JLG 2505 Operator Manual

Operation & Safety

An Oshkosh Corporation Company

Manual

Original Instructions

Keep this manual with machine at all times.

Models

G5-18A

2505

31200359

Revised

November 11, 2011

CALIFORNIA PROPOSITION 65

BATTERY WARNING

Battery posts,

terminals and related

accessories contain

lead and lead compounds,

chemical known to the

State of California

to cause cancer and

reproductive harm.

WASH HANDS

AFTER HANDLING!

CALIFORNIA PROPOSITION 65

EXHAUST WARNING

Diesel Engine exhaust and

some of its constituents

are known to the State of

California to cause cancer,

birth defects and other

reproductive harm.

Revision Log

February 20, 2008 - A - Original Issue of Manual April 29, 2008 - B - Revised manual. August 4, 2009 - C - Revised pages b, c, d, 1-2 thru 1-6, 1-9, 2-1, 2-4 thru 2-7, 2-10,

3-2 thru 3-5, 3-7, 3-8, 3- 9, 3 -11, 3-12 , 3-13 , 4-1, 4-2, 4- 4 t hru 4-9, 4-11, 5-1 , 5-2 , 5-4, 5-6, 5-7, 5-9 thru 5-12, 5-16, 5-18 thru 5-27, 6-1, 7-2, 7-4, 7-5, 7-8, 7-13 & 9-2 thru 9-5.

November 16, 2009 - D - Revised cover. November 11, 2011 - E - Revised pages 2-5, 2-7, 2-8, 2-9, 3-8 thru 3-11, 7-4, 8-1 &

9-3.

REVISION LOG

a31200359

Read This First

This manual is a very important tool! Keep it with the machine at all times. The purpose of this manual is to provide owners, users, operators, lessors, and

lessees with the precautions and operating procedures essential fo r the safe and proper machine operation for its intended purpose.

Due to continuous product improvements, JLG Industries, Inc. reserves the right to make specification changes without prior notification. Contact JLG Indu stries, Inc. for updated information.

Operator Qualifications

The operator of the machine must not operate the machine until this manual has been read, training is accomplished and operation of the machine has been completed under the supervision of an experienced and qualified operator. Operation within the U.S.A. requires training per OSHA 1910.178.

Operators of this equipment must possess a valid, applicable driver ’s license, be in good physical and mental condition, have normal reflexes and reaction time, good vision and depth perception and normal hearing. Operator must not be using medication which could impair abilities nor be under the influence of alcohol or any other intoxicant during the work shift.

In addition, the operator must read, understand and comply with instructions contained in the following material furnished with the telehandler:

• This Operation and Safety Manual

• Telehandler Safety Manual (ANSI only)

• All instructional decals and plates

• Any optional equipment instructions furnished

The operator must also read, understand and comply with all applicable Employer, Industry and Governmental rules, standards and regulations.

Modifications

Any modification to this machine must be approved by JLG.

b 31200359

Read This First

This product must comply with all safety related bulletins. Contact JLG Industries, Inc. or the local authorized JLG representative for information regarding safetyrelated bulletins which may have been issued for this product.

JLG Industries, Inc. sends safety related bulletins to the owner of record of this machine. Contact JLG Industries, Inc. to ensure that the current owner records are updated and accurate.

JLG Industries, Inc. must be notified immediately in all instances where JLG products have been involved in an accident involving bodily injury or death of personnel or when damage has occurred to personal property or the JLG product.

FOR:

• Accident Reporting and Product Safety Publications

• Current Owner Updates

• Questions Regarding Product Applications and Safety

• Standards and Regulations Compliance Information

• Questions Regarding Product Modifications

CONTACT:

Product Safety and Reliability Department JLG Industries, Inc. 13224 Fountainhead Plaza Hagerstown, MD 21742 USA

In USA:

Toll Free: 1-877-JLG-SAFE (1-877-554-7233)

Outside USA:

Phone: +1-717-485-6591

E-mail:

ProductSafety@JLG.com

c31200359

Read This First

Other Publications Available

Service Manual............................................................... .. ... ......................31200361

Illustrated Parts Manual.............................................................................31200360

Note: The following standards may be referenced in this manual: ANSI is compliant to ANSI/ITSDF B56.6 AUS is compliant to AS 1418.19 CE is compliant to EN1459 Refer to the machine Serial Number Plate to identify the applicable compliance standard.

d 31200359

T a bl e of Conte nts

TABLE OF CONTENTS

Revision Log Read This First

Operator Qualifications ......................................................b

Modifications......................................................................b

Other Publications Available ..............................................d

Table of Contents Section 1 - General Safety Practices

1.1 Hazard Classification System ..............................................1-1

Safety Alert System and Safety Signal Words................1-1

1.2 General Precautions ............................................................1-1

1.3 Operation Safety..................................................................1-2

Electrical Hazards...........................................................1-2

Tip Over Hazard..............................................................1-3

Travel Hazard .................................................................1-6

Load Falling Hazard........................................................1-7

Lifting Personnel .............................................................1-8

Driving Hazards On Slopes................................ ... ... .... ...1- 9

Pinch Points and Crush Hazards ..................................1-10

Fall Hazard....................................................................1-12

Chemical Hazards.........................................................1-13

Table of Contents

Section 2 - Pre-Operation and Inspection

2.1 Pre-Operation Check and Inspection...................................2-1

2.2 Safety Decals................................ ... .... ................................2-4

ASME (G5-18A, if equipped) .......... ... ... ... ... ....................2-4

ISO (2505) (G5-18A, if equipped)...................................2-6

2.3 Walk-Around Inspection.......................................................2-8

2.4 Warm-Up and Operational Checks....................................2-10

Warm-Up Check ...........................................................2-10

Operational Check ............................................. ... ... .... .2-1 0

2.5 Operator Cab.....................................................................2-11

2.6 Windows ............................................................................2-12

Cab Door Window (if equipped)....................................2-12

Rear Window ........................ ... .....................................2-1 3

Section 3 - Controls and Indicators

3.1 General................................................................................3-1

3.2 Controls ...............................................................................3-2

Park Brake ......................................................................3-4

Parking Procedure ..........................................................3-5

Ignition ............................................................................3-6

i31200359

Table of Contents

Transmission Control Lever............................................ 3-7

Load Stability Indicator - LSI (2505)............................... 3-8

LSI Override Switch (2505) ............................ ... .... ... ... . 3-11

Instrument Panel .......................................................... 3-12

Steering Column Adjuster (if equipped)........................3-13

Joystick......................................................................... 3-14

Right Hand Console ..................................................... 3-16

Accessory Control Lever (if equipped) ......................... 3-18

3.3 Steer Modes..................................................................... . 3-19

Steer Mode Change .................................... ................. 3-19

3.4 Operator Seat.................................................................... 3-20

Adjustments..................................................................3-20

Seat Belt....................................................................... 3-21

3.5 Boom Angle and Extension Indicators .............................. 3-22

Section 4 - Operation

4.1 Engine................................................................................. 4-1

Starting the Engine......................................................... 4-1

Battery Boosted Starting................................................. 4-2

Normal Engine Operation............................................... 4-3

Shut-Down Procedure ....................................................4-3

4.2 Operating with a Non-Suspended Load.............................. 4-4

Lift Load Safely............................ ... ... .... ......................... 4-4

Before Picking Up a Load............................................... 4-4

Transporting a Load .................................... ... ................ 4-5

Leveling Procedure......................................................... 4-5

Placing a Load................................................................ 4-6

Disengaging a Load........................................................ 4-6

4.3 Operating with a Suspended Load (ANSI & CE).................4-7

Lift Load Safely............................ ... ... .... ......................... 4-7

Picking Up a Suspended Load ....................................... 4-7

Transporting a Suspended Load .................................... 4-8

Leveling Procedure......................................................... 4-8

Placing a Suspended Load............. ... .... ... ...................... 4-9

Disengaging a Suspended Load .................................... 4-9

4.4 Road Operation (2505). .... ... ....................................... ....... 4-10

4.5 Loading and Securing for Transport.................................. 4-11

Tiedown........................................................................ 4-11

Lifting............................................................................4-12

ii 31200359

Section 5 - Attachments and Hitches

5.1 Approved Attachments ........................................................5-1

5.2 Unapproved Attachments ....................................................5-1

5.3 JLG Supplied Attachments ..................................................5-2

5.4 Telehandler/Attachment/Fork Capacity................................5-4

5.5 Use of the Capacity Chart....................... ... ... ... ....................5-5

Capacity Indicator Locations................................. ... .... ...5-5

Sample Capacity Chart (ANSI & CE)..............................5-6

Sample Capacity Chart (AUS) ........................................5-7

Example..........................................................................5-8

5.6 Attachment Installation ........................................................5-9

Standard Quick Attach.................... ................................5-9

Universal Quick Attach (UQC) ......................................5-12

5.7 Hydraulic Operated Attachment....... .... ... ... ... ... ..................5-14

5.8 Adjusting/Moving Forks......................................................5-15

5.9 Attachment Operation........................................................5-16

Carriage w/Forks...........................................................5-18

Fork Mounted Hook (ANSI & CE) .................................5-19

Side Tilt Carriage ..........................................................5-20

Side Shift Carriage........................................................5-22

Bucket...........................................................................5-24

Grapple Bucket .............................................................5-26

5.10 Hitches...............................................................................5-28

Pin Hitch........................................................................5-28

Adjustable Pin Hitch......................................................5-29

Adjustable Auto Hitch....................................................5-30

Table of Contents

Section 6 - Emergency Procedures

6.1 Towing a Disabled Product..................................................6-1

Moving Short Distances..................................................6-1

Moving Longer Distances ...............................................6-1

6.2 Emergency Lowering of Boom.............................................6-2

6.3 Emergency Exit from Enclosed Cab....................................6-2

Section 7 - Lubrication and Maintenance

7.1 Introduction..........................................................................7-1

Clothing and Safety Gear................................ ... .............7-1

7.2 General Maintenance Instructions.......................................7-2

7.3 Service and Maintenance Schedule ....................................7-3

10 & 1st 50 & 50 Hour Maintenance Schedule........ .... ...7- 3

1st 250, 250 & 500 Hour Maintenance Schedule ...........7-4

1000 Hour Maintenance Schedule..................................7-5

iii31200359

Table of Contents

7.4 Lubrication Schedules......................................................... 7-6

250 Hour Lubrication Schedule ...................................... 7-6

7.5 Operator Maintenance Instructions..................................... 7-8

Fuel System....................... ... .... ...................................... 7-8

Engine Oil..................................................................... 7-10

Hydraulic Oil............ .... ... ... ....................................... ... . 7-11

Tires.............................................................................. 7-12

Air Intake System ......................................................... 7-14

Engine Cooling System ................................................ 7-16

Battery.......................................................................... 7-17

Brake System....... ... .... ... ... ... ....................................... . 7-18

Windshield Washer System (if equipped)..................... 7-19

Section 8 - Additional Checks

8.1 General................................................................................ 8-1

8.2 Load Stability Indicator System (2505)................................ 8-1

Section 9 - Specifications

9.1 Product Specifications......... ... ....................................... ... ... 9-1

Fluid and Lubrication Capacities .................... ... .... ... ... ... 9-1

Tires................................................................................ 9-2

Performance................................................................... 9-3

Dimensions..................................................................... 9-4

Declaration of Vibration (CE).......................................... 9-5

Noise Emission Level (CE)............................................. 9-5

Index Inspection, Maintenance and Repair Log

iv 31200359

Section 1 - General Safety Practices

DANGER

OW0010

WARNING

OW0021

CAUTION

OW0031

SECTION 1 - GENERAL SAFETY PRACTICES

1.1 HAZARD CLASSIFICATION SYSTEM Safety Alert System and Safety Signal Words

DANGER indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a potentially h azardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentiality hazardous situation which, if not avoided, may result in minor or moderate injury.

1.2 GENERAL PRECAUTIONS

WARNING

Before operation, read and understand this manual. Failure to comply with the safety precautions listed in this manual could result in machine damage, property damage, personal injury or death.

1-131200359

Section 1 - General Safety Practices

OW0040

10 FT

(3 M)

1.3 OPERATION SAFETY Electrical Hazards

• This machine is not insulated and does not provide protection from contact or being near electrical current.

• NEVER operate the telehandler in an area where overhead power lines, overhead or underground cables, or other power sources may exist without ensuring the appropriate power or utility company de-energizes the lines.

• Always check for power lines before raising the boom.

• Follow employer, local and governmental regulations for clearance from powerlines.

1-2 31200359

Section 1 - General Safety Practices

OW0050

OW0080

OW0100

4 FT

(1,2 M)

Tip Over Hazard

General

• For additional load requirements, refer to the appropriate capacity chart.

• Never use an attachment without the appropriate JLG appro ved capacity chart installed on the telehandler.

• Understand how to properly use the capacity charts located in cab.

• DO NOT exceed rated lift capacity.

• Be sure that the ground conditions are able to support the machine.

• DO NOT raise boom unless frame is level (0 degrees), unless otherwise noted on capacity chart.

• DO NOT level machine with boom/attachment above 4 ft (1,2 m). (AUS - DO NOT level machine with load more than 300 mm (11.8 in) above ground surface.)

1-331200359

Section 1 - General Safety Practices

OH2291

OH20911

OH2221

• MAINTAIN proper tire pressure at all times. If proper tire pressures are not maintained, this machine could tip over.

• Refer to manufacturer’s specifications for proper fill ratio and pressure requirements for tires equipped with ballast.

• Always wear the seat belt.

• Keep head, arms, hands, legs and all other body parts inside operator’s cab at all times.

If the telehandler starts to tip over:

• DO NOT JUMP

• BRACE YOURSELF and STAY WITH THE MACHINE

• KEEP YOUR SEAT BELT FASTENED

• HOLD ON FIRMLY

• LEAN AWAY FROM THE POINT OF IMPACT

1-4 31200359

Non-Suspended Load

OW0060

OW0150

• DO NOT drive with boom raised.

Suspended Load

Section 1 - General Safety Practices

• Tether suspended loads to restrict movement.

• Weight of all rigging (slings, etc.) must be included as part of load.

• Beware of wind. Wind can cause a suspended load to swing and cause dangerous side loads - even with tag lines.

• DO NOT attempt to use telehandler frame-leveling to compensate for load swing.

• Keep heavy part of load closest to attachment.

• Never drag the load; lift vertically. When driving with a suspended load:

• Start, travel, turn and stop slowly to prevent load from swinging.

• DO NOT extend boom.

• DO NOT raise the load more than 11.8 in (300 mm) above ground surface or the boom more than 45°.

• DO NOT exceed walking speed.

1-531200359

Section 1 - General Safety Practices

OAL2030

2-Wheel Front Steer 4-Wheel Circle Steer 4-Wheel Crab Steer

Travel Ha zard

• Steering characteristics differ between steer modes. Identify the steer mode settings of the telehandler being operated.

• DO NOT change steer modes while traveling. Steer modes must be changed while telehandler is stationary.

• Visually verify proper wheel alignment after each steer mode change.

• Ensure that adequate clearance is provided for both rear tail swing and front fork swing.

• Look out for and avoid other personnel, machinery and vehicles in the area. Use a spotter if you DO NOT have a clear view.

• Before moving be sure of a clear path and sound horn.

• When driving, retract boom and keep boom/attachment as low as possible while maintaining visibility of mirrors and maximum visibility of path of travel.

• Always look in the direction of travel.

• Always check boom clearances carefully before driving underneath overhead obstructions. Position attachment/load to clear obstacles.

• When driving in high speed, use only front wheel steer (if steering modes are selectable).

1-6 31200359

Section 1 - General Safety Practices

OW0130

Load Falling Hazard

• Never suspend load from forks or other parts of carriage.

• DO NOT burn or drill holes in fork(s).

• Forks must be centered under load and spaced apart as far as possible.

1-731200359

Section 1 - General Safety Practices

OW0170

OW0190

Lifting Personnel

• When lifting personnel, USE ONLY a JLG approved personnel work platform, with proper capacity chart displayed in the cab.

• DO NOT drive machine from cab when personnel are in platform.

1-8 31200359

Section 1 - General Safety Practices

OW0200

Driving Hazards On Slopes

To maintain sufficient traction and braking capabilities, travel on slopes as follows:

• When unloaded, the rear of the machine is the “heavy end.” Drive with forks pointed downhill.

• When loaded, the front of the machine is the “heavy end.” Drive with the forks pointed uphill.

• For additional travel requirements, refer to the appropriate capacity chart.

• To avoid overspeeding the engine and drivetrain when driving down slopes, downshift to a lower gear and use the service brake as necessary to maintain a slow speed. DO NOT shift into neutral and coast downhill.

• Avoid excessively steep slopes or unstable surfaces. To avoid tip over DO NOT drive across excessively steep slopes under any circumstances.

• Avoid turning on a slope. Never engage “inching” or shift to “Neutral” when going downhill.

• DO NOT park on a slope.

1-931200359

Section 1 - General Safety Practices

OW0210

OW0220

OW0230

Pinch Points and Crush Hazards

Stay clear of pinch points and rotating parts on the telehandler.

• Stay clear of moving parts while engine is running.

• Keep clear of steering tires and frame or other objects.

• Keep clear from under boom.

1-10 31200359

Section 1 - General Safety Practices

OW0240

OW0250

OW0260

OW0960

• Keep clear of boom holes.

• Keep arms and hands clear of attachment tilt cylinder.

• Keep hands and fingers clear of carriage and forks.

• Keep others away while operating.

1-1131200359

Section 1 - General Safety Practices

OW0280

OW0290

Fall Hazard

• Enter using the proper hand holds and steps provided. Always maintain 3-point contact when mounting or dismounting. Never grab control levers or steering wheel when mounting or dismounting the machine.

• DO NOT get off the machine until the shutdown procedure on page 4-3 has been performed.

• DO NOT carry riders. Riders could fall off machine causing death or serious injury.

1-12 31200359

Section 1 - General Safety Practices

OW0300

OW0950

Chemical Hazards

Exhaust Fumes

• DO NOT operate machine in an enclosed area without proper ventilation.

• DO NOT operate the machine in hazardous environments unless approved for that purpose by JLG and site owner. Sparks from the electrical system and the engine exhaust can cause an explosion.

• If spark arrestors are required, ensure they are in place and in good working order.

Flammable Fuel

• DO NOT fill the fuel tank or service the fuel system near an open flame, sparks or smoking materials. Engine fuel is flammable and can cause a fire and/or explosion.

Hydraulic Fluid

• DO NOT attempt to repair or tighten any hydraulic hoses or fittings while the engine is running or when the hydraulic system is under pressure.

• Stop engine and relieve trapped pressure. Fluid in the hydraulic system is unde r enough pressure that it can penetrate the skin.

• DO NOT use your hand to check for leaks. Use a piece of cardboard or paper to search for leaks. Wear gloves to protect hands from spraying fluid.

1-1331200359

Section 1 - General Safety Practices

This Page Intentionally Left Blank

1-14 31200359

Section 2 - Pre-Operation and Inspection

OAH1000

PARENT METAL CRACK WELD CRACK

SECTION 2 - PRE-OPERATION AND INSPECTION

2.1 PRE-OPERATION CHECK AND INSPECTION

Note: Complete all required maintenance before operating unit.

WARNING

FALL HAZARD. Use extreme caution when checking items beyond your normal

reach. Use an approved ladder.

The pre-operation check & inspection, performed at beginning of each work sh ift or at each change of operator, should include the following:

1. Cleanliness - Check all surfaces for leakage (oil, fuel or battery fluid) or foreign objects. Report any leakage to the proper maintenance personnel .

2. Structure - Inspect the machine structure for dents, damage, weld or parent metal cracks or other discrepancies.

3. Safety Decals - Ensure all safety decals are legible and in place. Clean or replace as required. See page 2-4 for details.

4. Operation and Safety Manuals - Operation & Safety Manual and AEM Safety Manual (ANSI only) are located in cab manual holder.

5. Walk-Around Inspection - See page 2-8 for details.

6. Fluid Levels - Check fluids, including fuel, brake fluid, hydraulic oil, engine oil and coolant. When adding fluids, refer to Section 7 - Lubrication and Maintenance and Section 9 - Specifications to determine proper type and intervals. Before removing filler caps or fill plugs, wipe all dirt and grease away from the ports. If dirt enters these ports, it can severely reduce component life.

7. Attachments/Accessories - Ensure correct capacity charts are installed on the telehandler. If provided, reference the Operation & Safety Manual of each attachment or accessory installed for specific inspection, operation and maintenance instructions.

2-131200359

Section 2 - Pre-Operation and Inspection

8. Operational Check - Once the walk-around inspection is complete, perform a warm-up and operational check (see page 2-10) of all systems in an area free of overhead and ground level obstructions. See Section 3 - Controls and Indicators for more specific operating instructions.

WARNING

If telehandler does not operate properly, immediately bring machine to a stop, lower boom and attachment to ground and stop the engine. Determine cause and correct before continued use.

2-2 31200359

Section 2 - Pre-Operation and Inspection

This Page Intentionally Left Blank

2-331200359

Section 2 - Pre-Operation and Inspection

OAH2070

8005870C

8005870

1701500

1706300

1706300C

1706302

1706298A

1706298

1702300

1706301A

1706301

1701500

1706302

4100181

1705881

(S/N 0160037069

THRU 0160037437)

1001081395

(S/N 0160037456

& AFTER)

Model

SerialNumber

YearOfManufacture

MaximumWeightWithout Attachments(lbs/kg)

MaximumCapacity(lbs/kg)

°Referto load capacity chart for truck with attachment, and individual load ratings stamped onforks,if equipped. Use lowest capacity of all ratings. Asreleasedfrom factory this truck meets specifications in ASME B56.6-2002 Part III.

1001100586A

Manufacturedby JLG under license from

Manufacturedby JLGIndustriesInc. McConnellsburg,PA 17233-9533 USA

Oneormore of the following patents may apply to this truck: U.S. Nos. 4,954,041 6,349,969 5,639,1195,813,697 5,230,399 5,052,532. Otherpatents pending.

91563220

91563220 REV A

2.2 SAFETY DECALS

Ensure all DANGER, WARNING, CAUTION and instructional decals and proper capacity charts are legible and in place. Clean and replace as required.

ASME (G5-18A, if equipped)

2-4 31200359

OAH1052

1706299A

CONTACTING

POWERLINES

willresult in death

orserious injury.

1706299

1706850A

CRUSHING HAZARD

Keepothers

awaywhile operating.

Loweringboom or falling load could

causedeath or serious injury.

WARNING

1706850

1001101071B

1001101071

Fasten

seat belt.

1706303A

Operatormust be trained and

mustread and understand

allcapacity charts, operator

andsafety manuals.

1706303

1706306A

1706306

1706851A

1706851

1706767A

1706767

1706304A

RUN-OVER

HAZARD

couldcause

deathor

serious

injury.

1706304

Axle Trunnions

Axle Kingpins (Both Axles)

Boom Pivot

Tilt Cylinder & Carriage Pivot

1001100107

1001099710

250

XXXXX

XXX

B C D E

1001099783

-10

4105262

Model

SerialNumber

YearOfManufacture

MaximumWeightWithout Attachments(lbs/kg)

MaximumCapacity(lbs/kg)

1001100586A

Manufacturedby JLG under license from

Manufacturedby JLGIndustriesInc. McConnellsburg,PA 17233-9533 USA

Oneormore of the following patents may apply to this truck: U.S. Nos. 4,954,041 6,349,969 5,639,1195,813,697 5,230,399 5,052,532. Otherpatents pending.

1705881

(BEFORE

S/N 0160037069)

1702300

1701500

1706302

1706768

1706296

1001097475

F11

10 A

F12

10 A

F13

15 A

F14

10 A

F15

10 A

F16

10 A

R01

35 A

R02

35 A

15 A

5 A

10 A

7.5 A

15 A

10 A F9 F10

1001097475A

15 A

VIEW A-A

VIEW OF BATTERY COVER

CAPACITY CHARTS

Section 2 - Pre-Operation and Inspection

2-531200359

Section 2 - Pre-Operation and Inspection

OAH2080

1702300

1701500

1706292

1706282

1706098B

1706098

1702300

1701500

Model

ManufacturedbyJLG under license from

Date OfManufacture:

Product Identification Number

Serial Number

Type of engine:

Output of engine, kW:

Gross vehicle weight:

Maximum capacity:

Maximum capacity at max height:

1001098486A

MANUFACTURED BY

JLG Industries 1 JLG Drive McConnellsburg, PA 17233

USA

2505 CE - 1001098487

(S/N 0160037067 & AFTER)

2505 AUS - 1001107655

G5-18A - 1705881

(S/N 0160037069 THRU 0160037437)

G5-18A - 1001081395

(S/N 0160037456 & AFTER)

8005671

8005670

1706285

3700016

4100181

91563220

91563220 REV A

20 - 2603207

30 - 1001081158

(GERMANY)

1706292

3700016

3931579

20 - 2603207

30 - 1001081158

(GERMANY)

8005870C

8005870

ISO (2505) (G5-18A, if equipped)

2-6 31200359

+ 112 hidden pages