NAIS TN2-L2-H-9V, TN2-L2-H-6V, TN2-L2-H-5V, TN2-L2-H-4.5V, TN2-L2-H-24V Datasheet

SLIM POLARIZED RELAY TN-RELAYS

	5.6
14	.220

.551

9.8

.386

FEATURES

•Small size for minimal PC board mounting requirements

•Small header area makes higher density mounting possible

•High sensitivity: 140 mW nominal operating power (single side stable 3-12

mm inch

V type)

•Surge voltage withstand: 1500 V FCC Part 68

•Sealed construction allows automatic cleaning

•Self-clinching terminal also available

SPECIFICATIONS

Contact

	Arrangement				2 Form C
	Initial contact resistance, max.				60 mΩ
	(By voltage drop 6 V DC 1A)
	Contact material				Gold-clad silver
			Nominal switching capacity		1 A 30 V DC,
			(resistive load)		0.5 A 125 V AC
			Max. switching power		30 W, 62.5 VA
	Rating		(resistive load)
			Max. switching voltage		110 V DC,125 V AC
			Max. switching current		1 A
			Min. switching capacity 1		10 µA 10 mV DC
					140 mW (3 to 12 V DC)
			Single side stable		200 mW (24 V DC)
	Nominal				300 mW (48 V DC)
	operating		1 coil latching		100 mW (3 to 12 V DC)
	power				150 mW (24 V DC)
			2 coil latching		200 mW (3 to 12 V DC)
					300 mW (24 V DC)
			Mechanical (at 180 cpm)		108
	Expected			1 A 30 V DC	2 × 105
	life (min.		Electrical	resistive load
	operations)		(at 20 cpm)	0.5 A 125 V AC	105
				resistive load

Note:

1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.

Remarks

* Specifications will vary with foreign standards certification ratings.

*1 Measurement at same location as "Initial breakdown voltage" section.

*2 By resistive method, nominal voltage applied to the coil; contact carrying current: 1 A.

*3 Nominal voltage applied to the coil, excluding contact bounce time.

*4 Nominal voltage applied to the coil, excluding contact bounce time without diode.

Characteristics

	Initial insulation resistance*1					Min. 1,000 MΩ (at 500 V DC)
			Between open			750 Vrms for 1 min.
	Initial		contacts			(Detection current: 10 mA)
			Between contact and			1,000 Vrms for 1 min.
	breakdown
			coil			(Detection current: 10 mA)
	voltage
			Between contact sets			1,000 Vrms for 1 min.
						(Detection current: 10 mA)
	FCC surge voltage between open					1,500 V
	contacts
	Temperature rise*2 (at 20°C)					Max. 50°C
	Operate time [Set time]*3 (at 20°C)					Max. 3 ms (Approx. 2 ms)
						[Max. 3 ms (Approx. 2 ms)]
	Release time [Reset time]*4					Max. 3 ms (Approx. 1 ms)
	(at 20°C)					[Max. 3 ms (Approx. 2 ms)]
	Shock resistance				Functional*5	Min. 490 m/s2 {50G}
					Destructive*6	Min. 980 m/s2 {100G}
					Functional*7	176.4 m/s2 {18G}, 10 to 55 Hz
						at double amplitude of 3 mm
	Vibration resistance
					Destructive	294 m/s2 {30G}, 10 to 55 Hz
						at double amplitude of 5 mm
	Conditions for oper-				Ambient	–40°C to +70°C
	ation, transport and				temperature	–40°F to +158°F
	storage*8
	(Not freezing and				Humidity	5 to 85% R.H.
	condensing at low
	temperature)
	Unit weight					Approx. 1.5 g .053 oz

*5 Half-wave pulse of sine wave: 11 ms; detection time: 10 s. *6 Half-wave pulse of sine wave: 6 ms.

*7 Detection time: 10 s.

*8 Refer to 4. Conditions for operation, transport and storage mentioned in Cautions for use (Page 178).

ORDERING INFORMATION

Ex. TN

2

L2

H

12V

Contact arrangement

Operating function

Terminal shape

Coil voltage(DC)

2: 2 Form C

Nil: Single side stable

Nil: Standard PC board terminal

3,4.5,5,6,9,12,

L: 1

coil latching

H: Self-clinching terminal

24,48*V

L2: 2 coil latching

*48 V coil type: Single side stable only

Note: AgPd stationary contact types available for high resistance against contact sticking.

When ordering, please add suffix “–3” like TN2–12V–3.

150

									TN
	TYPES AND COIL DATA (at 20°C 68°F)
	1. Single side stable
	Part No.		Nominal	Pick-up	Drop-out	Nominal	Coil	Nominal	Max.
						operating		operating	allowable
	Standard PC	Self-clinching	voltage,	voltage,	voltage,		resistance,
						current,		power,	voltage,
	board terminal	terminal	V DC	V DC (max.)	V DC (min.)		Ω (±10%)
						mA (±10%)		mW	V DC
	TN2-3 V	TN2-H-3 V	3	2.25	0.3	46.7	64.3	140	4.5
	TN2-4.5 V	TN2-H-4.5 V	4.5	3.38	0.45	31.1	145	140	6.7
	TN2-5 V	TN2-H-5 V	5	3.75	0.5	28.1	178	140	7.5
	TN2-6 V	TN2-H-6 V	6	4.5	0.6	23.3	257	140	9
	TN2-9 V	TN2-H-9 V	9	6.75	0.9	15.5	579	140	13.5
	TN2-12 V	TN2-H-12 V	12	9	1.2	11.7	1,028	140	18
	TN2-24 V	TN2-H-24 V	24	18	2.4	8.3	2,880	200	36
	TN2-48 V	TN2-H-48 V	48	36	4.8	6.25	7,680	300	57.6
	2. 1 Coil latching
	Part No.		Nominal			Nominal	Coil	Nominal	Max.
	Standard PC	Self-clinching	voltage,	Set voltage,	Reset voltage,	operating	resistance,	operating	allowable
				V DC (max.)	V DC (max.)	current,		power,	voltage,
	board terminal	terminal	V DC				Ω (±10%)
						mA (±10%)		mW	V DC
	TN2-L-3 V	TN2-L-H-3 V	3	2.25	2.25	33.3	90	100	4.5
	TN2-L-4.5 V	TN2-L-H-4.5 V	4.5	3.38	3.38	22.2	202.5	100	6.7
	TN2-L-5 V	TN2-L-H-5 V	5	3.75	3.75	20	250	100	7.5
	TN2-L-6 V	TN2-L-H-6 V	6	4.5	4.5	16.7	360	100	9
	TN2-L-9 V	TN2-L-H-9 V	9	6.75	6.75	11.1	810	100	13.5
	TN2-L-12 V	TN2-L-H-12 V	12	9	9	8.3	1,440	100	18
	TN2-L-24 V	TN2-L-H-24 V	24	18	18	6.3	3,840	150	36
	3. 2 Coil latching
	Part No.		Nominal			Nominal	Coil	Nominal	Max.
				Set voltage,	Reset voltage,	operating		operating	allowable
	Standard PC	Self-clinching	voltage,				resistance,
				V DC (max.)	V DC (max.)	current,		power,	voltage,
	board terminal	terminal	V DC				Ω (±10%)
						mA (±10%)		mW	V DC
	TN2-L2-3 V	TN2-L2-H-3 V	3	2.25	2.25	66.7	45	200	4.5
	TN2-L2-4.5 V	TN2-L2-H-4.5 V	4.5	3.38	3.38	44.4	101.2	200	6.7
	TN2-L2-5 V	TN2-L2-H-5 V	5	3.75	3.75	40	125	200	7.5
	TN2-L2-6 V	TN2-L2-H-6 V	6	4.5	4.5	33.3	180	200	9
	TN2-L2-9 V	TN2-L2-H-9 V	9	6.75	6.75	22.2	405	200	13.5
	TN2-L2-12 V	TN2-L2-H-12 V	12	9	9	16.7	720	200	18
	TN2-L2-24 V	TN2-L2-H-24 V	24	18	18	12.5	1,920	300	28.8

Notes:

1.Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.

2.Standard packing: Tube: 50 pcs.; Case: 1,000 pcs.

3.In case of 5 V drive circuit, it is recommended to use 4.5 V type relay.

4.AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TN2-12V-3.

DIMENSIONS	mm inch
Standard PC board terminal	PC board pattern (Copper-side view)

	14	5.6	10.16
	551	.220	.400
	9.5		2.54
9.8			.100
.374
.386
3.5
.138			10-1.0 dia. hole
		0.25	10-.039 dia. hole

2.54	0.5	1.385	.010
.100	.020	.055	2.54
			.100

2.54 .100

Tolerance: ±0.1 ±.004

		Self-clinching terminal						Schematic (Bottom view)
					• Single side stable				• 1-coil latching			• 2-coil latching
		14		5.6	(Deenergized condition)				(Reset condition)			(Reset condition)
		551		.220
9.8	9.5				1	2	3	4 5	1 2 3	4	5	1 2 3		4	5
.374
.386
3.5
.138					10 9		8 7 6		10 9 8	7	6	10 9	8	7	6
				0.25
					Direction indication*				Direction indication*			Direction indication*
	2.54	0.5	1.385	.010 2.54
	.100	.020	.055	.100

*Orientation stripe located on top of relay

General tolerance: ±0.3 ±.012

151