Loading...
B ENGINE
SECTION LU
ENGINE LUBRICATION SYSTEM
CONTENTS
A
LU
C
D
E
PRECAUTIONS ......................................................... |
2 |
Precautions for Liquid Gasket ................................. |
2 |
LIQUID GASKET APPLICATION PROCEDURE..... |
2 |
PREPARATION .......................................................... |
3 |
Special Service Tools .............................................. |
3 |
Commercial Service Tools ....................................... |
3 |
LUBRICATION SYSTEM ........................................... |
4 |
Lubrication Circuit ................................................... |
4 |
System Chart ........................................................... |
5 |
ENGINE OIL .............................................................. |
6 |
Inspection ................................................................ |
6 |
ENGINE OIL LEVEL ............................................ |
6 |
ENGINE OIL APPEARANCE ............................... |
6 |
ENGINE OIL LEAKAGE ....................................... |
6 |
OIL PRESSURE CHECK ..................................... |
6 |
Changing Engine Oil ............................................... |
7 |
OIL FILTER ................................................................ |
9 |
Removal and Installation ......................................... |
9 |
REMOVAL ............................................................ |
9 |
INSTALLATION .................................................... |
9 |
INSPECTION AFTER INSTALLATION ................ |
9 |
OIL COOLER ........................................................... |
10 |
Removal and Installation ....................................... |
10 |
REMOVAL .......................................................... |
10 |
INSPECTION AFTER REMOVAL ...................... |
10 |
INSTALLATION .................................................. |
10 |
INSPECTION AFTER INSTALLATION ............... |
10 |
OIL PUMP ................................................................ |
12 |
Removal and Installation ....................................... |
12 |
REMOVAL .......................................................... |
12 |
INSTALLATION .................................................. |
12 |
INSPECTION AFTER INSTALLATION ............... |
12 |
Disassembly and Assembly ................................... |
12 |
DISASSEMBLY .................................................. |
12 |
INSPECTION AFTER DISASSEMBLY ............... |
13 |
ASSEMBLY ........................................................ |
14 |
SERVICE DATA AND SPECIFICATIONS (SDS) ..... |
15 |
Standard and Limit ................................................. |
15 |
OIL PRESSURE ................................................. |
15 |
ENGINE OIL CAPACITY (APPROXIMATE) ....... |
15 |
OIL PUMP .......................................................... |
15 |
REGULATOR VALVE ......................................... |
15 |
F
G
H
I
J
K
L
M
Revision: 2005 March |
LU-1 |
2005 X-Trail |
PRECAUTIONS
PRECAUTIONS
Precautions for Liquid Gasket
LIQUID GASKET APPLICATION PROCEDURE
PFP:00001
ABS00CJR
1.Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.
●Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt holes.
2.Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating use) to remove adhering moisture, grease and foreign materials.
3.Attach liquid gasket tube to the tube presser [SST: WS39930000 ( — )].
Use Genuine RTV Silicone Sealant or equivalent. Refer to GI-48, "RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS" .
●Within 5 minutes of liquid gasket application, install the mating component.
●If liquid gasket protrudes, wipe it off immediately.
●Do not retighten mounting bolts or nuts after the installation.
●Wait 30 minutes or more after installation before refilling
EMA0622D
engine oil and engine coolant.
Revision: 2005 March |
LU-2 |
2005 X-Trail |
PREPARATION
PREPARATION |
PFP:00002 |
Special Service Tools |
ABS00CJS |
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.) Description Tool name
ST25051001 |
Measuring oil pressure |
(J25695-1) |
Maximum measuring range: |
Oil pressure gauge |
2,452 kPa (25 kg/cm2 , 356 psi) |
|
NT050 |
|
|
ST25052000 |
Adapting oil pressure gauge to oil pan (upper) |
(J25695-2) |
|
Hose |
|
|
S-NT559 |
|
|
KV10115801 |
Removing and installing oil filter |
(J-38956) |
a: 64.3 mm (2.531 in) |
Oil filter wrench |
|
|
S-NT375 |
|
|
WS39930000 |
Pressing the tube of liquid gasket |
( — ) |
|
Tube presser |
|
NT052
A
LU
C
D
E
F
G
H
I
J
K
Commercial Service Tools
ABS00CJT L
Tool name |
Description |
|
|
|
|
Deep socket |
Removing and installing oil pressure switch |
M |
|
a: 27 mm (1.06 in) |
|
|
|
PBIC2072E
Revision: 2005 March |
LU-3 |
2005 X-Trail |
LUBRICATION SYSTEM
LUBRICATION SYSTEM
Lubrication Circuit
PFP:15010
ABS00CJU
PBIC2270E
Revision: 2005 March |
LU-4 |
2005 X-Trail |
LUBRICATION SYSTEM
System Chart
ABS00CJV
PBIC2753E
A
LU
C
D
E
F
G
H
I
J
K
L
M
Revision: 2005 March |
LU-5 |
2005 X-Trail |
Loading...