TESTING
SMALL POLARIZED RELAY WITH HIGH SENSITIVITY 50mW
TX-S RELAYS
15 |
7.4 |
|
|
FEATURES |
.591 |
.291 |
|
|
|
|
|
|
High sensitivity |
|
|
8.2 |
15 |
7.4 |
|
|
.323 |
.591 |
.291 |
• 50mW nominal operating power |
|
|
|
||
|
|
|
8.4 |
(single side stable 1.5-12V) |
|
|
|
.331 |
|
|
|
|
|
• Useful for electric-power-saving |
mm inch |
|
|
SA type |
Approx. 0.3µV low thermal electromo- |
|
|
|
tive force |
Outstanding surge resistance
Surge withstand between open contacts: 1,500V 10×160µs (FCC part 68)
Surge withstand between contacts and coil:
2,500V 2×10µs (Bellcore)
SPECIFICATIONS
Contact
Arrangement |
|
|
|
2 Form C |
|
|
|
||||
Initial contact resistance, max. |
100 mΩ |
||||
(By voltage drop 6 V DC 1 A ) |
|||||
|
|||||
|
|
|
|||
Contact material |
|
Gold-clad silver alloy |
|||
|
|
|
|
||
|
Nominal switching capacity |
1 A 30 V DC |
|||
|
(resistive load) |
||||
|
|
||||
|
|
|
|||
|
Max. switching power |
30 W (DC) |
|||
Rating |
(resistive load) |
||||
|
|||||
|
|
|
|
||
|
Max. switching voltage |
110 V DC |
|||
|
|
|
|||
|
Max. switching current |
1 A |
|||
|
|
|
|||
|
Min. switching capacity 1 |
10 µA 10 mV DC |
|||
|
Single side stable |
50 mW (1.5 to 12 V DC) |
|||
|
70 mW (24 V DC) |
||||
Nominal |
|
|
|
||
|
|
|
|
||
|
|
|
35 mW (1.5 to 12 V DC) |
||
operating |
1 coil latching |
|
|||
|
50 mW (24 V DC) |
||||
power |
|
|
|
||
|
|
|
|
||
2 coil latching |
|
70 mW (1.5 to 12 V DC) |
|||
|
|
||||
|
|
150 mW (24 V DC) |
|||
|
|
|
|
||
|
|
|
|||
Expected |
Mechanical (at 180 cpm) |
5×107 |
|||
life (min. |
Electrical |
|
1 A 30 V DC |
2×105 |
|
operations) |
(at 20 cpm) |
|
resistive |
||
|
|
||||
|
|
|
|
|
Note:
1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.
Remarks
* Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section. *2 Detection current: 10mA
*3 Excluding contact bounce time.
*4 By resistive method; nominal voltage applied to the coil; contact carrying current: 1 A.
*5 Half-wave pulse of sine wave: 6 ms; detection time: 10 s
Characteristics
Initial insulation resistance*1 |
Min. 1,000 MΩ (at 500 V DC) |
|||
Initial |
Between open contacts |
750 Vrms for 1min. |
||
|
|
|
||
breakdown |
Between contact sets |
1,000 Vrms for 1min. |
||
voltage*2 |
|
|
|
|
Between contacts and coil |
1,800 Vrms for 1min. |
|||
|
||||
|
|
|
||
|
Between open contacts |
1,500V (FCC Part 68) |
||
Initial surge |
(10 × 160µs) |
|
||
|
|
|||
voltage |
Between contacts and coil |
2,500V (Bellcore) |
||
|
(2 × 10 µs) |
|
||
|
|
|
||
Operate time [Set time]*3 |
|
Max. 5 ms (Approx. 3 ms) |
||
(at 20°C)(at nominal voltage) |
[Max. 5 ms (Approx. 3 ms)] |
|||
Release time (without diode) |
Max. 5 ms (Approx. 1.5 ms) |
|||
[Reset time]*3 |
|
|||
|
[Max. 5 ms (Approx. 3 ms)] |
|||
(at 20°C)(at nominal voltage) |
||||
|
||||
Temperature rise*4 (at 20°C) |
Max. 50°C |
|||
Shock resistance |
Functional*5 |
Min. 750 m/s2 {75 G} |
||
Destructive*6 |
Min. 1,000 m/s2 {100 G} |
|||
|
|
|||
|
|
Functional*7 |
10 to 55 Hz at double |
|
|
|
amplitude of 3.3 mm |
||
Vibration resistance |
|
|||
|
|
|||
Destructive |
10 to 55 Hz at double |
|||
|
|
|||
|
|
amplitude of 5 mm |
||
|
|
|
||
|
|
|
||
Conditions for operation, |
Ambient |
–40°C to +70°C |
||
transport and storage*8 |
temperature |
–40°F to +158°F |
||
(Not freezing and condensing |
|
|
||
Humidity |
5 to 85% R.H. |
|||
at low temperature) |
||||
|
|
|||
|
|
|
|
|
Unit weight |
|
|
Approx. 2 g .071 oz |
|
|
|
|
|
*6 Half-wave pulse of sine wave: 6 ms *7 Detection time: 10 s
*8 Refer to 4. Conditions for operation, transport and storage mentioned in Cautions for use (Page 178).
TYPICAL APPLICATIONS
• Telephone equipment |
• Communications equipment |
• Measuring equipment |
• Office Automation equipment |
ORDERING INFORMATION
|
|
|
Ex. TXS |
|
2 |
|
|
SA |
|
– |
|
L |
|
– |
|
H |
|
– |
|
3V |
|
– |
|
|
|
Z |
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
Contact arrangement |
Surface-mount availability |
|
|
|
|
|
|
|
Operating function |
|
Terminal shape |
Coil voltage (DC) |
Packing style |
||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||
2: 2 Form C |
Nil: Standard PC board terminal type or |
|
|
|
|
Nil: Single side |
|
Nil: Standard PC |
1.5, 3, 4.5, 6, 9, |
Nil: Tube packing |
|||||||||||||||||||||||||||||||||||
|
|
|
Nil: self-clinching terminal type |
|
|
|
|
|
|
|
|
Nil: stable |
|
|
|
|
|
board terminal or |
12, 24 V |
|
|
|
Z: Tape and reel |
||||||||||||||||||||||
|
|
|
SA: Standard surface-mount terminal type |
|
|
|
|
L: 1 coil latching |
surface-mount |
|
|
|
|
|
|
|
|
|
|
|
packing(piked |
||||||||||||||||||||||||
|
|
|
SL: High connection reliability surface-mount |
|
|
|
|
L2: 2 coil latching |
terminal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
from the 8/9/10/12 |
||||||||||||||||||||
|
|
|
SL: terminal type |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
H: Self-clinching |
|
|
|
|
|
|
|
|
-pin side |
||||||||||||||||
|
|
|
SS: Space saving surface-mount terminal type |
|
|
|
|
|
|
|
|
|
terminal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Notes: 1. Tape and reel (picked from 1/3/4/5-pin side) is also available by request. Part number suffix “-X” is needed when ordering. (ex.) TXS2SA-3 V-X
2. Tape and reel packing symbol “-Z” or “-X” are not marked on the relay.
167
TX-S
TYPES AND COIL DATA (at 20°C 68°F)
1) Standard PC board terminal type and self-clinching terminal type
Single side stable
Part No. |
|
Pick-up |
Drop-out |
Nominal |
Coil |
Nominal |
Max. |
||
Standard PC |
Self-clinching |
Nominal |
voltage, |
voltage, |
operating |
resistance, |
operating |
Allowable |
|
voltage, V DC |
current, |
power, |
voltage, |
||||||
board terminal |
terminal |
V DC (max.) |
V DC (min.) |
Ω (±10%) |
|||||
|
mA (±10%) |
mW |
V DC |
||||||
|
|
|
|
|
|
||||
TXS2-1.5V |
TXS2-H-1.5V |
1.5 |
1.2 |
0.15 |
33.3 |
45 |
50 |
2.2 |
|
TXS2-3V |
TXS2-H-3V |
3 |
2.4 |
0.3 |
16.7 |
180 |
50 |
4.5 |
|
TXS2-4.5V |
TXS2-H-4.5V |
4.5 |
3.6 |
0.45 |
11.1 |
405 |
50 |
6.7 |
|
TXS2-6V |
TXS2-H-6V |
6 |
4.8 |
0.6 |
8.3 |
720 |
50 |
9 |
|
TXS2-9V |
TXS2-H-9V |
9 |
7.2 |
0.9 |
5.6 |
1,620 |
50 |
13.5 |
|
TXS2-12V |
TXS2-H-12V |
12 |
9.6 |
1.2 |
4.2 |
2,880 |
50 |
18 |
|
TXS2-24V |
TXS2-H-24V |
24 |
19.2 |
2.4 |
2.9 |
8,229 |
70 |
36 |
1 coil latching
Part No. |
Nominal |
|
|
Nominal |
Coil |
Nominal |
Max. |
||
|
|
Set voltage, |
Reset voltage, |
operating |
operating |
Allowable |
|||
Standard PC |
Self-clinching |
voltage, |
resistance, |
||||||
V DC (max.) |
V DC (Max.) |
current, |
power, |
voltage, |
|||||
board terminal |
terminal |
V DC |
Ω (±10%) |
||||||
|
|
mA (±10%) |
mW |
V DC |
|||||
|
|
|
|
|
|
||||
TXS2-L-1.5V |
TXS2-L-H-1.5V |
1.5 |
1.2 |
1.2 |
23.3 |
64.3 |
35 |
2.2 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L-3V |
TXS2-L-H-3V |
3 |
2.4 |
2.4 |
11.7 |
257 |
35 |
4.5 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L-4.5V |
TXS2-L-H-4.5V |
4.5 |
3.6 |
3.6 |
7.8 |
579 |
35 |
6.7 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L-6V |
TXS2-L-H-6V |
6 |
4.8 |
4.8 |
5.8 |
1,029 |
35 |
9 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L-9V |
TXS2-L-H-9V |
9 |
7.2 |
7.2 |
3.9 |
2,314 |
35 |
13.5 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L-12V |
TXS2-L-H-12V |
12 |
9.6 |
9.6 |
2.9 |
4,114 |
35 |
18 |
|
TXS2-L-24V |
TXS2-L-H-24V |
24 |
19.2 |
19.2 |
2.1 |
11,520 |
50 |
36 |
2 coil latching
Part No. |
Nominal |
|
|
Nominal |
Coil |
Nominal |
Max. |
||
|
|
Set voltage, |
Reset voltage, |
operating |
operating |
Allowable |
|||
Standard PC |
Self-clinching |
voltage, |
resistance, |
||||||
V DC (max.) |
V DC (Max.) |
current, |
power, |
voltage, |
|||||
board terminal |
terminal |
V DC |
Ω (±10%) |
||||||
|
|
mA (±10%) |
mW |
V DC |
|||||
|
|
|
|
|
|
||||
TXS2-L2-1.5V |
TXS2-L2-H-1.5V |
1.5 |
1.2 |
1.2 |
46.7 |
32.1 |
70 |
2.2 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L2-3V |
TXS2-L2-H-3V |
3 |
2.4 |
2.4 |
23.3 |
129 |
70 |
4.5 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L2-4.5V |
TXS2-L2-H-4.5V |
4.5 |
3.6 |
3.6 |
15.6 |
289 |
70 |
6.7 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L2-6V |
TXS2-L2-H-6V |
6 |
4.8 |
4.8 |
11.7 |
514 |
70 |
9 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L2-9V |
TXS2-L2-H-9V |
9 |
7.2 |
7.2 |
7.8 |
1,157 |
70 |
13.5 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L2-12V |
TXS2-L2-H-12V |
12 |
9.6 |
9.6 |
5.8 |
2,057 |
70 |
18 |
|
|
|
|
|
|
|
|
|
|
|
TXS2-L2-24V |
TXS2-L2-H-24V |
24 |
19.2 |
19.2 |
6.3 |
3,840 |
150 |
36 |
|
|
|
|
|
|
|
|
|
|
Notes:
1.Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
2.Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
2) Surface-mount terminal type
Single side stable
|
Nominal |
|
Drop-out |
Nominal |
|
Nominal |
Max. Allowable |
|
|
Pick-up voltage, |
operating |
Coil resistance, |
|||||
Part No. |
voltage, |
voltage, |
operating power, |
voltage, |
||||
V DC (max.) |
current, |
Ω (±10%) |
||||||
|
V DC |
V DC (min.) |
mW |
V DC |
||||
|
|
mA (±10%) |
|
|||||
|
|
|
|
|
|
|
||
TXS2S -1.5 V |
1.5 |
1.2 |
0.15 |
33.3 |
45 |
50 |
2.2 |
|
|
|
|
|
|
|
|
|
|
TXS2S -3 V |
3 |
2.4 |
0.3 |
16.7 |
180 |
50 |
4.5 |
|
|
|
|
|
|
|
|
|
|
TXS2S -4.5 V |
4.5 |
3.6 |
0.45 |
11.1 |
405 |
50 |
6.7 |
|
|
|
|
|
|
|
|
|
|
TXS2S -6 V |
6 |
4.8 |
0.6 |
8.3 |
720 |
50 |
9 |
|
|
|
|
|
|
|
|
|
|
TXS2S -9 V |
9 |
7.2 |
0.9 |
5.6 |
1,620 |
50 |
13.5 |
|
|
|
|
|
|
|
|
|
|
TXS2S -12 V |
12 |
9.6 |
1.2 |
4.2 |
2,880 |
50 |
18 |
|
|
|
|
|
|
|
|
|
|
TXS2S -24 V |
24 |
19.2 |
2.4 |
2.9 |
8,229 |
70 |
36 |
|
|
|
|
|
|
|
|
|
168