POSITIVE DISPLACEMENT HIGH FLOWMETERS FOR VISCOUS FLUIDS
FPD1004
U0 to 1000 cP Viscosity Standard, 1,000,000 cP Viscosity Rotor
Also Available
UCompact, Durable, and Serviceable On-Site
UExtremely Accurate Even with Viscous Fluids
UMeter Design Minimizes the Number of Wearable Parts—Extending Product Life
UReed Switch or Hall Effect Sensor
UHandles Particle Sizes to 0.28 mm (0.011")
SPECIFICATIONS
Accuracy: ±0.5% rdg Repeatability: ±0.03%
Fitting Type: FNPT, flange and tri-clover sanitary fittings optional on some models
Sensor Options: Reed switch (2-wire SPST reed switch N/O, 3 watts rated, 150 Vdc max) or hall effect sensor (25 mA NPN open collector)
Hall Effect Sensor—Power Requirements: Dedicated 4.5 to 24 Vdc (4.6 to 9 mA)
Maximum Viscosity: 1000 cP
Body: Aluminum; not recommended for water applications
Strainer Size: 60 mesh [handles particle sizes to 0.28 mm (0.011")] Mounting: Shafts must be in a horizontal plane; cap screws should not point up or down
FPD1000D-TX remote 4 to 20 mA output with programmable display (loop powered), shown smaller than actual size.
FPD1004, shown smaller than actual size.
Meter |
Length |
Height |
Size |
mm (inch) |
mm (inch) |
¹⁄ " |
100.0 (3.94) |
96.0 (3.78) |
³⁄ " |
133.0 (5.24) |
126.0 (4.96) |
1" PPS |
107.9 (4.25) |
100.0 (3.94) |
1" AL/SS |
170.1 (6.70) |
112.0 (4.41) |
1¹⁄ " |
212.0 (8.35) |
144.0 (5.67) |
2" |
240.0 (9.45) |
178.0 (7.01) |
|
|
|
Wetted Materials
Housing |
Aluminum (Std) |
Stainless Steel |
PPS |
Bearings for 1" units |
Carbon/graphite |
Carbon/graphite |
PPS |
Bearings for ¹⁄ to 2" units |
PPS |
PPS |
N/A |
Shaft |
316 SS |
316 SS |
Hastelloy C |
Rotor for ¹⁄ , ³⁄ , 1¹⁄ , 2" |
PPS |
PPS |
N/A |
Rotor for 1" units |
316 SS |
316 SS |
PPS |
O-ring |
FKM |
FKM |
PTFE |
|
Weight |
Max Temp |
Max Pressure |
Typical |
Frequency |
|
Meter Size |
kg (lb) |
°C (°F) |
bar (psi) |
K Factors (PPG) |
Range (Hz) |
|
¹⁄ " Aluminum |
1.50 |
(3.25) |
80 (176) |
55 (800) |
424.0 |
1.8 to 55.8 |
¹⁄ " SS |
2.70 (6.0) |
120 (248) |
55 (800) |
424.0 |
1.8 to 55.8 |
|
3⁄4" Aluminum |
1.9 |
(4.3) |
80 (176) |
55 (800) |
197.0 |
2.6 to 51.9 |
1" PPS body |
1.30 (1.3) |
80 (176) |
10 (150) |
197.0 |
2.6 to 69.0 |
|
1" Aluminum |
2.20 (4.9) |
80 (176) |
55 (800) |
136.3 |
3.6 to 72.7 |
|
1" Al w/150# flange |
2.90 (6.6) |
80 (176) |
Flange Rule |
136.3 |
3.6 to 72.7 |
|
1 SS |
5.70 |
(12.7) |
120 (248) |
55 (800) |
136.3 |
3.6 to 72.7 |
1 SS w/150# flange |
6.60 |
(14.6) |
120 (248) |
Flange Rule |
136.3 |
3.6 to 72.7 |
1 SS w/tri-clover fittings |
4.90 |
(10.8) |
120 (248) |
55 (800) |
136.3 |
3.6 to 72.7 |
1¹⁄ " Aluminum |
4.50 |
(10.0) |
80 (176) |
55 (800) |
54.9 |
2.4 to 60.4 |
1¹⁄ Al w/150# flange |
5.40 |
(12.0) |
80 (176) |
Flange Rule |
54.9 |
2.4 to 60.4 |
2" Aluminum |
7.80 |
(17.1) |
80 (176) |
55 (800) |
25.3 |
1.7 to 39.0 |
2" Al w/150# flange |
9.10 |
(20.1) |
80 (176) |
Flange Rule |
25.3 |
1.7 to 39.0 |
F-X