BOSCH TES 80323 User Manual [ru]

0 (0)

www.bosch-home.com/welcome

TES803../TES805../TES807..

en Instruction manual fr Mode d’emploi

nl Gebruiksaanwijzing pl Instrukcja obsługi cs Návod k použití

ru Инструкция по эксплуатации

TES803_805_807_1RW.indb 1

08.05.2013 14:52:50

en	English	2

fr	Français	28

nl	Nederlands	54

pl	Polski	80

cs	Čeština	106

ru	Pycckий	131

AIncluded in delivery (see page 4) Contenu de l’emballage (voir page 30) De verpakking bevat (zie pagina 56)

Zakres dostawy (patrz strona 82)

Rozsah dodávky (na straně 108)

Объем поставки (см. стр. 133)

TES803_805_807_1RW.indb 2

08.05.2013 14:52:53

B		5a 5b
2		8
3		7
4		4
		5c

27 28

TES805

TES807

TES803_805_807_1RW.indb 3

08.05.2013 14:52:53

C	14

D E

23a

23c

10a

10c

10b

23b

10d

TES803_805_807_1RW.indb 4

08.05.2013 14:52:56

20a

22	20a	21
22

20a

TES803_805_807_1RW.indb 5

08.05.2013 14:52:56

2		en
Dear Coffee Connoisseur,	Contents
Congratulations on purchasing this fully	Safety instructions	3
automatic espresso machine from Bosch.	Included in delivery	4
	At a glance	4
	Before using for the first time	5
These operating instructions describe vari-	Controls	6
ous appliance designs, which differ in detail.	Displays	8
Each appliance is assigned an E-number,	Display settings	9
e.g. TES803. The E-No. of the respective	Customising	10
appliance can be found on the packaging or	Child-proof lock	11
rating label 25.	Menu settings	12
	Preparation using coffee beans	14
Please also refer to the quick reference	Preparation using ground coffee	15
guide. This can be kept in a special storage	Preparing milk froth and warm milk	16
compartment 22 until the appliance is used	Dispensing hot water	17
again.	Maintenance and daily cleaning	17
	Service Programmes	20
	Tips on energy saving	24
	Frost protection	24
	Storing accessories	24
	Accessories	24
	Disposal	25
	Guarantee	25
	Technical specifications	25
	Simple troubleshooting	26

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 2

08.05.2013 14:52:57

Safety instructions

Please read through the instructions carefully and proceed accordingly; store in a safe place!

This fully automatic espresso machine is designed for the preparation of small amounts of coffee for domestic use or for use in household-like, noncommercial environments. Householdlike environments include staff areas in shops, offices, agricultural and other

small businesses or for use by guests at bed-and-breakfast establishments, small hotels and similar residential facilities.

¡¡ Danger of electric shock!

Connect and operate the appliance only in accordance with the specifications on the rating plate.

Use only if power cord and appliance show no signs of damage.

In the event of a malfunction, unplug the appliance immediately.

To avoid potential hazards, repairs such as replacing a damaged cable, must only be carried out by our customer service personnel.

Never immerse the appliance or mains cable in water.

Unplug the appliance before cleaning it. Do not use a steam cleaner.

Use the appliance indoors and at room temperature only.

Do not allow persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, to use this appliance, unless they are being supervised or have been given instruction concerning use of the appliance by a person responsible for their safety.

Keep children away from the appliance.

Children should be supervised to ensure that they do not play with the appliance.

Please store descaling and cleaning agents in a safe place, out of reach of children. Do not drink cleaning agents.

¡¡ Risk of scalding!

The milk frother 10 for milk / hot water gets very hot. After use, allow to cool down first before touching.

¡¡ Warning!

Adjust the grinding unit only while it is running! Otherwise the appliance may be damaged. Do not reach into the grinding unit.

ONLY TES807

¡¡ Warning!

The cup warmer 27 gets very hot!

TES80.. | 04/2013

TES803_805_807_1RW.indb 3

08.05.2013 14:52:57

4			en
Included in delivery
(Figure A on the fold-out pages)
1	Fully automatic espresso machine	ONLY TES805 / TES807
	TES803 / 805 / 807	7	Milk container, insulated
2	Instruction manual	ONLY TES807
3	Quick reference guide	ONLY TES807
4	Milk frother	8	Water filter

5Water hardness testing strip

6Measuring spoon

At a glance

(Figures B, C, D, E and F on the fold-out pages)
1	Power on/off switch O / I	16	Aroma cover
2	Customising button á	17	Selector for grind setting
3	Service programmes button à	18	Powder compartment
4	Selection buttons < >		(ground coffee / cleaning tablet)
5	Display	19	Door to brewing unit
	a) Status line	20	Brewing unit
	b) Selection line		a) Lock
6	c) Navigation line	21	b) Cover
6	Rotary knob for display settings	21	Sliding button
7	Info menu button j	22	Storage compartment for quick
8	start button (drinks / programmes)		reference guide
9	Coffee outlet,	23	Drip tray
	height-adjustable and swivelling		a) Panel
10	Milk system,		b) Grate
	height-adjustable and removable	24	c) Coffee grounds container
	(milk / hot water)	24	Cable storage compartment
	a) Upper part	25	Rating label (E-No.; FD)
	b) Lower part
	c) Suction hose	ONLY TES805 / TES807
11	d) Suction pipe	26	Milk container, insulated
11	Removable water tank
12	Lid for water tank	ONLY TES807
13	Storage compartment for	27	Cup warming function
14	measuring spoon	28	Button for cup warming function,
14	Measuring spoon	29	illuminated
15	(insertion aid for water filter)	29	Water filter
15	Bean container

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 4

08.05.2013 14:52:57

Before using for the fi rst time

General

Fill the water tank with pure, cold, uncarbonated water only and preferably use only beans or coffee blends suitable for fully automatic espresso and coffee machines. Do not use coffee beans that have been glazed, caramelised or treated with other additives containing sugar, since they will block the brewing unit.

The water hardness setting can be adjusted on this appliance. The factory setting for the water hardness is 4. Check the hardness of the water you use with the enclosed test strip. If a value other than water hardness

4 is displayed, change the setting on the appliance accordingly after switching on (see “Menu settings – WATER HARDNESS”).

Setting up the appliance

●Place the fully automatic espresso machine on a fl at, water-resistant surface that can take its weight.

Important: Only use the appliance in frostfree rooms. If the appliance has been transported or stored at temperatures below

0°C, wait at least 3 hours before operation.

●Pull out the mains plug from the cable compartment 24 and plug it in. Adjust the length of the cable by pushing it back in and pulling it out. To do this, place the appliance with its back fl ush with the edge of the work surface and either pull the cable downwards or push it upwards.

●Lift the lid of the water tank 12.

●Remove and rinse the water tank 11 and fi ll it with fresh, cold water. Do not fi ll above the “max” mark.

●Replace the water tank 11 and push it fi rmly downwards into place.

●Close the water tank lid 12 again.

●Fill the bean container 15 with coffee beans.

●Press the power switch 1 O / I . The start button 8 lights up and the different languages appear in the display 5.

The following languages can be selected:

TES8.. DE
DEUTSCH	ENGLISH
FRANÇAIS	ITALIANO
TES8.. RW
ENGLISH	Русский
NEDERLANDS	FRANÇAIS
ITALIANO	SVENSKA
ESPAÑOL	POLSKI
Українська	MAGYAR
TÜRKÇE	DANSK
NORSK	SUOMI
PORTUGUÊS	ČEšTINA
ΕλληνικA

●Use the buttons < and > 4 to select the language in which you want the display texts to appear.

SPRACHE

ENGLISH

FRANÇAIS

The selected language is highlighted.

●Press the start button 8. The language you selected is saved.

●The brand logo lights up in the display 5. The appliance now heats up and rinses. Some water will run out of the coffee outlet 9.

TES80.. | 04/2013

TES803_805_807_1RW.indb 5

08.05.2013 14:52:57

●●The appliance is ready for use when the symbols for the drink selection and the start button 8 light up in the display 5.

ESPRESSO

ËË Í

Â Ã À Á Å Æ

Info: The factory settings of the fully automatic espresso machine are programmed for optimal performance. The appliance switches off automatically after 1 hour (see

“Menu settings – AUTO OFF AFTER”).

Note: If the appliance is being used for the first time, the service programme has been run, or the appliance has not been operated for a long period, the first beverage will not have the full Aroma and should not be consumed.

When the fully automatic espresso machine is first used, you will achieve a suitably thick and stable “crema” only after the first few cups have been dispensed.

Controls

Power on/off switch O / I

The power on/off switch 1 O / I is used to switch the appliance on or off. The appliance rinses automatically when it is switched on and off.

The appliance will not rinse if:

●●it is still warm when switched on. ●●there was no coffee drawn before

switching off.

The appliance is ready for use when the symbols for the drink selection and the start button 8 light up in the display 5.

Customising button á

The appliance provides the option of saving and calling up customised settings for coffee drinks. Please refer to the section

“Customising” for information on how to save and call up these settings.

Service programmes button à

Press the à button 3 briefly to call up the selection of service programmes. Please run the programme as described in “Service Programmes”.

Press and hold to activate or deactivate the child-proof lock, see “Child-proof lock”.

Rotary knob

Turn the rotary knob 6 to the left or right to navigate through the display 5, or to adjust parameters in the menu.

Selection buttons < and >

Press the selection buttons 4 < and > to navigate up and down through the menu levels (navigation line 5c).

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 6

08.05.2013 14:52:57

Display

The display 5 uses symbols to indicate the selection options, coffee strength and percup quantity, and uses text to indicate settings, ongoing processes and messages.

The rotary knob 6 and selection buttons 4 can be used to change settings. The selected setting is highlighted by a frame.

ESPRESSO	ËË Í 5a

Â Ã À Á Å Æ 5b

Example:

The status line 5a shows the name of the type of drink, along with the strength setting 55 and per-cup quantity Î.

The selection line 5b shows symbols for drink selection.

The arrows in the navigation line 5c indicate the direction in which more menu levels can be found.

Please refer to “Displays” for more detailed information.

Start button

Press the start button 8 to begin drink preparation or to start a service programme.

Press the start button 8 again during drink preparation to stop the dispensing process prematurely.

j button and settings

Use the j button 7 to display information

(press briefly) and adjust settings (hold down for at least 3 seconds).

Displaying information

The following information can be displayed in the Info menu:

●●when should the next service be completed.

●●how many drinks have been dispensed since the espresso machine was switched on.

●●Press the j button 7 briefly and navigate with the < and > buttons 4.

INFO
DESCALE AFTER.	200 À
CLEAN AFTER	200 À	*
CHANGE FILTER IN	200 À	*
INFO
NO. OF COFFEES	11
NO. OF MILK MIXES	15
AMOUNT HOT WATER	2L

*appears only if the filter is activated.

Press the j button 7 briefly to return to the drink selection. If no button is pressed for about 10 seconds, the appliance automatically switches back to drink selection mode.

Adjusting settings

See “Menu settings”.

TES80.. | 04/2013

TES803_805_807_1RW.indb 7

08.05.2013 14:52:58

Adjusting the grinding unit

The rotary selector 17 adjusts the grind settings from coarse to fi ne.

¡ Warning!

Adjust the grinding unit only while it is running! Otherwise the appliance may be damaged. Do not reach into the grinding unit.

●While the grinding unit is running, adjust the rotary selector 17 from fi ne (a: Turn anticlockwise) to coarse (b: Turn clockwise).

Info: The new setting will not become apparent until after the second cup of coffee.

Note: If the message PLEASE ADJUST

GRINDING UNIT TO COARSER SETTING! appears in the display, the grind setting for the coffee beans is too fi ne. Adjust the grinding unit to a coarser setting.

Tip: For dark roast coffee beans, choose a fi ner grind; for lighter beans a coarser grind.

ONLY TES807

Cup warming function

¡ Warning!

The cup warmer 27 gets very hot!

The fully automatic espresso machine has a cup warmer 27 that can be switched on or off manually with button 28. When the cup warmer 27 is on, button 28 lights up.

Tip: For optimal cup warming, place the base of the cups on the cup warmer 27.

Displays

Display messages

Various messages are shown in the display 5.

Information (only TES807)

For example:

	ESPRESSO	ËË Í
	WATER TANK
	ALMOST EMPTY
Prompts
For example:
	ESPRESSO	ËË Í

REFILL WATER TANK

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 8

08.05.2013 14:52:58

Display settings

Press the selection buttons < and > 4 to select the following selection menus in the menu levels:

Drink selection
ESPRESSO	Ë Í

Â Ã À Á Å Æ

Coffee strength (only for coffee drinks)

	ESPRESSO			Ë Í

		5	55	555


Per-cup quantity
	ESPRESSO			Ë Í

		Î	Ð	Ò

Select your personal per-cup quantity

ESPRESSO

Ë Í

Î ± 0 ml

My coffee (only TES807)
	MY COFFEE	Ë Í
	ESPRESSO	MILK
	40%

Turn the rotary knob 6 to adjust the following parameters within the menus:

Settings – Drink selection:

Â 2 X ESPRESSO

Ã2 X COFFEE

À ESPRESSO

ÁCOFFEE

ÄCAFFE LATTE (only TES807)

Å MACCHIATO

ÆCAPPUCCINO

ÇMY COFFEE (only TES807)

ÈMILK FROTH

ÉWARM MILK

ÊHOT WATER

Settings – Coffee strength:

åVery mild

ååMild

ååå Normal

äStrong

ãVery strong

2x å	aromaDouble	Shot strong
2x ååå	aromaDouble	Shot strong +
2x ã aromaDouble		Shot strong ++

aromaDouble Shot:

The longer the coffee is brewed, the more bitter substances and undesired

Aromas are released. This has a negative effect on the taste and makes the coffee less easily digestible. So for extra strong coffee, the TES8.. has a special aromaDouble Shot function. When half the quantity has been prepared, coffee is ground and brewed again so that only the pleasant, Aromatic scents are released. The aromaDouble Shot function can be selected for all coffee drinks except for ESPRESSO À with a small per-cup quantity,

2 x ESPRESSO Â and 2 X COFFEE Ã.

TES80.. | 04/2013

TES803_805_807_1RW.indb 9

08.05.2013 14:52:58

Settings – Per-cup quantity

Îsmall

Ð medium

Òlarge

Settings – Personal per-cup quantity

The preset per-cup quantity Î, Ð or Ò can be individually adjusted to the size of the cup in use by turning the rotary knob 6. The per-cup quantity can be adjusted according to the drink selected. An arrow in the Ò symbol in the top right-hand corner of

the display indicates whether the per-cup quantity was increased or decreased. If you set for example COFFEE Á, the adjustment of the per-cup quantity in ml, and in the case of a milk-based coffee drink, for example CAPPUCCINO Æ, the adjustment of the per-cup quantity including the volume of milk (froth) in ml, is indicated.

Important: The selected amount in ml is an approximate value and can vary significantly as a result of crema forming, the grind setting or the type of milk used, etc.

Settings – My coffee (only TES807)

In addition to selecting coffee strength and per-cup quantity, you can choose the exact mix of espresso and milk for your own coffee setting MY COFFEE Ç:

●●The setting can be defined in 20 % steps by turning the rotary knob 6.

Customising

You can store up to 6 user profiles in the

USER SETTINGS menu. The required coffee and hot water temperatures are saved in the user profiles.

Important: The “Customising” settings (á button 2) are not identical to those under “Menu settings” (j button 7) and vice versa.

Storing or changing the user

●●Hold down the á button 2 for at least

3 seconds.

The menu appears:

USER SETTINGS

USER 1 START

USER 2

USER 3

●●Select the required user using the selection button and press the start button 8.

The following selection appears in the display:

USER SETTINGS:	USER 1

EDIT NAME	START
DELETE NAME
COFFEE TEMP.

●●To change the user name, use the selection button to go to EDIT NAME START and press the start button 8.

The input field appears in the display:

â ABCDEFGHIJKLMNOPQ

_ _ _ _ _ _

ABORT STORE

●●Turn the rotary knob 6 to select a letter or number.

●●Confirm by pressing the start button 8.

There are 6 characters available for the user name.

To delete entries made, select the symbol â and press the start button 8.

Note:

Press the selection button > to save your entry. Press the selection button < to cut the process short.

Info: The entry can be overwritten at any time.

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 10

08.05.2013 14:52:58

To delete the user, use the selection button DELETE NAME START and press the start button 8.

Saving temperatures

●●Use the selection button to select COFFEE TEMP. or HOT WATER TEMP..

●●Turn the rotary knob 6 to select the required setting.

●●Press the á button 2. The settings are saved.

AromaIntense (only TES807)

The intense flavour of the espresso or coffee may be adapted to individual requirements by setting the brewing speed.

●●Simply press the selection button AROMAINTENSE ESPRESSO or AROMAINTENSE COFFEE.

●●Finally, use the rotary knob 6 to select either normal brewing speed, e. g.

ESPRESSO STANDARD or slow brewing speed e. g. ESPRESSO INTENSIVE.

●●Press the á button 2. The settings are saved.

Calling up a user profile

●●Press the á button 2 briefly. The user profile menu appears:

SELECT A PROFILE

ROBERT USER 1 USER 2

●●Turn the rotary knob 6 to select a user profile and press the start button 8.

The drink selection menu appears:

●●Dispense a drink (see “Preparation using coffee beans”).

●●The selected settings are saved. ●●Press the á button 2 to exit the

customised menu.

Info: If you wish the appliance to exit the menu automatically, you can set this as described under “Menu settings – EXIT

PROFILE”.

Child-proof lock

The appliance can be locked to protect children from scalding and burning. ●●Hold down the à button 3 for at least

3 seconds.

The display 5 shows a key; the child-proof lock is activated.

ESPRESSO

Ë Í

It is no longer possible to operate the appliance.

ONLY TES807: The cup warmer 27 is switched off.

●●To deactivate the child-proof lock, hold down the à button 3 for at least

3 seconds. The key disappears from the display 5.

MACCHIATO Ë Í

ROBERT À Á Å Æ

●●Set the drink, coffee strength, etc. (see “Display settings”).

TES80.. | 04/2013

TES803_805_807_1RW.indb 11

08.05.2013 14:52:59

Menu settings

●●Hold down the j button 7 for at least

3 seconds.

The different setting options are now displayed.

SETTINGS

COFFEE TEMP.

HOT WATER TEMP. <85°C EXIT PROFILE

The different setting options can be selected with the selection buttons < and > 4.

Note: The changes you have made are saved automatically. It is not necessary to confirm them additionally. If no entry is

made after approx. 2 minutes, the menu will close automatically.

The following settings can be selected:

LANGUAGE

●●Turn the rotary knob 6 to select the required language.

AROMAINTENSE ESPRESSO (only TES807)

The intense flavour of the espresso may be adapted to individual requirements by setting the brewing speed.

●●Use the rotary knob 6 to select either normal brewing speed ESPRESSO STANDARD or slow brewing speed ESPRESSO

INTENSIVE.

Info: The brewing setting can also be selected for CAPPUCCINO and MACCHIATO. It makes no change to the milk froth.

AROMAINTENSE COFFEE (only TES807)

The intense flavour of the coffee may be adapted to individual requirements by setting the brewing speed.

●●Use the rotary knob 6 to select either normal brewing speed COFFEE STANDARD or slow brewing speed COFFEE INTENSIVE.

Info: The brewing setting can also be selected for CAFFE LATTE and MY COFFEE. It makes no change to the warm milk.

COFFEE TEMP.

●●Turn the rotary knob 6 to set the coffee temperature. The setting applies to all types of preparation, except the customised settings under “Customising”.

HOT WATER TEMP.

●●Turn the rotary knob 6 to set the temperature. The setting applies to all types of preparation except the customised settings under “Customising”.

EXIT PROFILE

●●Here you can set whether the appliance should exit the customising function automatically AUTOMATIC or manually

MANUALLY.

AUTO OFF AFTER

●●Turn the rotary knob 6 to enter the time span after which the appliance should automatically switch off following the last drink preparation.

A time between 5 minutes and 8 hours can be set.

CUP WARM. OFF IN (only TES807)

Here you can set the time span after which the cup warmer 27 switches off again automatically.

●●Set the required time by turning the rotary knob 6.

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 12

08.05.2013 14:52:59

CONTRAST

The display 5 contrast can be set from –10 to +10. The factory setting is +0.

●Turn the rotary knob 6 to select the required setting.

WATER HARDNESS

●Turn the rotary knob 6 to select the required water hardness 1, 2, 3 or 4.

Info: It is important to set the water hardness correctly, so that the appliance indicates accurately when the descaling programme should be run. The factory setting for the water hardness is 4.

You can check the water hardness using the enclosed test strip or by asking your local water supplier.

●Dip the test strip briefl y in water and check the result after one minute.

Level	Water hardness
	German (°dH)	French (°fH)
1	1-7	1-13
2	8-14	14-25
3	15-21	26-38
4	22-30	39-54

WATER FILTER

A new water fi lter 29 must be rinsed before it can be used.

●To do this, press the water fi lter 29 fi rmly into the water tank 11 with the aid of the measuring spoon 14. Fill the water tank with water up to the “max” mark.

●Turn the rotary knob 6 to select START and press the start button 8.

PLACE 1 L CONTAINER

PLACE SUCTION PIPE IN CONTAINER START

●Place a container with a capacity of 1litre under the milk frother 10.

●Place the end of the suction pipe 10d in the container.

●Press the start button 8. Water will now fl ow through the fi lter 29 to rinse it.

●Next, empty the container.

The appliance is ready for use again.

Info: Rinsing the fi lter 29 simultaneously activates the setting for the “change fi lter” display.

You can fi nd detailed information about the water fi lter in the enclosed fi lter instructions.

The fi lter 29 is no longer effective when the SERVICE - CHANGE FILTER display appears, or at the latest after two months. It needs to be replaced for reasons of hygiene and so that there is no build-up of limescale (this could damage the appliance).

Replacement fi lters can be obtained from retailers (TCZ7003) or from customer service (575491).

TES80.. | 04/2013

TES803_805_807_1RW.indb 13

08.05.2013 14:52:59

If no new filter 29 is used, turn the WATER FILTER setting to NO.

Info: If the appliance has not been used for a prolonged period (for example, when you are on vacation), the existing filter 29 should be rinsed before the appliance is used again. To do this, simply dispense a cup of hot water.

TRANSPORT. LOCK

●●To avoid damage caused by frost during transport and storage, the appliance must be completely emptied first.

Info: The appliance must be ready for use and the water tank 11 filled.

●●Press the start button 8. The appliance automatically empties the pipe system and switches off.

●●Empty the water tank 11 and the drip tray 23.

FACTORY RESET

You can cancel your own settings and reset the factory settings.

●●To activate the factory settings, press the start button 8.

Info: The appliance can also be reset to the factory settings using a combination of buttons. The appliance must be switched off fully.

●●Hold down the selection buttons < and > 4 and the on/off switch 1 O / I at the same time for at least 5 seconds. Press the start button 8. The factory settings are now reactivated.

Preparation using coffee beans

This fully automatic espresso machine grinds beans freshly for each brew. If possible, use only beans for fully automatic coffee and espresso machines. For optimal quality, deep-freeze the beans or store in a cool place in sealed containers. Coffee beans can be ground while frozen.

Important: Fill the water tank 11 with cold, fresh water every day. The water tank 11 should always contain sufficient water for operating the appliance.

Tip (only TES807): Pre-warm cups, especially small, thick espresso cups, on the cup warmer 27.

Different coffee drinks can be prepared quite simply at the press of a button.

Note: With some settings, the coffee is prepared in two stages (see

“aromaDouble Shot”). Wait until the procedure is fully completed.

Drink preparation without milk

The appliance must be ready for use. ●●Place the pre-warmed cup(s) under the

coffee outlet 9.

●●Select the required 2 X ESPRESSO Â, 2 X COFFEE Ã, ESPRESSO À or COFFEE Á by turning the rotary knob 6.

The display 5 shows the selected drink along with the setting for coffee strength and per-cup quantity for this drink.

ESPRESSO Ë Í

Â Ã À Á Å Æ

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 14

08.05.2013 14:52:59

You can change the settings (see “Display settings”) or call up and customise settings

(see “Customising”). ●●Press the start button 8.

The coffee is brewed and then dispensed into the cup(s).

Drink preparation with milk

The appliance must be ready for use. ●●Place the suction pipe 10d of the milk

frother 10 deep in the milk container 26. ●●Swivel the coffee outlet 9 to the right until

it clicks into place.

●●Place the pre-warmed cup or glass under the coffee outlet 9 and milk frother 10.

●●Select the required CAFFE LATTE Ä (only

TES807), MACCHIATO Å, CAPPUCCINO Æ or MY COFFEE Ç (only TES807) by turning the rotary knob 6.

The display 5 shows the selected drink along with the setting for coffee strength and per-cup quantity for this drink.

CAPPUCCINO

Ë Í

À Á Å Æ È É

You can change the settings (see “Display settings”) or call up and customise settings

(see “Customising”).

●●Press the start button 8.

First milk is delivered into the cup or glass.

Then the coffee is brewed and dispensed into the cup or glass.

Important: Dried milk residue is difficult to remove, so the milk frother 10 must be cleaned with lukewarm water immediately after use (see “Cleaning the milk system”).

Preparation using ground coffee

This fully automatic espresso machine can also be operated using ground coffee (not instant coffee powder).

Note: The aromaDouble Shot function cannot be used when coffee is prepared using ground coffee.

Drink preparation without milk

The appliance must be ready for use. ●●Place the pre-warmed cup(s) under the

coffee outlet 9.

●●Select the required 2 X ESPRESSO Â, 2 X COFFEE Ã, ESPRESSO À or COFFEE Á by turning the rotary knob 6.

●●Open the powder compartment 18. ●●Pour in no more than 2 level measuring

spoons 14 of ground coffee.

¡¡ Warning!

Do not use whole beans or instant coffee.

●●Close the powder compartment 18. ●●Press the start button 8.

The coffee is brewed and then dispensed into the cup(s).

Note: Repeat the procedure for another cup of coffee. If coffee is not dispensed within

90 seconds, the brewing chamber empties automatically to avoid an overflow. The appliance rinses.

TES80.. | 04/2013

TES803_805_807_1RW.indb 15

08.05.2013 14:52:59

Drink preparation with milk

The appliance must be ready for use. ●●Place the suction pipe 10d of the milk

frother 10 deep in the milk container 26. ●●Swivel the coffee outlet 9 to the right until

it clicks into place.

●●Place the pre-warmed cup or glass under the coffee outlet 9 and milk frother 10.

●●Select the required CAFFE LATTE Ä (only

TES807), MACCHIATO Å, CAPPUCCINO Æ or MY COFFEE Ç (only TES807) by turning the rotary knob 6.

●●Open the powder compartment 18. ●●Pour in no more than 2 level measuring

spoons 14 of ground coffee.

¡¡ Warning!

Do not use whole beans or instant coffee.

●●Close the powder compartment 18. ●●Press the start button 8.

First milk is delivered into the cup or glass.

Then the coffee is brewed and dispensed into the cup or glass.

Important: Dried milk residue is difficult to remove, so the milk frother 10 must be cleaned with lukewarm water immediately after use (see “Cleaning the milk system”).

Note: Repeat the procedure for another cup of coffee / milk drink. If coffee is not dispensed within 90 seconds, the brewing chamber empties automatically to avoid an overflow. The appliance rinses.

Preparing milk froth and warm milk

¡¡ Risk of burns!

The milk frother 10 gets very hot. After use, allow to cool down first before touching.

The appliance must be ready for use. ●●Place the suction pipe 10d of the milk

frother 10 deep in the milk container 26. ●●Place the pre-warmed cup or glass under

the outlet of the milk frother 10.

●●Select the required setting MILK FROTH È or WARM MILK É by turning the rotary knob 6.

●●Press the start button 8.

Milk froth or warm milk flows from the outlet of the milk frother 10.

Press the start button 8 again to cut the process short.

Info: When preparing warm milk, you may hear a whistling sound. This is caused by the milk frother 10 for technical reasons.

Tip: For optimal milk froth quality, use cold milk with a fat content of at least 1.5 % if possible.

Important: Dried milk residue is difficult to remove, so the milk frother 10 must be cleaned with lukewarm water immediately after use (see “Cleaning the milk system”).

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 16

08.05.2013 14:52:59

Dispensing hot water

¡ Risk of burns!

The milk frother 10 gets very hot. After use, allow to cool down fi rst before touching.

The appliance must be ready for use.

●Place the pre-warmed cup or glass under the outlet of the milk frother 10.

●Select the required setting for HOT WATER Ê by turning the rotary knob 6.

●Press the start button 8.

PLEASE REMOVE SUCTION HOSE START

●Remove the milk suction hose 10c and press the start button 8.

Hot water runs out of the milk frother outlet 10.

Press the start button 8 again to cut the process short.

Note: It is possible to set the temperature of the hot water (see “Menu settings”).

Maintenance and daily cleaning

¡ Danger of electric shock!

Unplug the appliance before cleaning it. Never submerse the appliance in water. Do not use a steam cleaner.

●Wipe the outside of the appliance with a soft, damp cloth.

●Do not use any cleaning agents that contain alcohol or spirits.

●Do not use abrasive cloths or cleaning agents.

●Always remove any limescale, coffee, milk, cleaning or descaling fl uid residue immediately. Such residue can cause corrosion. New sponge cloths may contain salts. Salts can cause rust fi lm on stainless steel and must therefore be washed out thoroughly before use.

●Pull the drip tray 23 with the coffee grounds container 23c forwards and out.

Remove the panel 23a and grate 23b. Empty and clean the drip tray and coffee grounds container.

K Do not put the following items in the dishwasher: Panel of drip tray 23a, powder compartment 18, brewing unit 20, water tank 11, Aroma cover 16 and stainless steel milk container.

J The following parts may be cleaned in the dishwasher: Drip tray 23, grate 23b, coffee grounds container 23c,

measuring spoon 14 and the individual parts of the milk container cover.

TES80.. | 04/2013

TES803_805_807_1RW.indb 17

08.05.2013 14:53:00

●Remove powder compartment 18 and rinse under running water.

● Wipe out the inside of the tray holders.

Important: Drip tray 23 and coffee grounds container 23c should be emptied and cleaned daily to prevent mould from developing.

Note: If the appliance is cold when switched on, or if it is switched off after dispensing coffee, it rinses automatically. In other words, the system cleans itself.

Important: If the appliance has not been used for a prolonged period of time (e.g. after a vacation), clean the entire appliance thoroughly, including the milk system 10 and brewing unit 20.

Cleaning the milk system

Important: The milk system 10 must be cleaned immediately after use!

The milk system 10 can be pre-cleaned automatically (see “Service programmes” or cleaned manually.

Dismantling the milk system 10 for cleaning:

●Pull the milk system 10 forward out of the appliance.

●Turn the upper part 10a in an anticlockwise direction and remove from the lower part 10b.

●Clean the individual parts with detergent solution and a soft cloth.

●Rinse all parts with clean water and dry.

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 18

08.05.2013 14:53:01

●Put all the parts back together. The milk frother can then be clicked back into place in the appliance.

Info: All parts of the milk frother 10 can also be put in the dishwasher.

Cleaning the brewing unit (Fig. F)

(refer also to the quick reference guide) In addition to the automatic cleaning programme, the brewing unit 20 should be removed regularly for cleaning.

●Switch the appliance off completely at the power on/off switch 1 O / I ; no buttons are lit.

●Take hold of the door to the brewing unit

19 at the bottom and open it.

●Slide the red lock 20a on the brewing unit

20 completely to the left.

●Press the red button 21, grasp the brewing unit 20 by the recessed grips and remove carefully.

●Remove the cover 20b of the brewing unit and rinse the brewing unit 20 thoroughly under running water.

●Thoroughly clean the brewing unit sieve under the running water.

Important: Clean the brewing unit without detergent and do not put it in the dishwasher.

●Wipe out the inside of the appliance thoroughly with a damp cloth and remove any coffee residues.

●Allow the brewing unit 20 and the inside of the appliance to dry.

●Replace the cover 20b on the brewing unit and reinsert the brewing unit 20 fully into the appliance.

●Slide the red lock 20a fully to the right and close the door 19.

TES80.. | 04/2013

TES803_805_807_1RW.indb 19

08.05.2013 14:53:02

Service Programmes

Tip: Refer also to the quick reference guide in the storage compartment 22.

At regular intervals, the display 5 shows the following texts:

SHORT RINSE MILK SYSTEM or SERVICE - DESCALE or SERVICE - CLEAN or

SERVICE - CALC‘NCLEAN.

The appliance should be cleaned or descaled immediately using the corresponding programme. You have the option of combining the processes DESCALING and CLEANING with the CALC‘NCLEAN function (see

“Calc‘nClean”). If the service programme is not run as instructed, the appliance may be damaged.

¡¡ Warning!

Follow the instructions for using the descaling and cleaning agents for each service programme. Never interrupt the service programme!

Do not drink the liquids!

Never use vinegar, vinegar-based products, citric acid or citric acid-based products! Never put descaling tablets or other descaling agents in the powder compartment 18!

Before starting the respective service programme (descaling, cleaning or Calc‘nClean), remove the brewing unit, clean as instructed and replace.

Specially developed and suitable descaling and cleaning tablets are available from retailers or customer service.

Accessories	Ordering number
	Retail	Customer
		service
Cleaning	TCZ6001	310575
tablets
Descaling	TCZ6002	310967
tablets

Cleaning the milk system

Duration: approx. 1 minute

CLEANING AND SERVICE

SHORT RINSE

MILK SYSTEM START

CALC‘NCLEAN

The milk system 10 can be pre-cleaned automatically.

●●Press the à button 3.

SHORT RINSE MILK SYSTEM START

●●Press the start button 8.

PLACE GLASS UNDER FROTHER, PLACE

SUCTION PIPE IN GLASS START

●●Place an empty glass under the milk system 10 and put the end of the pipe

10d in the glass.

●●Press the start button 8. The milk system is cleaned automatically.

●●Now empty the glass and clean the suction pipe 10d.

In addition to this, clean the milk system thoroughly at regular intervals (by hand or in the dishwasher).

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 20

08.05.2013 14:53:02

	en		21
Descaling			ADD 0.5 L WATER AND DESCALER START
Duration: approx. 30 minutes.			●●Pour lukewarm water into the empty water
	CLEANING AND SERVICE		tank 11 up to the “0.5 l” mark and then
	CLEANING AND SERVICE		dissolve two Bosch descaling tablets in it.
			dissolve two Bosch descaling tablets in it.
	DESCALE	START	●●Press the start button 8. The descaling
	CLEAN		programme will now run for about

20 minutes.

DESCALING

The start button 8 flashes while the different descaling processes are running.

The figures on the top right indicate the progress of the programme.

Important: If there is a water filter 29 in the water tank 11, it needs to be removed before the service programme is run.

●●Press the à button 3.

DESCALE START

●●Press the start button 8; the display 5 will guide you through the programme.

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it.

PLACE 1 L CONTAINER

PLACE SUCTION PIPE IN CONTAINER START

●●Place a container with 1 litre capacity under the milk frother 10.

●●Place the end of the suction pipe 10d in the container.

●●Press the start button 8.

REMOVE FILTER START

Info: If the water filter 29 is activated, the display will prompt you to remove the filter

29, then press the start button 8 again.

NOT ENOUGH DESCALING FLUID. REFILL FLUID START

Info: If there is not enough descaling solution in the water tank 11, the corresponding prompt is displayed. Pour in descaling solution and press the start button 8 again.

CLEAN AND REFILL WATER TANK START

●●Rinse the water tank 11 and refill it with fresh water up to the “max” mark.

●●Press the start button 8. The descaling programme now runs for about 1 minute and rinses the appliance.

DESCALING

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it.

Replace the filter if one is being used. The appliance is ready for use again.

Important: Wipe down the appliance using a soft, damp cloth to immediately remove any descaler residue. Such residue can cause corrosion. New sponge cloths may contain salts. Salts can cause rust film on stainless steel and must therefore be washed out thoroughly before use.

Thoroughly clean the suction pipe 10d of the milk frother.

TES80.. | 04/2013

TES803_805_807_1RW.indb 21

08.05.2013 14:53:02

Cleaning

Duration: approx. 8 minutes.

CLEANING AND SERVICE

DESCALE
CLEAN	START

The start button 8 flashes while the different cleaning processes are running. The figures on the top right indicate the progress of the programme.

●●Fill the water tank 11 up to the “max” mark.

●●Press the à button 3.

CLEAN START

●●Press the start button 8; the display 5 will guide you through the programme.

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it.

The appliance is ready for use again.

Calc‘nClean

Duration: approx. 36 minutes.

Calc‘nClean combines the separate functions of descaling and cleaning.

If both programmes are due to be run soon, the espresso machine automatically

suggests this service programme.

CLEANING AND SERVICE

SHORT RINSE

MILK SYSTEM

CALC‘NCLEAN START

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it. The appliance rinses twice.

POSITION SWIVEL ARM

●●Swivel the coffee outlet 9 to the left until it clicks into place.

CLEANING

OPEN POWDER COMPARTMENT

●●Open the powder compartment 18.

INSERT BOSCH CLEANING TABLET

AND CLOSE DRAWER

●●Drop a Bosch cleaning tablet into the drawer 18 and close it.

PRESS START

●●Press the start button 8. The cleaning programme will now run for about

7 minutes.

CLEANING

The start button 8 flashes while the different Calc‘nClean processes are running. The figures on the top right indicate the progress of the programme.

Important: If there is a water filter 29 in the water tank 11, it needs to be removed before the service programme is run.

●●Press the à button 3.

CALC‘NCLEAN START

●●Press the start button 8; the display 5 will guide you through the programme.

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it.

●●Swivel the coffee outlet 9 to the right until it clicks into place.

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 22

08.05.2013 14:53:02

PLACE 1 L CONTAINER

PLACE SUCTION PIPE IN CONTAINER START

●●Place a container with a capacity of at least 1 l under the milk frother 10.

●●Place the end of the suction pipe 10d in the container.

●●Press the start button 8. The appliance rinses twice.

CLEANING

OPEN POWDER COMPARTMENT

●●Open the powder compartment 18.

INSERT BOSCH CLEANING TABLET

AND CLOSE DRAWER

●●Drop a Bosch cleaning tablet in the drawer 18 and close.

REMOVE FILTER START

Info: If the water filter 29 is activated, the display will prompt you to remove the filter

29, then press the start button 8 again.

ADD 0.5 L WATER AND DESCALER START

●●Pour lukewarm water into the empty water tank 11 up to the “0.5 l” mark and then dissolve two Bosch descaling tablets in it. ●●Press the start button 8. The descaling

programme now runs for about

20 minutes.

DESCALING

NOT ENOUGH DESCALING FLUID. REFILL FLUID START

Info: If there is not enough descaling solution in the water tank 11, the corresponding prompt is displayed. Pour in descaling solution and press the start button 8 again.

CLEAN AND REFILL WATER TANK

START

●●Rinse the water tank 11 and refill it with fresh water up to the “max” mark.

●●Press the start button 8. The descaling programme now runs for about 1 minute more, followed by the cleaning programme for about 7 minutes, and rinses the appliance.

DESCALING

CLEANING

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it.

Replace the filter if one is being used. The appliance has completed descaling and cleaning and is ready for use again.

thoroughly before use.

Thoroughly clean the suction pipe 10d of the milk frother.

Note: If one of the service programmes is interrupted, e. g. by a power outage, proceed as follows:

●●Rinse the water tank 11 and refill it with fresh water up to the “max” mark.

●●Press the start button 8. The cleaning programme now runs for about 3 minutes, and rinses the appliance.

CLEANING

EMPTY DRIP TRAY

REPLACE DRIP TRAY

●●Empty the drip tray 23 and reinsert it.

The appliance is ready for use again.

TES80.. | 04/2013

TES803_805_807_1RW.indb 23

08.05.2013 14:53:03

Tips on energy saving

●●The display has a dimming function that switches on automatically when the appliance is not in use. The display is illuminated dimly. Press any button or the rotary knob to brighten the display illumination again.

●●If the appliance is not being used, switch it off at the power on/off switch 1 O / I on the front.

●●If possible, do not interrupt coffee or milk froth dispensing. Stopping a process prematurely results in higher energy consumption and the drip tray fills up more quickly.

●●Descale the appliance regularly to avoid a build-up of limescale. Limescale residue results in higher energy consumption.

Frost protection

¡¡ To avoid damage caused by frost during transport and storage, the appliance must be completely emptied first.

See “Menu settings – TRANSPORT. LOCK.”

Storing accessories

The espresso machine has special compartments for storing the accessories and quick reference guide inside the appliance. ●●To store the measuring spoon 14, remove the water tank 11 and insert the spoon in

the shaped recess 13.

●●To store the quick reference guide, open the door to the brewing unit 19 and stow away the quick reference guide in the storage compartment 22 provided for this purpose.

Accessories

The following accessories are available from retailers or from customer service:

Accessories	Ordering number
	Retail	Customer
		service
Cleaning tablets	TCZ6001	310575
Descaling tablets	TCZ6002	310967
Water filter	TCZ7003	575491
Care set	TCZ7004	570351
Milk container with	TCZ8009	576165
“Fresh Lock” lid

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 24

08.05.2013 14:53:03

Disposal A

Dispose of packaging in an environmen- tally-friendly manner. This appliance is labelled in accordance with European Directive 2012/19/EG concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU. Please ask your specialist retailer about current disposal facilities.

Technical specifications

Guarantee

The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

Changes reserved.

Power connection (voltage/frequency)	220-240 V / 50-60 Hz
Heater wattage	1600 W
Maximum static pump pressure	19 bar
Maximum water tank capacity (without filter)	2.4 l
Maximum capacity of the coffee bean container	~300 g
Length of power cable	100 cm
Dimensions (H x W x D)	385 x 301 x 458 mm
Weight, empty	10–12 kg
Type of grinding unit	Ceramic

TES80.. | 04/2013

TES803_805_807_1RW.indb 25

08.05.2013 14:53:03

26 en

Simple troubleshooting

Problem	Cause	Solution
Display shows	Beans are not falling into	Gently tap the bean container 15.
REFILL BEAN CONTAINER	the grinding unit (beans too	Change the type of coffee if
although the bean	oily).	necessary . When the bean
container 15 is full, or the		container 15 is empty, wipe it
grinding unit does not		with a dry cloth.
grind the beans.

No tea water dispensed. The milk frother 10 or its holder is soiled.

Clean the milk frother 10 or its holder (see “Cleaning the milk system”).

Too little or no milk froth,	The milk frother 10 or its
or the milk frother 10 does	holder is soiled.
not draw the milk in.

Clean the milk frother 10 or its holder (see “Cleaning the milk system”).

Milk unsuitable for frothing. Use low-fat milk (1.5 % fat).

The milk frother 10 is not correctly assembled.

Moisten and assemble the milk frother parts.

	Build-up of limescale in the	Descale the appliance using two
	appliance.	descaling tablets, if necessary
		repeat the procedure.
The selected per-cup	Coffee is ground too finely.	Adjust the grinding unit to a
quantity is not reached.	Pre-ground coffee is too	coarser setting. Use coarser pre-
Coffee dispensing slows	fine.	ground coffee.
to a trickle or stops	Build-up of limescale in the	Descale the appliance.
completely.	appliance.
Coffee has no “crema”.	Unsuitable type of coffee.	Use a type of coffee with a
		higher proportion of robusta
		beans.
	The beans are no longer	Use fresh beans.
	fresh.
	The grinding setting is not	Adjust the grinding setting to
	suitable for the beans.	fine.
Coffee is too “acidic”.	The grinding setting is too	Adjust the grinding unit to a finer
	coarse or the pre-ground	setting or use finer pre-ground
	coffee is too coarse.	coffee.
	Unsuitable type of coffee.	Use a darker roast.
Coffee is too “bitter”.	The grind setting is too fine	Adjust the grinding unit to a
	or the pre-ground coffee is	coarser setting or use coarser
	too fine.	pre-ground coffee.
	Unsuitable type of coffee.	Change the type of coffee.

If you are unable to solve the problem, always call the hotline.

You will find the telephone numbers at the back of these instructions.

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 26

08.05.2013 14:53:03

+ 138 hidden pages