MVS-7000X
Table of contents
Loading...Sony MVS-7000X, MVS-8000X-C, MKS-7210X, MKS-7470X, MKS-7471X Operation Manual
...
SWITCHER PROCESSOR PACK
MVS-8000X-C
MVS-7000X-C
MULTI FORMAT SWITCHER PROCESSOR
MVS-8000X
MVS-7000X
MKS-7171X MKS-7210X MKS-7470X MKS-7471X
MKS-8110X MKS-8160X MKS-8170X MKS-8180X
MKS-8210X MKS-8440X MKS-8450X BZS-7200X
BZS-7420X BZS-7500X BZS-7510X BZS-7520X
BZS-7530X BZS-7540X BZS-7541X BZS-7560X
BZS-7561X BZS-8200X BZS-8420X BZS-8560X
HK-PSU05
OPERATION MANUAL [English]
1st Edition (Revised 2)
4189511030
WARNING
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
THIS APPARATUS MUST BE EARTHED.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Length Minimum 1.5m (4 ft. 11in.),
Less than 2.5 m (8 ft. 3 in.)
Rating Minimum 10A, 125V
Using this unit at a voltage other than 120V may require the
use of a different line cord or attachment plug, or both. To
reduce the risk of fire or electric shock, refer servicing to
qualified service personnel.
WARNING: THIS WARNING IS APPLICABLE FOR OTHER
COUNTRIES.
1. Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
2. Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Voltage,
Ampere).
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please consult a qualified service
personnel.
For the customers in Europe
This product with the CE marking complies with the EMC
Directive issued by the Commission of the European
Community.
Compliance with this directive implies conformity to the
following European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).
The manufacturer of this product is Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is
Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany.
This apparatus shall not be used in the residential area.
For the customers in Canada
This Class A digital apparatus complies with Canadian ICES-
003.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: THIS WARNING IS APPLICABLE FOR USA
ONLY.
If used in USA, use the UL LISTED power cord specified
below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration)
Cord Type SJT, three 16 or 18 AWG wires
2
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
FORSIKTIG
For å redusere risikoen for støt, plugg inn
strømtilførselsledningene i hver sin kurs, med separat jording.
For the customers in Taiwan only
AVERTISSEMENT
Ne pas utiliser cet appareil dans une zone résidentielle.
Pour les clients en Europe, Australie et Nouvelle-Zélande
AVERTISSEMENT
Il s’agit d’un produit de Classe A. Dans un environnement
domestique, cet appareil peut provoquer des interférences
radio, dans ce cas l’utilisateur peut être amené à prendre des
mesures appropriées.
Afin de réduire les risques d’incendie ou
d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution,
garder le coffret fermé. Ne confier
l’entretien de l’appareil qu’à un personnel
qualifié.
CET APPAREIL DOIT ÊTRE RELIÉ À LA
TERRE.
Pour les clients au Canada
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
AVERTISSEMENT
1.Utilisez un cordon d’alimentation (câble secteur à 3 fils)/
fiche femelle/fiche mâle avec des contacts de mise à la terre
conformes à la réglementation de sécurité locale applicable.
2.Utilisez un cordon d’alimentation (câble secteur à 3 fils)/
fiche femelle/fiche mâle avec des caractéristiques
nominales (tension, ampérage) appropriées.
Pour toute question sur l’utilisation du cordon d’alimentation/
fiche femelle/fiche mâle ci-dessus, consultez un technicien du
service après-vente qualifié.
WARNUNG
Um die Gefahr von Bränden oder
elektrischen Schlägen zu verringern, darf
dieses Gerät nicht Regen oder Feuchtigkeit
ausgesetzt werden.
Um einen elektrischen Schlag zu
vermeiden, darf das Gehäuse nicht
geöffnet werden. Überlassen Sie
Wartungsarbeiten stets nur qualifiziertem
Fachpersonal.
DIESES GERÄT MUSS GEERDET
WERDEN.
WARNUNG
1. Verwenden Sie ein geprüftes Netzkabel (3-adriges
Stromkabel)/einen geprüften Geräteanschluss/einen
geprüften Stecker mit Schutzkontakten entsprechend den
Sicherheitsvorschriften, die im betreffenden Land gelten.
2. Verwenden Sie ein Netzkabel (3-adriges Stromkabel)/einen
Geräteanschluss/einen Stecker mit den geeigneten
Anschlusswerten (Volt, Ampere).
Wenn Sie Fragen zur Verwendung von Netzkabel/
Geräteanschluss/Stecker haben, wenden Sie sich bitte an
qualifiziertes Kundendienstpersonal.
Pour les clients en Europe
Ce produit portant la marque CE est conforme à la Directive
sur la compatibilité électromagnétique (EMC) émise par la
Commission de la Communauté européenne.
La conformité à cette directive implique la conformité aux
normes européennes suivantes:
• EN55103-1 : Interférences électromagnétiques (émission)
• EN55103-2 : Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans l’environnement
électromagnétique suivant: E4 (environnement EMC contrôlé,
ex. studio de télévision).
Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan,
Minato-ku, Tokyo, Japon.
Le représentant autorisé pour EMC et la sécurité des produits
est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Allemagne.
Für Kunden in Europa
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die
EMV-Richtlinie der EG-Kommission.
Angewandte Normen:
• EN55103-1: Elektromagnetische Verträglichkeit
(Störaussendung)
• EN55103-2: Elektromagnetische Verträglichkeit
(Störfestigkeit)
Für die folgende elektromagnetische Umgebung: E4
(kontrollierter EMV-Bereich, z.B. Fernsehstudio).
Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
Der autorisierte Repräsentant für EMV und Produktsicherheit
ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Deutschland.
Dieser Apparat darf nicht im Wohnbereich verwendet werden.
3
Für Kunden in Europa, Australien und Neuseeland
WARNUNG
Dies ist eine Einrichtung, welche die Funk-Entstörung nach
Klasse A besitzt. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen; in diesem Fall kann vom
Betreiber verlangt werden, angemessene Maßnahmen
durchzuführen und dafür aufzukommen.
4
Table of Contents
Overview ............................................................................... 6
Features ..................................................................................... 6
Overview of the MVS-8000X/MVS-7000X Series Components
......................................................................................... 7
Location and Function of Parts ........................................ 11
Front Panel .............................................................................. 11
Rear Panel................................................................................ 11
Example System Configuration ........................................ 16
MVS-8000X/MVS-7000X System Configuration..................16
Flow of Video Signals.............................................................17
Power Supply Unit Status Indicators ............................... 18
Specifications..................................................................... 18
MVS-8000X Multi Format Switcher Processor...................... 18
MVS-7000X Multi Format Switcher Processor...................... 19
MKS-7171X DME Output Connector Board.......................... 20
MKS-7210X Mix Effect Board............................................... 20
MKS-7470X DME Board Set ................................................. 21
MKS-7471X Additional DME Board ..................................... 21
MKS-8110X 20-Input Board................................................... 21
MKS-8160X 24-Output Board Set.......................................... 21
MKS-8170X DME Interface Board Set .................................. 21
MKS-8180X Cross Point Board Set........................................ 22
MKS-8210X Mix Effect Board............................................... 22
MKS-8440X Frame Memory Board Set ................................. 22
MKS-8450X Format Converter Board.................................... 22
HK-PSU05 Power Supply Unit............................................... 23
Table of Contents
5
Overview
The MVS-8000X-C/MVS-7000X-C Switcher Processor
Pack is a high-performance, multi-function, multi-format
switcher processor for use in an MVS-8000X/MVS7000X Multi Format Switcher system. It has a wide range
of application, being usable in live production systems in
studios and ENG/OB vans as well as in postproduction
editing systems.
Features
• As a standard feature, one resizer channel is provided for
each keyer
• Each MKS-8210X/MKS-7210X board is provided with
four (or eight) resizer channels (the maximum number of
MKS-8210X/MKS-7210X boards that can be installed:
five for MVS-8000X system; three for MVS-7000X
system)
However, when using 1080P/59.94 or 1080P/50 format,
there is a maximum of four channels per MKS-8210X/
MKS-7210X boards.
Note
It is not possible to install the MKS-8210X in the MVS7000 system.
Multi format support
MVS-8000X system
The MVS-8000X system is available in two
configurations: the SD/HD multi-format configuration and
a configuration supporting 1080P/59.94 and 1080P/50
formats. The SD/HD multi-format configuration can be
upgraded to the 1080P/59.94 and 1080P/50 configuration.
• SD/HD multi-format configuration:
1080i/59.94, 1080i/50, 1080PsF/29.97, 1080PsF/25,
1080PsF/23.976, 1080PsF/24, 720P/59.94, 720P/50,
480i/59.94, 576i/50
• 1080P/59.94, 1080P/50 configuration:
Supports the following formats in addition to those
supported by the SD/HD multi-format configuration
1080i/59.94 (SMPTE-425M, level B), 1080P/50
(SMPTE-425M, level B)
MVS-7000X system
The MVS-7000X system is available in three
configurations: an SD format configuration, an SD/HD
multi-format configuration, and a configuration
supporting only 1080P/59.94 and 1080P/50 formats. The
SD format configuration can be upgraded to the SD/HD
multi-format configuration and even to the 1080P/59.94
and 1080P/50 configuration.
• SD format configuration:
480i/59.94, 576i/50
• SD/HD multi-format configuration:
1080i/59.94, 1080i/50, 1080PsF/29.97, 1080PsF/25,
1080PsF/23.976, 1080PsF/24, 720P/59.94, 720P/50,
480i/59.94, 576i/50
• 1080P/59.94, 1080P/50 configuration:
Supports the following formats in addition to those
supported by the SD/HD multi-format configuration
1080P/59.94 (SMPTE-425M, level B), 1080P/50
(SMPTE-425M, level B)
Key resizer functions
• Magnify, shrink, and move, plus, rotate either in the Xor Y-axisdirection and change aspect ratio
Format converter function
The inputs and outputs support up converter, down
converter, cross converter, IP converter, and PI converter.
(Future support for IP converter and PI converter)
The MVS-8000X system supports a maximum of 16 input
channels (with two MKS-8450X boards), and the MVS7000X system supports a maximum of eight input
channels (with one MKS-8450X board). However, when
using the IP converter and PI converter, one MKS-8450X
provides a maximum of four channels.
The MVS-8000X/MVS-7000X system supports a
maximum of four output channels (with MKS-8160X
option installed; at least one MKS-8450X board required).
However, when using the IP converter and PI converter,
one MKS-8160X provides only one channel.
Note
These inputs and outputs are not available for 1080P/59.94
or 1080P/50 format. (The IP converter and PI converter
will be supported in future.)
Highly expandable system configuration
By combining option boards, you can configure the
optimum system for your requirements, selecting the
number of inputs and outputs, and the number of M/E
banks. The system’s flexibility guarantees its ability to
meet future expansion requirements.
High-performance keyers
Each M/E bank is equipped with eight high-performance
keyers that provide the following standard functions.
However, for 1080P/59.94 or 1080P/50 format, only four
keyers can be used.
• Ability to apply transitions to keyers independently of
the background
• Chroma key and color vector keys in each keyer
• FineKey™, and key borders up to 8H
• Color mixable matte generator available for both key fill
and key borders
6
Overview
Simultaneous output of two programs
Each M/E bank is able to handle two simultaneous
program outputs, with the ability to apply any of the four
keys to program output. However, when using 1080P/
59.94 or 1080P/50 format, you can select any of the four
keys to apply. This gives the system the ability to handle a
wide range of operating situations, for example
simultaneous transmission of two programs.
Powerful preview functions
The system supports simultaneous output of look-ahead
previews (next preview) and key previews, and also
transition previews.
7000X) can be used in 1080P/59.94 or 1080P/50 format
(for MVS-8000X, future support for channels 3 and 4 other
than in 1080P/59.94 or 1080P/50 format).
Multi Program 2 Mode
By installing the Multi Program 2 Software option (BZS8200X for MVS-8000X system and BZS-7200X for MVS7000X), you can create two different backgrounds, with
transition effects, in each M/E bank. M/E keyers can be
assigned to these backgrounds for separate keying.
This allows you to create multiple programs within a
single M/E bank by varying the keyer assignments and
background video configuration.
Extended frame memory function
• Two-input 16-output frame memory (Future support for
9 to 16 outputs)
However, for 1080P/59.94 or 1080P/50 format, a
maximum of eight outputs can be used (Future support
for 1080P/59.94 and 1080P/50).
• Freeze function, mask function, reposition function, and
image processing function format (Future support for
reposition and image processing functions)
• Provides approximately 10G Bytes of memory (Future
support for 5G Bytes of the 10G Bytes)
• Animation function provided
• Equipped with external hard disk drive connector
Links to DME functions
With an MVE-8000A or MVE-9000 DME Processor
Pack, you can apply DME wipes and processed keys and a
wide variety of other DME functions as if they were native
switcher functions. All DME functions can be controlled
from the center control panel of the MVS-8000X/MVS7000X system.
For 1080P/59.94 and 1080P/50 formats, only an MVE8000A can be used.
Backup power supply can be installed
By installing the optional HK-PSU05 Power Supply Unit,
together with the power supply unit preinstalled at the
factory, this provides a backup system. This reduces the
risk of power supply problems, and increases the reliability
of live operations.
Plug-in DME functionality
In the case of the MVS-7000X system, DME functionality
can be built into the system by installing the MKS-7470X/
MKS-7471X in the switcher processor.
A maximum of four DME channels can be supported in all
formats.
Overview of the MVS-8000X/MVS7000X Series Components
MVS-8000X Multi Format Switcher
Processor
This is the main unit cabinet of the MVS-8000X Multi
Format Switcher Processor unit (EIA 10RU size).
By default only SD/HD multi-format is supported, but by
installing software, 1080P/59.94 and 1080P/50 formats are
also supported.
• Two M/E banks installed as standard; can be extended to
five M/E banks.
• 24 inputs installed as standard; can be extended to 144
inputs.
• 24 outputs installed as standard; can be extended to 48
outputs.
• Depending on the M/E configuration, a maximum of 20
M/E outputs (4M/E+P/P) are available as standard.
• The MKS-8170X DME Interface Board Set (option) can
be installed.
• The BZS-8420X Color Corrector Software (option) can
be used.
• Three power supply units fitted as standard.
High-performance color correction
Installation of the optional Color Corrector Software
(BZS-8420X for MVS-8000X and BZS-7420X for MVS7000X) provides a maximum of four channels (MVS8000X) or two channels (MVS-7000X) of highperformance color correction functionality.
Note that only two color correction channels (MVS8000X) or only one color correction channel (MVS-
MVS-7000X Multi Format Switcher
Processor
This is the main unit cabinet of the MVS-7000X Multi
Format Switcher Processor unit (EIA 8RU size). By
default only SD format is supported, but by installing
software, HD multi-format, 1080P/59.94 and 1080P/50
formats are also supported.
Overview
7
• The standard configuration include no M/E. In 1080P/
59.94 or 1080P/50 format, it can be extended to include
up to three M/Es. In HD multi-format and SD format, the
configuration can be extended to include up to six M/Es.
(Future support for 6th M/E)
• 20 inputs installed as standard. The input configuration
can be extended to 80 inputs.
• 20 outputs installed as standard. The output
configuration can be extended to 48 outputs.
• Plug-in DME options MKS-7470X and MKS-7471X
can be installed.
• A DME interface can be configured by installing the
MKS-8110X 20-Input Board and MKS-7171X Output
Connector Board.
• The BZS-7420X Color Corrector Software (option) can
be used.
• Two power supply units fitted as standard.
The following options can be installed, depending on the
system.
MVS-8000X system
Board Name Maximum
installable number
of boards
MKS-8110X 20-Input Board 6
MKS-8160X 24-Output Board Set 1
MKS-8170X DME Interface Board Set 1
MKS-8180X Cross Point Board Set 1
MKS-8210X Mix Effect Board 3
MKS-8440X Frame Memory Board
Set
MKS-8450X Format Converter Board 2
HK-PSU05 Power Supply Unit 2
1
MVS-7000X system
MKS-7171X DME Output Connector Board
This can be installed only in the MVS-7000X system.
This is an interface board for output of video signals to the
MVE-8000A and MVE-9000 Multi Format DME
Processors. This board can also be used for output of plugin DME V/K (video/key) signals and MON (monitor
video) signals.
MKS-7210X Mix Effect Board
This is an M/E board to be used for the MVS-8000X/
MVS-7000X system.
The MVS-8000X has two M/E banks installed as standard,
which can be extended to five M/E banks by installing this
option.
The MVS-7000X system has no M/E bank as standard.
When using the MVS-7000X system in 1080P/59.94 or
1080P/50 format, a maximum of three M/E banks can be
configured by installing this option. When using the
system in a format other than 1080P/59.94 and 1080P/50,
a maximum of six M/E banks can be configured by
installing three of these boards (Future support for 6th M/
E).
MKS-7470X DME Board Set
This can be installed only in the MVS-7000X system.
The set comprises a DME board and a XPT board. The
MKS-7470X supports two-channel DME functionality for
all formats.
MKS-7471X Additional DME Board
This can be installed only in the MVS-7000X system.
This is a DME board. The MKS-7471X provides two
additional channels for DME functionality. (The
combination of MKS-7470X and MKS-7471X supports 4
channels for all formats.)
Board Name Maximum
installable number
of boards
MKS-7171X DME Output Connector
Board
MKS-7210X Mix Effect Board 3
MKS-7470X DME Board Set 1
MKS-7471X Additional DME Board 1
MKS-8110X 20-Input Board Primary: 3 4
MKS-8160X 24-Output Board Set 1
MKS-8440X Frame Memory Board
Set
MKS-8450X Format Converter
Board
HK-PSU05 Power Supply Unit 2
8
Overview
1
DME interface: 1
1
1
MKS-8110X 20-Input Board
This is a 20-input board.
The MVS-8000X has 24 inputs fitted as standard, and by
installing 20 inputs at a time with this board, a maximum
of 144 inputs (with six boards added) can be reached.
The MVS-7000X has 20 inputs fitted as standard, and by
installing 20 inputs at a time with this board, a maximum
of 80 inputs (with three boards added) can be reached.
When this board is installed in the DME interface slot of
the MVS-7000X system, it can be used as inputs for video
signals from the MVE-8000A and MVE-9000 Multi
Format DME Processors, inputs for V/K (video/key)
signals from the plug-in DME, and inputs for EXTV
(external video) signals.
MKS-8160X 24-Output Board Set
This is a 24-output board set, of which one can be installed.
Loading...