NAIS TQ4H-L2-4.5V, TQ4H-L2-3V, TQ4H-L2-24V, TQ4H-L2-12V, TQ4H-L-9V Datasheet

TESTING

LOW PROFILE

2 FORM C RELAY TQ-RELAYS

9

.354

26.7	5+0.4–0.2
1.051	.197+–.008.016		9
		14	.354
		.551

5+0–0..42

.197+–..016008

mm inch

FEATURES

• High sensitivity:

2 Form C: 140 mW power consumption (single side stable type) 4 Form C: 280 mW power consumption (single side stable type)

•Surge voltage withstand: 1500 V FCC Part 68

•Sealed construction allows automatic washing

•Self-clinching terminal also available

•M.B.B. contact types available

SPECIFICATIONS

Contact

			Standard				M.B.B.type
			(B.B.M) type
Arrangement			2 Form C		4 Form C		2 Form D
Initial contact resistance, max.					50 mΩ
(By voltage drop 6 V DC 1A)
Contact material				Gold-clad silver
	Nominal switching capacity		1 A 30 V DC				1 A 30 V
	(resistive load)		0.5 A 125 V AC				DC
	Max. switching power		30 W, 62.5 V A				30 W
Rating	(resistive load)
	Max. switching voltage		110 V DC, 125 V AC				110 V DC
	Max. switching current				1 A
	Min. switching capacity 1		10 µA 10 mV DC
			140 mW
			(3 to 12 V DC)		280 mW
	Single side stable		200 mW		(3 to 24 V DC)		200 mW
			(24 V DC)		400 mW
			300 mW		(48 V DC)
Nominal			(48 V DC)
			100 mW
operating
	1 coil latching		(3 to 12 V DC)		200 mW		—
power
			150 mW
			(24 V DC)
			200 mW
	2 coil latching		(3 to 12 V DC)		400 mW		—
			300 mW
			(24 V DC)
Expected	Mechanical (at 180 cpm)		108				107
	Electrical	1 A 30 V DC	2×105				105
life (min.
		resistive
opera-	(at 20 cpm)
	(1 A 30 V DC	0.5 A 125 V AC
tions)			105				—
	resistive)	resistive

Note:

1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.

Remarks

* Specifications will vary with foreign standards certification ratings.

*1 Measurement at same location as "Initial breakdown voltage" section.

*2 By resistive method, nominal voltage applied to the coil; contact carrying current: 1 A.

*3 Nominal voltage applied to the coil, excluding contact bounce time.

*4 Nominal voltage applied to the coil, excluding contact bounce time without diode. *5 Half-wave pulse of sine wave: 11 ms; detection time: 10 s.

*6 Half-wave pulse of sine wave: 6 ms. *7 Detection time: 10 s.

Characteristics

Standard

M.B.B.type

(B.B.M) type

Initial insulation resistance*1

Min. 1,000 MΩ (at 500 V DC)

Between open

750 Vrms for 1 min.

300 Vrms for 1 min.

(Detection current:

(Detection current:

contacts

Initial

10 mA)

10 mA)

breakdown

Between contact

1,000 Vrms for 1 min.

voltage

and coil

(Detection current: 10 mA)

Between contact

1,000 Vrms for 1 min.

sets

(Detection current: 10 mA)

FCC surge voltage between open

1,500 V

contacts

Operate time [Set time]*3

Max. 3 ms (Approx. 2 ms)

(at 20°C)

[Max. 3 ms (Approx. 2 ms)]

Release time [Reset time]*4

Max. 3 ms (Approx. 1 ms)

(at 20°C)

[Max. 3 ms (Approx. 2 ms)]

M.B.B. time*8

—

Min. 10 µs.

Temperature rise*2 (at 20°C)

Max. 50°C

Shock resistance

Functional*5

Min. 490 m/s2 {50G}

Destructive*6

Min. 980 m/s2 {100G}

Functional*7

176.4 m/s2 {18G}, 10 to 55 Hz

Vibration

at double amplitude of 3 mm

resistance

Destructive

294 m/s2 {30G}, 10 to 55 Hz

at double amplitude of 5 mm

Conditions for

Ambient

–40°C to +70°C

–40°C to +50°C

operation, trans-

temperature

–40°F to +158°F

–40°F to +122°F

port and storage*9

(Not freezing and

Humidity

5 to 85% R.H.

condensing at low

temperature)

Unit weight

2 Form C:

Approx. 1.5 g .053 oz

4 Form C:

Approx. 3 g .106 oz.

—

*8 M.B.B. time:

Min. 10 µs

Measuring

condition

500 Ω

5 V DC

*9 Refer to 4. Conditions for operation, transport and storage mentioned in Cautions for use (Page 178).

133

TQ

ORDERING INFORMATION

EX. TQ

2

H

L2

2M

3V

Contact arrangement

Terninal shape

Operating function

MBB function

Coil voltage (DC)

2: 2 Form C

Nil: Standard PC board

Nil: Single side stable

Nil: Standard

3, 4.5, 5, 6, 9,

4: 4 Form C

terminal

L: 1 coil latching

(B.B.M.) type

12, 24, 48* V

H: Self-clinching terminal

L2: 2 coil latching

2M: 2M.B.B. type

*48 V coil type: Single side stable only

Notes: 1. AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix “–3” like TQ2-12V-3.

2. M.B.B. contact types are available only for TQ2 type.

TYPES AND COIL DATA (at 20°C 68°F)

1. Standard (B.B.M.) type

2 Form C type

1. Single side stable

	Part No.		Nominal	Pick-up	Drop-out	Nominal	Coil	Nominal	Max.
						operating		operating	allowable
	Standard PC	Self-clinching	voltage,	voltage,	voltage,		resistance,
						current,		power,	voltage,
	board terminal	terminal	V DC	V DC (max.)	V DC (min.)		Ω (±10%)
						mA (±10%)		mW	V DC
	TQ2-3 V	TQ2H-3 V	3	2.25	0.3	46.7	64.3	140	4.5
	TQ2-4.5 V	TQ2H-4.5 V	4.5	3.38	0.45	31.1	144.6	140	6.7
	TQ2-5 V	TQ2H-5 V	5	3.75	0.5	28.1	178	140	7.5
	TQ2-6 V	TQ2H-6 V	6	4.5	0.6	23.3	257	140	9
	TQ2-9 V	TQ2H-9 V	9	6.75	0.9	15.5	579	140	13.5
	TQ2-12 V	TQ2H-12 V	12	9	1.2	11.7	1,028	140	18
	TQ2-24 V	TQ2H-24 V	24	18	2.4	8.3	2,880	200	36
	TQ2-48 V	TQ2H-48 V	48	36	4.8	6.25	7,680	300	57.6

2. 1 Coil latching

	Part No.		Nominal			Nominal	Coil	Nominal	Max.
				Set voltage,	Reset voltage,	operating		operating	allowable
	Standard PC	Self-clinching	voltage,				resistance,
				V DC (max.)	V DC (min.)	current,		power,	voltage,
	board terminal	terminal	V DC				Ω (±10%)
						mA (±10%)		mW	V DC
	TQ2-L-3 V	TQ2H-L-3 V	3	2.25	2.25	33.3	90	100	4.5
	TQ2-L-4.5 V	TQ2H-L-4.5 V	4.5	3.38	3.38	22.2	202.5	100	6.7
	TQ2-L-5 V	TQ2H-L-5 V	5	3.75	3.75	20	250	100	7.5
	TQ2-L-6 V	TQ2H-L-6 V	6	4.5	4.5	16.7	360	100	9
	TQ2-L-9 V	TQ2H-L-9 V	9	6.75	6.75	11.1	810	100	13.5
	TQ2-L-12 V	TQ2H-L-12 V	12	9	9	8.3	1,440	100	18
	TQ2-L-24 V	TQ2H-L-24 V	24	18	18	6.3	3,840	150	36

3. 2 Coil latching

	Part No.		Nominal			Nominal	Coil	Nominal	Max.
	Standard PC	Self-clinching	voltage,	Set voltage,	Reset voltage,	operating	resistance,	operating	allowable
				V DC (max.)	V DC (min.)	current,		power,	voltage,
	board terminal	terminal	V DC				Ω (±10%)
						mA (±10%)		mW	V DC
	TQ2-L2-3 V	TQ2H-L2-3 V	3	2.25	2.25	66.7	45	200	4.5
	TQ2-L2-4.5 V	TQ2H-L2-4.5 V	4.5	3.38	3.38	44.4	101.2	200	6.7
	TQ2-L2-5 V	TQ2H-L2-5 V	5	3.75	3.75	40	125	200	7.5
	TQ2-L2-6 V	TQ2H-L2-6 V	6	4.5	4.5	33.3	180	200	9
	TQ2-L2-9 V	TQ2H-L2-9 V	9	6.75	6.75	22.2	405	200	13.5
	TQ2-L2-12 V	TQ2H-L2-12 V	12	9	9	16.7	720	200	18
	TQ2-L2-24 V	TQ2H-L2-24 V	24	18	18	12.5	1,920	300	28.8

Notes: 1. Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.

2.Standard packing: Tube: 50 pcs.; Case: 1,000 pcs.

3.In case of 5 V transistor drive circuit, it is recommend to use 4.5 V type relay.

4.AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TQ2-12V-3.

134

									TQ
4 Form C type
1. Single side stable
Part No.			Nominal	Pick-up	Drop-out	Nominal	Coil	Nominal	Max.
						operating cur-		operating	allowable
Standard PC		Self-clinching	voltage,	voltage,	voltage,		resistance,
						rent,		power,	voltage,
board terminal		terminal	V DC	V DC (max.)	V DC (min.)		Ω (±10%)
						mA (±10%)		mW	V DC
TQ4-3 V		TQ4H-3 V	3	2.25	0.3	93.8	32	280	4.5
TQ4-4.5 V		TQ4H-4.5 V	4.5	3.38	0.45	62.2	72.3	280	6.7
TQ4-5 V		TQ4H-5 V	5	3.75	0.5	56.2	89	280	7.5
TQ4-6 V		TQ4H-6 V	6	4.5	0.6	46.5	129	280	9
TQ4-9 V		TQ4H-9 V	9	6.75	0.9	31.1	289	280	13.5
TQ4-12 V		TQ4H-12 V	12	9	1.2	23.3	514	280	18
TQ4-24 V		TQ4H-24 V	24	18	2.4	11.7	2,056	280	36
TQ4-48 V		TQ4H-48 V	48	36	4.8	8.3	5,760	400	57.6
2. 1 Coil latching
Part No.			Nominal			Nominal	Coil	Nominal	Max.
				Set voltage,	Reset voltage,	operating		operating	allowable
Standard PC		Self-clinching	voltage,				resistance,
				V DC (max.)	V DC (min.)	current,		power,	voltage,
board terminal		terminal	V DC				Ω (±10%)
						mA (±10%)		mW	V DC
TQ4-L-3 V		TQ4H-L-3 V	3	2.25	2.25	66.6	45	200	4.5
TQ4-L-4.5 V		TQ4H-L-4.5 V	4.5	3.38	3.38	44.4	101.2	200	6.7
TQ4-L-5 V		TQ4H-L-5 V	5	3.75	3.75	40	125	200	7.5
TQ4-L-6 V		TQ4H-L-6 V	6	4.5	4.5	33.3	180	200	9
TQ4-L-9 V		TQ4H-L-9 V	9	6.75	6.75	22.2	405	200	13.5
TQ4-L-12 V		TQ4H-L-12 V	12	9	9	16.7	720	200	18
TQ4-L-24 V		TQ4H-L-24 V	24	18	18	8.3	2,880	200	36
3. 2 Coil latching
Part No.			Nominal			Nominal	Coil	Nominal	Max.
Standard PC		Self-clinching	voltage,	Set voltage,	Reset voltage,	operating	resistance,	operating	allowable
				V DC (max.)	V DC (min.)	current,		power,	voltage,
board terminal		terminal	V DC				Ω (±10%)
						mA (±10%)		mW	V DC
TQ4-L2-3 V		TQ4H-L2-3 V	3	2.25	2.25	133	22.5	400	4.5
TQ4-L2-4.5 V		TQ4H-L2-4.5 V	4.5	3.38	3.38	88.9	50.6	400	6.7
TQ4-L2-5 V		TQ4H-L2-5 V	5	3.75	3.75	80	62.5	400	7.5
TQ4-L2-6 V		TQ4H-L2-6 V	6	4.5	4.5	66.6	90	400	9
TQ4-L2-9 V		TQ4H-L2-9 V	9	6.75	6.75	44.4	202.5	400	13.5
TQ4-L2-12 V		TQ4H-L2-12 V	12	9	9	33.3	360	400	18
TQ4-L2-24 V		TQ4H-L2-24 V	24	18	18	16.7	1,440	400	36

Notes: 1. Specified value of the pick-up, drop-out, voltage is with the condition of square wave coil pulse.

2.Standard packing: Tube: 50 pcs.; Case: 1,000 pcs.

3.In case of 5 V transistor drive circuit, it is recommend to use 4.5 V type relay.

4.1 coil latching and 2 coil latching types are also available by request. Please consult us for details.

5.AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TQ2-12V-3.

2.M.B.B. type

Single side stable

	Part No.		Nominal	Pick-up	Drop-out	Nominal	Coil	Nominal	Max.
	Standard PC	Self-clinching	voltage,	voltage,	voltage,	operating	resistance,	operating	allowable
						current,		power,	voltage,
	board terminal	terminal	V DC	V DC (max.)	V DC (min.)		Ω (±10%)
						mA (±10%)		mW	V DC
	TQ2-2M-3 V	TQ2H-2M-3 V	3	2.4	0.3	66.7	45	200	4.5
	TQ2-2M-4.5 V	TQ2H-2M-4.5 V	4.5	3.6	0.45	44.4	101	200	6.7
	TQ2-2M-5 V	TQ2H-2M-5 V	5	4	0.5	40	125	200	7.5
	TQ2-2M-6 V	TQ2H-2M-6 V	6	4.8	0.6	33.3	180	200	9
	TQ2-2M-9 V	TQ2H-2M-9 V	9	7.2	0.9	22.2	405	200	13.5
	TQ2-2M-12 V	TQ2H-2M-12 V	12	9.6	1.2	16.7	720	200	18
	TQ2-2M-24 V	TQ2H-2M-24 V	24	19.2	2.4	8.3	2,880	200	36

Notes: 1. Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.

2.Standard packing: Tube: 50 pcs.; Case: 1,000 pcs.

3.In case of 5 V transistor drive circuit, it is recommend to use 4.5 V type relay.

4.AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TQ2-12V-3.

135