Page 1
LED DESK LAMP
LED DESK LAMP
Operation and Safety Notes
IAN 93365
Page 2
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
GB / IE Operation and Safety Notes Page 5
Page 3
A
1 2 3 4 5
B
6
1
2
7424-018L-BS
1 2 3 4 5
7425-018L-BS7430-018L-BS
1 2 3 4 5
7424-018L-BS
6
1
2
7425-018L-BS7430-018L-BS
6
1
2
Page 4
C
7
6
1
D
7424-018L-BS
7425-018L-BS7430-018L-BS
2
7
6
1
2
7
6
7424-018L-BS
7425-018L-BS7430-018L-BS
1
2
Page 5
Introduction
The following pictograms are used in these operating instructions / on the device:
Read instruction manual!
Observe warning and safety notes!
Caution – electric shock! Risk of loss of life!
Risk of loss of life by electric shock from damaged mains lead or mains plug!
Warning - Hot surfaces!
V∼
W
Volt (AC)
Watts (Effective power)
Dispose of packaging and appliance in an environmentally friendly way!
LED Desk lamp
Introduction
We congratulate you on the purchase of
your new device. You have chosen a high
quality product. These operating instructions form a part of this product. They contain important information on safety, use and disposal. Make
yourself familiar with all the operating instructions
and safety advice for the product before use. Use
the product only as described and for the indicated
purpose. If you pass the product on to anyone else,
please ensure that you also pass on all the documentation with it. Check that the correct mains voltage is available and that all the parts have been
properly assembled before bringing into use.
Proper use
This lamp is designed for use indoors only, in dry
and enclosed rooms. This product is intended for
use in a private, domestic environment only. Other
uses or modification of the product shall be considered as improper use and could lead to injury or
damage. The manufacturer accepts no liability for
loss or damage arising from improper use.
Included items
Check that all the items and accessories are present
and that the lamp is in perfect condition immediately
after unpacking.
1 x LED Desk Lamp
1 x LED light (E14 / 3.2 W)
1 x Operating instructions
Description of parts and
features
1
Lamp shade
2
Socket
3
ON / OFF switch
4
Power cable
5
Mains plug
6
Threaded ring
7
Light bulb
5 GB/IE
Page 6
Introduction / Safety advice
Technical data
Operating voltage: 220–240 V ∼, 50 Hz
Protection class:
Light bulb: LED E14 / 3.2 W (included)
Rated power: 1 x max 3.2 W
Material: plastic, textile shade
Model:
7424-018L-BS (empire lamp shade)
7425-018L-BS (drum lamp shade)
7430-018L-BS (hexagonal lamp shade)
Safety advice
The right to claim under the guarantee shall be
rendered invalid in respect of damage caused by
the non-observance of these operating instructions!
No liability is accepted for consequent damage! No
liability is accepted for damage to property or persons caused by improper handling or non-observance
of the safety advice!
RISK OF LOSS
OF LIFE AND ACCIDENT TO INFANTS AND CHILDREN! Never
leave children unsupervised with the packaging
materials. Packaging materials present a suffocation hazard. Children often underestimate
danger. Always keep the product out of reach
of children.
We assume no liability for material damage or
personal injury due to improper handling or
failure to comply with the safety instructions!
To avoid danger to life from
electric shock
Before connecting the lamp to the mains, always
check it and the mains lead / plug for any damage. Never use your lamp if you discover that
it is damaged in any way.
CAUTION! A damaged mains
lead presents a serious danger to
life from electric shock. The external
flexi-cable cannot be replaced, if the cable is
damaged then the lamp must be disposed of.
Never let the lamp come into contact with
water or other liquids.
Do not install the lamp on damp if conductive
surfaces.
Never open any electrical devices such as
switches, fittings etc. or allow any object to be
inserted into them. This sort of interference can
lead to a serious danger to life from electric
shock.
Touch only the insulated part of the plug when
connecting to or disconnecting from the mains
supply.
Before installation ensure that the available
mains voltag e agrees with the operating voltage required for the lamp (220–240 V ∼).
To avoid danger of fire
and injury
DANGER OF BURNS! Ensure the lamp has
been switched off and allowed to cool before
you touch it. In this way you will avoid the danger of burns. Light bulbs develop a great deal
of heat.
Replace defective bulbs immediately. Before re-
placing the bulb, always remove the mains
plug from the mains socket.
Allow the lamp to cool for at least 15 minutes
before replacing a defective bulb.
Do not allow any objects to cover the lamp.
Fire can result from the development of too
much heat.
Position the lamp so that it is protected from
moisture and dirt.
Never leave the light unattended whilst in oper-
ation. Excessive heat can result in a fire.
Only use the light bulb indicated.
Do not look directly into the light source (light
bulb, LED etc.).
This lamp is not suitable for use as a night light.
6 GB/IE
Page 7
... / Operation / Cleaning and maintenance / Disposal / Warranty and Service
Before Initial Use
Remove the threaded ring 6 from the socket 2
by turning it counter-clockwise (Fig. B).
Remove the lamp shade 1 and turn by 180°
(Fig. B).
Pull the lamp shade 1 over the socket 2
(Fig. C).
Tighten the threaded ring 6 onto the socket 2,
turning it clockwise (Fig. C).
Screw the light bulb 7 clockwise into the
socket (Fig. C).
Your light is now ready to use.
Operation
Using the lamp
Unwind the mains cable 4 completely before
use.
Insert the mains plug 5 into the socket.
Turn the light on and off with the ON / OFF
3
switch
.
Replacing a bulb
Do not use solvents such as petrol and the like
as they could damage the lamp.
For electrical safety reasons, never clean the
lamp with water or other fluids or immerse it in
water.
Use a dry, fluff-free cloth for cleaning.
The lamp is maintenance-free.
Disposal
The packaging consists entirely of environmentally friendly materials. They can
be disposed of at your local recycling
facility.
The symbol of the wheelie bin with a
cross through It means that, in the
European Union, the product has to be
disposed of in a separate refuse collection. This applies to the product and to all components bearing
this symbol. Products marked in this way may not
be disposed of with normal domestic waste but
have to be handed in at a recycling collection point
for electrical and electronic appliances. Recycling
helps to reduce the consumption of raw materials
and to ease the burden on the environment.
CAUTION! DANGER TO LIFE FROM
ELECTRIC SHOCK! Pull the mains plug
the socket.
Turn the defective light bulb 7 anti-clockwise
out of the bulb socket.
Use a clean, fluff-free cloth when you are re-
placing a bulb.
Screw the new light bulb 7 clockwise into the
socket (Fig. E).
5
out of
Cleaning and maintenance
CAUTION! DANGER TO LIFE FROM
ELECTRIC SHOCK! Before cleaning, always pull
out the mains plug
5
out of the socket.
Warranty and Service
Warranty Declaration
This product has a 3-year warranty from the date of
purchase; the warranty is only valid for the original
purchaser and is not transferable. Please keep your
receipt as proof of purchase. The warranty applies
to material or manufacturing defects only. It does not
cover wear parts or damage caused by improper
use. The guarantee lapses in cases of unauthorized
tampering. Your statutory rights are not restricted in
any way by this warranty. Please contact the service
centre by telephone. In the event of any claims under
the warranty. This is the only way to ensure that your
instrument can be returned free of charge.
7 GB/IE
Page 8
Warranty and Service
Service address
Briloner Leuchten GmbH
Im Kissen 2, 59929 Brilon, Germany
Phone: +49 (0) 29 61 / 97 12–0
Fax: +49 (0) 29 61 / 97 12–199
E-mail: Info@briloner.de
www.briloner.de
IAN 93365
Please have your receipt and the product number
(e.g. IAN 12345) available for all queries as proof
of purchase.
Declaration of conformity
This product fulfils the requirements of the applicable
European and national directives (Electromagnetic
Compatibility 2004 / 108 / EC, Low Voltage Directive
2006 / 95 / EC, Ecodesign Directive 2009 / 125 / EC,
RoHS Directive 2011/ 65 / EU). Conformity has
been demonstrated. The relevant declarations and
documents are held by the manufacturer.
Manufacturer
Briloner Leuchten GmbH
Im Kissen 2
59929 Brilon
Germany
8 GB/IE
Page 9
BRILONER LEUCHTEN GMBH
Im Kissen 2
59929 Brilon (Germany)
Last Information Update: 12 / 2013 · Ident.-No.:
7424-018L-BS / 7425-018L-BS / 7430-018L-BS-122013-6
IAN 93365
Loading...