4-180-210-12(1)
Operating Instructions Stereo Manual de instrucciones
Headset
DR-E10iP
©2010 Sony Corporation Printed in Thailand
English
Stereo headset
WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To reduce the risk of electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Compatible iPod/ iPhone models
You can use the unit with only the following models supporting remote control. Update your iPod, iPhone or iPad to the latest software before use. In the Operating Instructions, iPod, iPhone and iPad are collectively described as “iPod” except in special cases.
iPod touch 4th generation
iPod touch 3rd generation
iPod touch 2nd generation
iPod nano 6th generation
iPod nano 5th generation
iPod nano 4th generation
iPod classic 120GB 160GB (2009)
iPod shuffle 4th generation
iPod shuffle 3rd generation
iPhone 4
iPhone 3GS
iPad
On copyright
iPhone®, iPod®, iPod classic®, iPod nano®, iPod shuffle®, and iPod touch® are trademarks of Apple Inc., registered in the U.S. and other countries. iPad® is a trademark of Apple Inc.
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Features
Easy-to-use remote control (only for iPod, iPhone and iPad).
In-line microphone for hands-free phone calls of iPhone.
Earbud style headset in fashionable colors.
Neodymium magnet delivers powerful sound.
How to use
Wearing the headphones (see fig. )
Wear the earpiece marked in your right ear and the one marked in your left ear.
If the headphones do not fit your ears, put on the supplied earpads.
(See fig. )
How to use the cord slider (see fig. - )
Move up and down to change the split position of the cord.
How to use the remote and microphone for an iPod (see fig. - )
You can control a connected iPod product.
Parts and controls
Volume +
Increases the volume of the connected iPod product.
Center button
Plays/pauses a track of the connected iPod product with a single press. Skips to the next track with a double press.
Skips to the previous track with a triple press. Starts the “VoiceOver*” feature with a long press (if available).
Press once to answer the call. Press
again to end.
Hold down for about two seconds to reject an incoming call.
When you let go, two low beeps confirm the call was rejected.Volume –
Decreases the volume of the connected iPod product.
Microphone
*Availability of the “VoiceOver” feature depends on iPod and its software version.
Specifications
Receiver
Type: Open air, dynamic
Driver unit:
13.5 mm, dome type (CCAW)
Power handling capacity:
100 mW (IEC*)
Impedance:
16 Ω at 1 kHz
Sensitivity:
104 dB/mW
Frequency response:
18 – 22,000 Hz
Cord: 1.2 m (47 1/4 in), Litz cord Y-type
Plug: Four-conductor gold-plated stereo mini plug for iPod with remote function
Mass: Approx. 6 g (0.21 oz) without cord
Microphone
Open circuit voltage level:
– 42 dB ( 0 dB=1 V/Pa)
Supplied accessories
Earpads (2)
Card warranty (1) Operating Instructions (1)
*IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Precautions
Listening with headphones at high volume may affect your hearing. For traffic safety, do not use while driving or cycling.
Be careful not to allow any buttons to be unintentionally pressed when the headphones with iPod connected are in a carrying pouch, etc.
Note on static electricity
In particularly dry air conditions, mild tingling may be felt on your ears. This is a result of static electricity accumulated in the body, and not a malfunction of the headphones.
The effect can be minimized by wearing clothes made from natural materials.
Loading...