Kenwood KDC-BT562U, KDC-X599, KMR-D562BT Manual [es]

0 (0)

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below.

Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model KDC-X599/ KDC-BT562U/ KMR-D562BT

Serial number

US Residents Only

KDC-X599

KDC-BT562U

KMR-D562BT

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications

to this equipment may cause harmful interference unless the modifications are expressly

approved in the instruction manual. The user could lose the authority to operate this

equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment may

cause harmful interference to radio communications, if it is not installed and used in

accordance with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de

la vida útil (aplicable a los países que hayan adoptado sistemas independientes de

recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no

podrán ser desechados como residuos domésticos. Los equipos eléctricos y

electrónicos al final de la vida útil, deberán ser reciclados en instalaciones

que puedan dar el tratamiento adecuado a estos productos y a sus

subproductos residuales correspondientes. Póngase en contacto con su

administración local para obtener información sobre el punto de recogida

más cercano. Un tratamiento correcto del reciclaje y la eliminación de

residuos ayuda a conservar los recursos y evita al mismo tiempo efectos

perjudiciales en la salud y el medio ambiente.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

In compliance with Federal Regulations, following are reproductions of labels on, or inside

the product relating to laser product safety.

JVC KENWOOD Corporation

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR

SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—

special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada

ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou

importador.

A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos

naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio

ambiente.

IC (Industry Canada) Notice

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

The term “IC: ” before the certification/ registration number only signifies that the Industry

Canada technical specification were met.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement

que les specifications techniques d’Industrie Canada ont été respectées.

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C

to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very

low levels of RF energy that it deemed to comply without maximum permissive exposure

evaluation (MPE). But it is desirable that it should be installed and operated keeping the

radiator at least 20cm or more away from person’s body (excluding extremities: hands,

wrists, feet and ankles).

Under Industry Canada regulations, this radio transmitter may only operate using an

antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry

Canada. To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more

than that necessary for successful communication.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées

pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences

radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui

est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant,

cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre

le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et

chevilles).

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé

pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son

gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Para cumplimiento de la COFETEL:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda

causar su operación no deseada”

CONTENTS BEFORE USE

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of

the output level.

General:

• Avoid using the external device if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded

data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short

circuit.

• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to

evaporate.

Remote control (RC-406):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or

equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used

batteries promptly. If swallowed, contact a physician immediately.

BEFORE USE 2

BASICS 3

GETTING STARTED 4

RADIO 5

CD / USB / iPod / ANDROID 6

Pandora® 8

iHeartRadio® 9

SiriusXM® Radio 10

AUX 12

BLUETOOTH® 13

AUDIO SETTINGS 19

DISPLAY SETTINGS 20

MORE INFORMATION 21

TROUBLESHOOTING 22

SPECIFICATIONS 24

INSTALLATION /

CONNECTION 26

How to read this manual

• Operations are explained mainly

using buttons on the faceplate.

• [

] indicates the selected items.

• (



) indicates references are

available on the stated page.

Maintenance

Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector: Detach the faceplate and clean the connector

gently with a cotton swab, being careful not to damage the connector.

Handling discs:

• Do not touch the recording surface of the disc.

• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move outward.

• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

• When removing discs from this unit, pull them out horizontally.

• Remove burrs from the center hole and disc edge before inserting a disc.

Connector (on the reverse

side of the faceplate)

BASICS

To On the faceplate On the remote control

Turn on the power

Press

• Press and hold to turn off the power.*

Press and hold SRC to turn off the power.

( Pressing SRC does not turn on the power. )

Adjust the volume Turn the volume knob. Press

or .

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Select a source

Press

repeatedly.

Press SRC repeatedly.

Change the display

information

Press

repeatedly.

• Press and hold to scroll the current display information.

( not available )

For : The power will automatically turn off after 20minutes when in standby mode (Auto Power Off).

Faceplate

How to resetAttach Detach

Remote control (RC-406) (

supplied for

)

Remote control functions are not available for

ENGLISH

Pull out the insulation

sheet when using for

the first time.

Your preset

adjustments will also

be erased.

How to replace the battery

Remote sensor (Do not expose

to bright sunlight.)

Volume knob

(turn/press)

Detach button

Display window

GETTING STARTED

Default:

AUDIO CONTROL

SP SELECT

OFF

5/4

6 × 9/6

OEM

: Selects according to the speaker size (5inches

or 4inches, 6×9inches or 6inches) or OEM speakers for optimum

performance.

DISPLAY

EASY MENU

:Both display and button illumination change to white color when

entering [

FUNCTION

].;

OFF

:Both display and button illumination

remain as [

COLOR



SELECT

] color. ( 

)

TUNER SETTING

PRESET TYPE

NORMAL

:Memorizes one station for each preset button in each band

(FM1/ FM2/ FM3/ AM).;

MIX

:Memorizes one station or SiriusXM channel

for each preset button, regardless of the selected band or SiriusXM

channel.

SYSTEM

KEY BEEP

:Activates the keypress tone.;

OFF

:Deactivates.

SOURCE SELECT

PANDORA SRC

:Enables PANDORA in source selection.;

OFF

:Disables. ( 

)

IHEART SRC ON

:Enables IHEARTRADIO in source selection.;

OFF

:Disables. ( 

)

BUILT-IN AUX ON

:Enables AUX in source selection.;

OFF

:Disables. ( 

)

CD READ 1

:Automatically distinguishes between audio file disc and music CD.;

:Forces to play as a music CD. No sound can be heard if an audio file

disc is played.

F/W UPDATE

UPDATE SYSTEM / UPDATE BT

F/W UP xx.xx

YES

:Starts upgrading the firmware.;

:Cancels (upgrading is not

activated).

For details on how to update the firmware, see:

www.kenwood.com/cs/ce/

CLOCK

CLOCK DISPLAY

:The clock time is shown on the display even when the unit is turned

off.;

OFF

:Cancels.

Cancel the demonstration (

for /

)

When you turn on the power (or after you reset the unit), the display

shows: “CANCELDEMO”

“PRESS” “VOLUMEKNOB”

1 Press the volume knob.

[

YES

] is selected for the initial setup.

2 Press the volume knob again.

“DEMOOFF” appears.

Set the clock

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select [

CLOCK

], then press the knob.

3 Turn the volume knob to select [

CLOCK ADJUST

], then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Day

Hour Minute

5 Turn the volume knob to select [

CLOCK FORMAT

], then press the knob.

6 Turn the volume knob to select [

12H

] or [

24H

], then press the knob.

7 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press to enter STANDBY.

2 Press the volume knob to enter [

FUNCTION

3 Turn the volume knob to make a selection (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated.

5 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

RADIO

Search for a station

Press repeatedly to select TUNER.

2 Press repeatedly (or press / on

RC-406) to select FM1/ FM2/ FM3/ AM.

3 Press S/T (or press S/ on RC-406) to

search for a station.

• To change the searching method for S/T: Press

repeatedly.

AUTO1 : Automatically search for a station.

AUTO2 : Search for a preset station.

MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number

buttons (1to6).

• To select a stored station: Press one of the number

buttons (1to6) (or press one of the number buttons

(1to6) on RC-406).

Direct Access Tuning (using RC-406)

(

except for

)

Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a frequency.

3 Press to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step

2, Direct

Access Tuning is automatically canceled.

Other settings

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to make a selection (see the following table), then press

the knob.

3 Repeat step 2 until the desired item is selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

AUTO

MEMORY

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if [

NORMAL

] is selected for [

PRESET TYPE

]. ( 

)

MONO SET ON

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

TI ON

: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

OFF

: Cancels.

PTY SEARCH

Selects the available Program Type (see below), then, press

/

to start.

CLOCK

TIME SYNC

:Synchronizes the unit’s time to the Radio Broadcast Data System station time.;

OFF

:Cancels.

• [

MONO SET

]/ [

PTY SEARCH

] is selectable only when the band is FM1/ FM2/ FM3.

• Available Program Type:

SPEECH

NEWS

INFORM

(information),

SPORTS

TALK

LANGUAGE

REL TALK

(religious talk),

PERSNLTY

(personality),

PUBLIC

COLLEGE

HABL ESP

(spanish talk),

WEATHER

MUSIC

ROCK

CLS ROCK

(classic rock),

ADLT HIT

(adult hits),

SOFT RCK

(softrock),

TOP 40

COUNTRY

OLDIES

SOFT

NOSTALGA

(nostalgia),

JAZZ

CLASSICL

(classical),

R & B

(rhythm and blues),

SOFT R&B

(soft rhythm and blues),

REL MUSC

(religious

music),

MUSC ESP

(spanish music),

HIP HOP

The unit will search for the Program Type categorized under [

SPEECH

] or [

MUSIC

] if

selected.

• If the volume is adjusted during reception of traffic information, the adjusted volume

is memorized automatically. It will be applied the next time traffic information is

turned on.

CD / USB / iPod / ANDROID

Start playback

The source changes automatically and

playback starts.

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not

using.

To On the faceplate On the remote control

Playback / pause Press .

Press

Reverse / Fast-forward

Press and hold S/T. Press and hold S/ .

Select a track/file

Press S/T. Press S/

Select a folder

Press J/K.

Press

/ .

Repeat play

Press repeatedly.

TRACK REPEAT

REPEAT OFF

: Audio CD

FILE REPEAT

FOLDER REPEAT

REPEAT OFF

: MP3/WMA/AAC/WAV file, iPod or

ANDROID

FILE REPEAT

REPEAT OFF

: KME Light/ KMC file

Random play

Press repeatedly.

DISC RANDOM

RANDOM OFF

: Audio CD

FOLDER RANDOM

RANDOM OFF

: MP3/WMA/AAC/WAV file, KME Light/ KMC

file, iPod or ANDROID

Press and hold

to select

ALL RANDOM

Select control mode

While in iPod source, press

repeatedly.

MODE ON

: Control from the iPod

MODE OFF

: Control from the unit

While in ANDROID source,

(

, [

ANDROID SETUP

]

)

Select music drive

(

, [

MUSIC DRIVE

]

)

Press repeatedly.

The stored songs in the following start playback.

• Selected internal or external memory of a smartphone (Mass Storage

Class).

• Selected drive of a multiple drives device.

Label side

Eject disc

USB input terminal

CA-U1EX (max.: 500mA)

(optional accessory)

Micro USB 2.0 cable

(commercially available)

KCA-iP102 / KCA-iP103

(optional accessory)

or accessory cable of the

iPod/iPhone

USB

iPod/iPhone

ANDROID

ENGLISH

CD / USB / iPod / ANDROID

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is

shown. Follow the instructions to install the application. You can also install the latest version

of KENWOOD MUSIC PLAY application on your Android device before connecting. (



)

For ANDROID: Applicable only when [

BROWSE MODE

] is selected. ( [

ANDROID SETUP

])

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.

For iPod/ ANDROID: Applicable only when [

MODE OFF

]/ [

BROWSE MODE

] is selected.

KME Light : KENWOOD Music Editor Light, KMC : KENWOOD Music Control ( 

)

For CD: Only for MP3/WMA/AAC files.

You can still play/pause, file skip, fast-forward or reverse files from the unit.

Select a file from a folder/list

Press .

2 Turn the volume knob to select a folder/list, then press the knob.

3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

For USB (for KME Light/ KMC files):

Press S/T to search at a preset skip search ratio. (

[

SKIP SEARCH

])

Press and hold S/T to search at a 10

ratio.

• Not applicable for CD and MP3/WMA/AAC/WAV files.

For iPod:

You can search for a file according to the first character.

Turn the volume knob quickly to enter character search.

Turn the volume knob to select the character.

To search for a character other than A to Z and 0to9, enter only “

”.

Press S/T to move to the entry position.

• You can enter up to 3characters.

Press the volume knob to start searching.

• To return to the root folder/ first file/ top menu, press

• To return to the previous setting item, press

• To cancel, press and hold

• For iPod, applicable only when [

MODE OFF

] is selected. ( 

)

• For ANDROID, applicable only when [

BROWSE MODE

] is selected.

(

[

ANDROID SETUP

])

Direct Music Search (using RC-406) (

except for

)

Press DIRECT.

2 Press the number buttons to enter a track/file number.

3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPod, ANDROID, KME Light/ KMC file.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect

the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Other settings

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to make a selection (see the following

table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

ANDROID SETUP

BROWSE MODE

: Control from the unit (using KENWOOD MUSIC PLAY application).;

HAND MODE

:Control other media player applications from the Android device

(without using KENWOOD MUSIC PLAY application). However, you can still play/pause

and file skip from the unit.

USB

MUSIC DRIVE DRIVE CHANGE

:The next drive ([

DRIVE 1

] to [

DRIVE 5

]) is selected

automatically and playback starts.

Repeat steps

to select the following drives.

SKIP SEARCH 0.5%

10%

: While listening to iPod, ANDROID or KME

Light/ KMC file, selects the skip search ratio over the total files.

Pandora®

Preparation:

Install the latest version of the Pandora application on your device

(iPhone/ iPod touch), then create an account and log in to Pandora.

• Select [

] for [

PANDORA SRC

]. ( 

)

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

The source changes to PANDORA and broadcast starts.

To On the faceplate On the remote control

Playback / pause

Press

. Press

Skip a track

Press T.

Press

Thumbs up or thumbs

down

Press / .

Press

/ .

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

Create and save a new station

Press and hold the volume knob.

2 Turn the volume knob to select [

FROM TRACK

] or [

FROM ARTIST

], then

press the knob.

A new station is created based on the current song or artist.

3 Press and hold one of the number buttons (1to5) to store.

To select a stored station, press one of the number buttons (1to5).

Search for a registered station

Press .

2 Turn the volume knob to make a selection, then press the knob.

[

BY DATE

]:According to the registered date

[

A-Z

]:Alphabetical order

3 Turn the volume knob to the desired station, then press the knob.

To cancel, press and hold .

(or using RC-406)

Press J / K to search for a station, then press .

Bookmark a song or artist information

Press and hold J.

2 Turn the volume knob to make a selection, then press the knob.

[

THIS TRACK

]:Current song information

[

THIS ARTIST

]:Current artist information

“BOOKMARKED” appears and the information is stored to your device.

The bookmark is available on your Pandora account but not on this

unit.

USB input terminal

KCA-iP102 / KCA-iP103 (optional

accessory)

or accessory cable of

the iPod/iPhone

ENGLISH

iHeartRadio®

Preparation:

Install the latest version of iHeart Link for KENWOOD application on your device

(iPhone/ iPod touch), then create an account and log in to iHeartRadio.

• Select [

] for [

IHEART SRC

]. ( 

)

Start listening

Open the iHeart Link application on your device.

2 Connect your device to the USB input terminal.

3 Press repeatedly to select IHEARTRADIO.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback / pause

Press

. Press

Skip a track for custom station

Press T.

Press

Thumbs up or thumbs down

for custom station

Press

/ .



Create a new/custom station Press 1.

Add to favorite stations for live

station

Press 2.



Scan for live station Press 5.

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

Search for a station

Press .

2 Turn the volume knob to select a category, then press the

knob.

3 Turn the volume knob to the desired station, then press the

knob.

When a city list appears, you can skip cities in alphabetical order

To cancel, press and hold .

(or using RC-406)

Press J / K to search for a station, then press .

Skip cities by alphabetical order

While a city list appears during search...

1 Turn the volume knob quickly to enter character search.

2 Turn the volume knob or press S/T to select the

character to be searched for.

3 Press J / K to move to the previous/next page.

4 Press the volume knob to start searching.

To cancel, press and hold .

Delete a station

While listening to IHEARTRADIO...

1 Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select [

SYSTEM

], then press the knob.

3 Turn the volume knob to select [

STATION DEL

], then press the

knob.

4 Turn the volume knob to select [

LIVE

] or [

CUSTOM

], then press

the knob.

5 Turn the volume knob to select the desired station to delete,

then press the knob.

6 Turn the volume knob to select [

YES

], then press the knob.

7 Press and hold to exit.

To return to the previous setting item, press .

USB input terminal

KCA-iP102 / KCA-iP103 (optional

accessory)

or accessory cable of

the iPod/iPhone

SiriusXM® Radio

Only SiriusXM® brings you more of what you love to listen to, all in one

place. Get over 140 channels, including commercial-free music plus the

best sports, news, talk, comedy and entertainment. Welcome to the world

of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required.

For more information, visit www.siriusxm.com.

Preparation:

1 Connect the optional SiriusXM Vehicle Tuner (commercially

available).

2 Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by

tuning to Channel 0 as well as on the label found on the SiriusXM

Connect tuner and its’ packaging.

The Radio ID does not include the letters I, O, S or F.

3 Activate the subscription.

For users in U.S.A.:

Online: Go to www.siriusxm.com

Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to www.siriusxm.ca/activatexm

Phone: Call 1-877-438-9677

4 Press repeatedly to select SIRIUSXM to start updating.

Start listening

Press repeatedly to select SIRIUSXM.

2 Press repeatedly to select a band.

3 Press .

“

” lights up.

4 Turn the volume knob to select a category, then press the knob.

If “ALL CHANNELS” is selected, all the available channels will be

shown.

5 Turn the volume knob to select a channel, then press the knob.

(or)

Press S / T to search for a channel manually.

• Pressing and holding S / T changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input

screen appears. Enter the pass code to receive the channel. (



)

To change the tuning method for S/T: Press

Each time you press

, the tuning method switches between

“CHANNEL” (manually search for a channel) and “PRESET” (searches for a

preset channel of the selected band).

Direct Access Tuning (using RC-406) (

except for

)

Press DIRECT to enter Direct Access Tuning.

2 Press the number buttons to enter a channel number.

3 Press to start searching.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step

2, Direct Access Tuning

is automatically canceled.

Expansion port on

the rear panel

SiriusXM Vehicle Tuner

Antenna

ENGLISH

SiriusXM® Radio

SiriusXM Keymode

Press and hold to change the keymode (channel or replay).

(Default: Channel keymode)

“

” lights up when replay keymode is selected.

When channel keymode is selected...

To On the faceplate On the remote control

Select a channel

Press S/T. Press S / .

Change a channel

rapidly

Press and hold S/T. Press and hold S /

Store a channel of

the current band

Press and hold one of the

number buttons (1to6).

—

Select a stored

channel of the

current band

Press one of the number buttons (1to6).

When replay keymode is selected...

To On the faceplate On the remote control

Playback / pause

Press

. Press

Select a track

Press S/T. Press S/

Rewind /

Fast-forward

Press and hold S/T. Press and hold S/

Go to Live Press 1.

SmartFavorites and TuneStart™

User stored channels (1 to 6) of the current band are recognized as

SmartFavorite channels. SiriusXM Vehicle Tuner automatically buffers the

broadcast content in the background.

• SmartFavorites feature is available with SXV200 or later SiriusXM tuner

models.

When you select a SmartFavorite channel, you can rewind and replay up

to 30minutes of any of the missed news, talk, sports or music content.

• Playback starts from the beginning of the song if [

TUNE START

] is set to

[

] ( 

) for most music channels stored as a SmartFavorite.

1 Press one of the number buttons (1 to 6) to select a channel.

2 For operation ( 

SiriusXM Keymode

)

TuneScan™

You can get a short preview of the songs that you have missed on each of

your SmartFavorite music channels or current tuned music channel.

Press and hold

to start scanning the first 6 seconds of the

recorded music contents.

• To listen to the current song, press the volume knob to stop scanning.

The unit continues playing the current song.

• To select the previous/next song, press S/T.

• To cancel scanning, press and hold the volume knob. Playback returns

to the channel before you enter TuneScan.

SiriusXM settings

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select [

SIRIUS XM

], then press the knob.

3 Turn the volume knob to make a selection ( 

), then press the

knob.

4 Repeat step 3 until the desired item is selected/activated or follow

the instructions stated on the selected item.

5 Press and hold to exit.

To return to the previous setting item, press .

SiriusXM® Radio

Default:

CHANNEL LOCK

To unlock settings:

Turn the volume knob to select a number.

Press

S / T

to move to the entry position.

Repeat steps

and

to enter the current pass code.

(Initial pass code is 0000.)

Press the volume knob to confirm.

CODE SET

Turn the volume knob to select a number.

Press

S / T

to move to the entry position.

Repeat steps

and

to enter a new 4-digit pass code.

Press the volume knob to confirm.

Repeat steps

to reconfirm the pass code.

•

Make a note of the new pass code to enter channel lock settings

from next time.

LOCK SETTING MATURE CH

:Selects the SiriusXM-defined lock setting.;

USER

DEFINED

:Selects the user-defined lock setting.;

OFF

:Cancels.

CHANNEL EDIT

Turn the volume knob to select a category, then press the knob.

Turn the volume knob to select a channel you want to lock, then

press the knob.

“L” appears in front of the channel number.

Press and hold to exit.

CHANNEL CLEAR

YES

:Clears all the locked channels.;

:Cancels.

TUNE START

:Selected SmartFavorite channel starts playback from the

beginning of the song.;

OFF

:Cancels.

SIGNAL LEVEL NO SIGNAL

WEAK

GOOD

STRONG

:Shows the strength of the

current received signal.

BUFFER USAGE 0%

—

100%

(

):Shows the memory usage for Replay buffer.

SXM RESET YES

:Resets stored channel and lock setting to default.;

:Cancels.

Displayed only when [

USER DEFINED

] is selected.

Available only if the connected SiriusXM Vehical Tuner is SXV200 or later that supports

SmartFavorites.

AUX

Preparation:

Select [

] for [

BUILT-IN AUX

]. ( 

)

Start listening

Connect a portable audio player (commercially available).

2 Press repeatedly to select AUX.

3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select [

SYSTEM

], then press the knob.

3 Turn the volume knob to select [

AUX NAME SET

], then press the knob.

4 Turn the volume knob to make a selection, then press the knob.

AUX

(default)/

DVD

PORTABLE

GAME

VIDEO

5 Press and hold to exit.

To return to the previous setting item, press .

Auxiliary input jack

Portable audio player

3.5mm (1/8") stereo mini plug with “L”

shaped connector (commercially available)

ENGLISH

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP)

– Serial Port Profile (SPP)

– Phonebook Access Profile (PBAP)

– Advanced Audio Distribution Profile (A2DP)

– Audio/Video Remote Control Profile (AVRCP)

Supported Bluetooth codecs

– Sub Band Codec (SBC)

– Advanced Audio Coding (AAC)

– aptX Codec (aptX)

Connect the microphone

Adjust the

microphone angle

Secure using cord clamps (not

supplied) if necessary.

MIC (Microphone input terminal)

Microphone

(supplied)

Rear panel

Pair a Bluetooth device

When connecting a Bluetooth device to the unit for the first time, perform pairing between the

unit and the device.

1 Press to turn on the unit.

2 Search and select this unit model name (KDC-X5

/ KDC-BT5

U/ KMR-D5

BT) on the

Bluetooth device.

“PAIRING”

“PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” scrolls on the

display.

• For some Bluetooth devices, you may need to enter the Personal Identification Number

(PIN) code immediately after searching.

• Refer also to the manual supplied with your Bluetooth device.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed and “

” will light up when the Bluetooth

connection is established.

• Up to five devices can be registered (paired) in total.

• Only one Bluetooth device can be connected at any time.

• This unit supports Secure Simple Pairing (SSP).

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the

device to the unit manually. Refer to the instruction manual of the Bluetooth device for more

information.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if

you reset the unit. To delete the paired device,

, [

DEVICE DELETE

• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing

request (via Bluetooth) is automatically activated. Press the volume knob to pair once you have

confirmed the device name.

Automatic pairing request is activated only if:

– Bluetooth function of the connected devcie is turned on.

– [

AUTO PAIRING

] is set to [

]. (

)

– KENWOOD MUSIC PLAY application is installed on the Android device.

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

– All the buttons and display flash.

– The unit answers the call automatically if [

AUTO ANSWER

] is set to a selected time. ( 

)

During a call:

– The buttons and display illuminate according to the settings made for [

DISPLAY

]. ( 

)

– If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

To On the faceplate On the remote control

Answer a call

Press

or the volume knob or one

of the number buttons (1 to 6).

Press .

Reject a call

Press

End a call

Press

or .

Press

Adjust the phone volume

[00]

[35]

(Default:

[15]*

)

Turn the volume knob during a call.

• This adjustment will not affect the

volume of the other sources.

—

Switch between hands-

free and private talk

modes

Press

during a call.

• Operations may vary according to

the connected Bluetooth device.

—

Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to make a selection

(see the following table), then press the knob.

3 Repeat step 2 until the desired item is

selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

MIC GAIN –10

—

+10

(

–4

):The sensitivity of

the microphone increases as the number

increased.

NR LEVEL –5

—

(

):Adjust the noise reduction

level until the least noise is being heard

during a phone conversation.

ECHO CANCEL –5

—

(

):Adjust the echo cancellation

delay time until the least echo is being heard

during a phone conversation.

BLUETOOTH®

ENGLISH

BLUETOOTH®

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also

possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode.

2 Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on

the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

Press the volume knob to select a name or a phone number.

• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the

previous call status.

• Press

to change the display category (NUMBER or NAME).

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

PHONE BOOK

Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts).

The first menu (ABCDEFGHIJK) appears.

• To go to the other menu (LMNOPQRSTUV or WXYZ1

), press

J / K

• To select the desired first letter, turn the volume knob or press

S / T

, then press the knob.

Select “1” to search with numbers and select “

” to search with symbols.

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob to call.

•

If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the unit

when pairing.

•

Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL

•

This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)

Make the settings for receiving a

call

Press to enter Bluetooth mode.

2 Turn the volume knob to make a

selection (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is

selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press

Default:

SETTINGS

AUTO ANSWER

—

:The unit answers incoming

call automatically in the selected

time (in seconds).;

OFF

:Cancels.

BATT/SIGNAL AUTO

:Shows the strength of the

battery and signal when the unit

detects a Bluetooth device and the

Bluetooth device is connected.;

OFF

:Cancels. Clock time is shown.

BLUETOOTH®

NUMBER DIAL

Turn the volume knob to select a number (0 to

9) or character (

, #, +).

Press

S / T

to move the entry position.

Repeat steps

and

until you finish entering

the phone number.

Press the volume knob to call.

(or using RC-406)

Press the number buttons (

) to enter the

phone number.

Press

to call.

VOICE

Speak the name of the contact you want to call or

the voice command to control the phone functions.

(



Make a call using voice recognition

)

BATT

LOW

MID

FULL

:Shows the strength of the

battery.

SIGNAL

NO SIGNAL

LOW

MID

MAX

:Shows the strength

of the current received signal.

Functionality depends on the type of the phone used.

Make a call using voice recognition

Press and hold to activate the connected

phone.

2 Speak the name of the contact you want to call

or the voice command to control the phone

functions.

• Supported Voice Recognition features vary for

each phone. Refer to the instruction manual of the

connected phone for details.

• This unit also supports the intelligent personal

assistant function of iPhone.

Delete a contact

Press to enter Bluetooth mode.

2 Turn the volume knob to select [

CALL HISTORY

], then press the knob.

3 Turn the volume knob to select a contact.

4 Press and hold the volume knob to enter delete mode.

5 Turn the volume knob to select [

DELETE ONE

] or [

DELETE ALL

], then press the knob.

DELETE ONE

: Selected name or phone number in step 3 is deleted.

DELETE ALL:

All names or phone numbers in [

CALL HISTORY

] in step 2 is deleted.

6 Turn the volume knob to select [

YES

], then press the knob.

7 Press and hold to exit.

• To return to the previous setting item, press .

• Not applicable for mobile phone that supports PBAP.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode.

2 Turn the volume knob to select [

CALL HISTORY

], [

PHONE BOOK

], or [

NUMBER DIAL

], then

press the knob.

3 Turn the volume knob to select a contact or enter a phone number.

If a contact is selected, press the volume knob to show the phone number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored.

To erase a contact from the preset memory, select [

NUMBER DIAL

] in step 2 and store a blank

number.

Make a call from memory

Press to enter Bluetooth mode.

2 Press one of the number buttons (1 to 6).

3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

ENGLISH

BLUETOOTH®

Bluetooth test mode

You can check the connectivity of the supported

profile between the Bluetooth device and the

unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000”

appears.

2 Search and select this unit model name

(KDC-X5

/ KDC-BT5

U/ KMR-D5

BT)

on the Bluetooth device.

3 Operate the Bluetooth device to confirm

pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after

the test.

PAIRING: Pairing status

HF CNT: Hands-Free Profile (HFP) compatibility

AUD CNT: Advanced Audio Distribution Profile

(A2DP) compatibility

PB DL: Phonebook Access profile (PBAP)

compatibility

To cancel test mode, press and hold

turn off the unit.

Other settings

Press the volume knob to enter

[FUNCTION

2 Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated

on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

Selects the phone or audio device to connect or disconnect.

“

” appears in front of the device name when connected.

•

You can only connect another Bluetooth device by disconnecting the connected Bluetooth device

first.

“

” disappears when disconnected.

AUDIO SELECT

DEVICE DELETE

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select [

YES

] or [

], then press the knob.

PIN CODE EDIT

(0000)

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press

/

to move the entry position.

Repeat steps

and

until you finish entering the PIN code.

Press the volume knob to confirm.

RECONNECT ON

:The unit automatically reconnect when the last connected Bluetooth device is within range.;

OFF

:Cancels.

AUTO PAIRING ON

:The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/ Android device)

when it is connected through USB input terminal.Depending on the operating system of the

connected device, this function may not work. ;

OFF

:Cancels.

INITIALIZE YES

:Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.).;

:Cancels.

Internet radio via Bluetooth

Listen to Pandora

Preparation:

Select [

] for [

PANDORA SRC

]. ( 

)

You can listen to Pandora on your smart phone

(Android OS) through Bluetooth on this unit.

1 Open the Pandora application on your device.

2 Connect your Bluetooth audio player via

Bluetooth connection. (



)

3 Press repeatedly to select PANDORA.

The source switches and broadcast starts

automatically.

You can operate Pandora in the same way as Pandora

for iPod/iPhone. (



)

Listen to iHeartRadio

Preparation:

Select [

] for [

IHEART SRC

]. ( 

)

You can listen to iHeartRadio on your smart phone

(Android OS) through Bluetooth on this unit.

1 Open the iHeart Link application on your smart

phone.

2 Connect your smart phone via Bluetooth

connection. (



)

3 Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts

automatically.

You can operate iHeartRadio in the same way as

iHeartRadio for iPod/iPhone. (



)

BLUETOOTH — Audio

Audio player via Bluetooth

Press repeatedly to select BTAUDIO (or press SRC on RC-406).

2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback / pause

Press

. Press

Select group or folder

Press J / K.

Press

/ .

Reverse /

Forward skip

Press S/T. Press S/

Reverse /

Fast-forward

Press and hold S/T. Press and hold S/

Repeat play Press

repeatedly.

ALL REPEAT

FILE REPEAT

REPEAT OFF



Random play Press

repeatedly.

FOLDER RANDOM

RANDOM OFF



Press and hold to select

ALL RANDOM

Operations and display indications may differ according to their availability on the

connected device.

BLUETOOTH®

ENGLISH

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select [

AUDIO CONTROL

], then press the

knob.

3 Turn the volume knob to make a selection (see the following

table), then press the knob.

4 Repeat step 3 until the desired item is selected or activated.

5 Press and hold to exit.

(or using RC-406)

1 Press AUD to enter [

AUDIO CONTROL

2 Press J / K to make a selection, then press .

To return to the previous setting item, press

Default:

SUB-W LEVEL –15

+15

(

) Adjusts the subwoofer output level.

For

BAND1 LEVEL –8

(

)

The sound elements (frequency level, tone level,

Q factor) are preset into each selection (

BAND1

LEVEL

BAND5 LEVEL

Adjusts the level to memorize for each source.

(Before making an adjustment, select the source

you want to adjust.)

BAND2 LEVEL –8

(

)

BAND3 LEVEL –8

(

)

BAND4 LEVEL –8

(

)

BAND5 LEVEL –8

(

)

For

/ :

BASS LEVEL –8

(

)

Adjusts the level to memorize for each source.

(Before making an adjustment, select the source

you want to adjust.)

MID LEVEL –8

(

)

TRE LEVEL –8

(

)

EQ PRO

(for / )

BASS ADJUST BASS CTR FRQ 60HZ

80HZ

100HZ

200HZ

:Selects the center

frequency.

BASS LEVEL –8

(

):Adjusts the level.

BASS Q FACTOR 1.00

1.25

1.50

2.00

:Adjusts the quality factor.

BASS EXTEND ON

:Turns on the extended bass.;

OFF

:Cancels.

MID ADJUST MID CTR FRQ 0.5KHZ

1.0KHZ

1.5KHZ

2.5KHZ

:Selects the center

frequency.

MID LEVEL –8

(

):Adjusts the level.

MID Q FACTOR 0.75

1.00

1.25

:Adjusts the quality factor.

TRE ADJUST TRE CTR FRQ 10.0KHZ

12.5KHZ

15.0KHZ

17.5KHZ

:Selects the

center frequency.

TRE LEVEL –8

(

):Adjusts the level.

PRESET EQ DRIVE EQ

TOP40

POWERFUL

ROCK

POPS

EASY

JAZZ

NATURAL

USER

:Selects a preset equalizer suitable to the music genre. (Select [

USER

]

to use the customized settings.)

[

DRIVE EQ

] is a preset equalizer that reduces noise outside the car or

running noise of the tyres.

BASS BOOST LEVEL1

LEVEL2

LEVEL3

:Selects your preferred bass boost level.;

OFF

:Cancels.

LOUDNESS LEVEL1

LEVEL2

:Selects your preferred low and high frequencies boost to

produce a well-balanced sound at a low volume level.;

OFF

:Cancels.

For

EXTRA EQ LEVEL1

LEVEL2

LEVEL3

:Selects your preferred elevation level to enhance

the sound in [

PRESET EQ

].;

OFF

:Cancels.

SUBWOOFER SET ON

:Turns on the subwoofer output.;

OFF

:Cancels.

DISPLAY SETTINGS

1 Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select [

DISPLAY

], then press the knob.

3 Turn the volume knob to make a selection (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected/activated or follow

the instructions stated on the selected item.

5 Press and hold to exit.

To return to the previous setting item, press .

Default:

COLOR SELECT VARIABLE SCAN

CUSTOM R/G/B

/ preset colors*: Selects your preferred

key and display illumination color.

You can create your own color (when [

CUSTOM R/G/B

] or preset colors* is

selected). The color you have created can be stored in [

CUSTOM R/G/B

Press and hold the volume knob to enter the detailed color adjustment.

Press

/

to select the color (

) to adjust.

Turn the volume knob to adjust the level (

—

), then press the knob.

DIMMER ON

:Dims the display and button illumination.;

OFF

:Cancels.

BRIGHTNESS 0

—

: Selects your preferred brightness level for display and button

illumination.

TEXT SCROLL AUTO

ONCE

:Selects whether to scroll the display information

automatically, or scroll only once.;

OFF

:Cancels.

Preset colors:

RED1

RED2

RED3

PURPLE1

PURPLE2

PURPLE3

PURPLE4

BLUE1

BLUE2

BLUE3

SKYBLUE1

SKYBLUE2

LIGHTBLUE

AQUA1

AQUA2

GREEN1

GREEN2

GREEN3

YELLOWGREEN1

YELLOWGREEN2

YELLOW

ORANGE1

ORANGE2

ORANGERED

AUDIO SETTINGS

LPF SUBWOOFER THROUGH

:All signals are sent to the subwoofer.;

85HZ

120HZ

160HZ

:Audio signals with frequencies lower than 85Hz/ 120Hz/

160Hz are sent to the subwoofer.

SUB-W PHASE REVERSE

(180°)/

NORMAL

(0°): Selects the phase of the subwoofer

output to be in line with the speaker output for optimum

performance. (Selectable only if a setting other than [

THROUGH

] is

selected for [

LPF SUBWOOFER

].)

HPF THROUGH

:All signals are sent to the speakers.;

100HZ

120HZ

150HZ

:Audio signals with frequencies higher than 100Hz/ 120Hz/

150Hz are sent to the speakers.

FADER R15

F15

(

):Adjusts the rear and front speaker output balance.

BALANCE L15

R15

(

):Adjusts the left and right speaker output balance.

VOLUME OFFSET

For AUX:

–8

(

) ; For other sources:

–8

:Presets the

volume adjustment level of each source. (Before adjustment, select

the source you want to adjust.)

SOUND RECNSTR

(Sound reconstruction)

:Creates realistic sound by compensating the high-frequency

components and restoring the rise-time of the waveform that are

lost in audio data compression.;

OFF

:Cancels.

[

SUB-W LEVEL

]/ [

LPF SUBWOOFER

]/ [

SUB-W PHASE

] is selectable only if

[

SUBWOOFER SET

] is set to [

ENGLISH

MORE INFORMATION

General

•

This unit can only play the following CDs:

•

Detailed information and notes about the playable audio files are stated in an online manual

on the following web site: www.kenwood.com/cs/ce/audiofile/

Playable files

•

Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.m4a)

•

Playable disc media: CD-R/CD-RW/CD-ROM

•

Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.

•

Playable USB device file system: FAT12, FAT16, FAT32

Even when audio files comply with the standards listed above, playback may be impossible

depending on the types or conditions of media or device.

Unplayable discs

•

Discs that are not round.

•

Discs with coloring on the recording surface or discs that are dirty.

•

Recordable/ReWritable discs that have not been finalized.

•

8cm CD. Attempting to insert using an adapter may cause malfunction.

About USB devices

•

This unit can play MP3/WMA/AAC/WAV files stored on a USB mass storage class device.

•

You cannot connect a USB device via a USB hub.

•

Connecting a cable whose total length is longer than 5m may result in abnormal playback.

•

This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.

About KENWOOD Music Editor Light and KENWOOD Music Control

•

This unit supports the PC application KENWOOD Music Editor Light and Android™ application

KENWOOD Music Control.

•

When you play audio files with song data added using the KENWOOD Music Editor Light or

KENWOOD Music Control, you can search for audio files by Genres, Artists, Albums, Playlists,

and Songs.

•

KENWOOD Music Editor Light and KENWOOD Music Control are available on the following

web site: www.kenwood.com/cs/ce/

About iPod/iPhone

Made for

iPod touch (2nd, 3rd, 4th, and 5th generation)

iPod classic

iPod nano (3rd, 4th, 5th, 6th, and 7th generation)

iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C

•

For the latest compatible list and software versions of iPhone/iPod, see:

www.kenwood.com/cs/ce/ipod

•

You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.

About Android device

•

This unit supports Android OS 4.1 and above.

•

Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory

(AOA) 2.0.

•

If the Android device supports both mass storage class device and AOA 2.0, this unit always

playback via AOA 2.0 as priority.

•

For more information and the latest compatible list, see: www.kenwood.com/cs/ce/

About Pandora

•

Pandora is available only in the U.S., Australia and New Zealand.

•

Because Pandora is a third-party service, the specifications are subject to change without

prior notice. Accordingly, compatibility may be impaired, or some or all of the services may

become unavailable.

•

Some functions of Pandora cannot be operated from this unit.

•

For issues using the application, please contact Pandora at pandora-support@pandora.com.

About iHeartRadio

•

iHeartRadio® is a third-party service, therefore the specifications are subject to change

without prior notice. Accordingly, compatibility may be impaired or some or all of the

services may become unavailable.

•

Some iHeartRadio® functionality cannot be operated from this unit.

About Bluetooth

•

Depending on the Bluetooth version of the device, some Bluetooth devices may not be able

to connect to this unit.

•

This unit may not work with some Bluetooth devices.

•

Signal conditions vary, depending on the surroundings.

•

For more information about Bluetooth, visit the following website:

www.kenwood.com/cs/ce/

Symptom Remedy

CD / USB / iPod

“NO DISC” Insert a playable disc into the loading slot.

“TOC ERROR” Make sure the disc is clean and inserted properly.

“PLEASE EJECT” Reset the unit. If this does not solve the problem, consult

your nearest service center.

“READ ERROR” Copy the files and folders onto the USB device again. If this

does not solve the problem, reset the USB device or use

another USB device.

“NO DEVICE” Connect a USB device, and change the source to USB again.

“COPY PRO” A copy-protected file is played.

“NA DEVICE” Connect a supported USB device, and check the

connections.

“NO MUSIC” Connect a USB device that contains playable audio files.

“iPod ERROR”

•

Reconnect the iPod.

•

Reset the iPod.

ANDROID

•

Sound cannot be heard

during playback.

•

Sound output only

from the Android

device.

•

Reconnect the Android device.

•

If in [

HAND MODE

], launch any media player

application on the Android device and start playback.

•

If in [

HAND MODE

], relaunch the current media player

application or use another media player application.

•

Restart the Android device.

•

If this does not solve the problem, the connected

Android device is unable to route the audio signal to

unit. (



)

Cannot playback at

[

BROWSE MODE

•

Make sure KENWOOD MUSIC PLAY APP is installed on

the Android device. (



)

•

Reconnect the Android device and make the appropriate

setting in [

ANDROID SETUP

]. ( 

)

•

If this does not solve the problem, the connected

Android device does not support [

BROWSE MODE

(



)

TROUBLESHOOTING

Symptom Remedy

General

Sound cannot be heard.

•

Adjust the volume to the optimum level.

•

Check the cords and connections.

“MISWIRING CHECK WIRING

THEN PWR ON” appears.

Turn the power off, then check to be sure the

terminals of the speaker wires are insulated

properly. Turn the power on again.

“PROTECTING SEND SERVICE”

appears.

Send the unit to the nearest service center.

•

Sound cannot be heard.

•

The unit does not turn on.

•

Information shown on the

display is incorrect.

Clean the connectors. (



)

The unit does not work at all. Reset the unit. (



)

Radio

•

Radio reception is poor.

•

Static noise while listening to

the radio.

•

Connect the antenna firmly.

•

Pull the antenna out all the way.

CD / USB / iPod

Disc cannot be ejected.

Press and hold

to forcibly eject the disc. Be

careful not to drop the disc when it is ejected. If this

does not solve the problem, reset the unit. (



)

Noise is generated. Skip to another track or change the disc.

Tracks do not play back as you

intended them to play.

Playback order is determined when files are

recorded.

“READING” keeps flashing. Do not use too many hierarchical levels or folders.

Elapsed playing time is not

correct.

This is caused by how the tracks are recorded.

Correct characters are not displayed

(e.g. album name).

This unit can only display uppercase letters,

numbers, and a limited number of symbols.

“NA FILE” Make sure the disc contains supported audio files.

(



)

ENGLISH

Symptom Remedy

iHeartRadio

“NOSTATIONS” No stations are found.

“NOT CONNECTED” Link to the application is impossible.

“IHEARTLINK UP” Make sure you have installed the latest version of the iHeart

Link for KENWOOD application on your device.

“PLEASE LOGIN” You haven’t log in. Log in again.

“STATION NOT

AVAILABLE”

Broadcast from the station is over.

“STATION NOT

SELECTED”

No station is selected.

“STREAM ERROR” Broadcast data is interrupted.

“THUMB FAILED” Registration of Thumbs Up/Down has failed.

“TIMED OUT” The request has resulted in time-out.

SiriusXM® Radio

“CHLOCKED LOCK

CODE?”

The selected channel is locked. Enter the correct pass code to

unlock. (



)

“CHANUNSUB” The selected channel is unsubscribed. Call 1-866-635-2349 in

U.S.A. or 1-877-438-9677 in Canada to subscribe. (



)

“CHUNAVAIL” The selected channel is unavailable. Visit www.siriusxm.com

for more information about the SiriusXM channel lineup.

“CHECKANTENNA”

Check the antenna and its connection are in good condition.

“CHECKTUNER”

Make sure the SiriusXM Vehicle Tuner is connected to the unit.

“NOSIGNAL” Make sure the antenna is mounted outside the vehicle.

“

SUBSCRIPTION

UPDATED – PRESS

ENTER TO CONTINUE.

”

Your subscription is updated. Press the volume knob to

continue.

“CODE ERROR” Make sure you have entered the correct pass code. (



)

“NO CONTENT”

There is insufficient content to start TuneScan.

“SCAN CANCEL”

TuneScan has been aborted.

TROUBLESHOOTING

Symptom Remedy

ANDROID

“NO DEVICE” or

“READING” keeps

flashing.

•

Switch off the developer options on the Android device.

•

Reconnect the Android device.

•

If this does not solve the problem, the connected

Android device does not support [

BROWSE MODE

(



)

Playback is intermittent

or sound skips.

Turn off the power saving mode on the Android device.

“ANDROID ERROR” /

“NADEVICE”

•

Reconnect the Android device.

•

Restart the Android device.

Pandora

“ADDERROR” /

“SEARCHERROR”

New station creation is unsuccessful.

“CHECKDEVICE” Check the Pandora application on your device.

“NOSKIPS” The skip limit has been reached.

“NOSTATIONS” No stations are found.

“STATIONLIMIT” The number of registered stations has reached its limit.

Retry after deleting unnecessary stations from your device.

“CONNECT ERROR” Communication is unstable.

“RATING ERROR” Registration of thumbs up/thumbs down has failed.

“LICENSE ERROR” You try to access from a country which Pandora is not

deliverable.

iHeartRadio

iHeartRadio station

cannot be selected.

If “Explicit Content” in [Account Settings] is checked in

the web version of iHeartRADIO, custom stations become

unavailable.

“CANNOT CREATE” Custom station name creation is unsuccessful.

“CANNOT SAVE” Addition to the favorite category failed.

“DISCONNECTED” Check the connection to the device.

“NOSKIPS” The skip limit has been reached. Retry later.

+ 57 hidden pages