Huawei E960 User Manual 2

HUAWEI E960 HSDPA Wireless Gateway Quick Start

The HUAWEI E960 supports HSDPA/WCDMA 2100, GSM/GPRS/EDGE 1900/1800/900/850, and network auto-switch. With the E960, you can experience wireless gateway and USB modem at any time and any place.

E960 Appearance

Power	WLAN Signal
		Reset
Interface Ethernet Phone
Power	ON/OFF	Mode

yPower Interface: When connected with the power adapter, the E960 functions as a wireless gateway. When connected to the PC with a USB data cable, the E960 functions as a USB modem.

yEthernet: Insert a Ethernet cable connected to the PC or other network equipments.

yPhone: Insert a phone cable connected with a telephone to realize the voice service.

yPower: Power indicator. When it is in yellow, the charge is finished.

yWLAN: WLAN indicator. If it is steady on and in yellow, the WLAN is enabled. If it is blinking, data is transmitting.

yON/ OFF: Press and hold to power on or off the E960.

ySignal: Signal strength indicator. The following table shows the status of the signal strength indicator:

Status	Description	Status	Description
Fast blinking in	No SIM card or unverified	Steady on in	Signal strength in level
red	PIN code	yellow	two or three (middle)
Steady on in red	Signal strength in level	Steady on in	Signal strength in level
	one (weak)	green	four or five (strong)

yMode: The network mode indicator. The following table shows the status of the network mode indicator:

Status	Description	Status	Description
Double blinking	Searching the network or	Blinking in	Normal GPRS/EDGE
in green	no network	blue	network
Steady on and	GPRS/EDGE data service	Fast blinking	Downloading the
in green	connected	in green	upgrade mode
Blinking in blue	Normal WCDMA network	Indicator off	Off
Steady on in	WCDMA data service	Steady on in	HSDPA data service
blue	connected	cyan	connected

yReset: Reset button. On the side of the E960. Press and hold it for more than five seconds to restore the factory defaults.

PC Configuration Requirements

The recommended PC configurations for using the E960 are as follows:

yCPU: Pentium 500 MHz or above

yMemory: 128 MB RAM or above

yHard disk: 50 MB available space

yOperating System: Windows 2000, Windows XP, or Windows Vista

yLCD resolution: 800*600 or above, recommended 1024*768.

yInterface: standard USB interface

yInternet Explorer: IE6.0 or above, Firefox 1.5 or above, Netscape 8.0 or above

Note: If the configurations of the PC are lower than the recommended, the performance of the E960 may be weakened.

1

Step 1: Insert the SIM Card

Insert the SIM card into the socket with the golden contact facing upward. Insert the card socket into the E960.

2

3

4

Step 2: Install the

Power Adapter

Step 3: Connect to the PC

Step 4: Connect to the Telephone

Plug in the USB end of the power adapter to the power interface of the E960, and plug in the power plug to the power socket. Please use the E960 compatible power adapter; otherwise, the E960 can be damaged.

The Ethernet cable cannot be longer than 100 meters. For better effect, please use the shielded cable.

The telephone cable cannot be longer than three meters, and the telephone can be connected with three extensions.

Step 5: Log in to the Wireless Gateway Web Management

1.Open the Internet Explorer, and then enter the default web address (192.168.1.1) of the E960 in the address bar.

2.In the WIRELESS GATEWAY LOGIN page, select the user type, enter the password, and then click.

Admin: Have the rights the view and modify the configurations, and the default password is admin;

User: Only view the basic information, and the default password is user.

Only one user can log in to the E960 management page at one time, which is to prevent the configuration conflict.

3.If you are prompted to enter the PIN code, you need to enter the correct PIN code, and then click .

Note:

yIf the correct PIN code or PUK code is invalid, you cannot use the network-related services.

yPlease consult your service provider about whether to use SIM/USIM card.

yYour service provider provides the SIM/USIM card. For more information about SIM/USIM card, please consult your service provider.

Step 6: Making the First Call