Kenwood KDC-X399, KDC-MP362BT, KDC-BT362U, KMR-D362BT User Manual

KDC-X399 KDC-MP362BT

KDC-BT362U KMR-D362BT

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model KDC-X399/ KDC-BT362U/ KDC-MP362BT/ KMR-D362BT Serial number

US Residents Only

Register Online

Register your Kenwood product at www.Kenwoodusa.com

© 2014 JVC KENWOOD Corporation

B5A-0142-00 (KN)

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.

A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

i

IC (Industry Canada) Notice

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1)l’appareil ne doit pas produire de brouillage, et

(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.

Para cumplimiento de la COFETEL:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1)es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2)este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada”

Contains Bluetooth Module	FCC ID:	ZWYMC55
Contains Bluetooth Module	IC:	12033A-MC55

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences

radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

ii

CONTENTS

	BEFORE USE					2
	BASICS					3
	GETTING STARTED					4
	RADIO					5
	CD / USB / iPod / ANDROID					7
	Pandora®					9
	(except for				)
	iHeartRadio®					10
	(except for				)
	SiriusXM® Radio					11
	(for			)
	BLUETOOTH®					13
	AUX					19
	AUDIO SETTINGS					19
	DISPLAY SETTINGS					21
	MORE INFORMATION					21
	TROUBLESHOOTING					22
	SPECIFICATIONS					25
	INSTALLATION /
	CONNECTION					27

How to read this manual

•Operations are explained mainly using buttons on the faceplate.

•[XX] indicates the selected items.

•( XX) indicates references are available on the stated page.

BEFORE USE

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

•Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•Avoid using the external device if it might hinder safe driving.

•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

•If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to

evaporate.

Remote control (RC-406):

•Do not leave the remote control in hot places such as on the dashboard.

•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

•Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

Maintenance

Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector: Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

Handling discs:

•Do not touch the recording surface of the disc.

•Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

•Do not use any accessories for the disc.

•Clean from the center of the disc and move outward.

•Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

•When removing discs from this unit, pull them out horizontally.

•Remove burrs from the center hole and disc edge before inserting a disc.

Connector (on the reverse side of the faceplate)

2

BASICS

Faceplate

Remote control (RC-406) (supplied for

/

Volume knob

/

)

(turn/press)

Loading slot

Display window

Remote sensor (Do not expose

to bright sunlight.)

	Pull out the
	insulation sheet
	when using for the
	first time.
Detach button	Remote control functions are not available for
	.

Attach	Detach	How to reset	How to replace the battery
			Your preset
			adjustments will also
			be erased.

To	On the faceplate		On the remote control
Turn on the power	Press	.	Press and hold SRC to turn off the power.
	• Press and hold to turn off the power.*1		( Pressing SRC does not turn on the power. )
Adjust the volume	Turn the volume knob.		Press	or	.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Select a source					Press	repeatedly.		Press SRC repeatedly.
Change the display					Press	repeatedly.		( not available )
information*2					• Press and hold to scroll the current display information.
*1	For		: The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off).
*2	For				: You can also select to turn off the display information by pressing		repeatedly.

ENGLISH 3

GETTING STARTED

1Cancel the demonstration (except for )

When you turn on the power (or after you reset the unit), the display shows: “CANCEL DEMO”“PRESS”“VOLUME KNOB”

1Press the volume knob.

[YES] is selected for the initial setup.

2Press the volume knob again.

“DEMO OFF” appears.

2Set the clock

1 Press the volume knob to enter [FUNCTION].

2 Turn the volume knob to select [CLOCK], then press the knob.

3 Turn the volume knob to select [CLOCK ADJUST], then press the knob.

4Turn the volume knob to make the settings, then press the knob.

DayHourMinute

5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob. 7 Press and hold to exit.

To return to the previous setting item, press .

3Set the initial settings

1 Press repeatedly to enter STANDBY. 2 Press the volume knob to enter [FUNCTION].

3Turn the volume knob to make a selection (see the following table), then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

				Default: XX
AUDIO CONTROL
	SWITCH	(For		)
	PREOUT	REAR/ SUBWOOFER: Selects whether rear speakers or a subwoofer are
		connected to the line out terminals on the rear (through an external
		amplifier).
	SP SELECT	OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches
		or 4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum
		performance.
DISPLAY
	EASY MENU	ON: Both display and button illumination change to white color when
		entering [FUNCTION]. ; OFF: Both display and button illumination
		remain as [COLOR SELECT] color. ( 21)
TUNER SETTING
	PRESET TYPE	NORMAL: Memorizes one station for each preset button in each band
		(FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel
		for each preset button, regardless of the selected band or SiriusXM
		channel.

4

GETTING STARTED

RADIO

SYSTEM

KEY BEEP		ON: Activates the keypress tone. ; OFF: Deactivates.
SOURCE SELECT
	PANDORA SRC	(Except for		)
		ON: Enables PANDORA in source selection. ;
		OFF: Disables. ( 9)
	IHEART SRC	(Except for		)
		ON: Enables IHEARTRADIO in source selection. ;
		OFF: Disables. ( 10)
	BUILT-IN AUX	ON: Enables AUX in source selection. ; OFF: Disables.
		( 19)
CD READ		1: Automatically distinguishes between audio file disc
		and music CD. ; 2: Forces to play as a music CD. No
		sound can be heard if an audio file disc is played.

F/W UPDATE

UPDATE SYSTEM / UPDATE BT

F/W UP xx.xx YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated).

For details on how to update the firmware, see: www.kenwood.com/cs/ce/

CLOCK

CLOCK DISPLAY ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels.

Search for a station

1 Press

repeatedly to select TUNER.

2Pressrepeatedly (or press/on RC-406) to select FM1/ FM2/ FM3/ AM.

3 Press S / T (or press S /

on RC-406) to search for a station.

•To change the searching method for S / T: Pressrepeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

•To store a station: Press and hold one of the number buttons (1 to 6).

•To select a stored station: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).

Direct Access Tuning (using RC-406) (except for)

1 Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a frequency.

3Pressto search for a station.

•To cancel, pressor DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

ENGLISH 5

RADIO

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

				Default: XX
TUNER SETTING
	AUTO	YES: Automatically starts memorizing 6 stations with good reception. ; NO: Cancels.
	MEMORY	• Selectable only if [NORMAL] is selected for [PRESET TYPE]. ( 4)
	MONO SET	ON: Improves the FM reception, but the stereo effect may be lost. ; OFF: Cancels.
	NEWS SET	(For		)
		ON: The unit will temporarily switch to News Programme if available. ; OFF: Cancels.
	REGIONAL	(For		)
		ON: Switches to another station only in the specific region using the “AF” control. ;
		OFF: Cancels.
	AF SET	(For		)
		ON: Automatically searches for another station broadcasting the same program in the same
		Radio Data System network with better reception when the current reception is poor. ;
		OFF: Cancels.
	TI	ON: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up). ;
		OFF: Cancels.
	PTY SEARCH	Selects the available Program Type (see the following), then, press S / T to start.
CLOCK
	TIME SYNC	ON: Synchronizes the unit’s time to the Radio Data System or Radio Broadcast Data System
		station time. ; OFF: Cancels.

•[MONO SET]/ [NEWS SET]/ [REGIONAL]/ [AF SET]/ [TI]/ [PTY SEARCH] is selectable only when the band is FM1/ FM2/ FM3.

•Available Program Type:

(For / / )

SPEECH : NEWS, INFORM (information), SPORTS, TALK, LANGUAGE, REL TALK (religious talk), PERSNLTY

(personality), PUBLIC, COLLEGE, HABL ESP (spanish talk), WEATHER

MUSIC : ROCK, CLS ROCK (classic rock), ADLT HIT (adult hits),

SOFT RCK (softrock), TOP 40, COUNTRY, OLDIES, SOFT,

NOSTALGA (nostalgia), JAZZ, CLASSICL (classical), R & B (rhythm and blues), SOFT R&B (soft rhythm and blues), REL MUSC (religious music), MUSC ESP (spanish music), HIP HOP

(For )

SPEECH : NEWS, AFFAIRS, INFO (information), SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

MUSIC : POP M (music), ROCK M (music), EASY M (music),

LIGHT M (music), CLASSICS, OTHER M (music), JAZZ,

COUNTRY, NATION M (music), OLDIES, FOLK M (music) The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.

•If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

6

CD / USB / iPod / ANDROID

Start playback

The source changes automatically and playback starts.

M Eject disc

Label side

USB input terminal

USB

CA-U1EX (max.: 500 mA) (optional accessory)

iPod/iPhone

KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2

ANDROID*3

Micro USB 2.0 cable*2 (commercially available)

*1 KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type *2 Do not leave the cable inside the car when not

using.

To		On the faceplate					On the remote control
Playback / pause	*4	Press	.				Press	.
Reverse / Fast-forward		Press and hold		S	/	T	Press and hold		S	/	.
						.
Select a track/file		Press S / T.					Press S /		.
Select a folder*5		Press J / K.					Press	/			.

Repeat play*6 Press repeatedly.

	TRACK REPEAT/ REPEAT OFF			: Audio CD
	FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF : MP3/WMA/AAC/WAV file, iPod or
				ANDROID
	FILE REPEAT/ REPEAT OFF			: KME Light/ KMC file*7
Random play*6	Press	repeatedly.
	DISC RANDOM/ RANDOM OFF			: Audio CD
	FOLDER RANDOM/ RANDOM OFF : MP3/WMA/AAC/WAV file, KME Light/ KMC
				file, iPod or ANDROID
	Press and hold		to select ALL RANDOM.*8
Select control mode	While in iPod source, press			repeatedly.
	MODE ON : Control from the iPod*9
	MODE OFF : Control from the unit

While in ANDROID source, (8, [ANDROID SETUP])

Select music drive	Press	repeatedly.
( 8, [MUSIC DRIVE])	The stored songs in the following start playback.

•Selected internal or external memory of a smartphone (Mass Storage Class).

•Selected drive of a multiple drives device.

ENGLISH 7

CD / USB / iPod / ANDROID

*3	When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is
	shown. Follow the instructions to install the application. You can also install the latest version
*4	of KENWOOD MUSIC PLAY application on your Android device before connecting. ( 22)
	For ANDROID: Applicable only when [BROWSE MODE] is selected. ( [ANDROID SETUP])
*5	For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.
*6	For iPod/ ANDROID: Applicable only when [MODE OFF]/ [BROWSE MODE] is selected.
*7	KME Light : KENWOOD Music Editor Light, KMC : KENWOOD Music Control ( 21)
*8	For CD: Only for MP3/WMA/AAC files.
*9	You can still play/pause, file skip, fast-forward or reverse files from the unit.
Select a file from a folder/list
1	Press	.
2	Turn the volume knob to select a folder/list, then press the knob.
3	Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

For USB (for KME Light/ KMC files):

Press S / T to search at a preset skip search ratio. ([SKIP SEARCH]) Press and hold S / T to search at a 10% ratio.

• Not applicable for CD and MP3/WMA/AAC/WAV files.

For iPod:

You can search for a file according to the first character.

Turn the volume knob quickly to enter character search.

Turn the volume knob to select the character.

To search for a character other than A to Z and 0 to 9, enter only “*”. Press S / T to move to the entry position.

• You can enter up to 3 characters.

Press the volume knob to start searching.

•To return to the root folder/ first file/ top menu, press .

•To return to the previous setting item, press .

•To cancel, press and hold .

•For iPod, applicable only when [MODE OFF] is selected. ( 7)

•For ANDROID, applicable only when [BROWSE MODE] is selected. ( [ANDROID SETUP])

Direct Music Search (using RC-406) (except for )

1 Press DIRECT.

2 Press the number buttons to enter a track/file number. 3 Press to search for music.

•To cancel, press or DIRECT.

•Not available if Random Play is selected.

•Not applicable for iPod, ANDROID, KME Light/ KMC file.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Other settings

1 Press the volume knob to enter [FUNCTION].

2Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default: XX

ANDROID SETUP

BROWSE MODE: Control from the unit (using KENWOOD MUSIC PLAY application). ; HAND MODE: Control other media player applications from the Android device (without using KENWOOD MUSIC PLAY application). However, you can still play/pause and file skip from the unit.

USB

	MUSIC DRIVE	DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 5]) is selected
		automatically and playback starts.
		Repeat steps 1 to 3 to select the following drives.
	SKIP SEARCH	0.5%/ 1%/ 5%/ 10%: While listening to iPod, ANDROID or KME
		Light/ KMC file, selects the skip search ratio over the total files.

8

Pandora® (except for )

Preparation:

Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.

• Select [ON] for [PANDORA SRC]. (5)

Start listening

1 Open the Pandora application on your device.

2Connect your device to the USB input terminal.

USB input terminal

KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2

The source changes to PANDORA and broadcast starts.

To		On the faceplate			On the remote control
Playback / pause		Press	.		Press	.
Skip a track		Press T.			Press	.
Thumbs up or thumbs		Press	/	.	Press	/	.
down*3
*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.
*3	If thumbs down is selected, the current track is skipped.

Create and save a new station

1 Press and hold the volume knob.

2Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.

A new station is created based on the current song or artist.

3 Press and hold one of the number buttons (1 to 5) to store.

To select a stored station, press one of the number buttons (1 to 5).

Search for a registered station

1 Press

.

2Turn the volume knob to make a selection, then press the knob.

[BY DATE]: According to the registered date

[A-Z]: Alphabetical order

3 Turn the volume knob to the desired station, then press the knob.

To cancel, press and hold . (or using RC-406)

Press J/ K to search for a station, then press .

Bookmark a song or artist information

1 Press and hold J.

2Turn the volume knob to make a selection, then press the knob.

[THIS TRACK]: Current song information [THIS ARTIST]: Current artist information

“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.

ENGLISH 9