluetooth connection. ( 15)
3Press repeatedly to select IHEARTRADIO.
The source switches and broadcast starts automatically.
You can operate iHeartRadio in the same way as iHeartRadio for iPod/ iPhone. ( 11)
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [AUDIO CONTROL], then press the knob.
3Turn the volume knob to select an item (see the following table), then press the knob.
4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [AUDIO CONTROL].
2 Press J/ K to select an item, then press .
To return to the previous setting item, press .
|
|
|
Default: XX |
SUB-W LEVEL |
–50 to +10 (0): Adjusts the subwoofer output level. |
||
|
|
|
|
MANUAL EQ |
|
|
|
|
|
|
|
|
BAND1 LEVEL |
LEVEL |
–9 to +9 (0): (Refer to BAND2 LEVEL below.) |
|
|
BASS EXTEND |
ON: Turns on the extended bass. ; OFF: Cancels. |
BAND2 LEVEL to –9 to +9 (0): The sound elements (frequency level, tone level, Q factor)
BAND13 LEVEL are preset into each selection (BAND1 LEVEL to BAND13 LEVEL). Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)
Q FACTOR |
1.35/ 1.50/ 2.00: Adjust the quality factor. |
PRESET EQ |
NATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL/ USER: |
|
Selects a preset equalizer suitable to the music genre. (Select [USER] to |
|
use the settings made in [MANUAL EQ].) |
BASS BOOST |
LEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5: Selects your preferred |
|
bass boost level. ; OFF: Cancels. |
ENGLISH 21
AUDIO SETTINGS
LOUDNESS |
LEVEL1/ LEVEL2: Selects your preferred low and high |
|
|
|
frequencies boost to produce a well-balanced sound at a low |
|
|
volume level. ; OFF: Cancels. |
|
|
|
SUBWOOFER SET |
ON: Turns on the subwoofer output. ; OFF: Cancels. |
|
|
|
|
FADER |
R15 to F15 (0): Adjusts the rear and front speaker output |
|
|
|
balance. |
BALANCE |
L15 to R15 (0): Adjusts the left and right speaker output |
|
|
|
balance. |
VOLUME OFFSET |
–15 to +6 (0): Preset the initial volume level of each source. |
|
|
|
(Before adjustment, select the source you want to adjust.) |
SOUND EFFECT |
|
|
|
|
|
|
SOUND RECNSTR |
(Not applicable for TUNER source, AUX source and SIRIUS XM source.) |
|
(Sound reconstruction) |
ON: Creates realistic sound by compensating the high- |
|
|
frequency components and restoring the rise-time of |
|
|
the waveform that are lost in audio data compression. ; |
|
|
OFF: Cancels. |
|
|
|
|
SPACE ENHANCE |
(Not applicable for TUNER source.) |
|
|
SMALL/ MEDIUM/ LARGE: Virtually enhances the sound |
|
|
space. ; OFF: Cancels. |
|
|
|
|
SND REALIZER |
LEVEL1/ LEVEL2/ LEVEL3: Virtually makes the sound more |
|
|
realistic. ; OFF: Cancels. |
|
|
|
|
STAGE EQ |
LOW/ MIDDLE/ HIGH: Virtually adjust the sound position |
|
|
heard from the speakers. ; OFF: Cancels. |
|
|
|
|
DRIVE EQ |
ON: Boosts the frequency to reduce the noise heard from |
|
|
outside the car or running noise of the tyres. ; OFF: Cancels. |
|
|
|
SPEAKER SIZE
|
FRONT |
SIZE |
3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ |
|
|
|
6×8/ 6×9/ 7×10: Selects according to the connected |
|
|
|
speaker size for optimum performance. |
|
|
|
|
|
|
TWEETER |
SMALL/ MIDDLE/ LARGE: Selects according to the |
|
|
|
size range of the connected tweeter for optimum |
|
|
|
performance. ; NONE: Not connected. |
|
|
|
|
|
REAR |
3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ 6×8/ 6×9/ 7×10: |
|
|
|
Selects according to the connected speaker size for optimum performance. ; |
|
|
|
NONE: Not connected. |
|
|
|
|
|
|
SUBWOOFER |
6.5"/ 8"/ 10"/ 12"/ 15" OVER: Selects according to the connected speaker |
|
|
|
size for optimum performance. ; NONE: Not connected. |
|
|
|
|
|
X ' OVER |
|
|
|
|
TWEETER |
FRQ |
1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ |
|
|
|
8KHZ/ 10KHZ/ 12.5KHZ: Adjusts the crossover |
|
|
|
frequency for the tweeter speaker. |
|
|
|
|
|
|
GAIN LEFT |
–8 to 0: Adjusts the output volume of the left tweeter. |
|
|
|
|
|
|
GAIN RIGHT |
–8 to 0: Adjusts the output volume of the right tweeter. |
|
|
|
|
|
FRONT HPF |
F - HPF FRQ |
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ |
|
|
|
100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ: |
|
|
|
Adjusts the crossover frequency for the selected |
|
|
|
speakers (high pass filter). ; THROUGH: All signals are |
|
|
|
sent to the selected speakers. |
|
|
|
|
|
|
F - HPF SLOPE |
–6DB/ –12DB/ –18DB/ –24DB: Adjusts the |
|
|
|
crossover slope. (Selectable only if a setting other than |
|
|
|
[THROUGH] is selected for [F - HPF FRQ].) |
|
|
|
|
|
|
F - HPF GAIN |
–8 to 0: Adjusts the output volume of the selected |
|
|
|
speaker. |
|
|
|
|
22
AUDIO SETTINGS |
|
DISPLAY SETTINGS |
|
REAR HPF |
R - HPF FRQ |
|
|
|
|
(Refer FRONT HPF, 22.) |
|
|
R - HPF SLOPE |
|
|
|
|
|
|
|
R - HPF GAIN |
|
|
|
|
|
|
SUBWOOFER LPF |
SW LPF FRQ |
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ |
|
|
|
100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ: |
|
|
|
Adjusts the crossover frequency for the subwoofer |
|
|
|
(low pass filter). ; THROUGH: All signals are sent to |
|
|
|
the subwoofer. |
|
|
|
|
|
|
SW LPF SLOPE |
–6DB/ –12DB/ –18DB/ –24DB: Adjusts the |
|
|
|
crossover slope. (Selectable only if a setting other |
|
|
|
than [THROUGH] is selected for [SW LPF FRQ].) |
|
|
|
|
|
|
SW LPF PHASE |
REVERSE (180°)/ NORMAL (0°): Selects the phase |
|
|
|
of the subwoofer output to be in line with the |
|
|
|
speaker output for optimum performance. |
|
|
|
|
|
|
SW LPF GAIN |
–8 to 0: Adjusts the output volume of the |
|
|
|
subwoofer. |
|
|
|
|
•[SUB-W LEVEL]/ [SUBWOOFER] of [SPEAKER SIZE]/ [SUBWOOFER LPF] of [X ‘ OVER] is selectable only if [SUBWOOFER SET] is set to [ON]. ( 22)
•[TWEETER], [REAR HPF] and [SUBWOOFER LPF] of [X ‘ OVER] is selectable only if a setting other than [NONE] is selected for [TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE]. ( 22)
•Once you have selected the speaker size ([SPEAKER SIZE], 22), the frequency and slope settings are automatically set for the crossover of the selected speaker.
: ZONE 1
ALL ZONE
: ZONE 2
Set the dimmer
Press and hold DISP (DIM) to turn on or off the dimmer.
•If you have set [DIMMER TIME] ( 24), it will be canceled once you press and hold this button.
Other settings
1 |
Press the volume knob to enter [FUNCTION]. |
|
2 |
Turn the volume knob to select [DISPLAY], then press the knob. |
|
3 |
Turn the volume knob to select an item ( 24), then press the knob. |
|
4 |
Repeat step 3 until the desired item is selected/activated or follow |
|
5 |
the instructions stated on the selected item. |
|
Press and hold |
to exit. |
To return to the previous setting item, press .
ENGLISH 23
DISPLAY SETTINGS
|
|
Default: XX |
COLOR SELECT |
VARIABLE SCAN/ CUSTOM R/G/B/ preset colors*: Selects your preferred |
|
|
color for button illumination and display illumination. |
|
|
To make your own color, select [CUSTOM R/G/B]. The color you have |
|
|
made will be stored in [CUSTOM R/G/B]. |
|
|
1 |
Press the volume knob to enter the detailed color adjustment. |
|
2 |
Press S/ Tto select the color (R/ G/ B) to adjust. |
|
3 |
Turn the volume knob to adjust the level (0 — 9), then press the knob. |
|
|
|
DIMMER |
Dim the display illumination and button illumination. |
|
|
ON: Dimmer is turned on. ; OFF: Cancels. |
|
|
DIMMER TIME: Set the dimmer on and off time. |
|
|
1 |
Turn the volume knob to adjust the [ON] time, then press the knob. |
|
2 |
Turn the volume knob to adjust the [OFF] time, then press the knob. |
|
(Default: [ON]: 6:00 PM; [OFF]: 6:00 AM) |
|
|
|
|
BRIGHTNESS |
1 Select a zone for setting. ( 23) |
|
|
2 |
0 — 31: Selects your preferred brightness level for display illumination |
|
|
and button illumination. |
TEXT SCROLL |
AUTO/ ONCE: Selects whether to scroll the display information |
|
|
automatically, or scroll only once. ; OFF: Cancels. |
|
|
|
|
*Preset colors: RED1/ RED2/ RED3/ PURPLE1/ PURPLE2/ PURPLE3/ PURPLE4/ BLUE1/ BLUE2/ BLUE3/ SKYBLUE1/ SKYBLUE2/ LIGHTBLUE/ AQUA1/ AQUA2/ GREEN1/ GREEN2/ GREEN3/ YELLOWGREEN1/ YELLOWGREEN2/ YELLOW/ ORANGE1/ ORANGE2/
ORANGERED
REFERENCES
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector
Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.
Connector (on the reverse side of the faceplate)
Handling discs
•Do not touch the recording surface of the disc.
•Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
•Do not use any accessories for the disc.
•Clean from the center of the disc and move outward.
•Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
•When removing discs from this unit, pull them out horizontally.
•Remove burrs from the center hole and disc edge before inserting a disc.
More information
Visit also the following website <www.kenwood.com/cs/ce/> for:
–Latest firmware updates and latest compatible item list
–Android™ application KENWOOD MUSIC PLAY
–Any other latest information
General
•This unit can only play the following CDs:
•Detailed information and notes about the playable audio files are stated in an online manual on the following website: www.kenwood.com/cs/ce/audiofile/
24
REFERENCES
Playable files
•Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.aac)
•Playable disc media: CD-R/CD-RW/CD-ROM
•Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
•Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.
The AAC (.m4a) file in a USB device or a CD encoded by iTunes cannot be played on this unit.
Unplayable discs
•Discs that are not round.
•Discs with coloring on the recording surface or discs that are dirty.
•Recordable/ReWritable discs that have not been finalized.
•8 cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
•This unit can play MP3/WMA/AAC/WAV/FLAC files stored on a USB mass storage class device.
•You cannot connect a USB device via a USB hub.
•Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
•This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1.5 A.
About iPod/iPhone
Made for
-iPod touch (2nd, 3rd, 4th, and 5th generation)
-iPod classic
-iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
-iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus
•You cannot operate iPod if “KENWOOD” or “” is displayed on iPod.
•Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit.
About Android device
•This unit supports Android OS 4.1 and above.
•Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0.
•If the Android device supports both mass storage class device and AOA 2.0, this unit always playback via AOA 2.0 as priority.
About Pandora
•Pandora is only available in certain countries.
Please visit <http://www.pandora.com/legal> for more information.
•Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
•Some functions of Pandora cannot be operated from this unit.
•For issues using the application, please contact Pandora at pandora-support@pandora.com.
About iHeartRadio
•iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
•Some iHeartRadio® functionality cannot be operated from this unit.
About Bluetooth
•Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.
•This unit may not work with some Bluetooth devices.
•Signal conditions vary, depending on the surroundings.
•Compatible remote device for NFC function:
Remote devices with a NFC function (OS: Android™ 2.3.3 or later, excluding Android 3.x). If the OS version of your remote device is older than Android 4.1.x, download and start the
“NFC Easy Connect” application. (“NFC Easy Connect” is a free application available at Google Play.)
ENGLISH 25
REFERENCES
About HD Radio™ Technology
• Adjacent to traditional main stations are HD2/HD3 Channels, providing new original programming on the FM dial.
• HD Radio broadcasts deliver crystal clear, CD-like digital audio quality to consumers; eliminates background noise.
• Program Info provides song name, artist, station ID, and other relevant data to enrich the listening experience.
Change the display information
Each time you press DISP, the display information changes.
•If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg. station name, playing time) appears.
Source name |
|
Display information |
|
STANDBY |
Source name (Date/Clock)* |
|
|
|
|
|
|
HD RADIO |
Frequency (Date/Clock)* |
|
|
|
(For digital stations only) |
|
|
|
Station name (Date/Clock)* |
Song title (Artist) |
Song title (Album title) |
|
Song title (Date/Clock)* |
Frequency (Date/Clock)* |
|
|
(back to the beginning) |
|
|
|
|
||
|
(For FM Radio Broadcast Data System stations only) |
||
|
Station name (Date/Clock)* |
Radio text (Date/Clock)* Radio text+ |
|
|
(R.TEXT+) Title (Artist) |
Title (Date/Clock)* |
Frequency (Date/Clock)* |
|
(back to the beginning) |
|
|
CD or USB |
(For CD-DA) |
|
Track title (Artist) Track title (Disc name) Track title (Date/Clock)* |
|
Playing time (Date/Clock)* (back to the beginning) |
(For MP3/WMA/AAC/WAV/FLAC files)
Track title (Artist) Track title (Album title) Track title (Date/Clock)* File name (Folder name) File name (Date/Clock)* Playing time (Date/Clock)* (back to the beginning)
Source name |
|
Display information |
||
|
|
|
|
|
iPod or ANDROID |
Track title (Artist) |
Track title (Album name) |
Track title (Date/Clock)* |
|
|
Playing time (Date/Clock)* |
(back to the beginning) |
||
|
|
|
||
PANDORA |
Station name (Date/Clock)* |
Shared / Radio station (Date/Clock)* |
||
|
Track title (Artist) |
Track title (Album title) |
Track title (Date/Clock)* |
|
|
Playing time (Date/Clock)* |
(back to the beginning) |
||
IHEARTRADIO |
Station name (Date/Clock)* |
Track title (Artist) Track title |
||
|
(Date/Clock)* (back to the beginning) |
|
||
SIRIUS XM |
Channel number (Status) |
Channel name (Status) Artist name |
||
|
(Status) Song title (Status) Content information (Status) |
|||
|
Category name (Status) Clock (Status) |
(back to the beginning) |
||
|
|
|
|
|
BT AUDIO |
Track title (Artist) |
Track title (Album name) |
Track title (Date/Clock)* |
|
|
Playing time (Date/Clock)* |
(back to the beginning) |
||
|
|
|
|
|
AUX |
Source name (Date/Clock)* |
|
|
|
|
|
|
|
|
*Battery and signal strength of the Bluetooth device will be shown if [BATT/SIGNAL] is set to [AUTO]. ( 17)
26