Sharp AQUOS LC-37HV4U Manual

LC-37HV4U

ENGLISH

FRANÇAIS

LIQUID CRYSTAL TELEVISION TÉLÉVISEUR ACL

TELEVISOR CON PANTALLA DE CRISTAL LIQUIDO

TELEVISOR DE CRISTAL LÍQUIDO

OPERATION MANUAL

MODE D’EMPLOI

MANUAL DE OPERACIÓN

MANUAL DE OPERAÇÃO

PORTUGUÊS ESPAÑOL

LC-37HV4U

LIQUID CRYSTAL TELEVISION

ENGLISH

OPERATION MANUAL

ENGLISH

IMPORTANT:

To aid reporting in case of loss or theft, please record the TV’s model and serial numbers in the space provided. The numbers are located at the rear of the TV.

Model No.:

Serial No.:

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

		The lightning flash with arrow-head
	CAUTION	symbol, within an equilateral
		triangle, is intended to alert the user
	RISK OF ELECTRIC SHOCK	to the presence of uninsulated
	DO NOT OPEN	“dangerous voltage” within the
		product’s enclosure that may be of
		sufficient magnitude to constitute a
		risk of electric shock to persons.
	CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,	The exclamation point within a
	DO NOT REMOVE COVER (OR BACK).	triangle is intended to alert the user
	NO USER-SERVICEABLE PARTS INSIDE.	to the presence of important
	REFER SERVICING TO QUALIFIED SERVICE
		operating and maintenance
	PERSONNEL.
		(servicing) instructions in the
		literature accompanying the product.
	CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

IMPORTANT INFORMATION

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

CAUTION:

DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE MANUFACTURER OR SOLD WITH THE PRODUCT. FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES RECOMMENDED BY THE MANUFACTURER. A PRODUCT AND CART COMBINATION SHOULD BE MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART COMBINATION TO OVERTURN.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

DECLARATION OF CONFORMITY

SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-37HV4U.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RESPONSIBLE PARTY:

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135

TEL: 1-800-BE-SHARP

For Business Customers: URL http://www. sharpusa. com

INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eia.org

2

DEAR SHARP CUSTOMER

Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years of trouble-free operation of your product, please read the Important Safety Precautions carefully before using this product.

IMPORTANT SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully before using the product.

•Read Instructions — All the safety and operating instructions should be read before the product is operated.

•Retain Instructions — The safety and operating instructions should be retained for future reference.

•Heed Warnings — All warnings on the product and in the operating instructions should be adhered to.

•Follow Instructions — All operating and use instructions should be followed.

•Attachments — Do not use attachments not recommended by the product manufacturer as they may cause hazards.

•Power Sources — This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

•AC Cord Protection — AC cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

•Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

•Object and Liquid Entry — Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

•Servicing — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

•Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)When the AC cord or plug is damaged,

b)If liquid has been spilled, or objects have fallen into the product,

c)If the product has been exposed to rain or water,

d)If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e)If the product has been dropped or damaged in any way, and

f)When the product exhibits a distinct change in performance – this indicates a need for service.

•Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

•Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

•Wall or ceiling mounting — When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

•Polarization — The product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the AC outlet only one way.

This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the polarized plug.

•Unplug the AC cord from the AC outlet before installing the speakers.

3

IMPORTANT SAFETY PRECAUTIONS

• Cleaning — Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

• Water and Moisture — Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

•Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table

recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

•A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

•Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do

not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

•The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass

pieces in case the panel breaks.

•Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

•The Liquid Crystal panel is a very high technology product with 3,147,264 thin film transistors, giving you fine picture details.

Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.

Precautions when transporting the display

When transporting the display, never carry it by holding onto the speakers. Be sure to always carry the display by two people holding it with two hands-one hand on each side of the display.

4

IMPORTANT SAFETY PRECAUTIONS

•Outdoor Antenna Grounding — If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, Iocation of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

	ANTENNA
	LEAD IN
	WIRE
GROUND
CLAMP
	ANTENNA
ELECTRIC	DISCHARGE UNIT
	(NEC SECTION 810-20)
SERVICE
EQUIPMENT	GROUNDING CONDUCTORS
	(NEC SECTION 810-21)
	GROUND CLAMPS
	POWER SERVICE GROUNDING
	ELECTRODE SYSTEM
NEC —NATIONAL ELECTRICAL CODE	(NEC ART 250, PART H)

• Lighting — For added protection for this television equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the equipment due to lightning and power-line surges.

• Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

5

Contents

IMPORTANT INFORMATION ………………………1 DEAR SHARP CUSTOMER …………………………3 IMPORTANT SAFETY PRECAUTIONS ……………3 Contents ………………………………………………6 Supplied accessories ………………………………7 Preparation ……………………………………………8

Attaching the speakers ………………………… 8 Where to place the System ……………………… 9 Setting the System …………………………… 10 Setting the Display on the wall ……………… 12 Setting the AVC System with the stand ……… 12 Inserting the batteries ………………………… 13 Using the remote control unit ………………… 13

Cautions regarding remote control unit … 13

Part names ………………………………………… 14

Display ………………………………………… 14 AVC System …………………………………… 15 Remote control unit …………………………… 16

Watching TV ……………………………………… 17

Antennas ……………………………………… 17 Cable converter/VCR connection …………… 17 Outdoor antenna connection ………………… 19 Connecting the AC cord ……………………… 20 Turning on the power ………………………… 21 Turning off the power ………………………… 21 Initial setup ……………………………………… 22 Simple button operations

for changing channels …………………… 23 Simple button operations

for changing volume/sound ……………… 24 Using FRONT SURROUND

on the remote control unit ………………… 25 Setting MTS/SAP stereo mode ……………… 25

Basic adjustment settings ……………………… 26

AV input mode menu items …………………… 26 PC input mode menu items …………………… 26 EZ setup ………………………………………… 27 Channel setup ………………………………… 28 Language setting ……………………………… 31 Picture adjustments …………………………… 32

C.M.S. (Color Management System) …… 33 Color temperature ………………………… 34 Black ……………………………………… 34 3D-Y/C ……………………………………… 35 Monochrome ……………………………… 35 Film mode (3:2 pull-down) ……………… 36 I/P Setting ………………………………… 36

Sound adjustment ……………………………… 37 Power control …………………………………… 38 Power control for AV source ……………… 38 Power control for PC source ……………… 40

Using external equipment	……………………… 41
Watching a DVD image	……………………… 42
Connecting a DVD player ………………… 42
Displaying a DVD image ………………… 42
Watching a VCR image	……………………… 43
Connecting a VCR ………………………… 43
Displaying a VCR image ………………… 43
Watching broadcasts via a Digital TV tuner … 44
Connecting a Digital TV tuner …………… 44
Displaying broadcasts
via a Digital TV tuner ………………… 44
Enjoying a game console
or viewing camcorder images …………… 45
Connecting a game console
or camcorder ………………………… 45
Displaying an image of the game
console or camcorder ……………… 45
Viewing an image from a PC ………………… 46
Connecting a PC ………………………… 46
Displaying an image from a PC ………… 46

Useful adjustment settings ……………………… 47

Image position (AV input mode only) ……… 47 Moving the picture on the screen …………… 48 Auto Sync. adjustment (PC input mode only) … 49 Fine Sync. adjustment (PC input mode only) … 49 Input signal source …………………………… 50 Picture flip ……………………………………… 51 AV MODE ……………………………………… 52 View modes for 4:3 Programs ………………… 52 View mode (for PC input mode) ……………… 53 Input signal (for PC input mode) …………… 54 Noise clean …………………………………… 54 Sleep timer ……………………………………… 55 Audio out ……………………………………… 55 Connecting external speakers ……………… 56

Selecting speakers ……………………… 57 Cool climate …………………………………… 58 Closed caption ………………………………… 59 Secret number setting for parental control

(AV input mode only) ……………………… 60 Parental control (setting V-CHIP level) ……… 62 How to temporarily release

the V-CHIP BLOCK ……………………… 66 Reactivating the temporarily released

V-CHIP BLOCK …………………………… 66

Other viewing options …………………………… 67

Twin picture functions ………………………… 67 Learning remote control function …………… 68 Using the TV remote control unit

to control other devices …………………… 70

Appendix ………………………………………… 76

Troubleshooting ………………………………… 76 PC compatibility chart ………………………… 77 RS-232C port specifications ………………… 78 Specifications ………………………………… 80 Optional accessories ………………………… 80

Dimensional drawings …………………………… 81

6

Supplied accessories

Make sure the following accessories are provided with the product.

Remote control unit (g1)

“AA” size Alkaline battery (g2)

Cable clamp (Large g1, Small g2)

1 2 3

4 5 6

7 8 9

0 100

VOL

CH

RRMCGA037WJSA	UBATA0018CEZZ
Page 13	Page 13
Stand unit (for AVC System) (g1)	Speaker unit (g1)

GDAI-A059WJSA

PSPAHA101WJZZ

RSP-ZA027WJN1 (Left)

RSP-ZA027WJN2 (Right)

GLEGGA013WJZZ

			XBBSF40P25000
	XBPSN40P14JS0
	Stand (g1)
	Stand cushion (g4)		Speaker (Lg1, Rg1)
	Stand spacer (g4)
	Stand screw (g2)		Speaker screw (g4)
	Page 12		Page 8

	Operation manual (g1)	RF cable (g1)
	LC-37HV4U
	TINS-A529WJZZ	QCNW-A342WJZZ
		Pages 18 and 19

LHLDW0110CEZZ (Large)

LHLDZ0139CEZZ (Small)

Page 11

System cable (g1)

QCNW-6117CEZZ

Page 10

AC cord (g2)

(for Display)

QACCDA019WJPZ

(for AVC System)

QACCD3097CEPZ

Page 10

NOTE

•Always use the AC cord supplied with the Liquid Crystal Television and the one supplied with the AVC System for each respective unit.

•AC cords enclosed in this product are for 110-125V. In using it on the 125240V AC, please consult to the following.

SHARP ELECTRONICS CORPORATION

1300 Naperville Drive, Romeoville, Illinois 60446-1091, U.S.A.TEL: [phone]

7

Preparation

Attaching the speakers

The supplied speaker unit can be attached to or detached from the Display. It must be attached unless you use external amplifier/speakers.

Before attaching (or detaching) speakers, unplug the AC cord from the AC outlet.

Be sure to attach or detach the speakers with two or more people.

Example: Attaching right speaker.

1

Speaker plug

Insert the speaker plug into the terminal on the Display.

•Make sure that the speaker plug is inserted completely.

2

Hole

Hole

Bulge Bulge

Take hold of the speaker and slowly slide it to the Display.

•Make sure that the two bulges of the speaker align with the holes on the Display.

CAUTION

3

Fasten the screws to secure the speaker in place.

•Use a screwdriver.

•Perform the same steps for attaching left speaker.

•The speaker terminals on the Display are only for the supplied speaker unit. Do not connect any third party plug to the terminal or speaker to the Display.

•Do not handle or move the Display by the speakers.

NOTE

•Perform the same steps for both left and right speakers.

•To detach the speakers, perform the above steps in reverse order.

•You can connect your own amplifier/speakers to the Display. See page 56 for connecting external speakers.

8

Preparation

Where to place the System

“System” means the Display and AVC System. First select the location where to place the System.

1 Selecting the location of the System

• Select a place with no direct sunlight and good ventilation.

• The Display and the AVC System are connected by the system cable. (See page 10 for details.)

		System cable	AVC System
	Display	If you want to keep a longer distance between
		the Display and AVC System, please purchase
		the optional system cable AN-07SC1 (about 23
		feet/7 meters). (See page 80.)

2 Setting the System in place

Handling the Display

CAUTION

• The Display is very heavy. Move it with two or more people.

• Do not remove the stand from the Display unless using an optional bracket to mount it.

• When moving, put your hands on the Display, but never on the Display speakers.

• Keep enough space above and behind the Display.

Handling the AVC System

CAUTION

CAUTION		Adjust the screen with both
• Do not put a VCR or other device on the AVC System.		hands. Put one hand on the
		Display and tilt the screen
• Keep enough space above and on the sides of the AVC System.
		while steadying the stand
• Do not block the ventilation openings on the top and left side,		with your other hand.
		You can adjust the screen
and the exhaust fan on the right side.
		vertically up to 4 degrees
• Do not spread a thick cloth beneath the AVC System, or cover it
		forward or 6 degrees back-
with one, as this can cause overheating and result in malfunction.		ward, or rotate 10 degrees
		horizontally.
4 inches
(10 cm)
or more
Keep enough space
2 inches (5
5 cm or more	2 inches (5
cm) or more
	cm) or more
	5 cm or more
on both sides
		There is an exhaust
		fan on the right side.

9

Preparation

Setting the System

After putting the Display and the AVC System in place, connect the system cables and AC cords. Use the cable clamps for bundling the cables.

1 Removing the terminal cover

Display (rear view)

Press the two hooks toward the center of the Display and remove the cover toward you.

Press down the two upper hooks to remove the cover toward you.

2 Connecting the system cable and the AC cord to the Display

DISPLAY INPUT1 DISPLAY INPUT2

	(WHITE)	(GRAY)
	Connect the plug into	Connect the plug firmly
AC cord	the terminal and secure System cable	until the hooks on both
	it by tightening the	sides click.

thumb screws.

3 Connecting the system cable and the AC cord to the AVC System

System cable

(GRAY) (WHITE)

AVC System (rear view)

AC cord

CAUTION

• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH UN-INSULATED PARTS OF ANY CABLES WITH THE

10	AC CORD CONNECTED.

Preparation

4 Attaching the clamps and bundling the cables with the clamp

Cable clamp (Large)

Insert the cable clamp in the hole on the Display leg as shown.

Cable clamp (Small)

Peel off the seal on the back and attach as shown.

Display (rear view)

NOTE

•The small clamp on the right is used for bundling external speakers. (See page 56.)

5 Closing the terminal cover

Cables come out from the small opening.

11

Preparation

Setting the Display on the wall

Using an optional bracket to mount the Display

•You can ask a qualified service personnel about using an optional AN-37AG1 bracket to mount the Display to the wall.

•Carefully read the instructions that come with the bracket before beginning work.

Hanging on the wall

AN-37AG1 wall mount bracket. (See the bracket instructions for details.)

Vertical mounting

Angular mounting

CAUTION

•Installing the Liquid Crystal Television requires special skill that should only be performed by qualified service personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that results in accident or injury.

Setting the AVC System with the stand

How to install the AVC System vertically using the stand unit.

• Use the supplied stand unit for installing the AVC System vertically in an upright position.

Stick each spacer to the		Attach each cushion to		Fit the stand to the AVC
1 stand as shown.		2 the stand as shown.		3 System.
Peel each spacer		Peel each cushion		Insert the stand into the AVC
				System, making sure that the
away from the		away from the
				thick and thin bulges of the
paper and attach	Stand	paper and attach
				stand align with the big and
to the four bulging		to the four areas at
	spacer		Stand cushion	small holes on the AVC
areas on the stand.		the bottom.
	Bulge			System.
			Attaching point	Thin bulge
Bulge				Small	Thick
		Attaching point			bulge
				hole
				Big hole
Attach the stand using the		The AVC System installed
4 stand screws as shown.		vertically with the stand.
	Stand screw

NOTE

•When mounting the AVC System vertically, always use the supplied stand. Be careful not to block vent holes when standing up directly on the floor or a flat surface as this can result in equipment failure.

12

Preparation

Inserting the batteries

If the remote control fails to operate Liquid Crystal Television functions, replace the batteries in the remote control unit.

1 Open the battery cover.	2 Insert two	“AA” size	Alkaline	3 Close the battery cover.
	batteries	(supplied	with the
	product).

_

+

+

_

•Place the batteries with their terminals corresponding to the (e) and (f) indications in the battery compartment.

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

•Do not use manganese batteries. When you replace the batteries, use alkaline ones.

•Place the batteries with their terminals corresponding to the (e) and (f) indications.

•Do not mix batteries of different types. Different types of batteries have different characteristics.

•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

•Remove batteries as soon as they are worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.

•The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

•If you will not be using the remote control unit for an extended period of time, remove batteries from it.

Using the remote control unit

Use the remote control unit by pointing it towards the remote control sensor on the Display. Objects between the remote control unit and the remote control sensor may prevent proper operation.

Cautions regarding remote control unit

• Do not expose the remote control unit to shock.

In addition, do not expose the remote control unit to liquids, and do not place in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The heat may cause deformation of the remote control unit.

• The remote control unit may not work properly if the remote control sensor on the Display is under direct sunlight or strong lighting. In such cases, change the angle of the lighting or the Display, or operate the remote control unit closer to the remote control sensor.

13

Part names

Display

VOLUME buttons

INPUT

MAIN POWER

(VOLl/k)

button

button

CHANNEL buttons

POWER button

(CHs/r)

Remote control sensor

OPC sensor

OPC indicator*

*OPC: Optical Picture Control

(See pages 38 and 40.)

POWER indicator

14

Part names

AVC System	PC INPUT terminal (AUDIO)						Headphone
Front view							(When connecting headphones, the sound from the
			PC INPUT terminal (ANALOG RGB)				speakers is muted.)

How to open the door.

INPUT 4 terminals (AUDIO L/R)

STANDBY/ON indicator

INPUT 4 terminal (VIDEO)

CLEAR*

MAIN POWER button		INPUT 4 terminal (S-VIDEO)

*If the AVC System is switched on but it does not appear to be operating correctly, it may need resetting. In this case, press CLEAR, shown in the diagram, lightly with the end of a ballpoint pen or other pointed object. This will reset the System as shown below.

•AV MODE resets to USER

•TV channel returns to initial channel setting (Air:2ch, Cable:1 or 2ch)

•Twin picture resets to normal

•Audio setting initializes

•SRS resets to off

•Image position initializes

NOTE

•Pressing CLEAR will not work if the System is in standby mode (indicator lights red).

•Pressing CLEAR will not delete channel preset or secret number. See page 61 for clearing the secret number when you know it. See page 83 for initializing to the factory preset values when you forget your secret number.

Rear view	DC OUTPUT terminal
	(Terminal for expanded functionality in

		the near future.)		DISPLAY OUTPUT 2 terminal
Antenna (A) input terminal		DVI-DIGITAL	RS-232C	DISPLAY OUTPUT 1 terminal
Antenna (A) output
	Antenna (B)	INPUT	terminal	AC INPUT terminal
terminal	input terminal	terminal

INPUT 2 terminal (VIDEO)

INPUT 2 terminal (S-VIDEO)

INPUT 1 terminal (S-VIDEO)

INPUT 1 COMPONENT video terminals (Y, PB, PR)

INPUT 1 terminal (VIDEO)

INPUT 1 terminals (AUDIO L/R)

INPUT 2 terminals (AUDIO L/R)

INPUT 3 COMPONENT video terminals (Y, PB, PR)

INPUT 3 terminals (AUDIO L/R)

INPUT 3 terminal (S-VIDEO)

INPUT 3 terminal (VIDEO)

MONITOR OUTPUT terminal (S-VIDEO)

MONITOR OUTPUT terminal (VIDEO)

MONITOR OUTPUT terminals (AUDIO L/R)

15

Part names

Remote control unit

24 25

1 12 13 14

2		/DTV			15
		TV CBL VCR DVD
	TV	/SAT	/LD
	POWER	ANT-A/B	INPUT
3	AV	FRONT			16
	MODE	SURROUND	MTS	CC
		TWIN
		PICTURE	SELECT		17
4	VIEW		SUB	TWIN CH
	MODE	FREEZE	INPUT
5	DISPLAY	SLEEP	EDIT/	LEARN
	1	2		3
6	4	5		6	18
	7	8		9
7		0	100 ENT		19
		FLASHBACK			20
8	VOL			CH
		MUTE
9					21
	MENU	TV/SAT/DVD		DTV/DVD TOP
10
	RETURN	MENU		MENU
	SOURCE			DTV/SAT
	POWER			GUIDE
11		SET/			22
		ENTER		DTV/SAT
				INFO
		FAVORITE CH		VCR REC	23
	A	B	C	D
	POWER	INPUT VOL VOL
		RECEIVER

NOTE

•When using the remote control unit, point it at the Liquid Crystal Television.

•See pages 68 to 75 for operating buttons not listed on this page.

* is a trademark of SRS Labs, Inc.

FOCUS technology is incorporated under license from SRS Labs, Inc.

1TV POWER: Switch the Liquid Crystal Television power on or off. (See page 21.)

2FRONT SURROUND: Set SRS* and FOCUS* Sound System mode. (See page 25.)

3AV MODE: Select an audio or video setting. (See

page 52.) (AV mode: STANDARD, DYNAMIC, MOVIE, GAME, USER. PC mode: STANDARD, USER.)

4VIEW MODE: Select the screen size. (See pages 52 and 53.)

5DISPLAY: Display the channel information.

6SLEEP: Set the sleep timer. (See page 55.)

7FLASHBACK: Return to the previous channel or input external mode. (See page 23.)

8VOL k/l: Set the volume. (See page 24.)

9MENU: Display the menu screen.

10MENU RETURN: Return to the previous menu screen.

11a/b/c/d: Select a desired item on the screen.

12ANT-A/B: Select between ANT-A and B to watch broadcasts via the two tuners.

13INPUT: Select a Liquid Crystal Television input source.

(TV, INPUT 1, INPUT 2, INPUT 3, INPUT 4, PC) (See pages 42–46 and 50.)

14: When pressed all buttons on the remote control unit will light. The lighting will turn off if no operations are performed within about 5 seconds. This button is used for performing operations in dark places.

15MTS: Select the MTS/SAP. (See page 25.)

16CC: Display captions during closed-caption source. (See page 59.)

17TWIN CH buttons

TWIN PICTURE: Set the twin picture mode. Press again to return to normal screen. (See page 67.)

FREEZE: Set the still image. Press again to return to normal screen. (See page 67.)

SELECT: Select the active screen. (See page 67.) SUB INPUT: Select an input source of sub screen.

(See page 67.)

TWIN CH a/b: Select the channel of sub screen. (See page 67.)

180 – 9: Set the channel.

19100 ENT: Select the three digit mode. Execute a command of the channel.

20CH a/b: Select the channel.

21MUTE: Mute the sound. (See page 24.)

22SET/ENTER: Execute a command.

23FAVORITE CH

A, B, C, D: Select four preset favorite channels in four different categories. (See page 30 for details.)

When viewing via ANT-A: up to 16 channels can be assigned in A, B, C and D.

When viewing via ANT-B: up to 16 channels can be assigned in A, B, C and D.

With ANT-A and B combined, you can preset up to 32 favorite channels in advance.

While watching, you can toggle the selected channels by pressing A, B, C and D.

24LED for transmission confirmation

25Mode switch: (See pages 68 to 75 for details.)

16

Watching TV

Simple operations for watching a TV program

Antennas

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the AVC System.

NOTE

• The antenna and the cable converter cannot be connected at the same time.

1.A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (not supplied).

2.A 300-ohm system is a flat “twin-lead” cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (not supplied).

F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (flat)

Cable converter/VCR connection

•Be sure to connect the antenna or the cable converter as follows. Signal reception may fail if improperly connected.

•Be sure to remember what kind of connection is made with your System.

•The connection type will determine whether to select “Air” or “Cable” for both ANT-A and B when configuring “Air/Cable” settings.

A-1. Connecting with Converter/Descrambler Box and VCR

Coaxial Antenna Cable (commercially available)

Coaxial Antenna Cable (commercially available)

Rear Terminals

		2-way
		signal
		splitter
OUT	IN	(not
Cable TV converter		supplied) Cable lead-in
(not supplied)
		Coaxial Antenna Cable (commercially available)
		VCR

S-VIDEO VIDEO AUDIO

OUT

IN

Video Cable (commercially available)

Audio Cable (commercially available)

S-video Cable (commercially available)

NOTE

•Be sure to remember what kind of connection is made with your System.

•Shown here is the preferred method of connecting a VCR and CATV Converter to your TV if you are in an area with good signal reception. This way you can view either TV programs or VCR tapes and not be concerned about the position of the VCR’s TV/VCR switch and you can enjoy stereo tape playback from a stereo VCR.

•If your VCR has an S-Video terminal, S-video connection is recommended.

17

Watching TV

Cable converter/VCR connection (continued)

A-2. Connecting with cable converter using AUX terminals for audio and video output.

(If your cable TV converter has both RF OUTPUT and AUX terminals, it is recommended to connect it as shown in example A-1.)

	RF
	Cable	Coaxial Antenna Cable (commercially available)
	(Supplied)
					2-way
					signal
		Rear Terminals			splitter
			OUT	IN	(not
					supplied) Cable lead-in
			VIDEO AUDIO
					Cable TV converter
					(not supplied)

VCR

S-VIDEO VIDEO AUDIO

OUT

IN

Video Cable (commercially available)

Audio Cable (commercially available)

S-video Cable (commercially available)

NOTE

•Be sure to remember what kind of connection is made with your System.

•Shown here is the preferred method of connecting a VCR and CATV Converter to your TV if you are in an area with good signal reception. This way you can view either TV programs or VCR tapes and not be concerned about the position of the VCR’s TV/VCR switch and you can enjoy stereo tape playback from a stereo VCR.

•If your VCR has an S-Video terminal, S-video connection is recommended.

B.Connecting with Converter/Descrambler Box without VCR

Coaxial Antenna Cable (commercially available)

Coaxial Antenna Cable (commercially available)

Rear Terminals

		2-way
		signal
		splitter
OUT	IN	(not
Cable TV converter		supplied) Cable lead-in
(not supplied)

Coaxial Antenna Cable (commercially available)

NOTE

•Be sure to remember what kind of connection is made with your System.

•Switching between Antenna-A and Antenna-B is possible by pressing the ANT-A/B button on the remote control.

•A good color picture depends on a good TV signal. So does good multi-channel sound. Ask your dealer for advice on how to install your outdoor antenna to receive the best possible signal.

•If you subscribe to Cable TV or have a central antenna for your building, you may not need an outdoor antenna.

18

Watching TV

C.Connecting Antenna Cable with VCR

RF Cable (Supplied)

Rear Terminals	Coaxial Antenna Cable (commercially available)
	2-way
	signal
	splitter
	(not
	supplied) Cable lead-in
	Coaxial Antenna Cable
	(commercially available)

VCR

S-VIDEO VIDEO

AUDIO

OUT

IN

Video Cable (commercially available)

Audio Cable (commercially available)

S-video Cable (commercially available)

NOTE

•Be sure to remember what kind of connection is made with your System.

•Shown here is the preferred method of connecting a VCR to your TV if you are in an area with good signal reception. This way you can view either TV programs or VCR tapes and not be concerned about the position of the VCR’s TV/VCR switch and you can enjoy stereo tape playback from stereo VCR.

•If your VCR has an S-Video terminal, S-video connection is recommended.

•If your lead cable is a 300-ohm twin-lead cable or UHF/VHF separate cable, use a 300/75-ohm adapter or combiner (output side is 75-ohm coaxial) to connect to the TV (see below).

Outdoor antenna connection

Connecting Antenna Cable

Cable without a CATV converter

Combination

VHF/UHF antenna

Separate VHF/UHF

antenna

Cable TV lead-In

or 75-ohm coaxial cable (round)

300/75-ohm adapter

(commercially available)

300-ohm twin-lead (flat)

VHF UHF

ANTENNA ANTENNA

300-ohm

twin-lead

Combiner

(commercially

available)

300-ohm twin-lead IN OUT

or

75-ohm coaxial cable

Home Antenna terminal (75-ohm)

Coaxial cable	RF Cable (Supplied)
(commercially
available)

NOTICE

F-type connector

75-ohm coaxial cable

F-type connector should be finger-tightened only.

When connecting the RF cable to the TV set, do not tighten F-type connector with tools. If tools are used, it may cause damage to your TV set.

(The breaking of internal circuit, etc.)

19

Watching TV

Connecting the AC cord

Connect the AC cords after all component connections have been completed.

Display (rear view)

AC cord

AVC System (rear view)

AC cord

NOTE

•Always turn off the main power of the Display and AVC System when connecting the AC cords.

•Disconnect the AC cords from the AC outlet, Display and AVC System when the System is not going to be used for a long period of time.

20

Watching TV

Display

Turning on the power

POWER button

MAIN POWER

POWER indicator

AVC System

MAIN STANDBY/ON indicator

POWER

	TV CBL	VCR DVD
TV	/SAT	/LD
	/DTV
POWER	ANT-A/B	INPUT
AV	FRONT
MODE	SURROUND	MTS	CC
	TWIN
	PICTURE	SELECT
VIEW		SUB	TWIN CH
MODE	FREEZE	INPUT
DISPLAY	SLEEP	EDIT/	LEARN

1	2	3
4	5	6
7	8	9
	0	100 ENT

1 Press MAIN POWER on the Display.

• The POWER indicator on the Display flashes red.

2 Press MAIN POWER on the AVC System.

•The System turns the power on.

•The POWER indicator on the Display lights up green and the STANDBY/ON indicator on the AVC System lights up green.

•If the STANDBY/ON indicator on the AVC System and the POWER indicator on the Display still light up red, press TV POWER on the remote control unit or MAIN POWER on the AVC System to turn the System on.

First time turning on the AVC System

1 Press MAIN POWER on the AVC System.

• The STANDBY/ON indicator on the AVC System lights up red.

2 Press MAIN POWER on the Display.

•The System turns the power on.

•The POWER indicator on the Display lights up green and the STANDBY/ON indicator on the AVC System lights up green.

•If the STANDBY/ON indicator on the AVC System and the POWER indicator on the Display still light up red, press TV POWER on the remote control unit or POWER button on the Display to turn the System on.

NOTE

•The initial setup starts when the System powers on for the first time. If the System has been turned on before, the EZ setup will not be invoked. See page 27 to try EZ setup from the Setup menu.

Turning off the power

1 Press TV POWER on the remote control unit or POWER button on the Display.

•The System enters standby mode and the image on the screen disappears.

•Both the STANDBY/ON indicator on the AVC System and the POWER indicator on the Display change from green to red.

2 Press MAIN POWER on the AVC System.

•The STANDBY/ON indicator on the AVC System turns off and the POWER indicator on the Display flashes red.

3 Press MAIN POWER on the Display.

• The POWER indicator on the Display gradually turns off.

NOTE

Display status indicator

•If you are not going to use this System for a long period of time, be sure to remove the AC cords from the power outlet.

•When the STANDBY/ON indicator lights up red, it takes about 10 to 15 seconds for the indicator to turn off if MAIN POWER on the AVC System is turned “Off” or the AC cord is unplugged from the AC outlet.

Off	Power off
Flashing red	AVC System does not turn on or its AC cord is disconnected.
Red	The System is in standby mode.
Green	The System is on.

AVC System status indicator

Off	Power off
Red	Only the AVC System is in standby mode or the System is in standby mode.
Green	The System is on.

21

Watching TV

Initial setup

When you turn on the System for the first time, it will automatically memorize the broadcasting channels where you live. Perform the following steps before you press TV POWER on the remote control unit.

1.Insert the batteries into the remote control unit. (See page 13.)

2.Connect the antenna cable to the AVC System. (See pages 17 to 19.)

3.Plug in the AC cord to the AC outlet. (See page 20.)

Language setting

Select from among 3 languages: English, French and Spanish.

1 Press a/bto select the desired language listed on the screen, and then press SET/ ENTER.

Setup

EZ Setup - Language

English

Français

Español

MENU	TV/SAT/DVD		DTV/DVD TOP
RETURN		MENU	MENU
SOURCE			DTV/SAT
POWER			GUIDE
		SET/
	ENTER		DTV/SAT
			INFO
	FAVORITE CH		VCR REC
A	B	C	D
POWER	INPUT	VOL	VOL

RECEIVER

Channel search

Channel auto search makes the System look for all channels viewable in the set area.

Antenna setting

NOTE

•Make sure what kind of connection is made with your System when selecting “Air” or “Cable” for both ANT-A and B.

2 Press c/dto select “Air” or “Cable” for ANT- A, then press a/bto move down.

Press c/dto select “Air” or “Cable” for ANT- B.

Press SET/ENTER to enter the setting.

•This operation makes the System search for both ANT-A and B.

Example

Setup

EZ Setup - Air/Cable

ANT-A	Air	Cable
ANT-B	Air	Cable

Setup

EZ Setup - Air/Cable

ANT-A	Air	Cable
ANT-B	Air	Cable

3

Example

CH Search

ANT-A Air [ 2 ]

CH Search

ANT-B Cable [ 2 ]

2 ANT-A

Noise Clean

NOTE

•Make sure what kind of connection is made with your System when selecting “Air” or “Cable” for both ANT-A and B.

•If no channel is found, make sure what kind of connection is made with your System and try EZ setup again (see page 27).

•The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the actual operations.

22

Watching TV

Simple button operations for changing channels

You can change channels in several ways.

NOTE

Using FLASHBACK on the remote control unit

Press FLASHBACK to switch the currently tuned channel to the previously tuned channel.

Press FLASHBACK again to switch back to the currently tuned channel.

•While watching a broadcast, press ANT-A/B to view the image received from the other tuner.

	TV CBL	VCR DVD
TV	/SAT	/LD
	/DTV
POWER	ANT-A/B	INPUT
AV	FRONT
MODE	SURROUND	MTS	CC
	TWIN
	PICTURE	SELECT
VIEW		SUB	TWIN CH
MODE	FREEZE	INPUT
DISPLAY	SLEEP	EDIT/	LEARN

1	2	3
4	5	6

NOTE

•FLASHBACK will not work if no channel has been changed after the System is turned on.

Using 0 – 9 and 100 on the remote control unit

Select the channels directly by pressing buttons 0 to

9 and 100.

•The System allows you to select up to 125 channels (1 to 125). To select a channel, enter a 2 or 3-digit number.

a

To select a 1 or 2-digit channel number (e.g., Channel 5):

Complete the following steps within 3 seconds.

7 8 9

0

100 ENT

FLASHBACK

VOL

CH

MUTE

Using CHa/bon the remote control unit

•Press CHato increase the channel number.

•Press CHbto decrease the channel number.

NOTE

•CH s/ron the Display operates the same as CHa/b on the remote control unit.

1 Press the 0 button.

•Complete the step 2 within 3 seconds after the step 1.

2 Press the 5 button.

0–

5

NOTE

•When selecting a 1-digit channel number, do not fail to press the 0 button.

To select a 3-digit channel number (e.g., Channel 115):

Complete the following steps within 3 seconds.

Display

CH s/r

Changing channels with CH a/bon the remote control unit or CH s/ron the

Display

Air: Press CH a and the channel change in the order shown below: 2s3s...s68s69s2s3...

Press CH band the channel change in the order shown below:

3s2s69s68s...s3s2...

Cable:Press CH a and the channel change in the order shown below: 1s2s3s...s125s1s2s3...

Press CH band the channel change in the order shown below: 3s2s1s125s...s3s2s1s...

1 Press the 100 button.

•Complete the step 2 within 3 seconds after the step 1.

2 Press the 1 button.

•Complete the step 3 within 3 seconds after the step 2.

3 Press the 5 button.

1––

11–

115

NOTE

•The 100 button is only enabled when selecting channels in Cable mode.

23

Watching TV

Simple button operations for	Using MUTE on the remote control unit
changing volume/sound	Mutes the current sound output.
Changing the volume

You can change the volume on the Display or on the remote control unit.

Display

VOL l/k

	FLASHBACK
VOL		CH
	MUTE
MENU	TV/SAT/DVD	DTV/DVD TOP
RETURN	MENU	MENU

Using VOL k/lon the remote control unit

•To increase the volume, press VOL k.

•To decrease the volume, press VOL l.

Volume adjustment

	TV CBL	VCR DVD
TV	/SAT	/LD
	/DTV
POWER	ANT-A/B	INPUT
AV	FRONT
MODE	SURROUND	MTS	CC
	TWIN
	PICTURE	SELECT
VIEW		SUB	TWIN CH
MODE	FREEZE	INPUT
DISPLAY	SLEEP	EDIT/	LEARN

1	2	3
4	5	6
7	8	9
	0	100 ENT

FLASHBACK

VOL

CH

MUTE

MENU	TV/SAT/DVD	DTV/DVD TOP
RETURN	MENU	MENU

20

NOTE

•VOL l/kon the Display operates the same as VOL k/l on the remote control unit.

Audio status

	Output device	Audio out
		Fixed	Variable
	Speaker	Variable sound	Mute
	MONITOR OUT	Constant as	Variable sound
		specified

*When “Audio Out” is set to “Variable”, the indicator on the screen changes as shown below.

20

NOTE

• See page 55 for details on the audio out function.

1 Press MUTE.

•“M” has been displayed on the screen for 30 minutes, and the sound is silenced.

Mute

0

NOTE

•Within 30 minutes of pressing MUTE, mute can be canceled by using one of the methods below.

•Pressing VOL l/kon the Display or VOL k/l, MTS or MUTE on the remote control unit can also cancel the mute.

•Mute will be canceled after 30 minutes have passed. However, the System will not suddenly output a loud sound as the volume level is set to 0 automatically.

2 Within 30 minutes, press MUTE again to cancel the mute.

•Before 30 minutes, the volume level returns to the previous setting.

•After 30 minutes, increase the volume level by pressing VOL k.

24

Watching TV

Using FRONT SURROUND on the remote control unit

h produces SRS and FOCUS effects from the speakers.

Each time you press FRONT SURROUND, the mode changes among SRS, FOCUS, FOCUS e SRS and Off.

TV CBL VCR DVD TV /SAT /LD

/DTV

POWER ANT-A/B INPUT

AV FRONT

MODE

SURROUND

MTS

CC

TWIN

PICTURE SELECT

SRS sound options

•SRS (Sound Retrieval System): Creates more a natural sound retrieving the spatial information from any stereo recording and restoring the original threedimensional sound field.

•FOCUS: Repositions a sound image from two speakers to a more optimal listening position or height without moving them.

•FOCUS eSRS: Produces both SRS and FOCUS effects.

•Off: Outputs the normal sound.

: Off	: SRS
: FOCUS+SRS	: FOCUS

Setting MTS/SAP stereo mode

The System has a feature that allows reception of sound other than the main audio for the program. This feature is called Multi-channel Television Sound (MTS). The System with MTS can receive mono sound, stereo sound and Secondary Audio Programs (SAP). The SAP feature allows a TV station to broadcast other information, which could be audio in another language or something completely different like weather information.

You can enjoy Hi-Fi stereo sound or SAP broadcasts where available.

•Stereo broadcasts

View programs like live sporting events, shows and concerts in dynamic stereo sound.

•SAP broadcasts

Receive TV broadcasts in either MAIN or SAP sound. MAIN sound: The normal program soundtrack (either in mono or stereo).

SAP sound: Listen to second language, supplementary commentary and other information. (SAP is mono sound.)

If stereo sound is difficult to hear.

•Obtain a clearer sound by manually switching to fixed mono-sound mode.

NOTE

•Once “MONO” mode is selected, the sound remains mono even if the System receives a stereo broadcast. You must switch the mode back to “STEREO” if you want to hear stereo sound again.

•Selecting MTS while in the input mode does not change the type of sound. In this case, sound is determined by the video source.

	TV CBL	VCR DVD	Each time you press
			MTS, MTS toggles as
	/DTV
TV	/SAT	/LD	shown below.
POWER	ANT-A/B	INPUT
AV	FRONT
MODE	SURROUND	MTS	CC
	TWIN
	PICTURE	SELECT
VIEW		SUB	TWIN CH
MODE	FREEZE	INPUT

Examples: when receiving MTS and SAP

STEREO mode

MAINkSAP mode

STEREOkSAP mode

MONO mode

38

ANT-A

38

ANT-A

38

ANT-A

38

ANT-A

STEREO

MAIN

ST(SAP)

MONO

38

ANT-A

38

ANT-A

38

ANT-A

38

ANT-A

STEREO

SAP

SAP(ST)

MONO

38

ANT-A

38

ANT-A

38

ANT-A

38

ANT-A

MONO

MONO

MONO

MONO

25

Basic adjustment settings

AV input mode menu items

List of AV menu items to help you with operations

			Picture
	Contrast			Page 32
	Brightness .....................................			Page 32
	Color ...............................................			Page 32
	Tint .................................................			Page 32
	Sharpness ......................................			Page 32
	Advanced
	C.M.S. ...................................			Page 33
	Color Temp ..........................			Page 34
	Black ....................................			Page 34
	3D-Y/C ..................................			Page 35
	Monochrome .......................			Page 35
	Film Mode ............................			Page 36
	I/P Setting ............................			Page 36

PC input mode menu items

List of PC menu items to help you with operations

			Picture
	Contrast			Page 32
	Brightness .....................................			Page 32
	Red .................................................			Page 32
	Green ..............................................			Page 32
	Blue ................................................			Page 32
	C.M.S. .............................................			Page 33

Audio

Audio

	Treble	Page 37				Treble	Page 37
	Bass ...............................................	Page 37				Bass ...............................................	Page 37
	Balance ..........................................	Page 37				Balance ..........................................	Page 37
	Speaker ..........................................	Page 57				Speaker ..........................................	Page 57

				Power control
	Power Save				Page 38
	No Signal Off .................................				Page 39
	No Operation Off			...........................	Page 39

Power control

	Power Save	Page 40
	Power Management ......................	Page 40

Setup

Setup

	EZ Setup	Page 27
	CH Setup .................................	Pages 28-30
	Input Signal ...................................	Page 50
	Parental CTRL ........................	Pages 60-66
	Position ..........................................	Page 47
	Picture Flip ....................................	Page 51
	Language .......................................	Page 31

	Input Signal	Page 54
	Auto Sync. .....................................	Page 49
	Fine Sync. ......................................	Page 49
	Picture Flip ....................................	Page 51
	Language .......................................	Page 31

Option

Option

	Input Select	Page 50				Audio Out	Page 55
	Noise Clean ...................................	Page 54				Cool Climate ..................................	Page 58
	Audio Out .......................................	Page 55
	..................................Cool Climate	Page 58

26