Data sheet
Actuators for three point control AMV 01, AMV 02, AMV-H 01, AMV-H 02
Description
AMV 01, AMV 02
AMV-H 01, AMV-H 02
AMV 01/02 and AMV-H 01/02 actuators are used withVZ,VZL,VRBZ or with AB-QM valves (AMV version only).The actuator can be used with fan coil units, induction units, small reheaters, recoolers, and zone applications in which hot/ cold water is the controlled medium.
Main data:
•3-point versions
•The advanced design incorporates no-force switch-o at stem up position, which enables use of the actuator on valves with di erent nominal strokes and improves the controller response
•Force switch-o at stem down position prevents overload of actuator and valve
•No tools required for mounting
•Maintenance free during the lifetime
•Low noise operation
•Supplied with 1.5 m cable.
Ordering |
|
|
|
|
|
Spare parts |
|
Type |
Supply |
Speed |
Code No. |
|
|||
|
|
|
|
||||
|
voltage |
|
Type |
Code No. |
|||
|
|
|
|
|
|||
|
|
|
|
|
|
||
|
AMV 01 |
|
24 s/mm |
082H8001 |
|
|
|
|
|
|
1.5 m cable for AMV, AMV-H - 24 V |
082H8007 |
|||
|
|
|
|
|
|
||
|
AMV 02 |
|
12 s/mm |
082H8004 |
|
|
|
|
24 V~ |
|
1.5 m cable for AMV, AMV-H - 230 V |
082H8008 |
|||
|
|
|
|
|
|||
|
AMV-H 01 |
24 s/mm |
082H8021 |
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
AMV-H 02 |
|
12 s/mm |
082H8024 |
|
|
|
|
|
|
|
|
|
|
|
|
AMV 01 |
|
24 s/mm |
082H8002 |
|
|
|
|
|
|
|
|
|
|
|
|
AMV 02 |
230 V~ |
12 s/mm |
082H8005 |
|
|
|
|
|
|
|
|
|
|
|
|
AMV-H 01 |
24 s/mm |
082H8022 |
|
|
|
|
|
|
|
|
|
|
|
|
|
AMV-H 02 |
|
12 s/mm |
082H8025 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Technical data |
Type |
AMV 01, AMV-H 01 |
AMV 02, AMV-H 02 |
|
|||
|
Power supply |
24 Vac, 230 Vac; +10 to –15% |
|
|
Power consumption |
1 VA - 24 Vac; 7 VA-230 Vac |
|
|
Frequency |
50 Hz/60 Hz |
|
|
Close of force |
200 N |
|
|
Max. stroke |
5.5 mm |
|
|
Speed |
24 s/mm |
12 s/mm |
|
Max. medium temperature inside the pipe |
120 °C |
|
|
Ambient temperature |
0 to 55 °C |
|
|
Storage and transport temperature |
–40 to +70 °C |
|
|
Protection code |
IP 42 |
|
|
Weight |
0.34 kg |
|
|
- marking in accordance with standards |
EMCDirective 89/336/EEC, 92/31/EEC, 93/68/EEC, |
|
|
EN 50081-1 and EN 50082-1 |
|
|
|
|
|
|
|
|
Low voltage Directive 73/23/EEC and 93/68/EEC, |
|
|
|
EN 60730/2/14 |
|
SIBC
VD.JC.M2.02 © Danfoss 08/05 |
1 |
Data sheet |
Actuators for three point control AMV 01, AMV 02, AMV-H 01, AMV-H 02 |
Installation |
Mechanical |
|
The actuator should be mounted with the valve |
|
stem in either horizontal position or pointing |
|
upwards. |
|
The actuator is fixed to the valve body by means |
|
of a mounting ring which requires no tools for |
|
mounting.The ring should be tightened by hand. |
|
Electrical |
|
Important: It is strongly recommended that the |
|
mechanical installation is completed before the |
|
electrical installation. |
|
Each actuator is supplied with the connecting |
|
cable for the controller. |
Wiring
AMV/AMV-H 01, AMV/AMV-H 02 - 24V
|
AMV/AMV-H 01, AMV/AMV-H 02 - 230V |
|
|
|
|
Disposal |
The actuator must be dismantled and the |
|
elements sorted into various material groups |
|
before disposal. |
|
|
Commissioning |
All actuators are factory tested prior to shipment. |
|
The factory setting of the spindle is the fully |
|
stem up position because of easier mechanical |
|
connection of actuator on valve. |
|
Important: Uninstalled actuator will operated |
|
properly only in stem down direction! |
|
If uninstalled actuator is tested than use Allen key |
|
size 4 mm (or knob for AMV-H version) in order to |
|
drive actuator on it's top position. |
2 |
VD.JC.M2.02 © Danfoss 08/05 |
SIBC
Loading...