Boss DC-2W User Manual

Owner’s Manual	English

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

*

5

1

0

0

0

6

3

5

7

1

-

0

2

*

Main Features

55 This is a WAZA CRAFT series effect pedal crafted with a high-quality analog original circuit design. 55 The “Dimension” effect add unique natural spaciousness and rich depth to your sound.

55 This pedal also reproduces the sound of “SDD-320 Dimension D” used by countless recording studios, providing a more sparkling sound.

Panel Descriptions

DC IN jack

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series; sold separately).

CHECK indicator

This indicator shows whether the effect is ON/OFF, and also doubles as the battery check indicator. The indicator lights when the effect is ON.

*Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet of the correct voltage.

*If the AC adaptor is connected while a battery is installed, the

power supply is drawn from the AC adaptor. AC Adaptor(PSA series; sold separately)

MODE SELECTOR [1]–[4] buttons

Select the sound. Higher numbers produce a deeper effect.

By pressing two buttons simultaneously you can combine the effects.

*The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace the battery when the LED is dim or does not light. For instructions, refer to “Changing the Battery.”

*The CHECK indicator shows whether the effect is being applied or not. It does not indicate whether the power to the device is on or not.

S/SDD-320 switch

Switches the sound variation.

Reproduces the sound of the original DC-2.

S (Standard)

OUTPUT A (MONO) jack

Outputs the effect sound in mono.

Guitar Amplifier

OUTPUT B jack

Use this jack for stereo output.

By using this in conjunction with the OUTPUT A (MONO) jack you can obtain spacious sound.

Guitar Amplifier

Pedal switch

This switch turns the effect on/off.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the battery.

*For instructions on changing the battery, refer to “Changing the Battery.”

Reproduces a sparkling sound of the SDD-320.

SDD-320

Electric Guitar

INPUT jack

Electronic Musical Instrument (e.g., keyboards)

Connect the output of your electric guitar, electronic musical instrument, or effect unit to this jack.

*The INPUT A (MONO) jack doubles as the power switch. Power to the unit is turned on when you plug into the INPUT A (MONO) jack; the power is turned off when the cable is unplugged. To prevent unnecessary battery consumption, be sure to disconnect the plug from the INPUT A (MONO) jack when not using the effects unit.

OUTPUT Jacks

Changing the Battery

Intellectual Property Right

Mono output

Effect sound

Stereo output

Effect sound (L)

Effect sound (R)

MEMO

The audio output of this unit does not support mono mix (stereo input / mono output).

To obtain the optimal Dimension effect, we recommend that you use the unit with stereo output.

Precautions When Connecting

*To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.

*Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on

equipment in the wrong order, you risk causing malfunction or equipment failure.

When powering up: Turn on the power to your guitar amp last. When powering down: Turn off the power to your guitar amp first.

*Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

Use of Battery

*The life of the included battery may be limited as its primary purpose was for testing during assembly.

*If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

*When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible.

*Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.

*If operating this unit on battery, please use alkaline battery.

1.	Hold down the	Thumbscrew	Pedal
	pedal and loosen		Spring Base
	the thumbscrew,
		Battery Snap
	then open the
		Cord	Coil Spring
	pedal upward.
*	The pedal can be		Guide Bush
	opened without		Hole
	detaching the	Battery
	thumbscrew	Snap	Battery Housing
	completely.

9 V Battery

2.Remove the old battery from the battery housing, and remove the snap cord connected to it.

3.Connect the snap cord to the new battery, and place the battery inside the battery housing.

*Be sure to carefully observe the battery’s polarity (+ versus -).

4.Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal.

*Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.

5.Finally, hold down the pedal while tightening the thumbscrew into the guide bush hole.

Specifications

BOSS DC-2W: Dimension C

	Nominal Input Level	-20 dBu
	Input Impedance	2.2 MΩ
	Nominal Output Level	-20 dBu
	Output Impedance	1 kΩ
	Recommended Load	10 kΩ or greater
	Impedance
	Power Supply	DC 9 V: Alkaline battery (9 V, 6LR61), AC
		adaptor (sold separately)
		65 mA
		* Expected battery life under continuous
	Current Draw	use:
		Alkaline battery: Approx. 6 hours
		These figures will vary depending on the
		actual conditions of use.
	Dimensions	73 (W) x 129 (D) x 59 (H) mm
		2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
	Weight	450 g
	(including battery)	1 lb
	Accessories	Owner’s Manual, Leaflet (“USING THE
		UNIT SAFELY,”“IMPORTANT NOTES,” and
		“Information”), Alkaline battery (9 V, 6LR61)
	Option	AC adaptor (PSA series)
	(sold separately)

* 0 dBu = 0.775 Vrms

*This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.

*Roland, BOSS, andWAZA CRAFT are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.

*CMSIS-RTOS RTX Version 4.70.1

Copyright (c) 1999-2009 KEIL, 2009-2015 ARM Germany GmbH All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

55 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

55 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

55 Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

For the USA

SUPPLIER’S DECLARATION OF

CONFORMITY

Compliance Information Statement

Model Name :	DC-2W
Type of Equipment :	Guitar E ects
Responsible Party :	Roland Corporation U.S.
Address :	5100 S. Eastern Avenue Los Angeles,
	CA 90040-2938
Telephone :	[phone]

© 2018 Roland Corporation