SLV-E850B/E850UX/E880EG/F900B/F900NP/F900UX/ F900VC/F990B/F990NP/F990UX/F990VC
RMT-V222C/V222D/V222E/V223C/V240/V240A/V240B/V240C/V240D
French Model
SLV-E850B/F900B/F990B
SERVICE MANUAL
UK Model
SLV-E850UX/F900UX/F990UX
Greek Model
SLV-E880EG
Spanish Model
SLV-F900NP/F990NP
German Model
SLV-F900VC/F990VC
SUPPLEMENT-1
File this supplement with the service manual.
(99-017)
Subject: EEP ROM INITIAL DATA INPUT
1. EEP ROM INITIAL DATA INPUT
When EEP ROM (IC182 on FR-128 board) was changed, make it sure to input the data shown below and to perform “2-3-1. RF Switching Position/AF Switching Position Adjustment ”.
Input Method:
1)Connect the LANC jig (J-6090-051-A) to CN165 on MA-316 board.
2)Turn on the power.
3)Input Data: 80 in Address: 01 on Page: 00.
4)Input data on Page F as following table.
5)Turn off the power
|
Page |
|
|
|
|
|
F |
|
|
|
|
|
|
Address |
01 |
02 |
0A |
0B |
0C |
0D |
B4 |
BA |
BB |
BC |
BD |
|
SLV-E850B |
03 |
01 |
B5 |
CE |
20 |
02 |
25 |
10 |
E1 |
00 |
10 |
|
SLV-E850UX |
03 |
03 |
85 |
CE |
20 |
02 |
15 |
10 |
E1 |
00 |
10 |
|
SLV-E880EG |
05 |
0C |
85 |
CE |
20 |
06 |
20 |
10 |
E0 |
00 |
10 |
|
SLV-F900B |
0E |
05 |
B5 |
CE |
20 |
02 |
25 |
10 |
E1 |
00 |
10 |
|
SLV-F900NP |
0E |
06 |
85 |
CE |
20 |
02 |
20 |
10 |
E1 |
00 |
10 |
Data |
SLV-F900UX |
0E |
07 |
85 |
CE |
20 |
02 |
15 |
10 |
E1 |
00 |
10 |
|
SLV-F900VC |
0E |
04 |
85 |
CE |
20 |
02 |
20 |
10 |
E0 |
00 |
10 |
|
SLV-F990B |
0E |
09 |
B5 |
CE |
20 |
02 |
25 |
10 |
E1 |
00 |
10 |
|
SLV-F990NP |
0E |
0A |
85 |
CE |
20 |
06 |
20 |
10 |
E1 |
00 |
10 |
|
SLV-F990UX |
0E |
0B |
85 |
CE |
20 |
06 |
15 |
10 |
E1 |
00 |
10 |
|
SLV-F990VC |
0E |
08 |
85 |
CE |
20 |
06 |
20 |
10 |
E0 |
00 |
10 |
6)Disconnect the adjusting remote commander and LANC jig from the connector (CN165).
Note: When connecting or disconnecting LANC jig to CN165 on MA-316 board, first connect the adjusting remote commander (J-6082-053-B) to the jack on LANC jig before connecting LANC jig to CN165. Connection or disconnection of the adjusting remote commander in the condition LANC jig is connected to CN165 causes IC LINK (PS001) to damage itself.
Sony Corporation
99I0562-1 Printed in Japan © 1999. 9
9-921-688-81 |
Home Video Company |
Published by Quality Assurance Dept. |