FM/MW/LW
CD Car Audio
FM/MW/LW
CD Автомобильное Аудио
To cancel the demonstration (DEMO) display, see page 12.
For the connection/installation, see page 22.
Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte auf Seite 13 nach.
Informationen zum Anschluss und zur Installation finden Sie auf Seite 25.
Pour annuler la démonstration (DEMO), reportezvous à la page 13.
Pour le raccordement/l’installation, reportez-vous à la page 24.
Per annullare la dimostrazione (DEMO), vedere pagina 13.
Per l’installazione e i collegamenti, consultare pagina 24.
Para cancelar la pantalla de demostración (DEMO), consulte la página 13.
Para la conexión/instalación, consulte la página 24.
Для отмены демонстрации на дисплее (режим DEMO) см. стр. 13.
Инструкции по установке/подключению см. на стр. 26.
4-739-353-11(1)
Operating Instructions |
GB |
|
|
|
|
Bedienungsanleitung |
DE |
|
|
|
|
Mode d’emploi |
FR |
|
|
|
|
Istruzioni per l’uso |
IT |
|
|
|
|
Manual de |
ES |
instrucciones |
|
|
|
|
|
Инструкция по |
RU |
эксплуатации |
|
|
|
|
|
CDX-G3300UV
For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use.
For details, see “Connection/Installation” (page 22).
Made in Thailand
This product is classified as a Class 1 Laser product under IEC/EN 60825-1:2007 and IEC/ EN 60825-1:2014.
Emission Duration: Continuous
Laser Output: Less than 55.8 μW
Wavelength: 775 nm to 800 nm
The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.
The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area).
Hereby, Sony Corporation declares that this equipment is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://www.compliance.sony.de/
This equipment is intended to be used with the approved version(s) of software that are indicated in the EU Declaration of Conformity.
The software loaded on this equipment is verified to comply with the essential requirements of the Directive 2014/53/EU. The software version can be checked in the firmware setup item of the general setup menu.
Notice for customers: the following information is only applicable to equipment sold in countries applying EU Directives
This product has been manufactured by or on behalf of Sony Corporation.
EU Importer: Sony Europe Limited. Inquiries to the EU Importer or related to product compliance in Europe should be
sent to the manufacturer’s authorized representative, Sony Belgium, bijkantoor van Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem, Belgium.
Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other countries with
separate collection systems)
This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbol for lead (Pb) is added if the battery contains more than 0.004% lead. By ensuring that these products and batteries are disposed of correctly, you will help to prevent potentially negative consequences for the environment and human health which could be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end- of-life to the appropriate collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the appropriate collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery.
CAUTION
The following frequency 65 – 74 MHz range is not allocated to sound broadcasting in the European Common Allocations table and cannot be used in Europe.
2GB
Warning if your car’s ignition has no ACC position
Be sure to set the AUTO OFF function (page 12). The unit will shut off completely and automatically in the set time after the unit is turned off and the clock is displayed (i.e. press and hold OFF for 1 second), which prevents battery drain. If you do not set the AUTO OFF function, press and hold OFF until the display disappears each time you turn the ignition off.
Disclaimer regarding services offered by third parties
Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.
3GB
Table of Contents
Guide to Parts and Controls. . . . . . . . . . . . . 5
Getting Started
Detaching the Front Panel . . . . . . . . . . . . . . 7
Resetting the Unit. . . . . . . . . . . . . . . . . . . . . 7
Setting the Clock. . . . . . . . . . . . . . . . . . . . . . 7
Checking the Battery Voltage . . . . . . . . . . . 8
Connecting a USB Device. . . . . . . . . . . . . . . 8
Connecting Other
Portable Audio Device . . . . . . . . . . . . . . 8
Listening to the Radio
Listening to the Radio . . . . . . . . . . . . . . . . . 9 Using Radio Data System (RDS). . . . . . . . . . 9
Playback
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . 10
Playing a USB Device . . . . . . . . . . . . . . . . . 10
Searching and Playing Tracks . . . . . . . . . . . 11
Settings
Canceling the DEMO Mode . . . . . . . . . . . . 12
Basic Setting Operation . . . . . . . . . . . . . . . 12
General Setup (GENERAL) . . . . . . . . . . . . . 12
Sound Setup (SOUND) . . . . . . . . . . . . . . . . 13
Display Setup (DISPLAY). . . . . . . . . . . . . . . 14
Additional Information
Updating the Firmware . . . . . . . . . . . . . . . 15
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting . . . . . . . . . . . . . . . . . . . . . 18
Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connection/Installation
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Parts List for Installation. . . . . . . . . . . . . . . 22 Connection . . . . . . . . . . . . . . . . . . . . . . . . . 23 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 25
4GB
Guide to Parts and Controls
Main unit
PTY (program type)
Select PTY in RDS.
(browse) (page 11)
Enter the browse mode during playback. (Not available when a USB device in Android™ mode or iPod is connected.)
Front panel release button
SRC (source)
Turn on the power. Change the source.
OFF
Press and hold for 1 second to turn the source off and display the clock.
Press and hold for more than 2 seconds to turn off the power and the display.
Control dial
Rotate to adjust the volume.
PUSH ENTER
Enter the selected item.
Press SRC, rotate then press to change the source (timeout in 2 seconds).
MENU
Open the setup menu.
Disc slot
Display windowUSB port
(disc eject)
/
(SEEK –/+)
Tune in radio stations automatically. Press and hold to tune manually.
/ (prev/next)
/ (fast-reverse/fast-forward)
(back)
Return to the previous display.
MODE (page 9)
EQ (equalizer)
Select an equalizer curve.
Receptor for the remote commander
Number buttons (1 to 6)
Receive stored radio stations. Press and hold to store stations.
ALBUM /
Skip an album for audio device. Press and hold to skip albums continuously.
(Not available when a USB device in Android mode or iPod is connected.)
(repeat)
(Not available when a USB device in Android mode is connected.)
(shuffle)
(Not available when a USB device in Android mode is connected.)
(play/pause)
5GB
EXTRA BASS
Reinforces bass sound in synchronization with the volume level. Press to change the EXTRA BASS setting: [1], [2], [OFF].
AUX input jack
DSPL (display)
Press to change display items.
SCRL (scroll)
Press and hold to scroll a display item.
6GB
Getting Started
Detaching the Front Panel
You can detach the front panel of this unit to prevent theft.
1Press and hold OFF until the unit
turns off, press the front panel release button , then pull the panel towards you to remove.
Caution alarm
If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used.
Attaching the front panel
Resetting the Unit
Before operating the unit for the first time, after replacing the car battery, or changing the connections, you must reset the unit.
1Press DSPL and EQ for more than 2 seconds.
Note
Resetting the unit will erase the clock setting and some stored contents.
Setting the area/region
After resetting the unit, the area/region setting display appears.
1Press ENTER while [SET AREA] is displayed.
The area/region currently set appears.
2Rotate the control dial to select [EUROPE] or [RUSSIA], then press it.
3Rotate the control dial to select [YES] or [NO], then press it.
If the setting area/region is changed, the unit is reset, then the clock is displayed.
This setting can be configured in the general setup menu (page 12).
Setting the Clock
1Press MENU, rotate the control dial to select [GENERAL], then press it.
2Rotate the control dial to select [SET CLOCK], then press it.
3Rotate the control dial to select [MANUAL], then press it.
The hour indication flashes.
4Rotate the control dial to set the hour and minute.
To move the digital indication, press/ (SEEK –/+).
5After setting the minute, press MENU.
The setup is complete and the clock starts.
To display the clock
Press DSPL.
To set the clock automatically
Select [AUTO <RDS>] in step 3.
7GB
Checking the Battery
Voltage
You can check the current battery voltage. (Not available while the source is off and the clock is displayed.)
1Press DSPL repeatedly until the battery voltage display appears.
Connecting a USB Device
1 Turn down the volume on the unit.
2Connect the USB device to the unit.
To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied).
Connecting Other Portable
Audio Device
1 Turn off the portable audio device.
2 Turn down the volume on the unit.
3Connect the portable audio device to the AUX input jack (stereo mini jack) on the unit with a connecting cord (not supplied)*.
* Be sure to use a straight type plug.
4 Press SRC to select [AUX].
To match the volume level of the connected device to other sources
Start playback of the portable audio device at a moderate volume, and set your usual listening volume on the unit.
Press MENU, then select [SOUND] [SET AUX VOL] (page 14).
8GB
Listening to the Radio
Listening to the Radio
To listen to the radio, press SRC to select [TUNER].
Storing automatically (BTM)
1Press MODE to change the band (FM1, FM2, FM3 or MW/LW).
2Press MENU, rotate the control dial to select [GENERAL], then press it.
3Rotate the control dial to select [SET BTM], then press it.
The unit stores stations in order of frequency on the number buttons.
Tuning
1Press MODE to change the band (FM1, FM2, FM3 or MW/LW).
2Perform tuning.
To tune manually
Press and hold / (SEEK –/+) to
locate the approximate frequency, then press / (SEEK –/+) repeatedly to fine adjust to the desired frequency.
To tune automatically
Press / (SEEK –/+).
Scanning stops when the unit receives a station.
Storing manually
1While receiving the station that you want to store, press and hold a number button (1 to 6) until [MEM] appears.
Using Radio Data System (RDS)
Setting alternative frequencies (AF) and traffic announcement (TA)
AF continuously retunes the station to the strongest signal in a network, and TA provides current traffic information or traffic programs (TP) if received.
1Press MENU, rotate the control dial to select [GENERAL], then press it.
2Rotate the control dial to select [SET AF/TA], then press it.
3Rotate the control dial to select [SET AF-ON], [SET TA-ON], [SET AF/TA-ON] or [SET AF/TA-OFF], then press it.
To store RDS stations with the AF and TA setting
You can preset RDS stations along with an AF/TA setting. Set AF/TA, then store the station with BTM or manually. If you preset manually, you can also preset non-RDS stations.
To receive emergency announcements
With AF or TA on, emergency announcements will automatically interrupt the currently selected source.
To adjust the volume level during a traffic announcement
Level will be stored into memory for subsequent traffic announcements, independently from the regular volume level.
Receiving the stored stations
1Select the band, then press a number button (1 to 6).
9GB
To stay with one regional program (REGIONAL)
When the AF and REGIONAL functions are on, you will not be switched to another regional station with a stronger frequency. If you leave this regional program’s reception area, set [SET REGIONAL] in [GENERAL] to [SET REG-OFF] during FM reception
(page 13).
This function does not work in the UK and some other areas.
Local Link function (UK only)
This function enables you to select other local stations in the area, even if they are not stored on your number buttons.
During FM reception, press a number button (1 to 6) on which a local station is stored. Within 5 seconds, press again a number button of the local station. Repeat this procedure until the local station is received.
Selecting program types (PTY)
1 Press PTY during FM reception.
2Rotate the control dial until the desired program type appears, then press it.
The unit starts to search for a station broadcasting the selected program type.
Type of programs
NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP M (Pop Music), ROCK M (Rock Music), EASY M (M.O.R. Music), LIGHT M (Light classical), CLASSICS (Serious classical), OTHER M (Other Music), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children’s program), SOCIAL (Social Affairs), RELIGION (Religion),
PHONE IN (Phone In), TRAVEL (Travel), LEISURE
(Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary)
Playback
Playing a Disc
1 Insert the disc (label side up).
Playback starts automatically.
Playing a USB Device
In these Operating Instructions, “iPod” is used as a general reference for the iPod functions on an iPod and iPhone, unless otherwise specified by the text or illustrations.
For details on the compatibility of your iPod, see “About iPod” (page 16) or visit the support site on the back cover.
AOA (Android Open Accessory) 2.0, MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices* compliant with the USB standard can be used. Depending on the USB device, the Android mode or MSC/MTP mode can be selected on the unit.
Some digital media players or Android smartphones may require setting to MTP mode.
*e.g., a USB flash drive, digital media player, Android smartphone
Notes
•For details on the compatibility of your USB device, visit the support site on the back cover.
•Smartphones with Android OS 4.1 or higher installed support Android Open Accessory 2.0 (AOA 2.0). However, some smartphones may not fully support AOA 2.0 even if Android OS 4.1 or higher is installed.
For details on the compatibility of your Android smartphone, visit the support site on the back cover.
10GB
•Playback of the following files is not supported.
MP3/WMA/FLAC:
–copyright-protected files
–DRM (Digital Rights Management) files
–Multi-channel audio files
MP3/WMA:
– lossless compression files
Before making a connection, select the USB mode (Android mode or MSC/MTP mode) depending on the USB device (page 13).
1Connect a USB device to the USB port (page 8).
Playback starts.
If a device is already connected, to start playback, press SRC to select [USB] ([IPD] appears in the display when the iPod is recognized).
2 Adjust the volume on this unit.
To stop playback
Press and hold OFF for 1 second.
To remove the device
Stop playback, then remove the device.
Caution for iPhone
When you connect an iPhone via USB, phone call volume is controlled by the iPhone, not the unit. Do not inadvertently increase the volume on the unit during a call, as a sudden loud sound may result when the call ends.
Searching and Playing
Tracks
Repeat play and shuffle play
Not available when a USB device in Android mode is connected.
1During playback, press 
(repeat) or
(shuffle) repeatedly to select the
desired play mode.
Playback in the selected play mode may take time to start.
Available play modes differ depending on the selected sound source.
Searching a track by name (QuickBrowZer™)
Not available when a USB device in Android mode or iPod is connected.
1During CD or USB playback, press 
(browse)* to display the list of search categories.
When the track list appears, press 
(back) repeatedly to display the desired search category.
* During USB playback, press 
(browse) for more than 2 seconds to directly return to the beginning of the category list.
2Rotate the control dial to select the desired search category, then press it to confirm.
3Repeat step 2 to search the desired track.
Playback starts.
To exit the Quick-BrowZer mode
Press 
(browse).
Searching by skipping items (Jump mode)
Not available when a USB device in Android mode or iPod is connected.
1During CD or USB playback, press 
(browse).
2 Press (SEEK +).
3Rotate the control dial to select the item.
The list is jumped in steps of 10% of the total number of items.
4Press ENTER to return to the QuickBrowZer mode.
The selected item appears.
5Rotate the control dial to select the desired item, then press it.
Playback starts.
11GB
Settings
Canceling the DEMO Mode
You can cancel the demonstration display which appears when the source is off and the clock is displayed.
1Press MENU, rotate the control dial to select [GENERAL], then press it.
2Rotate the control dial to select [SET DEMO], then press it.
3Rotate the control dial to select [SET DEMO-OFF], then press it.
The setting is complete.
4Press 
(back) twice.
The display returns to normal reception/ play mode.
Basic Setting Operation
You can set items in the following setup categories:
General setup (GENERAL), Sound setup (SOUND), Display setup (DISPLAY)
1 Press MENU.
2Rotate the control dial to select the setup category, then press it.
The items that can be set differ depending on the source and settings.
3Rotate the control dial to select the options, then press it.
To return to the previous display
Press 
(back).
General Setup (GENERAL)
AREA (area)
Specifies the area/region to use this unit: [EUROPE], [RUSSIA].
If the area/region currently set is changed, this unit is reset, then the clock is displayed.
(Available only while the source is off and the clock is displayed.)
DEMO (demonstration)
Activates the demonstration: [ON], [OFF].
CLOCK (clock) (page 7)
Sets the clock: [AUTO <RDS>], [MANUAL].
CAUT ALM (caution alarm)
Activates the caution alarm: [ON], [OFF] (page 7).
(Available only while the source is off and the clock is displayed.)
BEEP (beep)
Activates the beep sound: [ON], [OFF].
AUTO OFF (auto off)
Shuts off automatically after a certain time when the unit is turned off and the clock is displayed (i.e. press and hold OFF for 1 second): [ON] (30 minutes), [OFF].
STEERING (steering) Registers/resets the setting of the steering wheel remote control.
(Available only while the source is off and the clock is displayed.)
STR CONTROL (steering control)
Selects the input mode of the connected remote control. To prevent a malfunction, be sure to match the input mode with the connected remote control before use.
CUSTOM (custom)
Input mode for the steering wheel remote control
PRESET (preset)
Input mode for the wired remote control excluding the steering wheel remote control
(Automatically selected when [RESET CUSTOM] is performed.)
EDIT CUSTOM (edit custom) Registers the functions (SOURCE, ATT,
VOL +/–, SEEK +/–) to the steering wheel remote control:
Rotate the control dial to select the function you want to assign to the steering wheel remote control, then
press it.
While [REGISTER] is blinking, press and hold the button on the steering wheel remote control you want to assign the function to. When registration is complete, [REGISTERED] is displayed.
12GB
To register other functions, repeat steps and .
(Available only when [STR CONTROL] is set to [CUSTOM].)
RESET CUSTOM (reset custom) Resets the registered functions of the steering wheel remote control: [YES], [NO].
(Available only when [STR CONTROL] is set to [CUSTOM].)
Notes
•While making settings, only button operation on the unit is available. For safety, park your car before making this setting.
•If an error occurs while registering, all the previously-registered information remains. Restart registration from the function where the error occurred.
•This function may not be available on some vehicles. For details on the compatibility of your vehicle, visit the support site on the back cover.
USB MODE (USB mode)
Changes the USB mode: [ANDROID], [MSC/MTP].
(Available only when the USB source is selected.)
AF/TA (alternative frequencies/traffic announcement)
Selects the alternative frequencies (AF) and traffic announcement (TA) setting: [AF-ON], [TA-ON], [AF/TA-ON], [AF/TAOFF].
(Available when any source is selected.)
REGIONAL (regional)
Restricts reception to a specific region: [ON], [OFF].
(Available only when FM is received.)
BTM (best tuning memory) (page 9) (Available only when the tuner is selected.)
FIRMWARE (firmware)
(Available only while the source is off and the clock is displayed.)
Checks/updates the firmware version. For details, visit the support site on the back cover.
FW VERSION (firmware version) Displays current firmware version. FW UPDATE (firmware update)
Enters firmware update process: [YES], [NO].
Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.
Sound Setup (SOUND)
This setup menu is not available when the source is off and the clock is displayed.
EQ10 PRESET (EQ10 preset)
Selects an equalizer curve from 10 equalizer curves or off:
[OFF], [R&B], [ROCK], [POP], [HIP-HOP], [EDM], [JAZZ], [SOUL], [COUNTRY], [KARAOKE]*, [CUSTOM].
The equalizer curve setting can be memorized for each source.
*[KARAOKE] reduces the vocal sound but cannot fully remove it during playback. Also, using a microphone is not supported.
EQ10 CUSTOM (EQ10 custom) Sets [CUSTOM] of EQ10.
Setting the equalizer curve: [BAND1] – [BAND10] (32 Hz, 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz). The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB.
BALANCE (balance)
Adjusts the sound balance: [RIGHT-15] – [CENTER] – [LEFT-15].
FADER (fader)
Adjusts the relative level: [FRONT-15] – [CENTER] – [REAR-15].
13GB
S.WOOFER (subwoofer)
SW LEVEL (subwoofer level)
Adjusts the subwoofer volume level: [+6 dB] – [0 dB] – [-6 dB].
([ATT] is displayed at the lowest setting.) SW PHASE (subwoofer phase)
Selects the subwoofer phase: [SUB NORM], [SUB REV].
LPF FREQ (low pass filter frequency) Selects the subwoofer cut-off frequency: [80Hz], [100Hz], [120Hz].
HPF FREQ (high pass filter frequency) Selects the front/rear speaker cut-off frequency: [OFF], [80Hz], [100Hz], [120Hz].
AUX VOL (AUX volume)
Adjusts the volume level for each connected auxiliary device:
[+18 dB] – [0 dB] – [-8 dB].
This setting negates the need to adjust the volume level between sources. (Available only when the AUX is selected.)
Display Setup (DISPLAY)
DIMMER (dimmer)
Change the display brightness: [OFF], [ON], [CLK] (clock).
To set this function to be active only during a fixed period, select [CLK], then set the start and end times.
–To set the brightness when the dimmer function is activated:
Set [DIMMER] to [ON], then adjust [BRIGHTNESS].
–To set the brightness when the dimmer
function is deactivated:
Set [DIMMER] to [OFF], then adjust [BRIGHTNESS].
The brightness setting is stored and applied when the dimmer function is activated or deactivated.
BRIGHTNESS (brightness)
Adjusts the display brightness. The brightness level is adjustable: [1] – [10].
BUTTON-C (button color)
Sets a preset color or customized color for the buttons.
COLOR (color)
Selects from 15 presets colors, 1 customized color.
CUSTOM-C (custom color) Registers a customized color for the buttons.
RGB RED, RGB GRN, RGB BLUE
Adjustable color range: [0] – [32] ([0] cannot be set for all color ranges).
DSPL-C (display color)
Sets a preset color or customized color for the display.
COLOR (color)
Selects from 15 presets colors, 1 customized color.
CUSTOM-C (custom color) Registers a customized color for the display.
RGB RED, RGB GRN, RGB BLUE
Adjustable color range: [0] – [32] ([0] cannot be set for all color ranges).
SND SYNC (sound synchronization) Activates the synchronization of the illumination with the sound: [ON], [OFF]. (Not available when no source is selected and the clock is displayed.)
AUTO SCR (auto scroll)
Scrolls long items automatically: [ON], [OFF].
(Not available when the AUX or tuner is selected.)
14GB
Additional Information
Updating the Firmware
To update the firmware, visit the support site on the back cover, then follow the online instructions.
Note
During the update, do not remove the USB device.
Precautions
•Do not leave the front panel or audio devices on the dashboard.
•When the unit is turned on, the power antenna (aerial) extends automatically.
•Do not splash liquid onto the unit.
Moisture condensation
Do not splash liquid onto the discs. When moisture condensation occur inside the unit, remove the disc and wait for about an hour for it to dry out; otherwise the unit will not operate properly.
Notes on discs
•Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight.
•Wipe the discs with a
cleaning cloth from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners.
•This unit is designed to play discs that conform
to the Compact Disc (CD) standard. DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this unit.
•Discs that this unit CANNOT play
–Discs with labels, stickers, or sticky tape or paper attached. Doing so may cause a malfunction, or may ruin the disc.
–Discs with non-standard shapes (e.g., heart, square, star). Attempting to do so may damage the unit.
–8 cm (3 1/4 in) discs.
Notes on CD-R/CD-RW discs
•If the multi-session disc begins with a CDDA session, it is recognized as a CD-DA disc, and other sessions are not played.
•Discs that this unit CANNOT play
–CD-R/CD-RW of poor recording quality.
–CD-R/CD-RW recorded with an incompatible recording device.
–CD-R/CD-RW which is finalized incorrectly.
–CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet/Romeo or multi-session.
Playback order of audio files
Folder (album) |
Audio file (track) |
15GB
About iPod
•You can connect to the following iPod models. Update your iPod devices to the latest software before use.
Compatible iPhone/iPod models
Compatible Model |
USB |
|
|
iPhone X |
|
|
|
iPhone 8 |
|
|
|
iPhone 8 Plus |
|
|
|
iPhone 7 |
|
|
|
iPhone 7 Plus |
|
|
|
iPhone SE |
|
|
|
iPhone 6s |
|
|
|
iPhone 6s Plus |
|
|
|
iPhone 6 |
|
|
|
iPhone 6 Plus |
|
|
|
iPhone 5s |
|
|
|
iPhone 5c |
|
|
|
iPhone 5 |
|
|
|
iPhone 4s |
|
|
|
iPod touch (6th generation) |
|
|
|
iPod touch (5th generation) |
|
|
|
iPod nano (7th generation) |
|
|
|
•Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with an Apple product may affect wireless performance.
If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.
Maintenance
Cleaning the connectors
Avoid touching the connectors directly. The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 7) and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged.
Note
For safety, do not remove the front panel while driving.
16GB
Specifications
Tuner section
FM
Tuning range:
When [AREA] is set to [EUROPE]: 87.5 MHz – 108.0 MHz
When [AREA] is set to [RUSSIA]: FM1/FM2: 87.5 MHz – 108.0 MHz
(at 50 kHz step)
FM3: 65 MHz – 74 MHz (at 30 kHz step) Usable sensitivity: 7 dBf
Signal-to-noise ratio: 73 dB Separation: 50 dB at 1 kHz
MW/LW
Tuning range:
531 kHz – 1,602 kHz (MW),
153 kHz – 279 kHz (LW) Sensitivity: MW: 26 μV, LW: 50 μV
CD Player section
Signal-to-noise ratio: 95 dB
Frequency response: 20 Hz – 20,000 Hz Maximum number*1 of:
Folders (albums)*2: 150
Files (tracks) and folders*3: 300 Displayable characters for a folder/file
name:
32 (Joliet)/64 (Romeo) Corresponding codec: MP3 (.mp3), WMA
(.wma)
*1 CD-R/CD-RW only
*2 including the root folder
*3 may be less than the measured value if folder/ file names contain many characters
USB Player section
Interface: USB (Full speed) Maximum current: 1 A
Maximum number of recognizable folders and files:
Folders (albums): 256
Files (tracks) per folder: 256 Compatible Android Open Accessory
protocol (AOA): 2.0
Corresponding codec: MP3 (.mp3)
Bit rate: 8 kbps – 320 kbps (Supports VBR (Variable Bit Rate))
Sampling rate: 16 kHz – 48 kHz WMA (.wma)
Bit rate: 32 kbps – 192 kbps (Supports VBR (Variable Bit Rate))
Sampling rate: 32 kHz, 44.1 kHz, 48 kHz
FLAC (.flac)
Bit depth: 16 bit, 24 bit Sampling rate: 44.1 kHz, 48 kHz
Supported file system: FAT16, FAT32
Power amplifier section
Output: Speaker outputs Speaker impedance: 4 Ω – 8 Ω
Maximum power output: 55 W × 4 (at 4 Ω)
General
Power requirements: 12 V DC car battery (negative ground (earth))
Rated current consumption: 10 A Dimensions:
Approx. 178 mm × 50 mm × 176 mm (7 1/8 in × 2 in × 7 in) (w/h/d)
Mounting dimensions:
Approx. 182 mm × 53 mm × 159 mm (7 1/4 in × 2 1/8 in × 6 3/8 in) (w/h/d)
Mass: Approx. 1.2 kg (2 lb 11 oz) Package contents:
Main unit (1)
Parts for installation and connections (1 set)
Ask the dealer for detailed information.
Design and specifications are subject to change without notice.
17GB
Copyrights
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.
Apple, iPhone, iPod, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
Android is a trademark of Google LLC.
libFLAC
Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
–Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
–Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
–Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Troubleshooting
The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.
For details on using the fuse and removing the unit from the dashboard, see “Connection/Installation” (page 22).
If the problem is not solved, visit the support site on the back cover.
General
No sound or the sound is very low.
The position of the fader control [FADER] is not set for a 2-speaker system.
The volume of the unit and/or connected device is very low.
–Increase the volume of the unit and connected device.
No beep sound.
An optional power amplifier is connected and you are not using the built-in amplifier.
Stored stations and correct time are erased.
The fuse has blown.
Makes a noise when the position of the ignition is switched.
The leads are not matched correctly with the car’s accessory power connector.
During playback or reception, the demonstration mode starts.
If no operation is performed for 5 minutes with [DEMO-ON] set, the demonstration mode starts.
– Set [DEMO-OFF] (page 12).
The display disappears from/does not appear in the display window.
The connectors are dirty (page 16).
The display/illumination flashes.
The power supply is not sufficient.
–Check that the car battery supplies enough power to the unit. (The power requirement is 12 V DC.)
18GB
The operation buttons do not function. The disc will not eject.
The connection is not correct.
–Press DSPL and EQ for more than 2 seconds to reset the unit.
The contents stored in memory are erased.
The clock set automatically is not accurate.
The clock data on radio waves is not accurate.
– Set the clock manually (page 7).
Radio reception
The radio reception is poor. Static noise occurs.
Connect the antenna (aerial) firmly.
65 MHz to 74 MHz in FM3 cannot be tuned in.
[AREA] is set to [EUROPE].
– Set [AREA] to [RUSSIA] (page 12).
RDS
RDS services cannot be received (when [AREA] is set to [RUSSIA]).
FM3 is selected.
– Select FM1 or FM2.
RDS services are unavailable in the current region.
The SEEK starts after a few seconds of listening.
The station is non-TP or has weak signal.
– Deactivate TA (page 9).
No traffic announcements.
Activate TA (page 9).
The station does not broadcast any traffic announcements despite being TP.
– Tune in another station.
PTY displays [- - - - - - - -].
The current station is not an RDS station, or the radio reception is poor.
Program service name flashes.
There is no alternative frequency for the current station.
–Press / (SEEK –/+) while the program service name is flashing. [PI SEEK] appears and the unit starts searching for another frequency with the same PI (program identification) data.
CD playback
The disc does not play.
Defective or dirty disc.
The CD-R/CD-RW is not for audio use (page 15).
MP3/WMA files cannot be played.
The disc is incompatible with the MP3/ WMA format and version. For details on playable discs and formats, visit the support site on the back cover.
MP3/WMA files take longer to play than others.
The following discs take a longer time to start playback.
–A disc recorded with a complicated tree structure.
–A disc recorded in Multi Session.
–A disc to which data can be added.
USB device playback
A USB device takes longer to play.
The USB device contains files with a complicated tree structure.
The audio file cannot be played.
For details on supported formats, see “Specifications” (page 17).
If the audio file still cannot be played, refer to the operating instructions supplied with the USB device, or contact the manufacturer of the USB device.
Operations for skipping an album, skipping items (Jump mode), and searching a track by name (QuickBrowZer) cannot be performed.
Set [USB MODE] to [MSC/MTP] (page 13).
19GB
The sound cannot be output during playback in Android mode.
Check the status of the audio playback application on the Android smartphone.
Messages
The following messages may appear or flash during operation.
INVALID: The selected operation could be invalid.
READ
Wait until reading is complete and playback starts automatically. This may take some time depending on the file organization.
(underscore): The character cannot be displayed.
For CD playback:
CD ERROR
Clean or insert the disc correctly, or make sure the disc is not blank or defective.
CD NO DISC
Insert a disc containing playable files (page 17).
CD NO MUSIC
Insert a disc containing playable files (page 17).
CD PUSH EJT: The disc could not be ejected properly.
Press (eject).
or 
: The beginning or the end of the disc has been reached.
For USB device playback:
HUB NO SUPRT: USB hubs are not supported.
IPD STOP: iPod playback has finished.
Operate your iPod/iPhone to start playback.
NOT SUPPORT ANDROID MODE
A USB device not supporting AOA (Android Open Accessory) 2.0 is connected to the unit while [USB MODE] is set to [ANDROID].
– Set [USB MODE] to [MSC/MTP] (page 13).
USB ERROR
Connect the USB device again.
USB NO DEV
Make sure the USB device or USB cable is securely connected.
USB NO MUSIC
Connect a USB device containing playable files (page 17).
USB NO SUPRT
For details on the compatibility of your USB device, visit the support site on the back cover.
USB OVERLOAD: The USB device is overloaded.
Disconnect the USB device, then press SRC to select another source.
The USB device has a fault, or an unsupported device is connected.
For RDS operation:
NO AF: No alternative frequencies.
Press / (SEEK –/+) while the program service name is flashing. The unit starts searching for another frequency with the same PI (program identification) data ([PI SEEK] appears).
NO PI: No program identification. The selected station has no PI (program identification) data.
Select another station.
20GB
NO TP: No traffic programs.
The unit will continue searching for available TP stations.
For steering wheel remote control operation:
ERROR
Register again from the function where the error occurred (page 12).
TIMEOUT
Try completing the registration while [REGISTER] is blinking (about 6 seconds) (page 12).
For firmware update operation:
FILE ERROR: The updater is not stored in the USB device.
Store the updater in the USB device, then try again (page 15).
UPDATE ERROR PRESS ENTER: Firmware update is not completed properly.
Press ENTER to clear the message, then try again.
During the update, do not turn the ignition to the OFF position, nor remove the USB device (page 15).
If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of device playback trouble, bring the device that was used at the time the problem began.
21GB
Connection/Installation
Cautions
•Run all ground (earth) leads to a common ground (earth) point.
•Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
•Before making connections, turn the car ignition off to avoid short circuits.
•Connect the power supply lead to the unit and speakers before connecting it to the auxiliary power connector.
•Be sure to insulate any loose unconnected leads with electrical tape for safety.
Precautions
•Choose the installation location carefully so that the unit will not interfere with normal driving operations.
•Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
•Use only the supplied mounting hardware for a safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
Parts List for Installation
× 2
•This parts list does not include all the package contents.
•The bracket and the protection collar are attached to the unit before shipping. Before mounting the unit, use the release keys to remove the bracket from the unit. For details, see “Removing the protection collar and the bracket”
(page 25).
•Keep the release keys for future use as they are also necessary if you remove the unit from your car.
22GB
Connection
Subwoofer*1
*3
*3
Power amplifier*1
*2
For details, see “Making connections” (page 24).
See “Power connection diagram” (page 24) for details.
from a wired remote control (not supplied)*4
from a car antenna (aerial)*5
*1 Not supplied
*2 Speaker impedance: 4 Ω – 8 Ω × 4 *3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a wired remote control (not supplied).
For details on using the wired remote control, see “Using the wired remote control” (page 25).
*5 Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit.
23GB
Making connections
If you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power supply lead may damage the antenna (aerial).
To the car’s speaker connector
1 |
Rear speaker |
|
Purple |
|
|
Purple/black |
|
2 |
(right) |
|
|
|
|
|
striped |
3 |
Front speaker |
|
Gray |
|
|
Gray/black |
|
4 |
(right) |
|
|
|
|
|
striped |
5 |
Front speaker |
|
White |
|
|
White/black |
|
6 |
(left) |
|
|
|
|
|
striped |
7 |
Rear speaker |
|
Green |
|
|
Green/black |
|
8 |
(left) |
|
|
|
|
|
striped |
To the car’s power connector
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier when it is connected to a rear speaker lead.
Front speaker
Subwoofer
Notes
•Preparation of the rear speaker leads is required.
•Use a subwoofer with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.
Memory hold connection
When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.
Speaker connection
•Before connecting the speakers, turn the unit off.
•Use speakers with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.
12 |
continuous power |
Yellow |
|
supply |
|
|
power antenna |
|
13 |
(aerial) /power |
Blue/white |
|
amplifier control (REM |
striped |
|
OUT) |
|
15 |
switched power |
Red |
supply |
||
16 |
ground (earth) |
Black |
|
|
|
Power connection diagram
Check your car’s auxiliary power connector, and match the connections of leads correctly depending on the car.
Auxiliary power connector
24GB
Common connection
|
Red |
|
|
Red |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Yellow |
Yellow |
|
|
|
|
|
12 |
continuous power |
|
Yellow |
supply |
|
||
15 |
switched power supply |
Red |
|
|
|
|
|
When the positions of the red and yellow leads are inverted
Red |
Red |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Yellow |
Yellow |
|
|
|
|
|
12 |
switched power supply |
Yellow |
|
15 |
continuous power |
|
Red |
supply |
|
||
|
|
|
|
When the car without ACC position
Red Red
Yellow |
Yellow |
After matching the connections and switching power supply leads correctly, connect the unit to the car’s power supply. If you have any questions and problems connecting your unit that are not covered in this manual, consult the car dealer.
Using the wired remote control
1To enable the wired remote control, set [STR CONTROL] in [SET STEERING] to [PRESET] (page 12).
Installation
Removing the protection collar and the bracket
Before installing the unit, remove the protection collar and the bracket from the unit.
1Pinch both edges of the protection collar , then pull it out.
2Insert both release keys until they click, and pull down the bracket , then pull up the unit to separate.
Face the hook inwards.
25GB
Mounting the unit in the dashboard
Before installing, make sure the catches on both sides of the bracket are bent inwards 2 mm (3/32 in).
1Position the bracket inside the dashboard, then bend the claws outward for a tight fit.
182 mm (7 1/4 in)
53 mm (2 1/8 in) 
Catch
2Mount the unit onto the bracket , then attach the protection collar .
Notes
•If the catches are straight or bent outwards, the unit will not be installed securely and may spring out.
•Make sure the 4 catches on the protection collarare properly engaged in the slots of the unit.
Detaching and attaching the front panel
For details, see “Detaching the Front Panel” (page 7).
Resetting the unit
For details, see “Resetting the Unit” (page 7).
Fuse replacement
When replacing the fuse, be sure to use one
matching the amperage rating stated on the original fuse. If the fuse blows, check the power
connection and replace the
fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
26GB
Für mögliche spätere Service-Anfragen, notieren Sie sich bitte vor der Installation Ihres Gerätes hier die Seriennummer: S/N:___________________________
Hinweis: Die 7-stellige Seriennummer finden Sie oben auf der Verpackung des Gerätes oder unten auf dem Gerät selber.
Installieren Sie das Gerät aus Sicherheitsgründen unbedingt im Armaturenbrett des Fahrzeugs, denn die Rückseite des Geräts erwärmt sich bei Betrieb.
Erläuterungen dazu finden Sie unter „Anschluss/Installation“ (Seite 25).
Hergestellt in Thailand
Dieses Produkt wurde als Lasergerät der Klasse 1 gemäß IEC/EN 60825-1:2007 und IEC/EN 60825-1:2014 eingestuft.
Emissionsdauer: kontinuierlich
Laserausgangsleistung: unter 55,8 μW
Wellenlänge: 775 nm bis 800 nm
Das Typenschild mit Betriebsspannung usw. befindet sich an der Geräteunterseite.
Die Gültigkeit des CE-Zeichens beschränkt sich auf Länder, in denen es gesetzlich vorgeschrieben ist, hauptsächlich in Ländern des Europäischen Wirtschaftsraums (EWR).
Hiermit erklärt Sony Corporation, dass diese Funkanlage der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EUKonformitätserklärung ist unter der folgenden Internetadresse verfügbar: http://www.compliance.sony.de/
Dieses Gerät ist auf den Gebrauch mit der/ den zulässigen Softwareversion(en) ausgelegt, die in der EUKonformitätserklärung angegeben ist/sind. Die Software, mit der dieses Gerät ausgestattet ist, entspricht den grundlegenden Anforderungen der Richtlinie 2014/53/EU.
Die Softwareversion kann unter dem Punkt Firmware-Konfiguration des Menüs Allgemeine Einstellungen überprüft werden.
Hinweis für Kunden: Die folgenden Informationen gelten nur für Geräte, die in Ländern verkauft werden, in denen EU-Richtlinien gelten
Dieses Produkt wurde von oder für die Sony Corporation hergestellt.
EU Importeur: Sony Europe Limited. Anfragen an den Importeur oder zur Produktkonformität auf Grundlage der Gesetzgebung in Europa senden Sie bitte an den Bevollmächtigten Sony Belgium, bijkantoor van Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem, Belgien.
Entsorgung von gebrauchten Batterien und Akkus und gebrauchten elektrischen und elektronischen Geräten
(anzuwenden in den Ländern der Europäischen Union und anderen Ländern mit einem separaten Sammelsystem für diese Produkte)
Das Symbol auf dem Produkt, der Batterie/ dem Akku oder der Verpackung weist darauf hin, dass das Produkt oder die Batterie/der Akku nicht als normaler Haushaltsabfall zu behandeln sind. Ein zusätzliches chemisches Symbol Pb (Blei) unter der durchgestrichenen Mülltonne bedeutet, dass die Batterie/der Akku einen Anteil von mehr als 0,004 % Blei enthält. Durch Ihren Beitrag zum korrekten Entsorgen des Produktes und der Batterie/des Akkus schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet. Materialrecycling hilft, den Verbrauch von Rohstoffen zu verringern. Bei Produkten, die auf Grund ihrer Sicherheit, der Funktionalität oder als Sicherung vor Datenverlust eine ständige Verbindung zur eingebauten Batterie/zum eingebauten Akku benötigen, sollte die Batterie/der Akku nur durch qualifiziertes Servicepersonal ausgetauscht werden. Um sicherzustellen, dass das Produkt und die Batterie/der Akku korrekt entsorgt werden, geben Sie das Produkt zwecks Entsorgung an einer geeigneten Annahmestelle für das Recycling von elektrischen und elektronischen Geräten ab. Für alle anderen Batterien/Akkus entnehmen Sie die Batterie/den Akku bitte
2DE
entsprechend dem Kapitel über die sichere Entfernung der Batterie/des Akkus. Geben Sie die Batterie/den Akku an einer geeigneten Annahmestelle für das Recycling von Batterien/Akkus ab. Weitere Informationen über das Recycling dieses Produkts oder der Batterie/des Akkus erhalten Sie von Ihrer Gemeinde, den kommunalen Entsorgungsbetrieben oder dem Geschäft, in dem Sie das Produkt gekauft haben. Hinweis für Lithiumbatterien: Bitte geben Sie nur entladene Batterien an den Sammelstellen ab. Wegen Kurzschlussgefahr überkleben Sie bitte die Pole der Batterie mit Klebestreifen. Sie erkennen Lithiumbatterien an den Abkürzungen Li oder CR.
ACHTUNG
Der Frequenzbereich 65 – 74 MHz ist in der europäischen Frequenzbereichszuordnungstabelle keinem Hörfunk zugewiesen und kann in Europa nicht verwendet werden.
Warnhinweis, wenn die Zündung Ihres Fahrzeugs nicht über eine Zubehörposition (ACC oder I) verfügt
Aktivieren Sie unbedingt die Abschaltautomatik (AUTO OFF) (Seite 14). Das Gerät schaltet sich nach dem Ausschalten und dem Anzeigen der Uhrzeit (d. h. halten Sie OFF 1 Sekunde lang gedrückt) innerhalb einer bestimmte Zeit automatisch vollständig aus, um die Autobatterie zu schonen. Wenn Sie die Abschaltautomatik (AUTO OFF) nicht aktivieren, müssen Sie jedes Mal, wenn Sie die Zündung ausschalten, OFF gedrückt halten, bis die Anzeige ausgeblendet wird.
Haftungsausschluss für von Dritten angebotene Dienste
Von Dritten angebotene Dienste können ohne vorherige Ankündigung geändert, ausgesetzt oder eingestellt werden. Sony übernimmt in diesen Fällen keine Haftung.
3DE
Inhalt
Lage und Funktion der Teile und Bedienelemente . . . . . . . . . . . . . . . . . . . 5
Vorbereitungen
Abnehmen der Frontplatte . . . . . . . . . . . . . 7 Zurücksetzen des Geräts . . . . . . . . . . . . . . . 7 Einstellen der Uhr . . . . . . . . . . . . . . . . . . . . . 8 Überprüfen der Batteriespannung . . . . . . . 8 Anschließen eines USB-Geräts . . . . . . . . . . 8
Anschließen eines anderen tragbaren Audiogeräts. . . . . . . . . . . . . . . . . . . . . . . 9
Radioempfang
Radioempfang . . . . . . . . . . . . . . . . . . . . . . . 9
Das Radiodatensystem (RDS) . . . . . . . . . . 10
Wiedergabe
Wiedergeben von Discs . . . . . . . . . . . . . . . . 11 Wiedergabe mit einem USB-Gerät . . . . . . . 11 Suchen und Wiedergeben von Titeln . . . . 12
Einstellungen
Beenden des DEMO-Modus . . . . . . . . . . . 13 Grundlegende Einstellschritte . . . . . . . . . . 13 Allgemeine Einstellungen (GENERAL). . . . 14 Klangeinstellungen (SOUND). . . . . . . . . . . 15 Anzeigeeinstellungen (DISPLAY). . . . . . . . 16
Weitere Informationen
Aktualisieren der Firmware . . . . . . . . . . . . 17 Sicherheitsmaßnahmen. . . . . . . . . . . . . . . 17 Wartung. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Technische Daten . . . . . . . . . . . . . . . . . . . . 19 Störungsbehebung. . . . . . . . . . . . . . . . . . . 21 Meldungen . . . . . . . . . . . . . . . . . . . . . . . . . 23
Anschluss/Installation
Vorsichtsmaßnahmen . . . . . . . . . . . . . . . . 25 Teileliste für die Installation. . . . . . . . . . . . 25 Anschluss . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 28
4DE
Loading...