Huawei HG630V2 User Manual

HG630 V2 Home Gateway

Quick Start

1 Connecting Cables

Installing the HG630 V2 on a DSL Broadband Network

In some communities, Internet service providers use telephone lines to provide broadband access services.

If you have subscribed to digital subscriber line (DSL) broadband, you can connect the HG630 V2 to a telephone port for Internet access.

Follow the steps in the following figure to connect devices properly.

4

10

9 5

1

8

a

c

2 b

3

1	Telephone wall jack	2 Splitter	3 Telephone

1

4	HG630 V2	5	Power adapter	6	Desktop computer
7	Set-top Box	8	Laptop computer	9	Smart Phone
10	Pad
a	LINE port	b PHONE port		c MODEM port

When configuring the HG630 V2 for the first time, use an Ethernet cable to connect the HG630 V2 to a computer

2 Powering On

To power on the HG630 V2, press its power button.

After the HG630 V2 is powered on, the HG630 V2 indicator turns on. The following table lists how the indicators behave when the HG630 V2 is operating correctly. If the indicators do not behave as expected, ensure that everything is plugged in correctly.

	Indicator	Expected State	Description
	Power	Steady on	The HG630 V2 is powered on.
		Steady on	A digital subscriber line (DSL) connection
	WAN		has been set up and activated.
		Blinking	A DSL connection is being activated.
			The HG630 V2 is connected to the Internet
		Steady on	in router mode, but no data is being
	Internet		transmitted.
			The HG630 V2 is connected to the Internet
		Blinking	in router mode, and data is being
			transmitted.

2

	Indicator	Expected State	Description
		Steady on	The HG630 V2 has WLAN enabled, but is
			not transmitting data.
	WLAN
		Blinking	The HG630 V2 has WLAN enabled, and
			data is being transmitted.
			The HG630 V2 is connected to a wireless
			client, such as a computer with a wireless
		Steady on	network adapter, over the WLAN using the
			Wi-Fi Protected Setup (WPS) function.
	WPS		The WPS indicator is steady on for 300
			seconds.
			The HG630 V2 is attempting to connect to a
		Blinking	wireless client over the WLAN using the
			WPS function.
			The LAN port is connected to an Ethernet
		Steady on	device (such as a computer) with a network
	LAN1 LAN4		cable, but no data is being transmitted.
			The LAN port is connected to an Ethernet
		Blinking	device with a network cable, and data is
			being transmitted.
		Steady on	The HG630 V2 is connected to a USB
			device, but no data is being transmitted.
	USB
		Blinking	The HG630 V2 is connected to a USB
			device, and data is being transmitted.

3

3 Setting the Computer IP Address

Before logging in to the HG630 V2 web management page, set the IP address of the computer that will be used for the login.

On Windows 7

1.Click in the lower right corner of your desktop. Choose Open Network and Sharing Center.

2.Choose Change adapter settings. Right-click Local Area Connection and choose Properties.

3.Double-click Internet Protocol Version 4 (TCP/IPv4).

4.Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK.

4 Setting Network Access Parameters

Configuring an Automatical Connection to Access the Internet

The HG630 V2 supports you to choose the proper connection mode automatically to access the Internet, meaning you do not need to install dial-up software or perform dial-up operations on your computer and just following the wizard page.

To set up an automatical connection to access the Internet:

1.Open a browser on your computer. In the address box, enter 192.168.1.1. Press Enter to access the web management page.

2.On the login page, enter the login user name (user by default) and password (HuaweiUser by default). Click Log in.

>To protect against unauthorized access, change the user name and password after the first login.

>You can change the account parameters on Maintain > Account Management page.

4