INSTALLATION MANUAL
AVIC-D2
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.
MANUEL |
Français English |
D’INSTALLATION |
|
IMPORTANT INFORMATION
ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL
•The navigation features of this product (and rear view camera option if purchased) is intended solely as an aid to you in the operation of your vehicle. It is not a substitute for your attentiveness, judgment and care when driving.
•Never use this navigation system to route to hospitals, police stations, or similar facilities in an emergency, Please call 911.
•Do not operate this navigation system (or the rear view camera option if purchased) if doing so in any way will divert your attention from the safe operation of your vehicle. Traffic restrictions and advisories currently in force should always take precedence over guidance given by this product. Always obey current traffic restrictions, even if this product provides contrary advice.
•Certain government laws may restrict the placement and use of navigation systems in your vehicle. Please comply with all applicable laws and regulations in the installation and operation of your navigation system.
•This manual explains how to install this navigation system in your vehicle. Operation of this navigation system is explained in the separate Operation Manual or Hardware Manual for the navigation system.
•Do not install this product where it may (i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems of safety features, including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely operate the vehicle. In some cases, it may not be possible to install this product because of the vehicle type or the shape of the vehicle interior.
1
Contents |
|
IMPORTANT INFORMATION .................... |
1 |
ABOUT YOUR NEW NAVIGATION |
|
SYSTEM AND THIS MANUAL .............. |
1 |
IMPORTANT SAFEGUARDS .................... |
3 |
PLEASE READ ALL OF THESE |
|
INSTRUCTIONS REGARDING |
|
YOUR NAVIGATION |
|
SYSTEM AND RETAIN THEM |
|
FOR FUTURE REFERENCE .................... |
3 |
Connecting the System ............................ |
4 |
- Before installing this product |
|
- To prevent damage |
|
- Parts supplied |
|
Connecting the system ...................................... |
7 |
Connecting the power cord (1) .......................... |
9 |
Connecting the power cord (2) ........................ |
11 |
When connecting to separately sold power |
|
amp .......................................................... |
13 |
When connecting a Rear view camera ............ |
15 |
When connecting the external video component |
|
and the display .......................................... |
16 |
-When using a display connected to rear video output
Installation ................................................ |
17 |
To guard against electromagnetic |
|
interference .............................................. |
18 |
Before installing .............................................. |
18 |
Installing this product ...................................... |
19 |
- Installation notes |
|
- Parts supplied |
|
- DIN Front/Rear-mount |
|
- DIN Front-mount |
|
- DIN Rear-mount |
|
Installing the GPS antenna .............................. |
23 |
-Installation notes
-Parts supplied
-When installing the antenna inside the vehicle (on the rear shelf)
-When installing the antenna outside the vehicle (on the body)
After Installing this Product.................... |
26 |
English
Español
Italiano Français Deutsch
Nederlands
2
IMPORTANT SAFEGUARDS
PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE
1.Read this manual fully and carefully before installing your navigation system.
2.Keep this manual handy for future reference.
3.Pay close attention to all warnings in this manual and follow the instructions carefully.
4.This navigation system may in certain circumstances display erroneous information regarding the position of your vehicle, the distance of objects shown on the screen, and compass directions. In addition, the system has certain limitations, including the inability to identify one-way streets, temporary traffic restrictions and potentially unsafe driving areas. Please exercise your own judgment in the light of actual driving conditions.
5.As with any accessory in your vehicle’s interior, the navigation system should not divert your attention from the safe operation of your vehicle. If you experience difficulty in operating the system or reading the display, please make adjustments while safely parked.
6.Please remember to wear your seat belt at all times while operating your vehicle. If you are ever in an accident, your injuries can be considerably more severe if your seat belt is not properly buckled.
Do not attempt to install or service your navigation system by yourself. Installation or servicing of the navigation system by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock or other hazards.
3
Connecting the System
|
|
|
|
|
• |
Pioneer does not recommend that you install your navigation system yourself. We |
|
||
|
recommend that only authorized Pioneer service personnel, who have special train- |
|
||
|
ing and experience in mobile electronics, set up and install this product. NEVER |
English |
||
|
SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and |
|||
|
|
|||
|
its connecting cables may expose you to the risk of electric shock or other hazards, |
|
||
|
and can cause damage to the navigation system that is not covered by warranty. |
|
||
|
|
|
|
|
|
|
|
|
|
• |
If you decide to perform the installation yourself, and have special training and |
|
||
|
experience in the mobile electronics installations, please carefully follow all of the |
Español |
||
|
steps in the Installation Manual. |
|||
|
|
|||
• |
Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring |
|
||
|
to remain exposed. |
|
||
• Do not directly connect the yellow lead of this product to the vehicle battery. If the |
|
|||
|
lead is directly connected to the battery, engine vibration may eventually cause the |
|
||
|
insulation to fail at the point where the wire passes from the passenger compart- |
|
||
|
ment into the engine compartment. If the yellow lead’s insulation tears as a result |
Deutsch |
||
|
of contact with metal parts, short-circuiting can occur, resulting in considerable |
|||
|
|
|||
|
danger. |
|
||
• |
It is extremely dangerous to allow the GPS antenna cable to become wound around |
|
||
|
the steering column or shift lever. Be sure to install this product, its cables, and |
|
||
|
wiring away in such a way that they will not obstruct or hinder driving. |
|
||
• |
Make sure that the cables and wires are routed and secured so they will not inter- |
|
||
|
fere with or become caught in any of the vehicle’s moving parts, especially the |
|
||
|
steering wheel, shift lever, parking brake, sliding seat tracks, doors, or any of the |
Français |
||
|
tion heats up, wires may become damaged, resulting in a short circuit or malfunc- |
|||
|
vehicle’s controls. |
|
||
• |
Do not route wires where they will be exposed to high temperatures. If the insula- |
|
||
|
tion and permanent damage to this product. |
|
||
• |
Do not cut the GPS antenna cable to shorten it or use an extension to make it |
|
||
|
longer. Altering the antenna cable could result in a short circuit or malfunction. |
|
||
• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resister |
Italiano |
|||
|
power supply lead of the navigation system and tapping into the lead. The current |
|||
|
or filter, etc.) may fail to work properly. |
|
||
• |
Never feed power to other electronic products by cutting the insulation of the |
|
||
|
capacity of the lead will be exceeded, causing overheating. |
|
||
• |
The black lead is ground. Please ground this lead separately from the ground of |
|
||
|
high-current products such as power amps. |
|
||
|
Do not ground more than one product together with the ground from another |
Nederlands |
||
|
product. For example, you must separately ground any amplifier unit away from |
|||
|
|
the ground of this product. Connecting grounds together can cause a fire and/or damage the products if their grounds became detached.
4
Connecting the System
Before installing this product
•This product is for vehicles with a 12-volt battery and negative grounding. Check the battery voltage of your vehicle before installation.
• To avoid shorts in the electrical system, be sure to disconnect the (–) battery cable before beginning installation.
To prevent damage
When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.
•When disconnecting a connector, pull the connector itself. Do not pull the lead, as you may pull it out of the connector.
•This product cannot be installed in a vehicle that does not have an ACC (accessory) position on the ignition switch.
O
FF
AC
C
O
N |
||
|
|
S |
|
|
T |
|
R |
A |
T |
|
O
FF
O
N |
||
|
|
S |
|
|
T |
|
R |
A |
T |
|
ACC position |
No ACC position |
•When connecting the blue lead to the auto antenna and using the auto antenna function, the vehicle’s antenna can be stowed by following the instructions below.
–In the INITIAL menu, select “RADIO” for “AUTO ANTENNA” and change the source from radio to another source
–Turn the source off
–Turn off the ignition switch (ACC OFF)
For more detailed information on changing the “AUTO ANTENNA” mode, refer to “Switching the auto antenna setting” in the Operation Manual.
•To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especially important to insulate all unused speaker leads, which if left uncovered may cause a short circuit.
•Attach the connectors of the same color to the corresponding colored port, i.e., blue connector to the blue port, black to black, etc.
•Refer to the owner’s manual for details on connecting the power amp and other units, then make connections accordingly.
•Since a unique BPTL circuit is employed, do not directly ground the ≠ side of the speaker lead or connect the ≠ sides of the speaker leads together. Be sure to connect the ≠ side of the speaker lead to the ≠ side of the speaker lead on this product.
•If the RCA pin jack on this product will not be used, do not remove the caps attached to the end of the connector.
5
•Never connect speakers with an output rating of less than 50 W channel or impedance outside of the 4 ohms to 8 ohms specifications to your navigation system. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged.
•When the ignition switch is turned on (ACC ON), a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control terminal (max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even if the audio source is switched off.
•When an external power amp is being used with this system, be sure not to connect the blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the power terminal of the auto antenna. Such connection could cause excessive current drain and malfunction as well as damage to the auto antenna of the vehicle.
Parts supplied
This product |
Power cord |
Connector |
Extension lead |
Extension lead |
GPS antenna |
(for reverse signal) |
(for speed signal) |
|
RCA connector
English
Español
Italiano Français Deutsch
Nederlands
6
Connecting the System
Connecting the system
WIRED REMOTE IN |
|
|
Please see the Instruction Manual for |
RCA connector |
|
the Wired Remote Control Adapters (sold separately). |
||
See Page 13 to 16. |
Power cord
See Page 9 to 12.
Black
|
This product |
|
Antenna jack |
|
|
Black |
|
|
Blue |
Light gray |
|
Blue |
||
|
||
|
5 m (16 ft. 5 in.) |
|
|
GPS antenna |
IP-BUS cable
(supplied with XM tuner)
XM DATA cable (supplied with XM tuner)
•When combining this product with GEX-P10XMT (sold separately), this connection must be required.
•When installing the XM tuner in the trunk, etc.,
the optional cable (e.g. CD-600DC) (sold separately) is required.
Note:
The XM tuner will not receive XM Radio service when you drive outside of the XM’s coverage area. When the XM tuner is not used, connect the IP-BUS cable*1 directly to this product*2.
Hide-away XM tuner (GEX-P10XMT) (sold separately)
|
Black |
Black |
Blue |
*1
7
•To avoid the risk of accident and the potential violation of applicable laws, this product should never be used while the vehicle is being driven except for navigation purposes. And, also Rear Displays should not be in a location where it is a visible distraction to the driver.
•In some countries or states the viewing of images on a display inside a vehicle, even by persons other than the driver, may be illegal. Where such regulations apply, they must be obeyed, and this product’s rear video output features should not be used.
English
Español
Deutsch
AV-BUS cable |
Black |
|
|
(supplied with TV tuner) |
|
|
Hide-away TV tuner |
|
(e.g. GEX-P5700TV) |
|
(sold separately) |
Blue |
|
Multi-CD player |
Black |
|
|
(sold separately) |
|
IP-BUS cable |
|
IP-BUS cable
(supplied with TV tuner)
Italiano Français
Nederlands
8
Connecting the System
Connecting the power cord (1)
Fuse (10 A) |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Yellow |
|
|
|
|
|
||||
To terminal always supplied |
|
|
|
|
|
||||
with power regardless of |
|
|
|
|
|
||||
ignition switch position. |
|
|
|
|
|
||||
Red |
Fuse resistor |
||||||||
|
|
|
|
|
|||||
To electric terminal controlled |
|
|
|
|
|
||||
by ignition switch (12 V DC) |
|
|
|
|
|
||||
ON/OFF. |
|
|
|
|
|
||||
Orange/white |
Fuse resistor |
||||||||
To lighting switch terminal. |
|
|
|
|
|
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
|
|
|
White |
Gray |
|
|
|
Front speaker |
+ |
+ |
|
|
Front speaker |
||
|
|
≠ |
|
|
|
||
|
|
|
≠ |
|
|
||
Left |
|
|
White/black |
Gray/black |
|
Right |
|
|
|
Green |
Violet |
|
|||
|
|
|
|
|
|||
Rear speaker |
|
+ |
+ |
|
|
Rear speaker |
|
|
|
||||||
or Subwoofer |
|
|
≠ |
|
|
|
or Subwoofer |
|
|
≠ |
|||||
|
|
|
|
|
|||
|
|
|
Green/black |
Violet/black |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note: |
|
|
|
|
|
|
|
When a subwoofer is connected to this product instead |
|
|
||
|
|
|
of a rear speaker, change the rear output setting in |
|
|
||
|
|
|
the Initial Setting. (Refer to the Operation Manual.) |
|
|
||
|
|
|
The subwoofer output of this product is monaural. |
|
|
||
|
|
|
|
|
|
|
|
9
This product
Note:
Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function.
Yellow/black
If you use equipment with a mute function (e.g. cellular telephones), connect that equipment to the Audio Mute lead. If not, keep the Audio Mute lead free of any connections.
Note:
Audio source will be set to mute or attenuate, while the voice guidance of the navigation will not be muted or attenuated. For details, see the Operation Manual.
Note:
When connecting the blue lead to the auto antenna and using the auto antenna function, the vehicle’s antenna can be stowed by following the instructions below.
-In the INITIAL menu, select “RADIO” for “AUTO ANTENNA” and change the source from radio to another source
-Turn the source off
-Turn off the ignition switch (ACC OFF)
For more detailed information on changing the “AUTO ANTENNA” mode, refer to “Switching the auto antenna setting” in the Operation Manual.
Blue
To Auto-antenna relay control terminal.
If the vehicle has a glass antenna, connect to the antenna booster power supply terminal (max. 300 mA 12 V DC).
For information on other leadsSee Page 11.
English
Español
Italiano Français Deutsch
Nederlands
10
Connecting the System
Connecting the power cord (2)
Speed detection circuit lead
Vehicle injection Connector computer
Connection method
Pass the extension cord and the lead for the speed detection circuit through this hole.
Clamp firmly with needlenosed pliers.
Close the cover.
Light green
Pink (CAR SPEED SIGNAL INPUT)
The mobile navigation system is connected here to detect the distance the vehicle travels. Always connect the vehicle’s speed detection circuit or the ND-PG1 speed pulse generator, sold separately. Failure to make this connection will increase errors in the location display.
IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE VEHICLE’S ANTILOCK BRAKING SYSTEM, AUTOMATIC TRANSMISSION AND SPEEDOMETER INDICATION.
•It is strongly suggested that the speed pulse wire be connected for accuracy of navigation and better performance of interlock.
•If the speed pulse wire is unavailable for some reason, it is recommended that the pulse generator (ND-PG1) be used.
Notes:
•The position of the speed detection circuit and the position of the parking brake switch vary depending on the vehicle model. For details, consult your authorized Pioneer dealer or an installation professional.
•Even when the light green lead and the pink lead are connected correctly, a message indicating improper connection is shown until sensor initialization has completed.
Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch. If this connection is made incorrectly or omitted, certain functions of your navigation system will be unusable.
LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Connection method
Clamp the parking brake switch power supply side lead.
Clamp firmly with needle-nosed pliers.
Power supply side
Ground side
Parking brake switch
11
Extension lead (for speed signal) 5 m (16 ft. 5 in.)
This product
Note:
Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another
product, refer to the supplied manuals of both prod-
ucts and connect cords that have the same function. Power cord
For information on other leadsSee Page 9.
Violet/white (REVERSEGEAR SIGNAL INPUT)
This is connected so that the navigation system can detect whether the vehicle is moving forwards or backwards. Connect the violet/white lead to the lead whose voltage changes when the shift lever is put in reverse. Unless connected, the sensor may not detect your vehicle traveling forward/backward properly, and thus the position of your vehicle detected by the sensor may be misaligned from the actual position.
Note: When you use the ND-PG1 speed pulse generator (sold separately), please make sure to connect this lead.
When you use a rear view camera, please make sure to connect this lead. Otherwise you cannot switch to rear view camera picture.
See Page 15.
Be sure to use only the supplied extension lead. Use of another lead could cause fire, smoke and/or damage this product.
Fuse resistor
Extension lead
5 m (16 ft. 5 in.)
(for reverse signal)
Check the position of your vehicle’s reversing lamp (the one that lights up when the shift lever is in reverse [R]) and find the reversing lamp lead in the trunk.
Connection method
Clamp the reversing lamp lead.
Clamp firmly with needle-nosed pliers.
Reversing lamp lead
English
Español
Italiano Français Deutsch
Nederlands
12
Connecting the System
When connecting to separately sold power amp
For information on other cablesSee Page 15 to 16.
This product
Subwoofer output or non-fading output
(SUBWOOFER OUTPUT or NON-FANDING OUTPUT)
23 cm (9 in.)
Rear output (REAR OUTPUT)
15 cm (5–7/8 in.)
Front output (FRONT OUTPUT)
15 cm (5–7/8 in.)
Blue/white
To system control terminal of the power amp (max. 300 mA 12 V DC).
Do not connect this lead to Auto-antenna control terminal.
13
Perform these connections when using the optional amplifier.
Power amp (sold separately)
RCA cables (sold separately)
Power amp (sold separately)
Power amp (sold separately)
System remote control |
|
Left |
Right |
+ |
+ |
Front speaker |
Front speaker |
≠ |
≠ |
+ |
+ |
Rear speaker |
Rear speaker |
≠ |
≠ |
+ |
+ |
Subwoofer |
Subwoofer |
≠ |
≠ |
Note:
You can change the RCA output of the subwoofer depending on your subwoofer system. (Refer to the Operation Manual.)
English
Español
Italiano Français Deutsch
Nederlands
14
Connecting the System
When connecting a Rear view camera
When using this product with a rear view camera, automatic switching to video from a rear view camera is possible when the gear shift is moved to REVERSE (R) position.
Rear view mode also allows you to check what is behind you while driving.
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
•The screen image may appear reversed.
•The rear view camera function is to use this product as an aid to keep an eye on trailers, or backing into a tight parking spot. Do not use this function for entertainment purposes.
•The object in rear view may appear closer or more distant than in reality.
•Please note that the edges of the rear view camera images may differ slightly according to whether full screen images are displayed when backing, and whether the images are used for checking the rear when the vehicle is moving forward.
|
15 cm (5 - 7/8 in.) |
|
5 m (16 ft. 5 in.) |
|
|
|
Brawn |
|
|
(REAR VIEW CAMERA IN) |
|
Violet/white |
|
|
Brown |
Note: |
|
It is necessary to set to “CAMERA” |
||
|
||
|
in “SETUP” when connecting the |
|
|
rear view camera. (For details, see the |
|
|
Operation Manual) |
This product
Extension lead (for reverse signal)
Fuse resistor
About connection method See Page 11.
RCA cable
(sold separately)
Rear view
camera
To video output
Note:
Connect to the rear view camera. Do not connect to any other equipment.
Be sure to use only the supplied extension lead. Use of another lead could cause fire, smoke and/or damage this product.
15
When connecting the external video component and the display
This product
For information on other cablesSee Page 13 to 15.
15 cm (5 - 7/8 in.)
Yellow
(REAR MONITOR OUTPUT)
RCA cables (sold separately)
Note:
The map screen navigation images output to the rear display differ from standard NTSC format images. Therefore, their quality will be inferior to the images that appear on the front display.
20 cm (7 - 7/8 in.)
Yellow
(VIDEO INPUT) Red, white (AUDIO INPUT)
To audio outputs
External video component (sold separately)
To video output
RCA cables (sold separately)
To video input
Display with RCA input jacks
•It is necessary to set to “AV INPUT” or “REAR DISP” in “SET UP” when connecting the external video component.
When using a display connected to rear video output
This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the video source.
•NEVER install the rear display in a location that enables the driver to watch the video source while Driving.
English
Español
Italiano Français Deutsch
Nederlands
16