audio/video multi-channel receiver récepteur audiovisuel multicanal
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
D3-4-2-1-1_A1_En
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
IMPORTANT: THE MOULDED PLUG
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.
If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows;
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
D3-4-2-1-2-2*_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following section carefully.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 40 cm at top, 10 cm at rear, and 20 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.
D3-4-2-1-7b*_A1_En
Information for users on collection and disposal of old equipment and used batteries
Symbol for |
These symbols on the products, packaging, and/or accompanying documents mean |
||||||||
equipment |
that used electrical and electronic products and batteries should not be mixed with |
||||||||
|
|
|
|
|
|
|
|
|
general household waste. |
|
|
|
|
|
|
|
|
|
For proper treatment, recovery and recycling of old products and used batteries, |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
please take them to applicable collection points in accordance with your national |
|
|
|
|
|
|
|
|
|
legislation. |
|
|
|
|
|
|
|
|
|
By disposing of these products and batteries correctly, you will help to save valuable |
|
|
|
|
|
|
|
|
|
|
Symbol examples |
resources and prevent any potential negative effects on human health and the |
||||||||
for batteries |
environment which could otherwise arise from inappropriate waste handling. |
||||||||
|
|
|
|
|
|
|
|
|
For more information about collection and recycling of old products and batteries, |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
please contact your local municipality, your waste disposal service or the point of sale |
|
|
|
|
|
|
|
|
|
where you purchased the items. |
|
|
|
|
|
|
|
|
|
These symbols are only valid in the European Union. |
|
|
|
|
|
|
|
|
|
For countries outside the European Union: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If you wish to discard these items, please contact your local authorities or dealer and |
|
|
|
|
|
|
|
|
|
ask for the correct method of disposal. |
Pb
K058a_A1_En
Operating Environment
Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)
D3-4-2-1-7c*_A1_En
If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.
The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-1a_A1_En
CAUTION
TheSTANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-2a*_A1_En
This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.
K041_A1_En
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
Flow of settings on the receiver . . .7
01 Before you start
Checking what’s in the box. . . . . . . . . . . . . . . . 8 Installing the receiver . . . . . . . . . . . . . . . . . . . . 8
Loading the batteries . . . . . . . . . . . . . . . . . . . . 8
02 Controls and displays
Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Remote control . . . . . . . . . . . . . . . . . . . . . . . 13
Operating range of remote control unit. . . . . 14
03 Connecting your equipment
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Determining the speakers’ application . . . . . . 17 Other speaker connections . . . . . . . . . . . . . 18
Placing the speakers . . . . . . . . . . . . . . . . . . 19
Some tips for improving sound quality . . . . . 19 Connecting the speakers . . . . . . . . . . . . . . . . 20 Installing your speaker system . . . . . . . . . . . . 21 Bi-amping your speakers . . . . . . . . . . . . . . . 22 Bi-wiring your speakers . . . . . . . . . . . . . . . . 22 Selecting the Speaker system . . . . . . . . . . . . . 23
Front height setup . . . . . . . . . . . . . . . . . . . . 23 Front wide setup . . . . . . . . . . . . . . . . . . . . . 23 Speaker B setup . . . . . . . . . . . . . . . . . . . . . 23 Bi-Amping setup . . . . . . . . . . . . . . . . . . . . . 23 ZONE 2 setup . . . . . . . . . . . . . . . . . . . . . . . 23
About the audio connection . . . . . . . . . . . . . . 24 About the video converter. . . . . . . . . . . . . . . . 24 Connecting your TV and playback
components. . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting using HDMI . . . . . . . . . . . . . . . 25 Connecting your DVD player with no
HDMI output . . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting your TV with no HDMI input. . . . 28 Connecting a satellite/cable receiver or
other set-top box . . . . . . . . . . . . . . . . . . . . . . 29
Connecting a HDD/DVD recorder, VCR and other video sources . . . . . . . . . . . . . . . . . . . . 29
Connecting other audio components . . . . . . . 30 About the WMA9 Pro decoder . . . . . . . . . . . 30 Connecting AM/FM antennas . . . . . . . . . . . . . 31 Connecting external antennas . . . . . . . . . . . 31
MULTI-ZONE setup. . . . . . . . . . . . . . . . . . . . . 32
Making MULTI-ZONE connections . . . . . . . . 32 Connecting Optional Bluetooth ADAPTER . . . 33 Connecting to the network through LAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connecting an HDMI-equipped component
to the front panel input . . . . . . . . . . . . . . . . . . 34 Connecting to the front panel video terminal . . . 35
Connecting an iPod . . . . . . . . . . . . . . . . . . . . 35
Connecting a USB device . . . . . . . . . . . . . . . . 36 Connecting a USB device for Advanced
MCACC output . . . . . . . . . . . . . . . . . . . . . . . . 36
Connecting an IR receiver. . . . . . . . . . . . . . . . 37 Operating other Pioneer components with
this unit’s sensor . . . . . . . . . . . . . . . . . . . . . . 37
Plugging in the receiver . . . . . . . . . . . . . . . . . 38
04 Basic Setup
Changing the OSD display language
(OSD Language) . . . . . . . . . . . . . . . . . . . . . . . 39
Automatically conducting optimum sound tuning (Auto MCACC) . . . . . . . . . . . . . . . . . . . 39
Problems when using the Auto MCACC
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 The Input Setup menu . . . . . . . . . . . . . . . . . . 42
Input function default and possible
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
05 Basic playback
Playing a source . . . . . . . . . . . . . . . . . . . . . . . 44
Playing a source with HDMI connection . . . . 45
Playing an iPod . . . . . . . . . . . . . . . . . . . . . . . 45
Playing back files stored on an iPod . . . . . . . 45
Playing a USB device . . . . . . . . . . . . . . . . . . . 47
Playing back audio files stored on a USB memory device. . . . . . . . . . . . . . . . . . . . . . . 47
Playing back photo files stored on a USB memory device. . . . . . . . . . . . . . . . . . . . . . . 48
About playable file formats . . . . . . . . . . . . . . 49
Listening to the radio . . . . . . . . . . . . . . . . . . . 50 Improving FM sound . . . . . . . . . . . . . . . . . . 50
Using Neural Surround . . . . . . . . . . . . . . . . 50 Tuning directly to a station . . . . . . . . . . . . . . 50 Saving station presets . . . . . . . . . . . . . . . . . 51 Naming station presets . . . . . . . . . . . . . . . . 51 Listening to station presets. . . . . . . . . . . . . . 51 An introduction to RDS . . . . . . . . . . . . . . . . 52
Bluetooth® ADAPTER for Wireless
Enjoyment of Music . . . . . . . . . . . . . . . . . . . . 53 Wireless music play . . . . . . . . . . . . . . . . . . . 53
Pairing the Bluetooth ADAPTER and
Bluetooth wireless technology device . . . . . . 53 Listening to music contents of a
Bluetooth wireless technology device
with your system . . . . . . . . . . . . . . . . . . . . . 54
Listening to Internet radio stations . . . . . . . . . 55 Programming the Internet radio stations . . . 55
06 Listening to your system
Auto playback . . . . . . . . . . . . . . . . . . . . . . . . 57
Listening in surround sound. . . . . . . . . . . . . . 57 Standard surround sound . . . . . . . . . . . . . . 57 Using the Advanced surround effects. . . . . . 59
Listening in stereo . . . . . . . . . . . . . . . . . . . . . 59
Using Front Stage Surround Advance . . . . . . . 60
Using Stream Direct. . . . . . . . . . . . . . . . . . . . 60
Selecting MCACC presets. . . . . . . . . . . . . . . . 61 Choosing the input signal. . . . . . . . . . . . . . . . 61 Better sound using Phase Control . . . . . . . . . 62
07 Control with HDMI function
Making Control with HDMI connections . . . . . 63
HDMI Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Before using synchronization . . . . . . . . . . . . . 65 About synchronized operations. . . . . . . . . . . . 65
About connections with a product of a different brand that supports the Control
with HDMI function . . . . . . . . . . . . . . . . . . . 66
Setting the PQLS function . . . . . . . . . . . . . . . 66 Cautions on the Control with HDMI
function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
08 Using other functions
Setting the Audio options . . . . . . . . . . . . . . . . 68 Setting the Video options . . . . . . . . . . . . . . . . 71 Switching the speaker terminals. . . . . . . . . . . 73 Using the MULTI-ZONE controls . . . . . . . . . . . 73 Making an audio or a video recording . . . . . . . 74 Reducing the level of an analog signal . . . . . . 75
Using the sleep timer . . . . . . . . . . . . . . . . . . . 75 Dimming the display . . . . . . . . . . . . . . . . . . . 75
Checking your system settings . . . . . . . . . . . . 75
Resetting the system . . . . . . . . . . . . . . . . . . . 76
Default system settings . . . . . . . . . . . . . . . . 76
09 Controlling the rest of your system
Operating multiple receivers. . . . . . . . . . . . . . 77 Setting the remote to control other
components. . . . . . . . . . . . . . . . . . . . . . . . . . 77
Selecting preset codes directly . . . . . . . . . . . . 78 Programming signals from other remote controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Erasing one of the remote control button settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Resetting the input assignment of one of |
|
the input function buttons . . . . . . . . . . . . . . . |
80 |
Direct function . . . . . . . . . . . . . . . . . . . . . . . . |
80 |
Multi operation and System off . . . . . . . . . . . . |
81 |
Programming a Multi operation or |
|
a shutdown sequence . . . . . . . . . . . . . . . . . |
81 |
Using multi operations . . . . . . . . . . . . . . . . |
82 |
Using System off . . . . . . . . . . . . . . . . . . . . . |
82 |
Erasing the settings for the |
|
multi-operation . . . . . . . . . . . . . . . . . . . . . . |
82 |
Clearing all the remote control settings. . . . . . |
83 |
Default preset codes . . . . . . . . . . . . . . . . . . |
83 |
Controlling components . . . . . . . . . . . . . . . . . |
83 |
10 The Advanced MCACC menu
Making receiver settings from the Advanced MCACC menu . . . . . . . . . . . . . . . . . . . . . . . . 86
Automatic MCACC (Expert). . . . . . . . . . . . . . . 87
Manual MCACC setup . . . . . . . . . . . . . . . . . . 90 Fine Channel Level . . . . . . . . . . . . . . . . . . . . 91
Fine Speaker Distance . . . . . . . . . . . . . . . . . 91
Standing Wave. . . . . . . . . . . . . . . . . . . . . . . 92
Acoustic Calibration EQ Adjust. . . . . . . . . . . 93 Acoustic Calibration EQ Professional . . . . . . 93
Checking MCACC Data. . . . . . . . . . . . . . . . . . 96 Speaker Setting . . . . . . . . . . . . . . . . . . . . . . 96 Channel Level . . . . . . . . . . . . . . . . . . . . . . . 96 Speaker Distance. . . . . . . . . . . . . . . . . . . . . 96 Standing Wave. . . . . . . . . . . . . . . . . . . . . . . 97 Acoustic Cal EQ . . . . . . . . . . . . . . . . . . . . . . 97 Output MCACC data . . . . . . . . . . . . . . . . . . 97
Data Management . . . . . . . . . . . . . . . . . . . . . 98
Renaming MCACC presets. . . . . . . . . . . . . . 98 Copying MCACC preset data . . . . . . . . . . . . 98 Clearing MCACC presets . . . . . . . . . . . . . . . 99
11 The System Setup and Other Setup menus
Making receiver settings from the
System Setup menu . . . . . . . . . . . . . . . . . . . 100 Manual speaker setup . . . . . . . . . . . . . . . . . 100
Speaker system setting . . . . . . . . . . . . . . . 101
Speaker Setting . . . . . . . . . . . . . . . . . . . . . 102 Channel Level . . . . . . . . . . . . . . . . . . . . . . 103 Speaker Distance. . . . . . . . . . . . . . . . . . . . 103 X-Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Network Setup menu . . . . . . . . . . . . . . . . . . 104
IP address/Proxy setting. . . . . . . . . . . . . . . 104 Checking the MAC address . . . . . . . . . . . . 105
The Other Setup menu . . . . . . . . . . . . . . . . . 106 Volume Setup . . . . . . . . . . . . . . . . . . . . . . 106
Remote Control Mode Setup . . . . . . . . . . . 107 Flicker Reduction Setup . . . . . . . . . . . . . . . 107
Español Nederlands Italiano Français Deutsch English
12 Additional information
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . 108 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 No sound . . . . . . . . . . . . . . . . . . . . . . . . . 109 Other audio problems . . . . . . . . . . . . . . . . 110 Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Professional Calibration EQ graphical
output. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Remote control . . . . . . . . . . . . . . . . . . . . . 115 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Important information regarding the HDMI connection . . . . . . . . . . . . . . . . . . . . . . . . 117 USB interface . . . . . . . . . . . . . . . . . . . . . . 118 ADAPTER PORT . . . . . . . . . . . . . . . . . . . . 119 Internet radio . . . . . . . . . . . . . . . . . . . . . . 119
About iPod . . . . . . . . . . . . . . . . . . . . . . . . . 121
Surround sound formats . . . . . . . . . . . . . . . 121
Dolby . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 DTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Windows Media Audio 9 Professional . . . . 121 Auto Surround, ALC and Stream Direct with different input signal formats . . . . . . . . . . . . 122
Preset code list . . . . . . . . . . . . . . . . . . . . . . 123 Specifications . . . . . . . . . . . . . . . . . . . . . . . 132 Cleaning the unit . . . . . . . . . . . . . . . . . . . . . 133
The unit is a full-fledged AV receiver equipped |
The colors of the steps indicate the following: |
|
with an abundance of functions and terminals. |
|
|
It can be used easily after following the |
Required setting item |
|
procedure below to make the connections and |
|
|
settings. |
Setting to be made as necessary |
|
|
|
|
|
|
|
•Checking what’s in the box (page 8)
•Loading the batteries (page 8)
•9.1 channel surround system (Front height)
•9.1 channel surround system (Front wide)
•7.1 channel surround system & Speaker B connection
•5.1 channel surround system & Front Biamping connection (High quality surround)
•5.1 channel surround system & ZONE 2 connection (Multi Zone)
•Some tips for improving sound quality (page 19)
•Connecting the speakers (page 20)
•Installing your speaker system (page 21)
•Bi-amping your speakers (page 22)
•About the audio connection (page 24)
•About the video converter (page 24)
•Connecting your TV and playback components (page 25)
•Connecting AM/FM antennas (page 31)
•Plugging in the receiver (page 38)
•Automatically conducting optimum sound tuning (Auto MCACC) (page 39)
(When using connections other than the recommended connections)
•Using the various listening modes
•Better sound using Phase Control (page 62)
•Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 87)
•Changing the channel level while listening (Tip on page 103)
•Switching on/off the Acoustic Calibration EQ, Sound retriever or Dialog Enhancement (page 68)
•Setting the PQLS function (page 66)
•Setting the Audio options (Tone, Loudness or Sound delay, etc.) (page 68)
•Setting the Video options (page 71)
•HDMI Setup (page 64)
•The Advanced MCACC menu (page 86)
•The System Setup and Other Setup menus (page 100)
•Operating multiple receivers (page 77)
•Setting the remote to control other components (page 77)
•Programming signals from other remote controls (page 78)
Español Nederlands Italiano Français Deutsch English
7
En
01 Before you start
Chapter 1:
Please check that you’ve received the following supplied accessories:
•Setup microphone (cable: 5 m)
•Remote control unit
•AAA size IEC R03 dry cell batteries (to confirm system operation) x2
•AM loop antenna
•FM wire antenna
•iPod cable
•Power cord
•Warranty card
•These operating instructions
•When installing this unit, make sure to put it on a level and stable surface.
Don’t install it on the following places:
–on a color TV (the screen may distort)
–near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.
–in direct sunlight
–in damp or wet areas
–in extremely hot or cold areas
–in places where there is vibration or other movement
–in places that are very dusty
–in places that have hot fumes or oils (such as a kitchen)
•Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel becomes hot when the power is on (or right after it is turned off) and could cause burns.
8
The batteries included with the unit are to check initial operations; they may not last over a long period. We recommend using alkaline batteries that have a longer life.
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
•Never use new and old batteries together.
•Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
•Batteries with the same shape may have different voltages. Do not use different batteries together.
•When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.
•WARNING
Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.
En
Chapter 2:
Controls and displays
02
English
Front panel |
|
|
|
|
|
|
|
|
|
|
|
|
Deutsch |
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
|
|
|
8 |
|
|
9 |
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
AUDIO/ VIDEO MULTICHANNEL RECEIVER |
VSX-1020 |
|
|
|
|
PHASE |
|
|
|
|
|
|
|
TUNE |
|
|
|
|
|
|
CONTROL |
|
|
|
|
|
|
|
|
|
|
|
|
|
STANDBY/ON |
|
|
|
|
|
|
|
|
PRESET |
PRESET |
|
|
Français |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
INPUT |
|
|
|
|
|
|
|
|
TUNE |
|
MASTER |
|
|
|
|
|
|
|
ADVANCED |
|
|
iPod |
|
|
|
|
|
|
|
|
SPEAKERS |
CONTROL |
MULTI-ZONE ON/OFF |
MCACC |
PQLS |
HDMI |
iPhone |
BAND |
TUNER EDIT |
ENTER |
|
|
|
|
SELECTOR |
|
|
|
|
|
|
|
|
|
|
VOLUME |
|
|
PHONES |
LISTENING MODE |
iPod iPhone |
|
|
|
AUTO/ALC/DIRECT |
STEREO |
STANDARD ADV SURROUND |
DIRECT CONTROL |
|
VIDEO CAMERA |
|
|
|
|
iPod |
|
|
|
|
|
iPhone |
|
|
|
|
MCACC |
USB |
HDMI 5 |
|
|
|
SETUP MIC |
|
|
10 11 12 13 14 15
VSX-1020/VSX-1025
|
VIDEO 2 |
INPUT |
|
iPod |
|
|
|
iPhone |
|
|
|
USB |
|
MCACC |
VSX-920 |
VIDEO |
L |
AUDIO R SETUP MIC |
|
|
|
|
Select an input function.
2STANDBY/ON
Switches the receiver between on and standby.
See Switching the speaker terminals on page 73.
Receives the signals from the remote control (see Operating range of remote control unit on page 14).
14 16 13
If you’ve made MULTI-ZONE connections (see MULTI-ZONE setup on page 32) use these controls to control the sub zone from the main zone (see Using the MULTI-ZONE controls on page 73).
See Display on page 11.
ADVANCED MCACC – Lights when EQ is set to ON in the AUDIO PARAMETER menu.
PQLS – Lights when the PQLS feature is active (page 66).
HDMI – Blinks when connecting an HDMIequipped component; lights when the component is connected (page 25).
Español Nederlands Italiano
9
En
02 Controls and displays
iPod/iPhone – Lights to indicate iPod/ iPhone is connected (page 45).
BAND – Switches between the AM and FM radio bands (page 50).
TUNER EDIT – Use with TUNE /,
PRESET /and ENTER to memorize and name stations for recall (page 50).
TUNE / – Find radio frequencies (page 50).
PRESET / – Find preset stations (page 50).
Connect the headphones. When the headphones are connected, there is no sound output from the speakers.
11Listening mode buttons AUTO/ALC/DIRECT – Switches between Auto Surround (page 57), Auto Level Control mode and Stream Direct mode (page 60).
STEREO – Switches between stereo playback and Front Stage Surround Advance modes (page 60).
STANDARD – Press for Standard decoding and to switch between the various 2Pro Logic IIx and Neo:6 options (page 57).
ADV SURROUND – Switch between the various surround modes (page 59).
Change the receiver’s input to the iPod and enable iPod operations on the iPod (page 46).
Connect the supplied microphone (page 39).
Connect your Apple iPod as an audio and video source, or connect a USB device for audio and photo playback (page 35, 36).
15VSX-1020/VSX-1025 only: HDMI input connector
Use for connection to a compatible HDMI device (Video camera, etc.)(page 34).
16VSX-920 only: VIDEO 2 INPUT terminals
Use to connect your portable equipment such as camcorders, video games and portable audio/video equipment (page 35).
10
En
Controls and displays |
02 |
|
1 |
|
2 |
|
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 14 |
AUTO |
L |
C |
R |
2DIGITAL PLUS |
DSD PCM |
PQLS |
ALC |
|
ATT |
TUNED RDS |
|
|
|||
|
PCM |
SL |
|
SR |
2TrueHD WMA9Pro |
MULTI-ZONE |
|
STEREO |
|
|
|
||||
HDMI |
XC |
DTS HD ES 96/24 |
S.RTRV SOUND UP MIX OVER MONO |
|
|
dB |
|||||||||
DIGITAL |
XL |
XR |
|
|
|
|
|
|
|
|
|
|
|
||
ANALOG |
|
LFE |
MSTR CD TUNER |
iPod |
DVD |
TV |
|
VIDEO |
USB |
[ 4 ] |
|
||||
AUTO SURROUND |
|
CD-R |
BD |
DVR |
|
HDMI [ 2 ] |
[ 3 ] |
|
|||||||
STREAM DIRECT |
|
|
|
|
|
|
|
|
|
|
|
|
|||
2PROLOGIC |
x Neo:6 |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
ADV.SURROUND |
|
|
|
|
|
|
|
|
|
|
|
|
||
STEREO STANDARD |
|
|
|
|
|
|
|
|
|
|
|
|
|||
SP |
AB |
SLEEP |
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
15 |
16 |
17 |
|
|
|
18 |
|
|
|
|
|
|
19 |
Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input signal automatically (page 61).
Light to indicate the channels to which digital signals are being input.
L/R – Left front/Right front channel C – Center channel
SL/SR – Left surround/Right surround channel LFE – Low frequency effects channel (the (( )) indicators light when an LFE signal is being input) XL/XR – Two channels other than the ones above XC – Either one channel other than the ones above, the mono surround channel or matrix encode flag
Light when a signal encoded in the corresponding format is detected.
2DIGITAL – Lights with Dolby Digital decoding.
2 DIGITAL PLUS – Lights with Dolby Digital Plus decoding.
2TrueHD – Lights with Dolby TrueHD decoding. DTS – Lights with DTS decoding.
DTS HD – Lights with DTS-HD decoding. 96/24 – Lights with DTS 96/24 decoding.
WMA9 Pro – Lights to indicate that a WMA9 Pro signal is being decoded.
DSD PCM – Light during DSD (Direct Stream Digital) to PCM conversion with SACDs.
PCM – Lights during playback of PCM signals. MSTR – Lights during playback of DTS-HD Master Audio signal.
Lights when the MULTI-ZONE feature is active (page 73).
Lights when any of the Midnight, Loudness or tone controls feature is selected (page 68). Lights when Dialog Enhancement is switched on.
Lights when the Sound Retriever function is active (page 69).
AUTO SURROUND – Lights when the Auto Surround feature is switched on (page 57).
ALC – Lights when the ALC (Auto level control) mode is selected (page 60).
STREAM DIRECT – Lights when Direct/ Pure Direct is selected (page 60).
ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 59).
STEREO – Lights when stereo listening is switched on (page 59).
STANDARD – Lights when one of the Standard Surround modes is switched on (page 57).
Lights when Phase Control is switched on (page 62).
Español Nederlands Italiano Français Deutsch English
11
En
02 Controls and displays
Light to indicate reducing the level of an analog signal (page 75).
TUNED – Lights when a broadcast is being received.
STEREO – Lights when a stereo FM broadcast is being received in auto stereo mode.
MONO – Lights when the mono mode is set using MPX.
RDS – Lights when an RDS broadcast is received.
11
Lights when the sound is muted (page 14).
Shows the overall volume level.
“---” indicates the minimum level, and “+12dB” indicates the maximum level.
Light to indicate the input function you have selected.
Light when there are more selectable items when making the various settings.
Indicates the speaker terminal, A and/or B, to which audio signal output is currently set (page 73).
Lights when the receiver is in sleep mode (page 75).
2PRO LOGIC IIx – This lights to indicate 2Pro Logic II / 2Pro Logic IIx decoding (page 57).
Neo:6 – When one of the Neo:6 modes of the receiver is on, this lights to indicate Neo:6 processing (page 57).
Displays various system information.
12
Lights to indicate the receiver’s remote control mode setting. (Not displayed when set to 1.) (page 77)
En
Controls and displays
This section explains how to operate the remote control for the receiver.
|
|
|
|
|
10 |
|
RECEIVER MULTI |
|
|
SOURCE |
|
1 |
|
OPERATION |
|
|
|
|
R.SETUP |
|
|
||
2 |
|
|
|
||
BD |
DVD |
DVR/BDR |
HDMI |
||
3 |
TV |
CD |
NET RADIO ADAPTER |
||
iPod USB TUNER |
VIDEO |
|
TV CTRL |
||
|
|
||||
|
|
|
|
|
11 |
|
INPUT SELECT |
ZONE 2 |
RECEIVER |
||
4 |
|
|
|
|
12 |
|
|
|
MASTER |
||
|
|
INPUT |
VOLUME |
||
5 |
TV CONTROL |
|
13 |
||
|
|
|
|
|
The remote has been conveniently color-coded according to component control using the following system:
•White – Receiver control, TV control
•Blue – Other controls (See page 45, 47, 50, 53, 55 and 83.)
1 RECEIVER
This switches between standby and on for this receiver.
2MULTI OPERATION – Use to perform multi operations (page 81).
R.SETUP – Use to input the preset code when making remote control settings and to set the remote control mode (page 77).
|
CH |
VOL |
MUTE |
3 |
Input function buttons |
|
|
|
|
14 |
|||
|
AUDIO |
|
VIDEO |
Press to select control of other components |
||
6 |
PARAMETER |
|
PARAMETER |
(page 77). |
||
LIST |
TUNE |
TOOLS |
||||
4 |
ZONE 2 |
|||||
|
BAND |
|
GUIDE |
|||
|
TOP MENU |
|
T.EDIT |
|
|
|
7 |
PRESET |
ENTER |
PRESET |
Switch to perform operations in the sub zone |
||
|
|
|
(page 74).
8
9
PTY |
|
|
|
|
SEARCH |
|
|
|
RETURN |
HOME |
TUNE |
|
||
MENU |
|
|||
iPod CTRL |
|
|
|
|
|
PGM |
|
MENU |
|
HDD |
DVD |
|
|
|
|
PHASE CTRL |
STATUS |
||
TV/DTV |
MPX |
PQLS |
|
|
S.RETRIEVER |
|
MIDNIGHT AUDIO |
||
1 |
2 |
|
3 |
|
SIGNAL SEL MCACC |
SLEEP |
INFO |
||
4 |
5 |
|
6 |
DISP |
CH LEVEL A.ATT |
DIMMER |
|
||
7 |
8 |
|
9 |
|
D.ACCESS |
|
|
CLASS |
CH |
|
|
|
||
/CLR |
0 |
|
ENTER |
|
AUTO/ALC/ |
STEREO STANDARD ADV SURR |
|||
DIRECT |
LISTENING MODE
RECEIVER
These buttons are dedicated to control the TV assigned to the TV CTRL button.
– Turn on/off the power of the TV.
INPUT – Select the TV input signal.
CH +/– – Select channels.
VOL +/– – Adjust the volume on your TV.
Press RECEIVER first to access:
AUDIO PARAMETER – Use to access the Audio options (page 68).
VIDEO PARAMETER – Use to access the Video options (page 71).
HOME MENU – Use to access the Home Menu (pages 39, 42, 64, 86, 100 and 106).
RETURN – Press to confirm and exit the current menu screen.
02
Español Nederlands Italiano Français Deutsch English
13
En
02 Controls and displays
7 / / /, ENTER
Use the arrow buttons when setting up your surround sound system (page 86) and the Audio or Video options (page 68 or 71).
Press RECEIVER first to access:
PHASE CTRL – Switch on/off Phase Control (page 62).
STATUS – Check selected receiver settings (page 75).
PQLS – Select the PQLS setting (page 66).
S.RETRIEVER – Press to restore CD quality sound to compressed audio sources (page 69).
MIDNIGHT – Switches to Midnight or
Loudness listening (page 68).
SIGNAL SEL – Select an input signal (page 61).
MCACC – Switch between MCACC presets (page 61).
SLEEP – Use to put the receiver in sleep mode and select the amount of time before sleep (page 75).
CH LEVEL – Press repeatedly to select a channel, then use /to adjust the level (page 103).
A.ATT – Attenuates (lowers) the level of an analog input signal to prevent distortion (page 75).
DIMMER – Dims or brightens the display (page 75).
9LISTENING MODE controls AUTO/ALC/DIRECT – Switches between Auto Surround (page 57), Auto Level Control mode and Stream Direct mode (page 60).
STEREO – Switches between stereo playback and Front Stage Surround Advance modes (page 60).
STANDARD – Press for Standard decoding and to switch between the various 2Pro Logic IIx and Neo:6 options (page 57).
14
ADV SURR – Switch between the various surround modes (page 59).
Lights when a command is sent from the remote control (page 77).
Set the preset code of your TV’s manufacturer when controlling TV (page 78).
12 RECEIVER
Switches the remote to control the receiver (used to select the white commands (SIGNAL SEL, etc.)).
Switch to perform operations in the main zone. Also use to set up surround sound.
13MASTER VOLUME +/–
Set the listening volume.
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).
The remote control may not work properly if:
•There are obstacles between the remote control and the receiver’s remote sensor.
•Direct sunlight or fluorescent light is shining onto the remote sensor.
•The receiver is located near a device that is emitting infrared rays.
•The receiver is operated simultaneously with another infrared remote control unit.
30° 30°
7 m
En
Chapter 3:
Connecting your equipment
This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This page explains the kinds of components you can connect to make up your home theater system.
•Illustration shows the VSX-1020, however connections for the VSX-1025 and the VSX-920 are the same except where noted.
HDMI |
|
BD IN |
IN 1 |
IN 2 |
IN 3 |
|
IN 4 |
OUT |
|
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
|
|
|
|
||
ASSIGNABLE 1 |
4 |
|
|
|
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
ASSIGNABLE |
ADAPTER PORT |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN 2 |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPUT 5 V |
100 mA MAX) |
|
AC IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
(CD) (TV/SAT) |
(DVR/BDR) |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
COMPONENT VIDEO |
|
AUDIO |
|
|
|
|
|
|
|
PRE OUT |
|
|
|
|
|
|
|||
IN 1 |
ASSIGNABLE |
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
(DVD) |
|
(DVR/BDR) |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
|
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANTENNA |
|
|
|
|
|
PB |
|
|
PB |
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE SUBWOOFER |
|
|
|
|
|
|
|||
PR |
|
|
PR |
OUT |
OUT |
IN |
IN |
IN |
IN |
IN |
OUT |
IN |
|
|
AM LOOP |
FM UNBAL 75 |
|
|
|
|
|
|
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
|
SURROUND BACK |
|
SPEAKERS |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
MONITOR |
|
|
|
|
|
|
R |
|
L |
|
R |
|
L R |
L(Single) |
FRONT HEIGHT/WIDE/ B |
||
Y |
|
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
R |
L |
VIDEO
PB
IR CONTROL
IN OUT IN OUT
PR
SPEAKERS A
VSX-1020/VSX-1025
BD IN |
IN 1 |
IN 2 |
IN 3 |
OUT |
|
LAN |
COAXIAL ASSIGNABLE |
|
|
|
|
OPTICAL |
|
||||
HDMI |
|
|
|
|
(10/100) |
IN 1 |
IN 1 |
IN 2 |
ASSIGNABLE |
ADAPTER PORT |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPUT 5 V 100 mA MAX) |
|
1 |
3 |
|
|
|
|
|
|
|
(DVD) |
(TV/SAT) |
(DVR/BDR) |
|
|
|
AC IN |
|
COMPONENT VIDEO |
AUDIO |
|
|
|
|
|
|
|
PRE OUT |
|
|
|
|
|
|
||
IN 1 |
ASSIGNABLE |
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
|
(DVR/BDR) |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANTENNA |
|
|
|
|
|
PB |
|
PB |
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO 1 |
CD |
CD-R/TAPE |
SUBWOOFER |
|
|
|
|
|
|
|
PR |
|
PR |
OUT |
OUT |
IN |
IN |
IN |
IN |
IN |
OUT IN |
|
|
AM LOOP |
FM UNBAL 75 |
|
|
|
|
|
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
|
SURROUND BACK |
|
SPEAKERS |
|||
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
MONITOR |
|
|
|
|
|
|
|
R |
L |
R |
|
L R |
L(Single) |
FRONT HEIGHT/WIDE/ B |
|
Y |
|
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
R |
L |
VIDEO
PB
IR CONTROL
IN OUT IN OUT
PR
SPEAKERS A
VSX-920
03
Español Nederlands Italiano Français Deutsch English
15
En
03 Connecting your equipment
•Before making or changing the connections, switch off the power and disconnect the power cord from the power outlet. Plugging in should be the final step.
•The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input Setup menu on page 42 to change the assignments if other connections are used.
Input |
|
Input Terminals |
function |
Digital |
HDMI Component |
|
|
|
DVD |
COAX-1 |
IN 1 |
|
|
|
BD |
|
(BD) |
|
|
|
TV/SAT |
OPT-1 |
|
|
|
|
DVR/BDR |
OPT-2 |
IN 2 |
|
|
|
HDMI 1 |
|
(HDMI-1) |
|
|
|
HDMI 2 |
|
(HDMI-2) |
|
|
|
HDMI 3 |
|
(HDMI-3) |
|
|
|
HDMI 4a |
|
(HDMI-4) |
HDMI 5a |
|
(HDMI-5) |
(front panel) |
|
|
|
|
|
CD |
COAX-2a |
a. VSX-1020/VSX-1025 only
16
En
Connecting your equipment
This unit permits you to build various surround systems, in accordance with the number of speakers you have.
•Be sure to connect speakers to the front left and right channels (L and R).
•It is also possible to only connect one of the surround back speakers (SB) or neither.
Choose one from Plans [A] to [E] below.
*Default setting
• Speaker System setting: Normal(SB/FH)
FHR
FHL |
|
|
|
R |
|
L |
|
|
C |
SR |
|
|
||
SW |
|
|
SL |
SBR |
|
SBL |
||
|
A 9.1 ch surround system connects the left and right front speakers (L/R), the center speaker (C), the left and right front height speakers (FHL/FHR), the left and right surround speakers (SL/SR), the left and right surround back speakers (SBL/SBR), and the subwoofer (SW).
This surround system produces a more true-to- life sound from above.
03
[B] 9.1 channel surround system (Front |
English |
||
wide) |
|
|
|
|
|
|
|
• Speaker System setting: Normal(SB/FW) |
|
||
R |
|
|
Deutsch |
L |
FWR |
|
|
|
|
||
|
|
|
|
C |
|
SR |
|
|
|
|
|
SW |
|
|
|
FWL |
|
|
Français |
SL |
|
SBR |
|
|
|
||
|
|
|
|
SBL |
|
|
|
This plan replaces the left and right front |
|
||
height speakers shown in [A] with the left and |
Italiano |
||
sound over a wider area. |
|
|
|
right front wide speakers (FWL/FWR). |
|
||
This surround system produces a true-to-life |
|
||
[C] 7.1 channel surround system & |
Nederlands |
||
Speaker B connection |
|
|
|
|
|
|
|
• Speaker System setting: Speaker B |
|
||
R |
|
|
Español |
C |
|
|
|
L |
|
|
|
|
|
R |
|
|
SR |
L |
|
SW |
|
|
|
SL |
SBR |
|
|
|
Speaker B |
|
|
SBL |
|
|
With these connections you can simultaneously enjoy 5.1-channel surround sound in the main zone with stereo playback of the same sound on the B speakers. The same connections also allow for 7.1-channel surround sound in the main zone when not using the B speakers.
17
En
03 Connecting your equipment
• Speaker System setting: Front Bi-Amp
Bi-amping connection of the front speakers for high sound quality with 5.1-channel surround sound.
Front Bi-Amp
R
L
C
SW
SR
SL
• Speaker System setting: ZONE 2
With these connections you can simultaneously enjoy 5.1-channel surround sound in the main zone with stereo playback on another component in ZONE 2 (The selection of input devices is limited.)
|
Main zone |
R |
|
L |
|
C |
|
SW |
|
|
SR |
SL |
Sub zone |
|
R |
ZONE 2 |
L |
|
•The Speaker System setting must be made if you use any of the connections shown above other than [A] (see Speaker system setting on page 101).
•Sound does not come through simultaneously from the front height, front wide, speaker B and surround back speakers. Output speakers are different depending on the input signal or listening mode.
•Your favorite speaker connections can be selected even if you have fewer than 5.1 speakers (except front left/right speakers).
•When not connecting a subwoofer, connect speakers with low frequency reproduction capabilities to the front channel. (The subwoofer’s low frequency component is played from the front speakers, so the speakers could be damaged.)
•After connecting, be sure to conduct the Auto MCACC (speaker environment setting) procedure.
See Automatically conducting optimum sound tuning (Auto MCACC) on page 39.
18
En
Connecting your equipment |
03 |
Refer to the chart below for placement of the speakers you intend to connect.
|
FHL |
SW |
C |
FHR |
|
|
|||
|
|
|
|
|
|
L |
|
|
R |
FWL |
|
30 |
30 |
FWR |
|
|
|
||
|
|
60 |
|
60 |
SL |
|
120 |
|
120 |
|
|
60 |
SR |
|
|
|
|
|
SBL SB SBR
•Place the surround speakers at 120º from the center. If you, (1) use the surround back speaker, and, (2) don’t use the front height speakers / front wide speakers, we recommend placing the surround speaker right beside you.
•If you intend to connect only one surround back speaker, place it directly behind you.
•Place the left and right front height speakers at least 1 m directly above the left and right front speakers.
Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.
•The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.
•For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from the TV.
•If you’re going to place speakers around your CRT TV, use shielded speakers or place the speakers at a sufficient distance from your CRT TV.
•If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower angle.
•Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.
•It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.
•Surround and surround back speakers should be positioned 60 cm to 90 cm higher than your ears and tilted slightly downward. Make sure the speakers don’t face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.
•Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.
Español Nederlands Italiano Français Deutsch English
19
En
03 Connecting your equipment
Each speaker connection on the receiver comprises a positive (+) and negative (–) terminal. Make sure to match these up with the terminals on the speakers themselves.
•These speaker terminals carry
HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.
•Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.
A-Speaker terminals:
1 |
2 |
3 |
10 mm
B-Speaker terminals:
1 |
2 |
3 |
10 mm
20
•Please refer to the manual that came with your speakers for details on how to connect the other end of the speaker cables to your speakers.
•Use an RCA cable to connect the subwoofer. It is not possible to connect using speaker cables.
•Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.
En
Connecting your equipment
At the very least, front left and right speakers only are necessary. Note that your main surround speakers should always be connected as a pair, but you can connect just one surround back speaker if you like (it must be connected to the left surround back terminal).
The front height terminals can also be used for the front wide and Speaker B speakers.
|
|
|
|
|
|
|
Front height setting |
|
|
|
|
||||||
|
|
|
Front height right |
|
|
|
Front height left |
|
|||||||||
|
|
|
|
|
|
|
Front wide setting |
Front wide left |
|
||||||||
|
|
|
Front wide right |
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
Speaker B setting |
Speaker B - left |
|
||||||||
|
|
|
Speaker B - right |
|
|
|
|
|
|||||||||
Front right |
|
|
|
|
|
|
|
Center |
|
|
Subwoofer |
Front left |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LINE LEVEL |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INPUT |
|
|
HDMI |
BD IN |
IN 1 |
IN 2 |
IN 3 |
|
IN 4 |
OUT |
|
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
|
|
|
||
ASSIGNABLE 1 4 |
|
|
|
|
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
|
ASSIGNABLE |
ADAPTER PORT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN 1 |
IN 2 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPUT 5 V |
100 mA MAX) |
AC IN |
|
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
(CD) (TV/SAT) (DVR/BDR) |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
COMPONENT VIDEO |
|
AUDIO |
|
|
|
|
|
|
|
|
OUT |
|
|
|
|
|
|
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
IN 1 |
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
(DVR/BDR) |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANTENNA |
|
|
|
|
PB |
PB |
|
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE SUBWOOFER |
|
|
|
|
|
|||
PR |
PR |
|
OUT |
OUT |
IN |
IN |
IN |
IN |
IN |
OUT |
IN |
|
|
AM LOOP |
FM UNBAL 75 |
|
|
|
|
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
|
SURROUND BACK |
SPEAKERS |
||||
|
|
|
|
|
|
|
|
|
R |
|
|||||||
|
MONITOR |
|
|
|
|
|
|
|
|
L |
|
R |
|
L R |
L(Single) |
FRONT HEIGHT/WIDE/ B |
|
Y |
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
R L |
VIDEO
PB
IR CONTROL
IN OUT IN OUT
PR
SPEAKERS A
VSX-1020/VSX-1025
|
The surround back terminals |
|
|
|
can also be used for ZONE2. |
|
|
|
5.1 ch surround setting |
|
|
|
Not connected |
Not connected |
|
|
6.1 ch surround setting |
|
|
Surround right |
Not connected |
Surround back |
|
7.1 ch surround setting |
Surround left |
||
|
Surround back right |
Surround back left |
|
|
ZONE 2 setting |
|
|
|
ZONE 2 - right |
ZONE 2 - left |
|
03
Español Nederlands Italiano Français Deutsch English
21
En
03 Connecting your equipment
Front right |
|
|
|
|
|
Center |
|
|
|
|
|
Front left |
||||
|
|
|
|
High |
|
|
|
|
|
Subwoofer |
|
High |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
Bi-amp compatible |
|
Low |
|
|
|
|
|
|
|
|
|
|
Low |
Bi-amp compatible |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
speaker |
|
|
|
|
|
|
|
|
|
|
|
|
|
speaker |
|
HDMI |
BD IN |
IN 1 |
IN 2 |
IN 3 |
|
IN 4 |
OUT |
|
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
|
|
|
|
ASSIGNABLE 1 |
4 |
|
|
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
ASSIGNABLE |
ADAPTER PORT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN 2 |
IN |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPUT 5 V 100 mA MAX) |
|
AC IN |
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
(CD) (TV/SAT) (DVR/BDR) |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
COMPONENT VIDEO |
|
AUDIO |
|
|
|
|
|
|
|
OUT |
|
|
|
|
|
|
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
IN 1 |
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
(DVR/BDR) |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANTENNA |
|
|
|
|
PB |
PB |
|
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE SUBWOOFER |
|
|
|
|
|
||
PR |
PR |
|
OUT OUT IN |
IN |
IN |
IN |
IN |
OUT |
IN |
|
|
AM LOOP |
FM UNBAL 75 |
|
|
|
|
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
SURROUND BACK |
SPEAKERS |
|||||
|
|
|
|
|
|
|
|
R |
||||||||
|
MONITOR |
|
|
|
|
|
|
|
L |
|
R |
|
L R |
L(Single) FRONT HEIGHT/WIDE/ B |
||
Y |
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
R |
L |
|
VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PB |
|
|
|
|
IR |
CONTROL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
IN |
OUT |
IN OUT |
|
|
|
|
|
|
|
|
|
|
PR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SPEAKERS A |
|
|
|
|
VSX-1020/VSX-1025 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
Surround right |
Surround left |
|
Bi-amping is when you connect the high frequency driver and low frequency driver of your speakers to different amplifiers for better crossover performance. Your speakers must be bi-ampable to do this (having separate terminals for high and low) and the sound improvement will depend on the kind of speakers you’re using.
•Most speakers with both High and Low terminals have two metal plates that connect the High to the Low terminals. These must be removed when you are biamping the speakers or you could severely damage the amplifier. See your speaker manual for more information.
•If your speakers have a removable crossover network, make sure you do not remove it for bi-amping. Doing so may damage your speakers.
Your speakers can also be bi-wired if they support bi-amping.
•With these connections, the Speaker System setting makes no difference.
•To bi-wire a speaker, connect two speaker cords to the speaker terminal on the receiver.
•Don’t connect different speakers from the same terminal in this way.
•When bi-wiring as well, heed the cautions for bi-amping shown at the left.
22
En
Connecting your equipment |
03 |
The front height terminals can be used for front wide and Speaker B connections, in addition to for the front height speakers. Also, the surround back terminals can be used for biamping and ZONE 2 connections, in addition to for the surround back speakers. Make this setting according to the application.
*Default setting
See Connecting the speakers on page 20.
See Speaker system setting on page 101 to do this.
See Connecting the speakers on page 20.
See Speaker system setting on page 101 to do this.
You can listen to stereo playback in another room.
See Connecting the speakers on page 20.
See Speaker system setting on page 101 to do this.
Bi-amping connection of the front speakers for high sound quality with 5.1-channel surround sound.
1Connect a Bi-amp compatible speakers to the front and surround back speaker terminals.
See Bi-amping your speakers on page 22.
2Select ‘Front Bi-Amp’ from the Speaker System menu.
See Speaker system setting on page 101 to do this.
With these connections you can simultaneously enjoy 5.1-channel surround sound in the main zone with stereo playback on another component in ZONE 2.
See Connecting the speakers on page 20.
See Speaker system setting on page 101 to do this.
Español Nederlands Italiano Français Deutsch English
23
En
03 Connecting your equipment
There are several types of audio input and output terminals on this receiver. The receiver selects the first available signal in the following order when you choose AUTO as the input signal:
|
Types of cables and |
Transferable |
|
terminals |
audio signals |
priority |
HDMI |
HD audio |
|
|
|
signal |
Digital (Coaxial) |
Conventional |
|
||
Sound |
|
digital audio |
Digital (Optical) |
|
|
|
RCA (Analog) |
Conventional |
|
(White/Red) |
analog audio |
•With an HDMI cable, video and audio signals can be transferred in high quality over a single cable.
•When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket.
•When storing optical cable, coil loosely. The cable may be damaged if bent around
sharp corners.
The video converter ensures that all video sources are output through all of the MONITOR OUT jacks. The only exception is HDMI: since this resolution cannot be downsampled, you must connect your monitor/TV to the receiver’s HDMI video outputs when connecting this video source.1
If several video components are assigned to the same input function (see The Input Setup menu on page 42), the converter gives priority to HDMI, component, then composite (in that order).
|
Terminal for |
Terminal for |
||||
|
connection with |
connection with TV |
||||
qualitypicture |
source device |
|
monitor |
|
||
|
HDMI IN |
|
|
HDMI OUT |
|
|
High |
Y |
PB |
PR |
Y |
PB |
PR |
|
VIDEO IN |
|
MONITOR OUT |
|||
|
COMPONENT |
COMPONENT VIDEO |
||||
|
|
VIDEO IN |
|
|
VIDEO |
|
|
|
|
|
MONITOR OUT |
||
|
|
Video signals can be output |
|
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.
Note
1 • If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that some components (such as video game units) have resolutions that may not be converted. In this case, try switching Digital Video Conversion (in Setting the Video options on page 71) OFF.
•The signal input resolutions that can be converted from the component video input for the HDMI output are 480i/ 576i, 480p/576p, 720p and 1080i. 1080p signal cannot be converted.
•Only signals with an input resolution of 480i/576i can be converted from the component video input for the composite MONITOR OUT terminals.
24
En
Connecting your equipment
If you have an HDMI or DVI (with HDCP) equipped component (BD: Blu-ray disc player, etc.), you can connect it to this receiver using a commercially available HDMI cable.
If the TV and playback components support the Control with HDMI function, the convenient Control with HDMI functions can be used (see Control with HDMI function on page 63).
|
HDMI |
|
BD IN |
IN 1 |
IN 2 |
IN 3 |
|
IN 4 |
OUT |
|
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
||
|
ASSIGNABLE 1 |
4 |
|
|
|
|
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
(CD) |
(TV/SAT) (DVR/BDR) |
|
|
COMPONENT |
|
|
|
|
|
|
|
|
|
|
PRE OUT |
|
|
||
|
IN 1 |
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
(DVD) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PB |
|
B |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE |
SUBWOOFER |
|
|
||
|
PR |
|
PR |
|
OUT |
OUT |
IN |
IN |
IN |
IN |
IN |
OUT |
IN |
|
|
AM LOOP |
|
|
|
|
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
||||
|
|
|
|
|
|
|
|
|
|
|
R |
|||||
|
|
|
MONITOR |
|
|
|
|
|
|
|
|
|
L |
|
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
|
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PB |
|
|
|
|
|
|
IR |
CONTROL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
IN |
OUT |
IN OUT |
|
|
|
|
|
|
|
VSX-1020/ |
PR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SPEAKERS A |
||
VSX-1025 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This connection is |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
required in order to |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
listen to the sound of |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
the TV over the receiver. |
|
R ANALOG L |
OPTICAL |
|
HDMI IN |
AUDIO OUT |
DIGITAL OUT |
|
Select one |
|||
|
03
Nederlands Italiano Français Deutsch English
HDMI OUT |
HDMI OUT |
HDMI/DVI-compatible |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Other HDMI/DVI- |
HDMI/DVI-compatible TV |
|||||||||||||||||
Blu-ray disc player |
equipped component |
|
|
|
|
|
|
|
•For input components, connections other than HDMI connections are also possible (see Connecting your DVD player with no HDMI output on page 27).
•If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
Español
25
En
03 Connecting your equipment
The HDMI connection transfers uncompressed digital video, as well as almost every kind of digital audio that the connected component is compatible with, including DVDVideo, DVD-Audio, SACD, Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio (see below for limitations), Video CD/Super VCD and CD. See About the video converter on page 24 for more on HDMI compatibility.
This receiver incorporates High-Definition Multimedia Interface (HDMI®) technology.
This receiver supports the functions described below through HDMI connections.2
•Digital transfer of uncompressed video (contents protected by HDCP (1080p/24, 1080p/60, etc.))
•3D signal transfer3
•Deep Color signal transfer3
•x.v.Color signal transfer3
•Input of multi-channel linear PCM digital audio signals (192 kHz or less) for up to 8 channels
•Input of the following digital audio formats:4
– Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio (Dolby TrueHD, DTS-HD Master Audio, DTS-HD High Resolution Audio), DVD-Audio, CD, SACD (DSD signal), Video CD, Super VCD
•Synchronized operation with components using the Control with HDMI function (see
Control with HDMI function on page 63).
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.
“x.v.Color” and x.v.Color logo are trademarks of Sony Corporation.
Note
1 • An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVI HDMI) to do so. A DVI connection, however, does not support audio signals. Consult your local audio dealer for more information.
•If you connect a component that is not compatible with HDCP, an HDCP ERROR message is displayed on the front panel display. Some components that are compatible with HDCP still cause this message to be displayed, but so long as there is no problem with displaying video this is not a malfunction.
•Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.
•This receiver supports SACD, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master Audio. To take advantage of these formats, however, make sure that the component connected to this receiver also supports the corresponding format.
2• Use a High Speed HDMI® cable. If an HDMI cable other than a High Speed HDMI® cable is used, it may not work properly.
•When an HDMI cable with a built-in equalizer is connected, it may not operate properly.
3Signal transfer is only possible when connected to a compatible component.
4• HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the audio may occur when switching between audio formats or beginning playback.
•Turning on/off the device connected to this unit's HDMI OUT terminal during playback, or disconnecting/ connecting the HDMI cable during playback, may cause noise or interrupted audio.
26
En
Connecting your equipment |
03 |
This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no HDMI output) to the receiver.
|
|
|
|
|
DVD player etc. |
|
Select one |
|
Select one |
||
COMPONENT VIDEO OUT |
VIDEO OUT |
AUDIO OUT |
DIGITAL OUT |
||
PR |
PB |
Y |
R |
ANALOG L |
COAXIAL OPTICAL |
|
|
|
HDMI |
BD IN |
IN 1 |
IN 2 |
IN 3 |
|
IN 4 |
OUT |
1 |
ASSIGNABLE |
|
OPTICAL |
|
|
ASSIGNABLE 1 |
4 |
|
|
|
|
|
|
|
IN |
IN 1 |
ASSIGNABLE |
AD |
|
|
|
|
|
|
|
|
|
|
|
|
IN 2 |
||
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPUT 5 |
|
|
|
|
|
|
|
|
|
|
(DVD) (CD) |
(TV/SAT) |
(DVR/BDR) |
|
|
COMPONENT VIDEO |
|
AUDIO |
|
|
|
|
|
|
PRE OUT |
|
|
|
|
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
|
|||
IN 1 |
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
) |
(DVR/BDR) |
L |
|
|
|
|
|
|
|
|
|
|
|
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
B |
PB |
|
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
CD-R/TAPE |
SUBWOOFER |
|
|
|
||
R |
PR |
|
OUT |
OUT |
IN |
IN |
IN |
OUT |
IN |
|
|
AM LOOP |
F |
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
|
||||
|
|
|
|
|
|
|
|
L |
|||||
|
MONITOR |
|
|
|
|
|
|
R |
|
L |
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
PB |
|
|
|
|
|
IR |
CONTROL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
IN |
OUT |
IN OUT |
|
|
|
|
|
|
PR
VSX-1020/ SPEAKERS A
VSX-1025
This connection is required in order to listen to the sound of the TV over the receiver.
R ANALOG L |
OPTICAL |
|
AUDIO OUT |
DIGITAL OUT |
|
Select one |
HDMI IN |
Español Nederlands Italiano Français Deutsch English
HDMI/DVI-compatible TV
•If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
•If the connection was made using an optical cable, you’ll need to tell the receiver which digital input you connected the DVD player to (see The Input Setup menu on page 42).
27
En
03 Connecting your equipment
This diagram shows connections of a TV (with no HDMI input) and DVD player (or other playback component) to the receiver.
•With these connections, the picture is not output to the TV even if the DVD player is connected with an HDMI cable. Connect the DVD player’s video signals using a composite or component cord.
|
|
|
|
DVD player etc. |
||
|
Select one |
|
|
Select one |
||
COMPONENT VIDEO OUT |
VIDEO OUT |
HDMI OUT |
AUDIO OUT |
DIGITAL OUT |
||
PR |
PB |
Y |
|
R |
ANALOG L |
COAXIAL OPTICAL |
|
|
|
|
•If the connection was made using an optical cable, you’ll need to tell the receiver which digital input you connected the DVD player to (see The Input Setup menu on page 42).
VSX-1020/ VSX-1025
HDMI |
BD IN |
IN 1 |
IN 2 |
IN 3 |
IN 4 |
OUT |
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
|
ASSIGNABLE 1 |
4 |
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
|
IN 2 |
|
|
|
|
|
|
|
|
|
|
|
|
(OUTPU |
|
|
|
|
|
|
|
|
(DVD) |
(CD) |
(TV/SAT) |
(DVR/BDR) |
COMPONENT VIDEO |
AUDIO |
|
|
|
|
PRE OUT |
|
|
|||
ASSIGNABLE |
IN 2 |
|
|
|
|
|
|
||||
IN 1 |
|
|
|
|
|
|
|
|
|
|
|
(DVD) |
|
(DVR/BDR) |
L |
|
|
|
|
|
|
|
|
Y |
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANTENNA
PB |
PB |
R |
|
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE |
SUBWOOFER |
|
|
PR |
PR |
OUT |
OUT |
IN |
IN |
IN |
IN |
IN |
OUT IN |
|
AM LOOP |
|
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
||
|
|
|
|
|
|
|
|
|
|||
|
MONITOR |
|
|
|
|
|
|
|
R |
L |
R |
|
|
|
|
|
|
|
|
|
|
|
|
Y |
OUT |
|
|
|
|
|
|
|
|
|
|
|
VIDEO |
|
|
|
|
|
|
|
|
|
|
PB |
|
|
|
|
IR |
CONTROL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
IN |
OUT |
IN OUT |
|
|
|
|
|
PR |
|
|
|
|
|
|
|
|
|
|
|
SPEAKERS A
PR |
PB |
Y |
|
R ANALOG L |
OPTICAL |
COMPONENT VIDEO IN |
VIDEO IN |
AUDIO OUT |
DIGITAL OUT |
||
|
Select one |
|
Select one |
This connection is required in order to
listen to the sound of the TV over the receiver.
TV
•Connect using an HDMI cable to listen to HD audio on the receiver. Do not use an HDMI cable to input video signals.
Depending on the video component, it may not be possible to output signals connected by HDMI and other methods simultaneously, and it may be necessary to make output settings.
Please refer to the operating instructions supplied with your component for more information.
28
En
Connecting your equipment
Satellite and cable receivers, and terrestrial digital TV tuners are all examples of so-called ‘set-top boxes’.
VSX-1020/VSX-1025
N 2 |
IN 3 |
IN 4 |
OUT |
LAN |
COAXIAL ASSIGNABLE |
|
|
OPTICAL |
|
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
IN 2 |
ASSIGNABLE |
|
|
|
|
|
|
|
|
ADAPTER POR |
|||
|
|
|
|
|
|
|
|
|
(OUTPUT 5 V |
100 mA MA |
|
|
|
|
|
(DVD) |
(CD) |
(TV/SAT) |
(DVR/BDR) |
|
PRE OUT
|
|
|
|
|
|
|
ANTENNA |
|
|
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE |
SUBWOOFER |
|
|
|
OUT |
IN |
IN |
IN |
IN |
IN |
OUT IN |
|
AM LOOP |
FM UNBAL 75 |
|
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
SURROU |
|
|
|
|
|
|
R |
L |
R |
L R |
IR CONTROL
IN OUT IN OUT
SPEAKERS A
|
R ANALOG L |
COAXIAL OPTICAL |
|
AUDIO OUT |
DIGITAL OUT |
VIDEO OUT |
Select one |
STB
•If the connection was made using a coaxial cable, you’ll need to tell the receiver which digital input you connected the set-top box to (see The Input Setup menu on page 42).
03
|
|
|
|
Connecting a HDD/DVD |
English |
||
recorder, VCR and other video |
|||
|
|||
sources |
|
||
This receiver has two sets of audio/video |
|
||
inputs and outputs suitable for connecting |
Deutsch |
||
analog or digital video devices, including |
|||
|
|||
HDD/DVD recorders and VCRs. |
|
||
VSX-1020/VSX-1025 |
|
||
|
|
|
IN 1 |
IN 2 |
IN 3 |
IN 4 |
OUT |
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
|
|
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
ASSIGNABLE |
|
|
|
|
|
|
|
|
|
IN 2 |
Français |
|
|
|
|
|
|
|
|
|
|
(OUTP |
|
|
|
|
|
|
|
(DVD |
|
(TV/SAT) |
(DVR/BDR) |
|
2 |
AUDIO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ANTENNA |
|
|
B |
|
|
|
|
|
|
|
|
|
|
ZONE 2 |
DVR/BDR |
DVD |
TV/SAT |
VIDEO |
CD |
CD-R/TAPE |
SUBWOOFER |
|
|
|
OUT |
OUT IN |
IN |
IN |
IN |
IN |
OUT |
IN |
|
AM LOOP |
|
R |
|
|
|
|
|
FRONT |
CENTER |
SURROUND |
|
|
|
|
|
|
|
|
|
||||
R |
|
|
|
|
R |
|
L |
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
DEO |
|
|
|
|
|
|
|
|
|
Italiano |
|
|
IR |
CONTROL |
|
|
|
|
|
||
|
IN |
OUT |
IN OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SPEAKERS A |
|
|
|
|
|
|
|
|
|
|
|
|
Nederlands |
|
|
|
|
|
R |
ANALOG |
L |
COAXIAL |
OPTICAL |
|
R ANALOG L |
|
|
|
|
|
AUDIO OUT |
DIGITAL OUT |
Español |
||
|
|
|
|
|
Select one |
|||||
AUDIO IN |
VIDEO IN |
VIDEO OUT |
|
|
||||||
|
|
|
HDD/DVD recorder, VCR, etc.
•If the connection was made using a coaxial cable, you’ll need to tell the receiver which digital input you connected the recorder to (see The Input Setup menu on page 42).
•In order to record, you must connect the analog audio cables (the digital connection is for playback only).
29
En
03 Connecting your equipment
This receiver has both digital and analog inputs, allowing you to connect audio components for playback.
One of these inputs have corresponding outputs for use with analog audio recorders.
VSX-1020/VSX-1025 |
|
|
|
|
|
|||
IN 4 |
OUT |
LAN |
COAXIAL ASSIGNABLE |
|
OPTICAL |
|
|
|
|
|
(10/100) |
IN 1 |
IN 2 |
IN 1 |
ASSIGNABLE |
ADAPTER PORT |
|
|
|
|
|
|
IN 2 |
|||
|
|
|
|
|
|
(OUTPUT 5 V |
100 mA MAX) |
|
|
|
|
(DVD) |
|
|
(DVR/BDR |
|
|
TV/SAT |
CD-R/TAPE |
|
|
|
|
|
||
IN |
|
OUT |
IN |
|
|
AM LOOP |
FM UNBAL 75 |
|
|
|
FRONT |
|
R |
SURROUND |
L |
SURROUND |
|
|
|
|
|
|
|
R |
||
CONTROL |
|
|
|
|
|
|
|
|
IN |
OUT |
|
|
|
|
|
|
|
|
|
|
|
|
SPEAKERS A |
|
|
•If your turntable has line-level outputs (i.e., it has a built-in phono pre-amp), connect it to the CD inputs instead.
•If you’re connecting a recorder, connect the analog audio outputs to the analog audio inputs on the recorder.
This unit has an on-board Windows Media™ Audio 9 Professional1 (WMA9 Pro) decoder, so it is possible to playback WMA9 Pro-encoded audio using HDMI, coaxial or optical digital connection when connected to a WMA9 Procompatible player. However, the connected DVD player, set-top box, etc. must be able to output WMA9 Pro format audio signals through a coaxial or optical digital output.
|
|
R ANALOG L |
COAXIAL OPTICAL |
R REC |
|
AUDIO OUT |
DIGITAL OUT |
L |
Select one |
||
AUDIO IN |
|
CD-R, MD, DAT, etc.
•If the connection was made using an optical cable, you’ll need to tell the receiver which digital input you connected the component to (see The Input Setup menu on page 42).
Note
1• Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
• With WMA9 Pro, sound problems may occur depending on your computer system. Note that WMA9 Pro 96 kHz sources will be downsampled to 48 kHz.
30
En