KDC-C712
KDC-C662
KDC-C462
COMPACT DISC AUTO CHANGER
INSTRUCTION MANUAL
© B64-1381-00 (EF)
Safety precautions
2WARNING
Take the following precautions to prevent fire and avoid personal injury :
•Check that no metal objects (coins, tools, etc.) are left inside the unit to avoid short circuits.
•If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer.
2CAUTION
Take the following precautions to keep the unit in proper working order.
•Do not open the top or bottom cover.
•Do not install the unit in places it is exposed to direct sunlight, high heat or humidity, water may splash over it, or dust exists.
•Do not install the unit at a dusty place. If the unit is installed at a dusty place, dust accumulates inside the unit and unit may be damaged.
•When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. on the other side.
•If the unit is installed near speakers, the speakers vibration may causes a sound skip. Install the unit as far away as possible from the speakers.
NOTE
•If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer.
•If it doesn't seem to be working properly, first press the Reset button. If the malfunction persists, consult your Kenwood dealer.
IMPORTANT INFORMATION
•This unit is NOT designed to be connected directly to control units that are manufactured and sold before 1994. If used with such units, an optional CA-SD200 (sold separately) must be used.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT AND CONTROL UNIT.
<KDC-C712/C622>
•The disc name preset function can register names of up to 100 discs using up to 12 characters for each disc name.
The availability of this function as well as the number of discs which can be registered using this function and the number of usable characters may be variable depending on the control unit in use.
<KDC-C462>
•The disc name preset feature can store the names of up to 50 discs in memory. This feature may sometimes unable to be controlled from the control unit.
Do Not Use Special Shape CDs
•Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.
•Be sure to use CDs with disc mark 
only for this unit.
Do Not Use CDs with Sticker on the Labeled Side
•Do not use the CD with the label sticker stuck on it.
Using such a CD may cause the CD to be deformed and the sticker to peel off, resulting in malfunction of the unit.
Cleaning the unit
•If the front panel is dirty, wipe it clean with a silicon cloth or soft dry cloth with the power off.
2CAUTION
Do not use hard cloths or paint thinner, alcohol, or other volatile solvents. These may damage external surfaces or remove indicator characters.
Lens fogging
•In cold climates, there may be a period after you turn on your vehicle's heater when the lens that guides the laser beam used in your CD player fogs up. If this happens, you cannot play compact discs. Take out discs and the fogging will disappear. If it does not return to normal after several hours, contact your Kenwood dealer.
Heat protection
•In warm climates, when vehicles are left standing in direct sunlight with the windows closed, the temperature inside can rise above 60°C. The unit's protection circuits will then display the message "HOLD" and prevent the player from operating. Just open the windows or turn on the air conditioning. As soon as the "HOLD" message disappears, the player will operate normally.
2
Handling compact discs
Stains, scratches, or warping can cause skipping, malfunction, or low sound quality. Take the following precautions to avoid damage to the compact discs.
•Avoid touching the recorded side (the side without the titles on) when you hold a compact disc.
•Do not stick paper tape, etc. on either stick of the disc.
•Do not store discs where they will be exposed to direct sunlight (such as on the seat and dashboard) or high heat.
•If you do not use your unit for an extended time, remove the discs from the unit and put them in their cases. Do not leave them lying around without cases, piled up, or leaning on a wall and so on.
•If you attach an adapter to an 8 cm (3") compact disc and load it into this unit, the adapter may be detached from the disc, causing damage to the unit. Do not use 8 cm (3") compact discs.
Warning
The marking of products using lasers (Except for some areas)
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is using laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.
3
Loading...