NAIS HP2-AC48V, HP2-AC6V, HP2-DC110V, HP2-DC12V, HP2-DC48V Datasheet

VDE

2c, 3c

10 AMP POWER RELAY HP-RELAYS

25

.984 36

1.417

44.5

1.752

FEATURES

•Interchangeable with existing models

•Long life and high reliability

•High contact capacity up to 10 A 250 V AC

•Available with plug-in/solder and quick-connect terminals

mm inch

SPECIFICATIONS (at 20°C 68°F)

Contacts

Arrangement			2 Form C	3 Form C	4 Form C
Initial contact resistance, max.				15 mΩ
(By voltage drop 6 V DC 1 A)
Contact	material		Silver			Silver
						alloy
Rating		Nominal switching	10 A 250 V AC (resistive)
		capacity
Remarks
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as "initial breakdown voltage" section
*2 Detection current; 10 mA
*3 Excluding contact bounce time
*4 Half-wave pulse of sine wave: 11ms; detection time: 10 s
*5 Half-wave pulse of sine wave: 6ms
*6 Detection time: 10 s
*7 Refer to	5. Conditions for operation, transport and storage mentioned in

AMBIENT ENVIRONMENT (Page 61).

Characteristics (at 60 Hz, 20°C 68°F)

					2 Form C	3 Form C	4 Form C
	Maximum operating speed					20 cpm
	Initial insulation resistance*1				more than 100 MΩ at 500 V DC
			Between open		1,000	2,000	1,000
			contacts		Vrms	Vrms	Vrms
	Breakdown		Between contact sets		1,500	2,000	1,500
	voltage*2				Vrms	Vrms	Vrms
			Between contact and		1,500	2,000	1,500
			coil		Vrms	Vrms	Vrms
	Operate time*3 (at nominal voltage)				Approx.	Approx. 25		ms
					15 ms
	Release time (without diode)*3				Approx.	Approx. 25		ms
	(at nominal voltage)				15 ms
	Temperature rise					Max. 65°C
	Shock resistance			Functional*4	98	m/s2 {10 G}
				Destructive*5	980	m/s2 {100 G}
				Functional*6	58.8 m/s2 {6 G}, 10 to 55 Hz
					at 1 mm double amplitude
	Vibration resistance
				Destructive	117.6 m/s2 {12 G}, 10 to 55 Hz
					at 2 mm double amplitude
	Conditions for opera-			Ambient	–50°C to +40°C
	tion, transport and			temp.	–58°F to +104°F
	storage*7
	(Not freezing and
	condensing at low			Humidity	5 to 85% R.H.
	temperature)
					Approx.	Approx.	Approx.
	Unit weight				60g	100g	125g
					2.12 oz	3.53 oz	4.41 oz

LIFE DATA

Contact rating and expected life For AC load type

	Voltage		125 V AC			250 V AC		Expected life
	Load	Resistive (cos ϕ ] 1)		Inductive (cos ϕ ] 0.4)		Resistive (cos ϕ ] 1)	Inductive (cos ϕ ] 0.4)	(min. operations)
Electrical		—		—		10 A	7.5 A	2×105
		10 A		7.5 A		7.5 A	5 A	5×105
life	Current
		5 A		3 A		3 A	2 A	1×106
		1A		0.7 A		0.6 A	0.4 A	2×106
				Mechanical	life			1×107
Note: When the electromagnet or exciting coil (Solenoid, etc.) is the					load, the value of motor or lamp load is applicable.

411

HP

Contact rating and expected life For DC load type

	Voltage		24 V DC		125 V DC		Expected life
	Load	Resistive (cos ϕ ] 1)		Inductive (cos ϕ ] 0.4)	Resistive (cosϕ ] 1)	Inductive (cos ϕ ] 0.4)	(min. operations)
Electrical		—		7 A	—	—	2×105
		7.5 A		5 A	0.5 A	0.4 A	5×105
life	Current
		5 A		3 A	0.3 A	0.2 A	1×106
		1A		0.6 A	0.1 A	0.06 A	2×106
				Mechanical life			1×107

Life curve
1,000			Mechanical life
	900		more than 10,000,000
4			operations
×10	800
Operations,
	500
	700
	600
	400
	300
	200	2	125 V	AC		cos		ϕ	= 1
		5
	100	0	V
			A
			C
	0		cosϕ		= 1
			5							10
							Load current, A

Notes:

1.For DC inductive loads, use an arc suppressing circuit.

2.When used under a DC load operating at high repetition rate with considerable arcing, corrosion of the contacts and/or the contact blades is likely to occur. When using the relay under conditions of high temperature, humidity or high repetition rate, it is suggested that the relay cover be removed to facilitate extended operation.

TYPICAL APPLICATIONS

HP relays enjoy wide use in various appli-	Machine tool	Transportation
cations, particularly in automation con-	Food processing packing machines	Communication and measuring devices
trols and remote controls.	Office equipment	Amusement devices
Applications include:	Coin operate devices
Industrial machinery	Home appliances

ORDERING INFORMATION

Ex.

HP

3

M

AC240V

Contact arrangement

Terminal

Coil voltage

2: 2 Form C

Nil: Standard plug-in terminal

AC 6, 12, 24, 48,

3: 3 Form C

M: Direct mounting (3 Form C only)

115, 220, 240 V

4: 4 Form C

TM: Top mounting (2 Form C only)

DC 6, 12, 24, 48,

L: Lamp wired, standard plug-in terminal

110 V

(Notes) 1. For UL/CSA or VDE recognized types, add suffix UL/CSA or VDE (HP2-TM type VDE application under way)

2.Standard packing Carton: 50 pcs. Case: 200 pcs.

3.UL/CSA approved type is standard.

TYPES AND COIL DATA

1. Standard plug-in terminal type (without lamp wired)

DC TYPES at 20°C 68°F

			Nominal coil	Pick-up	Drop-out	Max.	Coil	Nominal coil	Nominal
	Type	Part No.		voltage,	voltage,	allowable	resistance,		operating
			voltage, V DC					current, mA
				V DC (max.)	V DC (min.)	voltage, V DC	Ω (±10%)		power, W
		HP2-DC6V	6	4.8	0.9	6.6	25	240	1.5
		HP2-DC12V	12	9.6	1.8	13.2	110	109	1.3
	2 Form C	HP2-DC24V	24	19.2	3.6	26.4	440	54.5	1.3
		HP2-DC48V	48	38.4	7.2	52.8	1,800	26.7	1.3
		HP2-DC110V	110	88	16.5	121	7,300	15.0	1.7
		HP3-DC6V	6	4.8	0.9	6.6	24	250	1.5
		HP3-DC12V	12	9.6	1.8	13.2	100	120	1.4
	3 Form C	HP3-DC24V	24	19.2	3.6	26.4	400	60	1.4
		HP3-DC48V	48	38.4	7.2	52.8	1,560	31	1.5
		HP3-DC110V	110	88	16.5	121	7,450	14.9	1.6
		HP4-DC6V	6	4.8	0.9	6.6	22	273	1.6
		HP4-DC12V	12	9.6	1.8	13.2	95	127	1.5
	4 Form C	HP4-DC24V	24	19.2	3.6	26.4	380	63	1.5
		HP4-DC48V	48	38.4	7.2	52.8	1,500	32	1.5
		HP4-DC110V	110	88	16.5	121	7,000	15.7	1.7

412

										HP
	AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F
			Nominal coil		Pick-up	Drop-out	Max.	Inductance,	Nominal coil	Nominal
	Type	Part No.			voltage,	voltage,	allowable			operating
			voltage, V	AC				H	current, mA
					V AC (max.)	V AC (min.)	voltage, V AC			power, VA
		HP2-AC6V	6		4.8	1.8	6.6	0.049	310	1.9
		HP2-AC12V	12		9.6	3.6	13.2	0.190	160	1.9
		HP2-AC24V	24		19.2	7.2	26.4	0.776	78	1.9
	2 Form C	HP2-AC48V	48		38.4	14.4	52.8	3.106	39	1.9
		HP2-AC115V	115		92	34.5	126.5	15.83	18	2.1
		HP2-AC220V	220		176	66	242	57.90	9.5	2.1
		HP2-AC240V	240		192	72	264	66.26	9.0	2.2
		HP3-AC6V	6		4.8	1.8	6.6	0.030	520	3.1
		HP3-AC12V	12		9.6	3.6	13.2	0.119	260	3.1
		HP3-AC24V	24		19.2	7.2	26.4	0.475	130	3.1
	3 Form C	HP3-AC48V	48		38.4	14.4	52.8	1.899	65	3.1
		HP3-AC115V	115		92	34.5	126.5	10.36	28.5	3.3
		HP3-AC220V	220		176	66	242	39.32	14.2	3.1
		HP3-AC240V	240		192	72	264	44.05	13.9	3.3
		HP4-AC6V	6		4.8	1.8	6.6	0.019	800	4.8
		HP4-AC12V	12		9.6	3.6	13.2	0.077	400	4.8
		HP4-AC24V	24		19.2	7.2	26.4	0.309	200	4.8
	4 Form C	HP4-AC48V	48		38.4	14.4	52.8	1.292	95	4.6
		HP4-AC115V	115		92	34.5	126.5	6.953	42	4.8
		HP4-AC220V	220		176	66	242	26.57	21	4.6
		HP4-AC240V	240		192	72	264	29.75	20.5	4.9

NOTES

1.The range of coil current for AC relays is ±15% (60 Hz). For DC relays it is

±10% at 20°C, 68°F.

2.The HP relay will operate in a range from 80% to 110% of the nominal coil voltage. It is, however, recommended that the relay be used in the range of 85% to 110% of the nominal coil voltage, with the temporary voltage variation taken into consideration.

3.When the operating voltage of AC re-

lays drops below 80% of the nominal coil voltage, the relay will generate a considerable amount of heat which is not recommended for maximum efficiency.

4.The coil resistance of DC types is the

measured value of the coil at a temperature of 20°C 68°F. If the coil temperature changes by ±1°C, the measured value of the coil resistance should be increased or decreased by 0.4%.

5.For applications from 220 V to 240 V DC, connect a resistor in series with the relay coil. See chart for resistor values.

	Voltage	2 Form C	3 Form C	4 Form C
	220 V DC	7.3 kΩ	7.45 kΩ	7 kΩ
		(5 W)	(5 W)	(5 W)
	240 V DC	8.7 kΩ	8.8 kΩ	8.3 kΩ
		(5 W)	(5 W)	(5 W)

2. Standard plug-in terminal type (with lamp wired)

DC TYPES at 20°C 68°F

				Nominal coil	Pick-up	Drop-out	Max.	Coil	Nominal coil	Nominal
							allowable			operating
	Type		Part No.	voltage,	voltage,	voltage,		resistance,	current,
							voltage,			power,
				V DC	V DC (max.)	V DC (min.)		Ω (±10%)	mA
							V DC			W
			HP2-L-DC6V	6	4.8	0.9	6.6	25	240	1.5
		LED	HP2-L-DC12V	12	9.6	1.8	13.2	110	109	1.3
	2 Form C		HP2-L-DC24V	24	19.2	3.6	26.4	440	54.5	1.3
			HP2-L-DC48V	48	38.4	7.2	52.8	1,800	26.7	1.3
		Neon lamp	HP2-L-DC110V	110	88	16.5	121	7,300	15.0	1.7
			HP3-L-DC6V	6	4.8	0.9	6.6	24	250	1.5
		LED	HP3-L-DC12V	12	9.6	1.8	13.2	100	120	1.4
	3 Form C		HP3-L-DC24V	24	19.2	3.6	26.4	400	60	1.4
			HP3-L-DC48V	48	38.4	7.2	52.8	1,560	31	1.5
		Neon lamp	HP3-L-DC110V	110	88	16.5	121	7,450	14.9	1.6
			HP4-L-DC6V	6	4.8	0.9	6.6	22	273	1.6
		LED	HP4-L-DC12V	12	9.6	1.8	13.2	95	127	1.5
	4 Form C		HP4-L-DC24V	24	19.2	3.6	26.4	380	63	1.5
			HP4-L-DC48V	48	38.4	7.2	52.8	1,500	32	1.5
		Neon lamp	HP4-L-DC110V	110	88	16.5	121	7,000	15.7	1.7

413

HP

AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F

				Nominal coil	Pick-up	Drop-out	Max.		Nominal coil	Nominal
							allowable	Inductance,		operating
	Type		Part No.	voltage,	voltage,	voltage,			current,
							voltage,	H		power,
				V AC	V AC (max.)	V AC (min.)			mA
							V AC			VA
			HP2-L-AC6V	6	4.8	1.8	6.6	0.049	310	1.9
		LED	HP2-L-AC12V	12	9.6	3.6	13.2	0.190	160	1.9
	2 Form C		HP2-L-AC24V	24	19.2	7.2	26.4	0.776	78	1.9
			HP2-L-AC115V	115	92	34.5	126.5	15.83	18	2.1
		Neon lamp	HP2-L-AC220V	220	176	66	242	57.90	9.5	2.1
			HP2-L-AC240V	240	192	72	264	66.26	9.0	2.2
			HP3-L-AC6V	6	4.8	1.8	6.6	0.030	520	3.1
		LED	HP3-L-AC12V	12	9.6	3.6	13.2	0.119	260	3.1
	3 Form C		HP3-L-AC24V	24	19.2	7.2	26.4	0.475	130	3.1
			HP3-L-AC115V	115	92	34.5	126.5	10.36	28.5	3.3
		Neon lamp	HP3-L-AC220V	220	176	66	242	39.32	14.2	3.1
			HP3-L-AC240V	240	192	72	264	44.05	13.9	3.3
			HP4-L-AC6V	6	4.8	1.8	6.6	0.019	800	4.8
		LED	HP4-L-AC12V	12	9.6	3.6	13.2	0.077	400	4.8
	4 Form C		HP4-L-AC24V	24	19.2	7.2	26.4	0.309	200	4.8
			HP4-L-AC115V	115	92	34.5	126.5	6.953	42	4.8
		Neon lamp	HP4-L-AC220V	220	176	66	242	26.57	21	4.6
			HP4-L-AC240V	240	192	72	264	29.75	20.5	4.9

3. Top Mounting (TM) and direct mounting (M) type

DC TYPES at 20°C 68°F

			Nominal coil	Pick-up	Drop-out	Max.	Coil	Nominal coil	Nominal
						allowable			operating
	Type	Part No.	voltage,	voltage,	voltage,		resistance,	current,
						voltage,			power,
			V DC	V DC (max.)	V DC (min.)		Ω (±10%)	mA
						V DC			W
		HP2-TM-DC6V	6	4.8	0.9	6.6	25	240	1.5
	2 Form C	HP2-TM-DC12V	12	9.6	1.8	13.2	110	109	1.3
		HP2-TM-DC24V	24	19.2	3.6	26.4	440	54.5	1.3
	Top Mounting Type (TM)
		HP2-TM-DC48V	48	38.4	7.2	52.8	1,800	26.7	1.3
		HP2-TM-DC110V	110	88	16.5	121	7,300	15.0	1.7
		HP3-M-DC6V	6	4.8	0.9	6.6	24	250	1.5
	3 Form C	HP3-M-DC12V	12	9.6	1.8	13.2	100	120	1.4
		HP3-M-DC24V	24	19.2	3.6	26.4	400	60	1.4
	Direct Mounting Type (TM)
		HP3-M-DC48V	48	38.4	7.2	52.8	1$B!"(J560	31	1.5
		HP3-M-DC110V	110	88	16.5	121	7,450	14.9	1.6
	AC TYPE (50/60 Hz) at 60 Hz, 20°C 68°F
			Nominal coil	Pick-up	Drop-out	Max.		Nominal coil	Nominal
						allowable	Inductance,		operating
	Type	Part No.	voltage,	voltage,	voltage,			current,
						voltage,	H		power,
			V AC	V AC (max.)	V AC (min.)			mA
						V AC			VA
		HP2-TM-AC6V	6	4.8	1.8	6.6	0.049	310	1.9
		HP2-TM-AC12V	12	9.6	3.6	13.2	0.190	160	1.9
	2 Form C	HP2-TM-AC24V	24	19.2	7.2	26.4	0.776	78	1.9
		HP2-TM-AC48V	48	38.4	14.4	52.8	3.106	39	1.9
	Top Mounting Type (TM)
		HP2-TM-AC115V	115	92	34.5	126.5	15.83	18	2.1
		HP2-TM-AC220V	220	176	66	242	57.90	9.5	2.1
		HP2-TM-AC240V	240	192	72	264	66.26	9.0	2.2
		HP3-M-AC6V	6	4.8	1.8	6.6	0.030	520	3.1
		HP3-M-AC12V	12	9.6	3.6	13.2	0.119	260	3.1
	3 Form C	HP3-M-AC24V	24	19.2	7.2	26.4	0.475	130	3.1
		HP3-M-AC48V	48	38.4	14.4	52.8	1.899	65	3.1
	Direct Mounting Type (M)
		HP3-M-AC115V	115	92	34.5	126.5	10.36	28.5	3.3
		HP3-M-AC220V	220	176	66	242	39.32	14.2	3.1
		HP3-M-AC240V	240	192	72	264	44.05	13.9	3.3

414