KDC-X398
KDC-358U
KMR-D358
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space
provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X398/ KDC-358U/ KMR-D358 Serial number
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
© 2013 JVC KENWOOD Corporation |
GET0964-001B (KW/K0) |
CONTENTS
BEFORE USE |
2 |
BASICS |
3 |
GETTING STARTED |
4 |
RADIO |
5 |
CD / USB / iPod |
6 |
AUX |
8 |
Pandora® |
8 |
iHeartRadio® |
9 |
SiriusXM® Radio |
10 |
AUDIO SETTINGS |
12 |
DISPLAY SETTINGS |
13 |
MORE INFORMATION |
13 |
TROUBLESHOOTING |
14 |
INSTALLATION / |
|
CONNECTION |
16 |
SPECIFICATIONS |
i and ii |
(at the end of the book)
How to read this manual
•Operations are explained mainly using buttons on the faceplate.
•[XX] indicates the selected items.
•(BXX) indicates references are available on the stated page.
BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
•Adjust the volume so that you can hear sounds outside the car to prevent accidents.
•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•Avoid using the USB device or iPod/iPhone if it might hinder safe driving.
•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
•Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
•If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RC-406):
•Do not leave the remote control in hot places such as on the dashboard.
•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
•Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.
Handling discs:
•Do not touch the recording surface of the disc.
•Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
•Do not use any accessories for the disc.
•Clean from the center of the disc and move outward.
•Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
•When removing discs from this unit, pull them out horizontally.
•Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse side of the faceplate)
2
BASICS |
|
|
Faceplate |
Remote control (RC-406) |
|
Volume knob |
(not supplied for KMR-D358 ) |
|
(turn/press) |
Display window |
Remote sensor (Do not expose |
|
|
|
|
|
to bright sunlight.) |
|
|
Pull out the |
|
* Not used. |
insulation sheet |
|
when using for the |
|
Detach button |
|
first time. |
|
|
Attach |
Detach |
How to reset |
How to replace the battery |
|
|
|
Your preset |
|
|
|
adjustments will also |
|
|
|
be erased. |
To |
Do this (on the faceplate) |
Do this (on the remote control) |
Turn on the power |
Press L SRC. |
Press and hold SRC to turn off the power. |
|
• Press and hold to turn off the power.* |
( Pressing SRC does not turn on the power. ) |
|
|
|
Adjust the volume |
Turn the volume knob. |
Press VOL or VOL . |
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Select a source |
Press L SRC repeatedly. |
Press SRC repeatedly. |
|
Change the display |
Press DISP SCRL repeatedly. |
( not available ) |
|
information |
• Press and hold to scroll the current display information. |
||
|
* For KMR-D358 : The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off).
ENGLISH | 3
GETTING STARTED
1Cancel the demonstration
When you turn on the power (or after you reset the unit), the display shows: “CANCEL DEMO” B “PRESS” B “VOLUME KNOB”
1Press the volume knob.
[YES] is selected for the initial setup.
2Press the volume knob again.
“DEMO OFF” appears.
For KMR-D358 , [DEMO OFF] is selected initially.
2Set the clock
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [CLOCK], then press the knob.
3Turn the volume knob to select [CLOCK ADJUST], then press the knob.
4Turn the volume knob to make the settings, then press the knob.
Day B Hour B Minute
5Turn the volume knob to select [CLOCK FORMAT], then press the knob.
6Turn the volume knob to select [12H] or [24H], then press the knob.
7 Press and hold to exit.
To return to the previous setting item or hierarchy, press .
3Set the initial settings
1 Press SRC to enter STANDBY.
2 Press the volume knob to enter [FUNCTION].
3Turn the volume knob to make a selection (see the following table), then press the knob.
4 Press and hold to exit.
To return to the previous setting item or hierarchy, press .
|
|
Default: XX |
AUDIO CONTROL |
|
|
SP SELECT |
OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches or |
|
|
|
4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum performance. |
DISPLAY |
|
|
EASY MENU |
ON: Both display and button illumination change to white color when entering |
|
|
|
[FUNCTION]. ; OFF: Both display and button illumination remain as [COLOR |
|
|
SELECT] color. (B13) |
TUNER SETTING |
|
|
PRESET TYPE |
NORMAL: Memorizes one station for each preset button in each band (FM1/ |
|
|
|
FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel for each |
|
|
preset button, regardless of the selected band or SiriusXM channel. |
SYSTEM |
|
|
KEY BEEP |
ON: Activates the keypress tone. ; OFF: Deactivates. |
|
SOURCE SELECT |
|
|
|
PANDORA SRC |
ON: Enables PANDORA in source selection. ; OFF: Disables. (B8) |
|
IHEART SRC |
ON: Enables IHEARTRADIO in source selection. ; OFF: Disables. (B9) |
|
BUILT-IN AUX |
ON: Enables AUX in source selection. ; OFF: Disables. (B8) |
CD READ |
1: Automatically distinguishes between audio file disc and music CD. ; 2: Forces |
|
|
|
to play as an music CD. No sound can be heard if an audio file disc is played. |
F/W UPDATE
UPDATE SYSTEM
F/W UP xx.xx YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated). For details on how to update the firmware, see: www.kenwood.com/cs/ce/
4
RADIO
Search for a station
1 Press L SRC to select TUNER.
2Press JBAND repeatedly (or press *AM– / #FM+ on RC-406) to select FM1/ FM2/ FM3/ AM.
3Press S/ T(or press S/ T(+) on RC-406) to search for a station.
•To change the searching method for S/ T: Press
KSEEK repeatedly.
AUTO1: Automatically search for a station. AUTO2: Automatically search for a preset station. MANUAL: Manually search for a station.
•To store a station: Press and hold one of the number buttons (1 to 6).
•To select a stored station: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).
Direct Access Tuning (using RC-406)
(except for KMR-D358 )
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press ENT IWto search for a station.
•To cancel, press or DIRECT.
•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.
Other settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to make a selection (see the following table), then press the knob.
3 Press and hold to exit.
To return to the previous setting item or hierarchy, press .
Default: XX
TUNER SETTING
AUTO |
YES: Automatically starts memorizing 6 stations with good reception. ; NO: Cancels. |
MEMORY |
(Selectable only if [NORMAL] is selected for [PRESET TYPE].) (B4) |
MONO SET |
ON: Improves the FM reception, but the stereo effect may be lost. ; OFF: Cancels. |
TI |
ON: Allows the unit to temporarily switch to Traffic Information. ; OFF: Cancels. |
PTY SEARCH |
Selects the available Program Type (see below), then, press S/ Tto start. |
CLOCK |
|
TIME SYNC |
ON: Synchronizes the unit’s time to the Radio Broadcast Data System station time. ; |
|
OFF: Cancels. |
•[MONO SET]/ [TI]/ [PTY SEARCH] is selectable only when the band is FM1/ FM2/ FM3.
•Available Program Type:
SPEECH: NEWS, INFORM (information), SPORTS, TALK, LANGUAGE, REL TALK (religious talk), PERSNLTY (personality), PUBLIC, COLLEGE, HABL ESP (spanish talk), WEATHER
MUSIC: ROCK, CLS ROCK (classic rock), ADLT HIT (adult hits), SOFT RCK (softrock), TOP 40,
COUNTRY, OLDIES, SOFT, NOSTALGA (nostalgia), JAZZ, CLASSICL (classical), R & B (rhythm and blues), SOFT R&B (soft rhythm and blues), REL MUSC (religious music), MUSC ESP (spanish music), HIP HOP
The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.
•If the volume is adjusted during reception of traffic information or alarm, the adjusted volume is memorized automatically. It will be applied the next time traffic information or alarm function is turned on.
ENGLISH | 5
CD / USB / iPod
Start playback
The source changes automatically and playback starts.
CD
|
|
|
|
Label side |
M: Eject disc |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
USB
USB input terminal
CA-U1EX (max.: 500 mA) (optional accessory)
iPod/iPhone
USB input terminal
KCA-iP102 (optional accessory)
Press and hold iPod to select the control mode while in iPod source.
MODE ON: From the iPod*1. MODE OFF: From the unit.
To |
Do this |
Pause or resume |
Press 6 IW(or press ENT IWon RC-406). |
playback |
|
Select a track/file |
Press S/ T(or press S/ T(+) on RC-406). |
|
|
Select a folder *2 |
Press J/ K(or press *AM– / #FM+ on RC-406). |
Reverse/ |
Press and hold S/ T(or press and hold S/ T(+) on RC-406). |
Fast-forward |
|
Repeat play *3 |
Press 4 repeatedly. |
•Audio CD: TRACK REPEAT, REPEAT OFF
•MP3/WMA/WAV file or iPod: FILE REPEAT, FOLDER REPEAT, REPEAT OFF
•KENWOOD Music Editor Light (KME Light)/ KENWOOD Music Control (KMC) file (B13): FILE REPEAT, REPEAT OFF
Random play *3 |
Press 3 repeatedly. |
•Audio CD: DISC RANDOM, RANDOM OFF
•MP3/WMA/WAV file or iPod or KME Light/ KMC file: FOLDER RANDOM, RANDOM OFF
Press and hold 3to select “ALL RANDOM”. *4
*1 You can still play/pause, file search, fast-forward or reverse files from the unit. *2 Only for MP3/WMA/WAV files. This does not work for iPod.
*3 For iPod: Applicable only when [MODE OFF] is selected. *4 For CD: Only for MP3/WMA files.
If you connect the iPod/iPhone to the USB input terminal of the unit (while listening to TuneIn, TuneIn Radio Pro or Aupeo), the unit will output the sound from these apps.
6
CD / USB / iPod
Select a track/file from a list
For iPod: Applicable only when [MODE OFF] is selected. (B6)
1 Press .
2Turn the volume knob to make a selection, then press the knob.
•MP3/WMA/WAV file: Select the desired folder, then a file.
•iPod or KME Light/ KMC file: Select the desired file from the list (PLAYLISTS, ARTISTS, ALBUMS, SONGS, PODCASTS*, GENRES, COMPOSERS*).
*Only for iPod.
•To return to the root folder (or first file), press number button 5.
•To return to the previous setting item or hierarchy, press .
•To cancel, press and hold .
If you have many files....
You can search through them quickly (on step 2
above) at a preset skip search ratio by pressing
S/ T.
•See also “Set the skip search ratio.”
•Pressing and holding S/ Tskip songs at the maximum ratio (10%) regardless of the setting made.
•For USB: Only for files registered in the database created with KME Light/ KMC.
•Not applicable for audio CD.
Direct Music Search (using RC-406)
(except for KMR-D358 )
1 Press DIRECT.
2Press the number buttons to enter a track/ file number.
3 Press ENT IWto search for music.
•To cancel, press .
•Not available if Random Play is selected.
•Not applicable for iPod, KME Light/ KMC file.
Select a song by name
While listening to iPod...
1 Press |
. |
2Turn the volume knob to select a category, then press the knob.
3Turn the volume knob quickly to enter character search.
4Turn the volume knob to select the character to be searched for.
5Press S/ Tto move to the entry position.
You can enter up to 3 characters.
6 Press the volume knob to start searching.
7Turn the volume knob to make a selection, then press the knob.
Repeat step 7 until the desired item is selected.
•To search for a character other than A to Z and 0 to 9, enter only “*”.
•To return to the previous hierarchy, press .
•To return to the top menu, press number button 5.
•To cancel, press and hold .
Set the skip search ratio
While listening to iPod or KME Light/ KMC file...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [USB], then press the knob.
3Turn the volume knob to select [SKIP SEARCH], then press the knob.
4Turn the volume knob to make a selection, then press the knob.
0.5% (default)/ 1%/ 5%/ 10%: Skip search ratio over the total files.
5 Press and hold to exit.
Change the USB drive
When a smartphone (Mass Storage Class) is connected to the USB input terminal, you can select its internal memory or external memory (such as an SD card) to playback the stored songs. You can also select the desired drive to playback when a multiple drives device is connected.
Press number button 5 repeatedly to select the desired drive.
(or)
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [USB], then press the knob.
3 Turn the volume knob to select [MUSIC DRIVE], then press the knob.
4Press the volume knob to select
[DRIVE CHANGE].
The next drive is selected automatically.
Repeat steps 1 to 4 to select the following drives.
Selectable items: [DRIVE 1] to [DRIVE 5]
ENGLISH | 7
AUX
Preparation:
Select [ON] for [BUILT-IN AUX]. (B4)
Start listening
1Connect a portable audio player (commercially available).
Auxiliary input jack
Portable audio 3.5 mm (1/8") stereo mini plug with player
“L” shaped connector (commercially available)
2 Press SRC to select AUX.
3Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [SYSTEM], then press the knob.
3Turn the volume knob to select [AUX NAME SET], then press the knob.
4Turn the volume knob to make a selection, then press the knob.
AUX (default)/ DVD/ PORTABLE/ GAME/ VIDEO/ TV
5 Press and hold to exit.
Pandora®
Preparation:
Install the latest version of the Pandora application onto your device (iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [ON] for [PANDORA SRC]. (B4)
Start listening
1Open the Pandora application on your device.
2Connect your device to the USB input terminal.
USB input terminal
KCA-iP102 (optional accessory)
The source changes to PANDORA and broadcast starts.
To |
|
Do this |
|
Pause or resume |
|
Press 6 IW(or press ENT IW |
|
playback |
|
on RC-406). |
|
|
|
|
|
Thumbs up or |
|
Press J |
/ K . |
thumbs down |
• If thumbs down is selected, the |
||
|
|
current track is skipped. |
|
|
|
|
|
Skip a track |
|
Press T(or press T(+) on |
|
|
|
RC-406). |
|
Create a new |
1 Press and hold the volume |
||
station |
|
knob. |
|
|
2 Turn the volume knob to |
||
|
|
select [FROM TRACK] or [FROM |
|
|
|
ARTIST], then press the knob. |
|
|
|
A new station is created based |
|
|
|
on the current song or artist. |
|
Save a station |
|
Press and hold one of the |
|
|
|
number buttons (1 to 5) to |
|
|
|
store. |
|
|
• |
To select a stored station, press |
|
|
|
one of the number buttons |
|
|
|
(1 to 5). |
|
|
|
|
|
Search for a |
1 |
Press |
. |
registered |
2 Turn the volume knob to |
||
station |
|
make a selection, then press |
|
|
|
the knob (or press J/Kon |
|
|
|
RC-406). |
|
[BY DATE]: According to the registered date.
[A-Z]: Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
8
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for KENWOOD application onto your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio
• Select [ON] for [IHEART SRC]. (B4)
Start listening
1Open the iHeart Link application on your device.
2Connect your device to the USB input terminal.
USB input terminal
KCA-iP102 (optional accessory)
3Press L SRC to select IHEARTRADIO.
Broadcast starts automatically.
To |
Do this |
Pause or |
Press 6 IW(or press |
resume |
ENT IWon RC-406). |
playback |
|
Thumbs up or |
Press J / K . |
thumbs down |
• If thumbs down is selected, |
for custom |
the current track is skipped. |
station |
|
Skip a track for |
Press T(or press T(+) |
custom station |
on RC-406). |
|
|
Create a new/ |
Press 1. |
custom station |
|
Add to favorite |
Press 2. |
stations for live |
|
station |
|
|
|
Scan for live |
Press 5. |
station |
|
Search for a station
1 Press .
2Turn the volume knob to select a category, then press the knob.
3Turn the volume knob to the desired station, then press the knob.
When a city list appears, you can skip cites in alphabetical order.
(or using RC-406)
Press J/ Kto search for a station.
• To cancel, press and hold .
Skip cities by alphabetical order
While a city list appears during search...
1Turn the volume knob quickly to enter character search.
2Turn the volume knob or press S/ T to select the character to be searched for.
3Press J/ Kto move to the previous/next page.
4 Press the volume knob to start searching.
• To cancel, press and hold .
Delete a station
While listening to IHEARTRADIO...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [SYSTEM], then press the knob.
3Turn the volume knob to select [STATION DELETE], then press the knob.
4Turn the volume knob to select [LIVE] or [CUSTOM], then press the knob.
5Turn the volume knob to select the desired station to delete, then press the knob.
6Turn the volume knob to select [YES], then press the knob.
7 Press and hold to exit.
To return to the previous setting item or hierarchy, press .
ENGLISH | 9
SiriusXM® Radio
Preparation:
1Connect the optional SiriusXM Vehicle Tuner (commercially available).
Antenna
Expansion port on |
SiriusXM Vehicle Tuner |
the rear panel |
|
2Activate the subscription through www.siriusxm.com/activatenow or call 1-866-635-2349.
The Radio ID is required to activate the SiriusXM Vehicle Tuner. The Radio ID is located on the label of the SiriusXM Vehicle Tuner
and can also be shown on the unit’s display window when you select “Channel 0” after SiriusXM Vehicle Tuner is connected.
For users in Canada: To activate SiriusXM Canada service go to www.xmradio.ca and click on “ACTIVATE RADIO” in the top right corner, or call 1-877-438-9677.
3 Press L SRC to select SIRIUS XM to start updating.
Start listening
1 |
Press L SRC to select SIRIUS XM. |
|
2 |
Press JBAND repeatedly to select a band. |
|
3 |
Press |
. |
4Turn the volume knob to select a category, then press the knob.
If “ALL CHANNELS” is selected, all the available channels will be shown.
5Turn the volume knob to select a channel, then press the knob.
(or)
Press S/ Tto search for a channel manually.
• Pressing and holding S/ Tchanges the channel rapidly.
If a locked channel or a mature channel ([MATURE CH] is set to [ON]) is selected, a pass code input screen appears. Enter the pass code to receive the channel.
•To change the tuning method for S/ T: Press KSEEK.
Each time you press KSEEK, the tuning method switches between “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).
•To store a channel of the current band: Press and hold one of the number buttons (1 to 6).
•To select a stored channel of the current band: Press one of the number buttons (1 to 6).
Direct Access Tuning (using RC-406)
(except for KMR-D358 )
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a channel number. 3 Press S/ T(+) to start searching.
•To cancel, press or DIRECT.
•If no operation is done for 10 seconds after step 3, Direct Access Tuning is automatically canceled.
SiriusXM Replay™
Press and hold KSEEK (or Kon RC-406).
Replay starts from the live position and “” lights up.
During Replay...
•To pause or resume playback, press 6 IW(or ENT IWon RC-406).
•To skip the current song backward/forward, press S/ T(or S/ T(+) on RC-406).
•To rewind/fast-forward, press and hold S/ T(or S/ T(+) on RC-406).
•To exit from Replay and go to live, press and hold KSEEK (or Kon RC-406).
10
SiriusXM® Radio
Smart Favorites
User stored channels (1 to 6) are recognized as Smart Favorite channels. SiriusXM Vehicle Tuner automatically buffered their broadcasting content in the background.
•Smart Favorite channel is available with SXV200 or later SiriusXM tuner models.
When you select a Smart Favorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
1Press one of the number buttons (1 to 6) to select a channel.
2 For operation (B10, SiriusXM Replay™)
SiriusXM settings
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [SIRIUS XM], then press the knob.
3 Turn the volume knob to make a selection (see the following table), then press the knob. 4 Press and holdto exit.
Default: XX
There are two types of lock functions available:
•SiriusXM-defined: When [MATURE CH] is set to [ON]
•User-defined: Using [CHANNEL EDIT] when [MATURE CH] is set to [OFF]
CHANNEL LOCK |
To unlock settings: |
||
|
|
1 |
Turn the volume knob to select a number. |
|
|
2 |
Press S/ Tto move to the entry position. |
|
|
3 |
Repeat steps 1 and 2 to enter the current pass code. (Initial pass code is 0000.) |
|
|
4 |
Press the volume knob to confirm. |
|
CODE SET |
1 Turn the volume knob to select a number. |
|
|
|
2 |
Press S/ Tto move to the entry position. |
|
|
3 |
Repeat steps 1 and 2 to enter a new 4-digit pass code. |
|
|
4 |
Press the volume knob to confirm. |
|
|
5 |
Repeat steps 1 to 4 to reconfirm the pass code. |
|
|
• Make a note of the new pass code to enter channel lock settings from next time. |
|
|
CHANNEL EDIT * |
1 Turn the volume knob to select a category, then press the knob. |
2Turn the volume knob to select a channel you want to lock, then press the knob. “L” appears in front of the channel number.
3 Press and hold to exit.
CHANNEL CLEAR* YES: Clears all the locked channels. ; NO: Cancels.
MATURE CH |
ON: Turns on the SiriusXM-defined lock setting (mature channel). ; OFF: Turns off. |
|
• If [ON] is selected, your setting [CHANNEL EDIT] is temporary ignored. |
SIGNAL LEVEL |
WEAK/ GOOD/ STRONG: Shows the strength of the current received signal. |
|
|
BUFFER USAGE |
0% — 100% (0): Shows the memory usage for Replay buffer. |
|
|
SXM RESET |
YES: Resets stored channel, locked channel setting and Mature CH setting to default. ; NO: Cancels. |
* Displayed only when [MATURE CH] is set to [OFF].
ENGLISH | 11
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [AUDIO CONTROL], then press the knob.
3Turn the volume knob to make a selection (see the following table), then press the knob.
Repeat step 3 until the desired item is selected or activated.
4 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [AUDIO CONTROL].
2 Press J/Kto make a selection, then press ENT IW.
To return to the previous setting item or hierarchy, press .
|
|
|
|
|
Default: XX |
|
SUB-W LEVEL |
–15 to +15 (0): |
Adjusts the subwoofer output level. |
||||
|
|
|
|
|
|
|
BASS LEVEL |
–8 to +8 (+6): |
Adjusts the level to memorize for each source. (Before |
||||
|
|
|
|
|
||
MID LEVEL |
–8 to +8 (+5): |
making an adjustment, select the source you want to |
||||
|
|
|
|
|
adjust.) |
|
TRE LEVEL |
–8 to +8 (0): |
|||||
|
||||||
|
|
|
|
|
||
EQ PRO (for |
|
) |
|
|||
KDC-X398 |
|
|||||
|
|
|
|
|
|
|
|
BASS ADJUST |
BASS CTR FRQ |
60/ 80/ 100/ 200HZ: Selects the center frequency. |
|||
|
|
|
|
|
|
|
|
|
|
BASS LEVEL |
–8 to +8 (+6): Adjusts the level. |
||
|
|
|
|
|
|
|
|
|
|
BASS Q FACTOR |
1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor. |
||
|
|
|
|
|
|
|
|
|
|
BASS EXTEND |
ON: Turns on the extended bass. ; OFF: Cancels. |
||
|
|
|
|
|
|
|
|
MID ADJUST |
MID CTR FRQ |
0.5/ 1.0/ 1.5/ 2.5KHZ: Selects the center frequency. |
|||
|
|
|
|
|
|
|
|
|
|
MID LEVEL |
–8 to +8 (+5): Adjusts the level. |
||
|
|
|
|
|
|
|
|
|
|
MID Q FACTOR |
0.75/ 1.00/ 1.25: Adjusts the quality factor. |
||
|
|
|
|
|
|
|
|
TRE ADJUST |
TRE CTR FRQ |
10.0/ 12.5/ 15.0/ 17.5KHZ: Selects the center frequency. |
|||
|
|
|
|
|
|
|
|
|
|
TRE LEVEL |
–8 to +8 (0): Adjusts the level. |
||
|
|
|
|
|
|
PRESET EQ |
DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/ |
|
NATURAL/ USER: Selects a preset equalizer suitable to the music |
|
genre. (Select [USER] to use the customized bass, middle, and treble |
|
settings.) |
|
[DRIVE EQ] is a preset equalizer that reduces noise from the road. |
|
|
BASS BOOST |
LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred bass boost level. ; |
|
OFF: Cancels. |
|
|
LOUDNESS |
LEVEL1/ LEVEL2: Selects your preferred low and high frequencies |
|
boost to produce a well-balanced sound at a low volume level. ; |
|
OFF: Cancels. |
|
|
SUBWOOFER SET |
ON: Turns on the subwoofer output. ; OFF: Cancels. |
|
|
LPF SUBWOOFER |
THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ |
|
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/ |
|
160 Hz are sent to the subwoofer. |
|
|
SUB-W PHASE |
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer |
|
output to be in line with the speaker output for optimum performance. |
|
(Selectable only if a setting other than [THROUGH] is selected for |
|
[LPF SUBWOOFER].) |
HPF |
THROUGH: All signals are sent to the speakers. ; 100HZ/ 120HZ/ |
|
150HZ: Audio signals with frequencies higher than 100 Hz/ 120 Hz/ |
|
150 Hz are sent to the speakers. |
|
|
FADER |
R15 to F15 (0): Adjusts the rear and front speaker output balance. |
|
|
BALANCE |
L15 to R15 (0): Adjusts the left and right speaker output balance. |
|
|
VOLUME OFFSET |
–8 to +8 (for AUX) ; –8 to 0 (for other sources): Presets the volume |
(Default: 0) |
adjustment level of each source. (Before adjustment, select the source |
|
you want to adjust.) |
|
|
SOUND RECNSTR |
ON: Creates realistic sound by compensating the high-frequency |
(Sound |
components and restoring the rise-time of the waveform that are lost |
reconstruction) |
in audio data compression. ; OFF: Cancels. |
|
|
[SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON].
12
DISPLAY SETTINGS
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [DISPLAY], then press the knob.
3Turn the volume knob to make a selection (see the following table), then press the knob.
Repeat step 3 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item or hierarchy, press .
Default: XX
COLOR SELECT VARIABLE SCAN/ COLOR 01 — COLOR 24/
USER: Selects your preferred key illumination color.
You can create your own color (when
[COLOR 01] — [COLOR 24] or [USER] is selected). The color you have created can be selected when you select [USER].
1Press and hold the volume knob to enter the detailed color adjustment.
2Press S/ Tto select the color (R/ G/ B) to adjust.
3Turn the volume knob to adjust the level (0 — 9), then press the knob.
DIMMER |
ON: Dims the display and button illumination. ; |
|
OFF: Illuminates according to the |
|
[BRIGHTNESS] settings. |
|
|
BRIGHTNESS |
0 — 31: Selects your preferred brightness |
|
level for display and button illumination. |
|
|
TEXT SCROLL |
AUTO/ ONCE: Selects whether to scroll the |
|
display information automatically, or scroll |
|
only once. ; OFF: Cancels. |
MORE INFORMATION
General
•This unit can only play the following CDs:
•Detailed information and notes about the playable audio files are stated in an online manual on the following web site: www.kenwood.com/cs/ce/audiofile/
Playable files
•Playable audio file: MP3 (.mp3), WMA (.wma)
•Playable disc media: CD-R/CD-RW/CD-ROM
•Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
•Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.
Unplayable discs
•Discs that are not round.
•Discs with coloring on the recording surface or discs that are dirty.
•Recordable/ReWritable discs that have not been finalized.
•8 cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
•This unit can play MP3/WMA/WAV files stored on a USB mass storage class device.
•You cannot connect a USB device via a USB hub.
•Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
•This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1 A.
About KENWOOD Music Editor Light
and KENWOOD Music Control
•This unit supports the PC application KENWOOD Music Editor Light and Android™ application KENWOOD Music Control.
•When you play audio files with song data added using the KENWOOD Music Editor Light or KENWOOD Music Control, you can search for audio files by Genres, Artists, Albums, Playlists, and Songs.
•KENWOOD Music Editor Light and KENWOOD Music Control are available on the following web site: www.kenwood.com/cs/ce/
About iPod/iPhone
Made for
-iPod touch (1st, 2nd, 3rd, 4th, and 5th generation)
-iPod classic
-iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
-iPhone, iPhone 3G, 3GS, 4, 4S, 5
•For the latest compatible list and software versions of iPhone/iPod, see: www.kenwood.com/cs/ce/ipod
•To connect devices featuring Lightning connector, both KCA-iP102 (optional accessory) and Apple Lightning to 30-pin Adapter (accessory of the iPod/iPhone) are required.
Do not leave the Apple Lightning to 30-pin Adapter inside the car to prevent damages caused by the hot temperature.
•You cannot operate iPod if “KENWOOD” or “” is displayed on iPod.
ENGLISH | 13
MORE INFORMATION
About Pandora
•Pandora is available only in the U.S., Australia and New Zealand.
•Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
•Some functions of Pandora cannot be operated from this unit.
•For issues using the application, please contact Pandora at pandora-support@pandora.com.
•If the version of the OS of the connected iPhone is earlier than 4.0, start the Pandora application before selecting the PANDORA source.
About iHeartRadio
•iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
•Some iHeartRadio® functionality cannot be operated from this unit.
Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial telephone accessory.
(B17)
When a call comes in, “CALL” appears.
(The audio system pauses.)
•To continue listening to the audio system during a call, press SRC. “CALL” disappears and the audio system resumes.
When the call ends, “CALL” disappears.
(The audio system resumes.)
TROUBLESHOOTING
Symptom |
|
Remedy |
||
Sound cannot be heard. |
• |
Adjust the volume to the optimum level. |
||
|
|
|
• Check the cords and connections. |
|
“PROTECT” appears and no operations |
|
Check to be sure the terminals of the speaker wires are insulated properly, then reset |
||
can be done. |
|
the unit. If this does not solve the problem, consult your nearest service center. |
||
• Sound cannot be heard. |
|
Clean the connectors. (B2) |
||
• The unit does not turn on. |
|
|
||
• Information shown on the display is |
|
|
||
incorrect. |
|
|
||
The unit does not work at all. |
|
Reset the unit. (B3) |
||
For |
|
: |
|
Make sure [OFF] is selected for [DEMO MODE]. (B4) |
KMR-D358 |
|
|||
The Auto Power Off function (that turns |
|
|
||
the power off after 20 minutes when in |
|
|
||
standby mode) does not work. |
|
|
||
• Radio reception is poor. |
• |
Connect the antenna firmly. |
||
• Static noise while listening to the radio. |
• |
Pull the antenna out all the way. |
||
“NA FILE” appears. |
|
Make sure the disc contains supported audio files. (B13) |
||
|
|
|
|
|
“NO DISC” appears. |
|
Insert a playable disc into the loading slot. |
||
“TOC ERROR” appears. |
|
Make sure the disc is clean and inserted properly. |
||
“PLEASE EJECT” appears. |
|
Reset the unit. If this does not solve the problem, consult your nearest service center. |
||
Disc cannot be ejected. |
|
Press and hold Mto forcibly eject the disc. Be careful not to drop the disc when it is |
||
|
|
|
|
ejected. If this does not solve the problem, reset the unit. (B3) |
“READ ERROR” appears. |
|
Copy the files and folders onto the USB device again. If this does not solve the |
||
|
|
|
|
problem, reset the USB device or use another USB device. |
“NO DEVICE” appears. |
|
Connect a USB device, and change the source to USB again. |
||
“COPY PRO” appears. |
|
A copy-protected file is played. |
||
“NA DEVICE” appears. |
|
Connect a supported USB device, and check the connections. |
||
“NO MUSIC” appears. |
|
Connect a USB device that contains playable audio files. |
||
“iPod ERROR” appears. |
• |
Reconnect the iPod. |
||
|
|
|
• |
Reset the iPod. |
14
TROUBLESHOOTING
Symptom |
Remedy |
|
Noise is generated. |
Skip to another track or change the disc. |
|
|
|
|
Tracks do not play back as you |
Playback order is determined when files are recorded. |
|
intended them to play. |
|
|
“READING” keeps flashing. |
Do not use too many hierarchical levels or folders. |
|
|
|
|
Elapsed playing time is not |
This is caused by how the tracks are recorded. |
|
correct. |
|
|
Correct characters are not |
This unit can only display uppercase letters, numbers, and |
|
displayed (e.g. album name). |
a limited number of symbols. |
|
|
“ADD ERROR” |
New station creation is unsuccessful. |
|
“SEARCH ERROR” |
|
|
“CHECK DEVICE” |
Check the Pandora application on your device. |
|
“NO SKIPS” |
The skip limit has been reached. |
|
“NO STATIONS” |
No stations are found. |
Pandora |
“STATION LIMIT” |
The number of registered stations has reached its limit. |
|
Retry after deleting unnecessary stations from your device. |
|
|
|
|
|
“UPGRADE APP” |
Make sure you have installed the latest version of the |
|
|
Pandora application on your device. |
|
“CONNECT ERROR” |
Communication is unstable. |
|
“RATING ERROR” |
Registration of thumbs up/thumbs down has failed. |
|
“LICENSE ERROR” |
You try to access from a country which Pandora is not |
|
|
deliverable. |
|
Station cannot be |
If “Explicit Content” in [Account Settings] is checked in |
iHeartRadio |
selected. |
the web version of iHeartRADIO, custom stations become |
|
unavailable. |
|
|
|
|
|
“CANNOT CREATE” |
Custom station name creation is unsuccessful. |
|
“CANNOT SAVE” |
Addition to the favorite category failed. |
|
“DISCONNECTED” |
Check the connection to the device. |
Symptom |
Remedy |
||
|
“NO SKIPS” |
The skip limit has been reached. Retry later. |
|
|
“NO STATIONS” |
No stations are found. |
|
|
“NOT CONNECTED” |
Link to the application is impossible. |
|
|
“IHEARTLINK UP” |
Make sure you have installed the latest version of the |
|
|
|
iHeart Link for KENWOOD application on your device. |
|
iHeartRadio |
AVAILABLE” |
You haven’t log in. Log in again. |
|
|
“PLEASE LOGIN” |
||
|
“STATION NOT |
Broadcast from the station is over. |
|
|
|
|
|
|
“STATION NOT |
No station is selected. |
|
|
SELECTED” |
|
|
|
“STREAM ERROR” |
Broadcast data is interrupted. |
|
|
“THUMB FAILED” |
Registration of Thumbs Up/Down has failed. |
|
|
“TIMED OUT” |
The request has resulted in time-out. |
|
|
“CH LOCKED” |
The selected channel is locked. Enter the correct pass code |
|
|
|
to unlock. (B11) |
|
|
“CHAN UNSUB” |
The selected channel is unsubscribed. |
|
|
|
Call 1-866-635-2349 or 1-877-438-9677 to subscribe. |
|
Radio |
“CH UNAVAIL” |
The selected channel is unavailable. |
|
“CHECK ANTENNA” |
Check the antenna and its connection are in good |
||
|
|||
SiriusXM® |
|
condition. |
|
“CHECK TUNER” |
unit. |
||
|
Make sure the SiriusXM Vehicle Tuner is connected to the |
||
|
“NO SIGNAL” |
Make sure the antenna is mounted outside the vehicle. |
|
|
“SUBSCRIPTION |
Your subscription is updated. Press the volume knob to |
|
|
UPDATED – PRESS |
continue. |
|
|
ENTER TO CONTINUE.” |
|
|
|
“WRONG CODE” |
Make sure you have entered the correct pass code. (B11) |
ENGLISH | 15
INSTALLATION / CONNECTION
Warning
•The unit can only be used with a 12 V DC power supply, negative ground.
•Disconnect the battery’s negative terminal before wiring and mounting.
•Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
•Insulate unconnected wires with vinyl tape to prevent a short circuit.
•Be sure to ground this unit to the car’s chassis again after installation.
Caution
•For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
•Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
•Do not connect the swires of speakers to the car chassis or Ground wire (black), or connect them in parallel.
•Mount the unit at an angle of less than 30º.
•If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the ignition key.
•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
•If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating.
Basic procedure
1Remove the key from the ignition switch, then disconnect the sterminal of the car battery.
2Connect the wires properly.
See Wiring connection. (B 17)
3Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the sterminal of the car battery.
5 Reset the unit. (B 3)
Installing the unit (in-dash mounting)
Hook on the top side
Orientate the trim plate as illustrated before fitting.
Do the required wiring.
(B17)
Dashboard of your car
Bend the appropriate tabs to hold the mounting sleeve firmly in place.
When installing without the mounting sleeve 1
2
Use only the specified screws. Using wrong screws might damage the unit.
How to remove the unit 1 Detach the faceplate.
2 Fit the catch pin on the extraction keys into the holes on both sides of the trim plate, then pull it out.
3 Insert the extraction keys deeply into the slots on each side, then follow the arrows as shown on the right.
16