80168610
Edition 2 December 2009
Air Die Grinder
3101G and 3107G
Product Information
EN Product Information
ES Especificaciones del producto
FR Spécifications du produit
Save These Instructions
|
|
|
PMAX |
9 |
3 |
2 |
|
|
|
|
|
6 |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
8h |
10 |
48h |
|
1 |
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
PMAX |
|
4 |
|
|
|
|
|
|
6 |
|
8 |
24h |
|
|
|
|
|
|
|
7 |
5 |
|
|
|
|
|
|
|
|
|
|
|
(Dwg. 16573164) |
|
|
|
|
|
|
||
1 |
2 |
3 |
5 |
6 |
7 |
9 |
10 |
|
|
|
|||||||
IR # - NPT |
inch (mm) |
NPT |
IR # |
IR # |
IR # |
cm3 |
||
C38121-600-VS |
3/8 (10) |
1/4 |
MSCF32 |
10 |
67 |
2 |
||
80168610_ed2
EN
Product Safety Information
Intended Use:
These die grinders are designed for grinding, porting, polishing, de-burring, and breaking sharp edges.
For additional information refer to Air Die Grinder Product Safety Information Manual Form 04580288.
Manuals can be downloaded from www.ingersollrandproducts.com.
Product Specifications
Model |
Exhaust |
Collet Size |
Free Speed |
|
Rated Power |
|
Tool Weight |
Overall Length |
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
rpm |
|
|
hp |
|
kW |
|
lbs |
|
Kg |
in |
|
mm |
|
3101G |
|
Rear |
1/4” |
|
|
20000 |
|
0.33 |
|
0.25 |
|
1.3 |
|
0.58 |
|
6.8 |
|
171.0 |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3107G |
|
Rear |
1/4” |
|
|
27000 |
|
0.33 |
|
0.25 |
|
1.0 |
|
0.45 |
|
6.6 |
|
168.0 |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
|
Average Air |
|
Air Consumption |
|
|
Sound Level dB (A) |
|
Vibration Level |
|||||||||||||
Model |
|
Consumption |
|
|
|
@ Load |
|
|
|
(ISO15744) |
|
(ISO8662) |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
cfm |
|
l/min |
|
cfm |
|
l/min |
|
† Pressure (L ) |
‡ Power (L ) |
|
|
m/s2 |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
p |
|
|
w |
|
|
|
|
|
3101G |
|
3 |
|
85 |
|
18 |
|
500 |
|
|
|
93.1 |
|
|
104.1 |
|
|
1.8 |
|||||
3107G |
|
3 |
|
85 |
|
18 |
|
500 |
|
|
|
92.4 |
|
|
103.4 |
|
|
2.6 |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
† KpA |
= 3dB measurement uncertanity |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
‡ KwA |
= 3dB measurement uncertanity |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
Installation and Lubrication
Size air supply line to ensure tool’s maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping, air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 16573164 and table on page 2. Maintenance frequency is shown in
circular arrow and defined as h=hours, d=days, and m=months of actual use. Items identified as:
1. |
Air filter |
6. |
Thread size |
2. |
Regulator |
7. |
Coupling |
3. |
Lubricator |
8. |
Safety Air Fuse |
4. |
Emergency shut-off valve |
9. |
Oil |
5. |
Hose diameter |
10. |
Grease - through fitting |
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that they can be recycled.
The original language of this manual is English.
Tool repair and maintenance should only be carried out by an authorized Service Center. Refer all communications to the nearest Ingersoll Rand Office or Distributor.
80168610_ed2 |
EN- |
Loading...