Yaskawa P1000 User Manual

0 (0)

Step

P1000 Model

Identification and Mounting

Connect Motor and

Line Power

Step

The following

procedure is a

supplement to

other

documentation

supplied with this

equipment and will

guide the user in

properly wiring the

P1000 and motor.

It will also show

the user how to

configure the

P1000 for a

general purpose

application.

DANGER!

Improper wiring

can and will cause

bodily harm as well

as damage to the

equipment.

When installing the

system, be sure to

follow good wiring

practices and all

applicable codes.

Ensure that the

mounting of

components is

secure and that the

environment, such

as extreme

dampness, poor

ventilation, etc. will

not cause system

degradation.

Please read this

cheat sheet and

other

documentation

provided with the

P1000 thoroughly

before attemp

ting

any installation.

Page 1 of 2

WARNING DO NOT CONNECT ANY OF THE

FOLLOWING TERMINALS TO EARTH GROUND

B1 B2

+1 +2 +3

NOT USED

Fig.1 & 2

below show the electrical connections for the

input power and motor terminals for various P1000 models.

Select the proper diagram for the model you are installing

(see Step 1).

WITH POWER OFF

make the appropriate

connections.

Make sure to follow good wiring practices and all applicable

codes. Ensure that the equipment is grou

nded properly as

shown in fig. 1

DANGER;

LETHAL VOLTAGES ARE PRESENT- Before

applying power to the P1000, ensure that the terminal cover

is fa

stened and all wiring connections are secure. After the

power has been turned OFF, wait at

least five minutes until

the charge indicator extinguishes completely

before touching

any wiring, circuit boards or components.

Make sure the P1000 has been properly sized for single phase input

power. For best performance, the drive input supply voltage must be

equal to or greater than the motor rated voltage.

3Ø Induction

motor

Connect

frame to

ground

Input

Protection

(Fuse or Circuit

Breaker)

To change direction of motor

rotation swap any

two

of the

three

motor leads.

Fig. 2 Input Power and Output Motor Electrical Connections for

Models: 2_0110 & Lar

ger and 4_0058 & Larger

(R/L1) (S/L2)

(T/L3)

(U/T1)

(V/T2)

(W/T3)

Connect to

chassis

ground

Use L1, L2, L3 for

3Ø Input Power

Use L1, L2 for

1Ø Input Power

BUS TERMINALS:

DO NOT CONNECT TO GROUND

Use L1, L2, L3 for

3Ø Input Power

To change

direction of

motor rotation

swap any

two

of the

three

motor leads.

Fig. 1 Input Power and Output Motor Electrical Connections for

Models: 2_0004 - 2_0056, 4_0002 - 4_00

44 and 5_0003 - 50011

Use L1, L2 for

1Ø Input Power

3Ø Induction

motor

Connect

frame to

ground

Input

Protection

(Fuse or Circuit

Breaker)

(R/L1)

(S/L2)

(T/L3)

(U/T1)

(V/T2)

(W/T3)

Connect to chassis

ground

DC Bus terminals

location varies by

model.

To make sure you received the correct model, it is essential to

verify the P1000 nameplate with your

order and make sure the

P1000 has the correct rating so it can be used with your motor.

Please check

the nameplate information as shown in the

example below.

· Check that the available power will meet the

input power

requirements.

· Ensure that the

output power

from the P1000 is

compatible with the motor requirements.

Mounting the P1000

· In the case of systems with more than one P1000, follow

the above procedure for each P1000 and motor.

The mounting of the P1000 is extremely important regarding

environment and accessibility. Depending on your system,

there are various models available and the mounting

dimensions (footprint) may be different. Because the

mounting procedure is fairly extensive, it is beyond the scope

of this document; the user is referred to the P1000 Quick

Start Guide (

Document No. TOEP YAIP1U 01

) received with the

P1000,

Section 2.2, Mechanical Installation

. Match the model

that you received and follow the procedure described in the

manual to ensure a safe and functional installation. In cases

where the system has more than one P1000, refer to the

proper clearances required for adequate ventilation.

Please

pay particular attention to:

· The clearances to be maintained around the enclosure

for adequate ventilation.

· The environmental specifications such as avoiding

excessive dampness, extreme temperatures, chemical

exposure, corrosive areas, etc. to avoid damage to the

equipment and to maintain safety.

Removing and Attaching the Terminal Cover

Improper removal of the P1000 terminal cover as well as front

cover can cause extensive damage to the P1000. To avoid

damage to these items, please pay particular attention to the

P1000 Quick Start Guide,

Document No. TOEP YAIP1U 01

Section 3.5, Removing and Attaching the Terminal Cover

Open Chassis

NEMA 1

Drive Model

Number

Input Power

Rating

Output Power

Rating

Serial

Number

UL File

Number

Drive Spec Number

Weight

Software

Version

Normal

Duty Amps

CIMR-PU2A0021FAA

CC :

8500

6W3050 - 2 - 100

J0073D207410100

This step shows how to setup the sequence and reference method of the P1000. The

sequence method determines how the P1000 drive receives its start and stop command

and the reference method determines how the speed of the motor is controlled. Make sure

all protective covers have been re-attached and power is turned on.

. DO NOT RUN THE

MOTOR

This section may require you to change one or more P1000 parameters. Please

refer to Step 5 for a det

ailed explanation on how to change parameters.

SELECT START / STOP CONTROL METHOD

Start / Stop Control from Digital Operator

Go to parameter b1-02, set value to

b1-02

Start / Stop Control from external terminals (switch or relay contact)

Go to parameter b1-02, set value to

( Factory Default)

NOTE: It is beyond the scope of this document to program the P1000 drive for network communication control.

Please refer to the

refer to the P1000 Technical Manual, (Document No. SIEP YAIP1U 01)

for this selection.

SELECT SPEED METHOD

b1-01

(Factory Default)

Adjust motor speed / frequency from the Digital Operator

Go to parameter b1-01, set value to

Adjust motor speed / frequency from external terminals (0 - 10V / 4 - 20mA Signal)

Go to parameter b1-01, set value to

(Factory Default)

Jumper located

inside the drive on

the terminal board

To adjust frequency use / and press .

+V AC A1 A2 A3 FM AM AC RP AC

Potentiometer

2K Ohm

Speed Potentiometer

24V

0 – 10V Connection

0 ~ 10Vdc

4 ~ 20mA

Note: 2

row of terminal board is shown here.

Wiring Diagram: 2-Wire Control

Forward

Reverse

Wiring Diagram: 3-Wire Control

Use for momentary contacts

Use for maintained contacts

User Terminals User Terminals

(Set Parameter A1-03 to 3330)

Note: 3

row of terminal board is shown here.

Link

Start

Switch

Reverse

Stop

Switch

Normally

Open

Normally

Closed

Link

+V AC A1 A2 A3 FM AM AC RP AC

24V

+V AC A1 A2 A3 FM AM AC RP AC

24V

0 – 20mA / 4- 20mA Connection

Brown or Red: +Power (1)

Black: Output

4 – 20mA (2)

Cable

Shield

+V AC A1 A2 A3 FM AM AC RP AC

24V

2-Wire, 4-20mA Transducer

Cable

Type

DIN

Type

Cable

Shield

E(G)

Cable

Shield

S1 S2 S3 S4 S5 S6 S7 S8 SN SC

Install link (AC-SN) when

using transducer.

A1 A3

Selecting Start/Stop and Speed Method

Real-time

Clock Setup

This step shows how to setup the

P1000 real-time clock for first

use.

Power up the drive and set the

real-time Clock. The real-time

Clock setup screen will appears

at first power up.

Note:

after the real-time clock is

set this screen will not show

again unless parameter o4-17 is

set to “Set”.

Real-time Clock Setup Screen

Press to select the digit

you would like to change and

use to adjust.

When date and time are set

press to save.

IMPORTANT

If no key is pressed within 30

sec. the operator will revert

back to the main menu

showing a

“TIM” alarm

(Alarm not set).

To set the real-time clock

again disconnect and

reconnect the operator.

Note:

Do NOT adjust sec per

month.

Example:

Jun 2

2012, 3:30pm

P1000 AC Drive

Quick Start Procedure

+ 1 hidden pages