DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM MX-4112N / MX-5112N
QUICK START GUIDE
Keep this manual close at hand for reference whenever needed.
For the users of the fax function
Important safety instructions
•If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network.
•Never install telephone wiring during a lightning storm.
•Never install telephone jacks in wet locations unless the socket is specifically designed for wet locations.
•Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
•Do not use a telephone to report a gas leak in the vicinity of the leak.
•Do not install or use the machine near water, or when you are wet. Take care not to spill any liquids on the machine.
•Save these instructions.
2
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
The equipment should be installed near an accessible socket outlet for easy disconnection. Each instruction also covers the optional units used with these products.
3
FAX interface cable and Line cable
These special accessories must be used with the device.
The declaration of conformity may be consulted at: http://www.sharp.de/doc/MX-FX11.pdf
Notice for users in the UK
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or 
and of the same rating as the one removed from the plug must be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live
As the colours of the wires in this mains lead may not correspond with coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E, or by the safety earth symbol 
, or coloured green or greenand-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
EMC (this machine and peripheral devices)
Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Peripheral devices are described in the [PERIPHERAL DEVICE] in the Operation Guide.
This machine contains the software having modules developed by Independent JPEG Group.
This product includes Adobe® Flash® technology of Adobe Systems Incorporated.
Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved.
4
SOFTWARE LICENCE
The SOFTWARE LICENCE will appear when you install the software from the CD-ROM. By using all or any portion of the software on the CD-ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENCE.
The explanations in this manual are based on American English and the North American version of the software.
Software for other countries and regions may vary slightly from the North American version.
•The explanations in this manual assume that you have a working knowledge of your Windows or Macintosh computer.
•For information on your operating system, please refer to your operating system manual or the online Help function.
•The explanations of screens and procedures in this manual are primarily for Windows Vista® in Windows® environments. The screens may vary depending on the version of the operating system.
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your dealer or nearest authorised service representative.
•This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest authorised service representative.
•Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due to use of the product.
Products that have earned the ENERGY STAR® are designed to protect the environment through superior energy efficiency.
The products that meet the ENERGY STAR® guidelines carry the logo shown above. The products without the logo may not meet the ENERGY STAR® guidelines.
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2010. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws.
MATERIAL SAFETY DATA SHEET
The MSDS (Material Safety Data Sheet) can be viewed at the following URL address: http://www.sharp-world.com/corporate/info/index.html
5
Contents
OPERATION MANUALS AND HOW TO USE THEM —————————— 7
CAUTIONS — ——————————————————————————— 8
Symbols in this manual — ——————————————————————— 8 Power notes — ———————————————————————————— 8 Installation notes — —————————————————————————— 9 About consumables —————————————————————————— 10 Handling precautions — ———————————————————————— 10
NAMES OF PARTS AND COMPONENTS,
TURNING ON THE POWER ——————————————————— 12
HOME SCREEN ————————————————————————— 13
For operating the touch panel and functions the icon.
OVERVIEW OF COPY OPERATION ———————————————— 14
OVERVIEW OF OTHER OPERATIONS —————————————— 16
For functions other than copy.
MAINTENANCE ————————————————————————— 17 SPECIFICATIONS ———————————————————————— 18 SUPPLIES — —————————————————————————— 23
OTHERS — ——————————————————————————— 24
TO THE ADMINISTRATOR OF THE MACHINE — —————————— 25
INFORMATION ON DISPOSAL — ————————————————— 26
TRADEMARK ACKNOWLEDGMENTS ——————————————— 27
6
OPERATION MANUALS AND HOW TO USE THEM
Quick Start Guide (this document)
Features important safety notes, names of parts and components, information about the power-on procedure, operation overviews, information for people who manage the machine, and information about other aspects of this machine.
Read this section before using the machine for the first time.
Operation Guide (PC)
Can be downloaded from the machine to a computer and viewed. Refer to this document to learn more about printer mode and settings mode, and to learn about the details of each type of mode.
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
MX-4112N / MX-5112N
QUICK START GUIDE
Keep this manual close at hand for reference whenever needed.
MX-4112N / MX-5112N
Software Setup Guide (CD-PDF)
Explains how to install the various drivers needed when using this machine as a printer, network scanner, or fax machine. Refer to this document when using this machine from a computer. The Software Setup Guide can be found on the “Software CD-ROM”.
Operation Guide (Built-in)
Can be viewed by touching the operation guide icon on the machine’s touch panel. When you are using this machine, use this document to see an overview of a particular mode or when you are having trouble operating the machine.
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM |
Software Setup Guide |
BEFORE INSTALLING THE SOFTWARE |
SETUP IN A WINDOWS ENVIRONMENT |
SETUP IN A MACINTOSH ENVIRONMENT |
TROUBLESHOOTING |
Common operations |
|
Operation Guide Index |
|
Home screen |
Preview screen |
How to set the |
Text entry |
original and |
|||
|
|
paper |
|
By mode |
|
|
|
Copier |
Facsimile |
Image send |
Document |
filing |
|||
Others |
|
|
|
Eco |
Maintenance |
Troubleshooting |
Appendix |
To close Operation Guiude, tap [close] key or press Home button.
Downloading the Operation Guide (PC)
You can download the [Operation Guide (PC)] by following the procedures below while the machine is connected to the network.
1Confirm the machine’s IP address
First, tap the [Settings] key on the home screen, and then tap [System Settings] → [List Print (User)] in the left menu.
Next, tap the [Print] key in the [All Custom Setting List], and confirm the IP address in the printed list.
2Insert the machine’s IP address into the address bar of your web browser to access the machine.
http://machine’s IP address/ User verification may be required
depending on the machine’s settings. Please check with the machine’s administrator to obtain the account information necessary for verification.
3Download the [Operation Guide (PC)]
Click [Download Operation Guide] on the displayed page. Next, select the desired language from the “Language to download” list, and then click the [Download] button.
4Double-click on the downloaded file to display the Operation Guide (PC).
7
CAUTIONS
Symbols in this manual
To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are classified as explained below. Be sure you understand the meaning of the symbols when reading the manual.
WARNING |
CAUTION |
Indicates a risk of death or serious injury. |
Indicates a risk of human injury or property damage. |
|
CAUTION! |
PINCH POINT |
PROHIBITED |
DO NOT |
MANDATORY |
|
Meaning of the symbols |
||||||
HOT |
KEEP CLEAR |
ACTIONS |
DISASSEMBLE |
ACTIONS |
||
|
Power notes
WARNING
Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. Do not use an extension cord or adapter to connect other devices to the power outlet used by the machine. Using an improper power supply may cause fire or electrical shock.
*For the power supply requirements, see the name plate in the lower left corner of the left side of the machine.
Do not damage or modify the power cord.
Placing heavy objects on the power cord, pulling it, or forcibly bending it will damage the cord, resulting in fire or electrical shock.
Do not insert or remove the power plug with wet hands.
This may cause electrical shock.
CAUTION
When removing the power plug from the outlet, do not pull on the cord.
Pulling on the cord may cause damage such as wire exposure and breakage, and may result in fire or electrical shock.
If you will not use the machine for a long time, be sure to remove the power plug from the outlet for safety.
When moving the machine, switch off the main power and remove the power plug from the outlet before moving.
The cord may be damaged, creating a risk of fire or electrical shock.
8
Installation notes
CAUTION
Do not install the machine on an unstable or slanted surface. Install the machine on a surface that can withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
If peripheral devices are to be installed, do not install on an uneven floor, slanted surface, or otherwise unstable surface. Danger of slippage, falling, and toppling. Install the product on a flat, stable surface that can withstand the weight of the product.
Do not install in a location with moisture or dust.
Risk of fire and electrical shock.
If dust enters the machine, dirty output and machine failure may result.
Locations that are excessively hot, cold, humid, or dry (near heaters, humidifiers, air conditioners, etc.)
The paper will become damp and condensation may form inside the machine, causing misfeeds and dirty output. 
SPECIFICATIONS (page 18)
If the location has an ultrasonic humidifier, use pure water for humidifiers in the humidifier. If tap water is used, minerals and other impurities will be emitted, causing impurities to collect on the inside of the machine and create dirty output.
When the machine is installed, the adjusters (5) must be lowered to the floor to secure the machine (prevent it from moving).
Rotate the adjusters in the locking direction until they are in firm contact with the floor.
If you find it necessary to reposition the machine due to |
Lock |
Release |
rearrangement of your office layout or other reason, retract the |
|
|
adjusters from the floor, turn off the power, and then move the |
|
|
machine. |
|
|
(After moving the machine, lower the adjusters again to secure the machine.)
Locations exposed to direct sunlight
Plastic parts may become deformed and dirty output may result.
Locations with ammonia gas
Installing the machine next to a diazo copy machine may cause dirty output.
Do not install the machine in a location with poor air circulation.
A small amount of ozone is created inside the machine during printing. The amount of ozone created is not sufficient to be harmful; however, an unpleasant odor may be noticed during large copy runs, and thus the machine should be installed in a room with a ventilation fan or windows that provide sufficient air circulation. (The odor may occasionally cause headaches.)
* Install the machine so that people are not directly exposed to exhaust from the machine. If installed near a window, ensure that the machine is not exposed to direct sunlight.
Near a wall
Be sure to allow the required space around the machine for |
|
30 cm |
|
|
|
servicing and proper ventilation. (The machine should be no |
|
|
closer than the distances indicated below from walls. The |
|
|
indicated distances are for the case when a saddle finisher and |
30 cm |
45 cm |
large capacity paper tray are not installed.) |
Locations subject to vibration.
Vibration may cause failure.
CAUTION
The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In particular, never move the machine while the power is on.
•The machine should be installed near an accessible power outlet for easy connection.
•Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.
9
Loading...