Bosch TES60321RW User Manual [ru]

0 (0)

Moodpic 1 63,2 x 50,25mm CMYK & GREY

Moodpic 2 98,6 x 46,7mm CMYK & GREY

TES 603.. / TES 605.. / TES 607..

en	Instruction manual	pl	Instrukcja obsługi
fr	Mode d’emploi	cs	Návod k použití
nl	Gebruiksaanwijzing	ru	Инструкция по эксплуатации

en	English	2
fr	Français	26
nl	Nederlands	52
pl	Polski	77
cs	Čeština	103
ru	Pycckий	127
A	Included in delivery (see page 5)
	Contenu de l’emballage (voir page 29)
	Leveringsomvang (zie pagina 55)
	Zakres dostawy (patrz strona 80)
	Součást dodávky (viz strana 106)
	Объем поставки (см. стр. 130)
	A	B
		C

E-Nr. ……… FD… …

D E F

C
	10
	11
	9
6
5	12
2
3	13
4

D	8

E	F	17a	17c

17d*

4c	17b
	17b
4d

14b 16

14a

Dear Coffee Connoisseur,

Congratulations on purchasing this fully automatic coffee machine from Bosch.

This instruction manual describes a number of versions of the appliance with minor differences.

Please also take note of the enclosed Quick reference guide, which you can then keep in the specially provided compartment 16 until you need it again.

How to use these instructions:

You can open up the front cover of this instruction manual to see illustrations of the appliance with each part numbered. These numbers will be referred to throughout the text.

Example: brewing unit 14

These instructions also show display texts and symbols in a special way so that you can clearly see where we refer to texts displayed by the appliance or symbols that are marked on it.

Example of display texts: Espresso Example of control elements: R

Contents

Safety instructions 3 Included in delivery 5 Overview 5 Overview of control elements 6 Display 7 Initial use 8 Childproof lock 9 Preparing drinks 9

Preparing coffee drinks.............................		11
Preparation using milk		11
Preparation using ground coffee ..............		12
Dispensing hot water		12
Adjusting the grind setting		13
Menu		13
Care and daily cleaning		16
Cleaning the milk system		17
Cleaning the brewing unit (Figure G)		18
Service programmes		19
Cleaning the milk system		19
Descaling	19
Cleaning	20
calc‘nClean	21
Tips on energy saving		22
Frost protection		22
Storing accessories		22
Accessories		22
Disposal		22
Guarantee		22
Simple troubleshooting		23
Technical specifications		25

Safety instructions

Please read and follow the operating instructions carefully and keep them for later reference Enclose these instructions when you give this appliance to someone else This appliance is designed for the preparation of normal household quantities in the home, or in household-like, non-commercial environments Household-like environments include staff kitchens in shops, offi ces, agricultural and other small businesses or for use by guests at bed-and-breakfast establishments, small hotels and similar residential facilities

¡ Danger of electric shock!

The appliance may only be connected to a power supply with alternating current via a correctly installed socket with earthing. Ensure that the protective conductor system of the domestic supply has been correctly installed. Connect and operate the appliance only according to the type plate specifi cations. To avoid potential hazards, repairs such as replacing a damaged cable must only be carried out by our customer service personnel.

This appliance can be used by children aged from 8 years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Keep children under 8 years of age away from the appliance and connecting cable and do not allow them to use the appliance. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.

Never immerse the appliance or mains cable in water. Use only if power cord and appliance show no signs of damage. Should a fault occur, pull the plug or disconnect from the mains immediately.

The appliance contains permanent magnets that may infl uence electronic implants such as pacemakers or insulin pumps. Persons with electronic implants should keep a minimum of 10 cm away from the front of the appliance.

¡ Risk of suffocation!

Do not allow children to play with packaging material. Store small parts safely as they can be easily swallowed.

¡ Risk of injury!

Do not reach into the grinding unit. A misuse of the appliance can potentially lead to injury.

¡ Risk of burns!

The milk system becomes extremely hot. After use, allow to cool down fi rst before touching. After the use the heating element surfaces and warming plate can be subjected to residual heat.

Included in delivery

(Figure A on the fold-out pages)

A Fully automatic coffee machine	D Milk tube and suction pipe
B User Manual	E Water hardness testing strip
C Quick reference guide	F Measuring spoon

Overview

(Figures B, C, D, E, F and G on the fold-out pages)

1	Mains switch J	11	Dial selector for grinding level
2	Control panel (see next page)	12	Drawer
3	Display		(for ground coffee/cleaning tablet)
4	Drinks outlet (coffee, milk, hot water),	13	Door to brewing unit
	height-adjustable	14	Brewing unit
	a) Cover		a) Locking mechanism
	b) Milk system /coffee outlet (two-part)		b) Cover
	c) Milk tube	15	Eject lever
5	d) Suction pipe	16	Storage compartment
5	Removable water tank		for quick reference guide
6	Lid for water tank	17	Drip tray
7	Storage compartment for measuring		a) Drip tray panel
	spoon		b) Drip plate
8	Measuring spoon		c) Coffee grounds container
9	(insertion aid for water filter)	18	d) Floater *
9	Bean container	18	Compartment for power cord
10	Aroma cover	19	Rating plate (E number, FD)

* These user instructions describe a number of appliance versions. Items marked * are not present in all models.

Overview of control elements

(Figure B on the fold-out pages)

FFThe following symbols are visible or backlit depending on the appliance’s current operating mode:

			Espresso						Coffee

			Cappuccino						Latte Macchiato




			Caffe Latte						R– Start/stop button

			Milk froth / Hot water						F– Back

			G– Dispense two cups						H– Set coffee strength
			simultaneously						H– Set coffee strength
			simultaneously

			B– Confirm / Store						A– Open menu

									E– Service program
			D– Select cup size						for milk system (touch briefly)
									and childproof lock (touch for at
									least 3 seconds).

Mains switch J

The mains switch Jis used to switch the appliance on or off. The appliance rinses itself automatically when it is switched on and off.

The appliance does not rinse if:

●●it is still warm when switched on, or ●●no coffee was dispensed before it was

switched off.

The appliance is ready for use when the symbols and the display on the control panel are lit.

Control panel (touch field)

In the control panel you can easily navigate the controls just by touching the symbols and buttons.

You will hear an audible signal.

These audible signals can be switched on or off (see the section “Menu – Key tones”).

Drink selection

Touching the corresponding symbol selects the desired drink (see the section “Preparing drinks”).

Start/stop button

Touching Reither begins preparing a drink or launches a service programme. If you touch R again while the drink is being prepared, dispensing will be prematurely halted.

Touching Acalls up the menu, the navigation symbols will be activated and light up. Touch I, Band Fto navigate through the menu and call up information or change settings (see the section “Menu”).

Drink options

Touching Hor Dadjusts the strength or size of the drink, touching Gprepares two cups simultaneously as soon as you touch Rto begin dispensing (see the section “Preparing drinks”).

milk clean and childproof lock

Briefly touching Ecalls up the cleaning programme for the milk system (see the section “Daily maintenance and cleaning – Cleaning the milk system”).

Touching Efor 3 seconds or more activates or deactivates the childproof lock (see the section “Childproof lock”).

Display

The display shows the selected drinks and settings plus messages reporting the appliance’s operating status.

Espresso

regular

medium

Please refill water tank

These messages are cleared as soon as the action has been carried out.

Initial use

General

Fill the appropriate container using only pure, cold, uncarbonated water and solely roasted beans. Do not use coffee beans that have been glazed, caramelised or treated with other additives containing sugar, since they will block the brewing unit. The water hardness setting on the appliance can be adjusted. The factory setting for the water hardness is 4. Use the enclosed test strip to determine the hardness of your water supply. If this shows a value other than 4, you will need to programme the appliance appropriately after it has been taken into service (see section “Menu – Water hardness”).

Setting up the appliance

●●Remove any protective plastic film.

●●Place the fully automatic coffee machine on a level, waterproof surface that is able to support its weight.

●●The appliance’s ventilation slits must not be covered or obscured.

FFImportant: Only use the appliance in a frost-free room. If it has been transported or stored at temperatures below 0°C, wait at least 3 hours before taking it into operation.

●●Connect the power supply (cable storage compartment 18) to the socket. You can adjust the length of the cable by pulling it further out or pushing it back in. To do this, place the appliance with its back flush with the edge of the work surface and either pull the cable out downwards or push it in upwards.

●●Flip up the lid of the water tank 6.

●●Remove the water tank 5, rinse it out and fill it with fresh cold water. Do not fill it past the “max” mark.

●●Replace the water tank 5, making sure that it is straight, and push it right down into place.

●●Reclose the lid of the water tank 6.

●●Fill the bean container 9 with coffee beans. ●●Use the main switch J1 to switch on the

appliance.

The control panel and the display will be activated. The display will show the previously specified language, which will also be used for all subsequent display

texts. A number of different languages are available.

●●Touch Irepeatedly until the display indicates the desired language.

Deutsch

English

Français

●●Touch Rto confirm your selection.

The chosen language is now stored.

The brand logo will light up on the display 3. The appliance will heat up and rinse itself, a small amount of water will run out of the drink outlet 4.

The appliance is ready for use when the symbols and the display on the control panel are lit.

FFThe factory settings of the fully automatic coffee machine are programmed for optimal performance. The appliances switches off automatically after a configured time (see the section “Menu – Automatic shut-down”).

FFWhen the appliance is used for the first time, after a service program has been run and when it has not been operated for a long period, the first beverage will not have the full aroma and should not be consumed.

FFWhen the fully automatic coffee machine is first used, you will achieve a suitably thick and stable “crema” only after the first few cups have been dispensed.

FFIf the appliance is in use for a long period of time, water droplets will form on the ventilation slits. This is normal.

Childproof lock

The appliance can be locked to protect children against scalding and burns. ●●Touch Efor at least 3 seconds. A key symbol appears on the display 3. The childproof lock is now active.

It is no longer possible to operate the appliance.

●●Touch Efor at least 3 seconds. The key symbol disappears from the display 3. The childproof lock is now deactivated . The appliance can be used in the usual way.

Preparing drinks

This fully automatic coffee machine grinds fresh beans for every brewing. For optimum quality, store the beans in a cool place in sealed containers.

FFImportant: Fill the water tank 5 with fresh clean water every day. The tank 5 should always contain sufficient water for operating the appliance.

FFCups should be prewarmed, e.g. with hot water. This applies particularly to small thick-walled espresso cups.

FFFor a number of settings, coffee is prepared in two stages (see “aromaDouble Shot”). Please wait until the process is completely finished.

FFIf no controls are activated for a period of one minute the appliance will automatically exit from settings mode. The previously made settings will automatically be stored.

Different beverages can be prepared just by touching a key.

Drink selection

Touching the appropriate button, e.g. Espresso, selects the desired drink; Espresso will light up. The name of the drink and the currently active values for strength and cup size are shown in display 3.

You can choose from the following drinks:

Espresso	Caffe Latte
Coffee	Milk froth
Cappuccino	Warm milk
Latte Macchiato	Hot water

Adjusting the strength, selecting ground coffee

Touch Hto set the strength of your coffee individually or to specify that ground coffee is to be used.

The following settings are possible:

very mild	very strong
mild	doubleshot strong
regular	doubleshot strong+
strong	Ground coffee

●●Touching the appropriate symbol selects the desired drink.

●●Touch Hrepeatedly until the desired setting e.g. strong or Ground coffee (see the section “Preparation using ground coffee”) appears on the display.

aromaDouble Shot

The longer the coffee is brewed, the more bitter substances and undesired aromas are released. This has a negative effect on the taste and makes the coffee less easily digestible. So for extra strong coffee, the appliance has a special aromaDouble Shot function. When half the quantity has been prepared, it grinds and brews fresh coffee beans so that only the pleasant, aromatic scents are released.

FFThe aromaDouble Shot function can be selected for any drink containing a proportion of at least 35 ml coffee volume. It is not available for small drinks such as a small espresso or when the Gsetting is enabled.

Select cup size

Touching Dselects the volume of coffee desired.

The following settings are possible:

small

medium

large

●●Touching the appropriate symbol selects the desired drink.

●●Touch Drepeatedly until the display indicates the desired setting.

FFAn arrow or multiple arrows next to the setting, e.g. „large ˆ“, indicate that the preset capacity (see the section “Menu – Set cup size”) has been changed.

Two cups at once

Once you have selected a black coffee or milky coffee drink (for some appliances, this applies only to black coffee), touching Gprepares two cups simultaneously as soon as you touch Rto begin dispensing. The setting is shown on the display.

●●Touching the appropriate symbol selects the desired drink.

●●Touch G.

●●Place two prewarmed cups at left and right underneath the beverage outlet 4.

●●Touch Rto begin dispensing the beverage.

The selected drink will be brewed and will then be dispensed into the two cups.

FFThe drink is prepared in two stages (two grinding operations). Please wait until the process is completely finished.

FFDepending on the type of appliance:

The function “Two cups at once” may be available only for black coffee, not for milky coffee drinks.

FFIf no controls are activated for a period of one minute the appliance will automatically exit from settings mode. The previously made settings will automatically be stored.

Preparing coffee drinks

The appliance must be ready for use.

●●Place a prewarmed cup underneath the beverage outlet 4.

●●Touch the appropriate symbol to select the desired drink, Espresso or Coffee.

The name of the drink and the currently active values for strength and cup size are shown in display.

Coffee

regular

medium

FFYou can change the cup size and coffee strength by touching Dand H. If you select Ground coffee, follow the procedure described under “Preparation using ground coffee”.

For example:

●●Touch Drepeatedly until the display shows large.

●●Touch Hrepeatedly until the display shows mild.

●●Touch Rto begin dispensing the beverage.

The coffee is brewed and then dispensed into the cup.

FFYou can touch Ragain to prematurely halt dispensing.

Preparation using milk

This fully automatic coffee machine possesses an integrated milk system that enables you to prepare coffee with milk or milk froth or warm milk alone.

BBRisk of burns!

The upper and lower sections of the milk system 4b become extremely hot. After use, always let them cool down before you touch them.

FFCaution!

Dried milk residues are difficult to remove, so you should always clean the appliance after each use (see the section “Cleaning the milk system”).

FFWhile milk is being prepared you may hear a whistling sound. This is due to the technical nature of the milk system 4b.

FFTouch Ragain to prematurely halt dispensing.

The appliance must be ready for use. The milk tube and suction pipe must be connected.

●●Insert the suction pipe 4d into the milk container.

●●Place a prewarmed cup or glass underneath the beverage outlet.

Coffee-based drinks with milk

●●Touch the appropriate symbol to select

Caffe Latte, Latte Macchiato or Cappuccino. The name of the drink and the previously specified values for strength and cup size are shown in display.

FFYou can change the cup size and coffee strength by touching Dand H. If you select Ground coffee, follow the procedure described under “Preparation using ground coffee”.

●●Touch Rto begin dispensing the beverage.

The milk or milk froth is dispensed into the cup or glass first. Then the coffee is brewed and runs into the cup or glass.

You can touch Ragain to prematurely halt dispensing of the milk or coffee, touching Rtwice stops the entire dispensing process.

Milk froth or warm milk

●●Touch the appropriate symbol to select

Milk froth or Warm milk.

●●Touch Rto begin dispensing the beverage.

Milk froth or warm milk is dispensed from the beverage outlet.

Preparation using ground coffee

This fully automatic coffee machine can also be operated using ground coffee (but not instant coffee).

FFWhen ground coffee is used the aromaDouble Shot function is not available.

The appliance must be ready for use.

●●Place a prewarmed cup underneath the beverage outlet 4.

●●Touch the appropriate symbol to select a black or milky coffee drink.

●●Touch Hrepeatedly until the display shows Ground coffee.

●●Open the ground coffee drawer 12.

●●Place no more than two level measuring spoons of ground coffee in the drawer.

FFCaution!

Do not place coffee beans or instant coffee in this drawer.

●●Close the ground coffee drawer 12. ●●Touch Rto begin dispensing

the beverage.

The coffee is brewed and then dispensed into the cup.

FFRepeat the procedure for another cup of coffee. If coffee is not dispensed within 90 seconds, the brewing chamber empties automatically to avoid an overflow. The appliance is then rinsed.

FFTouch Ragain to prematurely halt dispensing.

Dispensing hot water

Before hot water is dispensed the milk system should be cleaned and the milk tube removed (see the section “Cleaning the milk system”). If the milk system is not cleaned small amounts of milk may be dispensed together with the hot water.

BBRisk of burns!

The milk system 4b becomes extremely hot. After use, always let them cool down before you touch them.

The appliance must be ready for use.

●●Place a prewarmed cup underneath the beverage outlet 4.

●●Touch the symbol for Hot water. ●●Touch Rto begin dispensing

the beverage.

FFIf you see the message Please remove suction hose, proceed as follows:

●●Take off the milk tube 4c and then touch Ragain.

Hot water will flow out of the outlet 4.

FFTouch Ragain to prematurely halt dispensing.

Adjusting the grind setting

You can use the rotary selector 11 to adjust the grind setting from coarse to fine.

FFCaution!

Adjust the grind setting only while the grinding unit is running, otherwise you may damage the appliance.

AARisk of injury!

Do not reach into the grinding unit.

●●With the grinding unit running, adjust the selector 11 from fine (a: turn anticlockwise) to coarse (b: turn clockwise).

FFThe new setting will not become apparent until after the second cup of coffee.

FFFor dark roast coffee beans, choose a finer grind, for lighter beans a coarser grind.

The menu is used for changing individual settings, accessing information and launching processes.

●●Touch Ato open the menu. In the display you will see the various

setting options, the navigation symbols light up. The current setting is marked on the display.

Navigating through the menu:

I = move down

B = confirm / store

F = go back

A= open the menu / exit from the menu

FFTouching Idisplays each setting or selection option in order. After you reach the lowest menu item the topmost one is shown again.

For example:

Setting the coffee temperature to max. : ●●Touch A. The menu is opened. ●●Touch Irepeatedly until the display

shows Coffee temperature.

●●Touch B, the display shows e.g. high ●●Touch Irepeatedly until the display

shows max.

●●Touch Bto store the setting. The display shows the confirmation.

●●The menu item Coffee temperature appears.

●●Touch Fto exit from the menu.

FFAny changes you make will be discarded if no further entry is made for a period of about two minutes. The menu will then close automatically.

You can specify the following settings:

Set cup size

Set up the volume dispensed for each drink and each size of cup. The volumes set up in the factory can be adjusted stepwise.

●●Use Ito choose a drink and touch Bto confirm your choice.

●●Use Ito choose the desired volume and touch Bto confirm your choice.

The setting is then saved.

Languages

Setting up the language to be used for display texts.

●●Use Ito choose the desired language and touch Bto confirm your choice.

Water hardness

Set this to the hardness of the local water supply.

Level 1, 2, 3, 4 or Softening system can be selected. The preset level of water hardness is level 4.

●●Use Ito choose the desired water hardness and touch Bto confirm your choice.

FFIt is important to set the water hardness correctly, so that the appliance indicates accurately when the descaling programme should be run.

You can check the water hardness using the enclosed test strip or by asking your local water supplier. If a water softening system is installed in the house, please select the Softening system setting.

●●Briefly dip the test strip in the water and check the result after one minute.

Level	Water hardness
	German (°dH)	French (°fH)
1	1-7	1-13
2	8-14	14-25
3	15-21	26-38
4	22-30	39-54

Automatic shut-down

Setting how long the appliance should wait after the last drink was prepared before it automatically switches itself off.

You can specify values from 15 minutes to 8 hours. The factory setting is 30 minutes. ●●Use Ito choose the desired interval and touch Bto confirm your choice.

Coffee temperature

Specifying the temperature for coffee drinks and hot water.

You can choose normal, high, or max. The setting applies to all types of drink preparation.

●●Use Ito choose the desired temperature level and touch Bto confirm your choice.

Water filter

Specifying whether a water filter should be activated or whether no filter is used.

You can choose Activate new filter or No filter.

FFUsing a water filter can prevent the build-up of limescale.

Water filters are available from retail outlets or from customer services (see the section “Accessories”).

FFImportant: Before you can use a new water filter it will need to be rinsed.

●●Use the measuring spoon 8 to press the water filter firmly into the water tank 5.

●●Fill the water tank with water up to the “max” mark.

●●Connect the milk tube 4c to the milk system 4b and the suction pipe 4d.

●●Insert the end of the suction pipe 4d into the drip plate 17b.

●●Touch Aand use Ito select

Water filter.

●●Touch Band use Ito select

Activate new filter.

●●Empty the drip tray and re-insert. ●●Touch Bto confirm.

Water will now flow through the filter to rinse it.

●●Then empty the drip tray and re-insert. The appliance is ready for use again.

FFRinsing the filter simultaneously activates the setting for displaying the message “Please change water filter”. When this message appears, or at the latest after two months, the filter will no longer be effective. It needs to be replaced for reasons of hygiene and to prevent a build-up of limescale (which could damage the appliance).

If you do not intend to insert a new filter, select the setting No filter and touch B to confirm.

FFIf the appliance has not been used for a prolonged period (for example, while you are on holiday), the existing filter should be rinsed before the appliance is used again. To do this, simply dispense a cup of hot water.

Cleaning and care

Starting the special service programmes. You can select Rinse the milk system, Descale, Clean or calc’nClean.

●●Use Ito choose the desired programme and touch Bto confirm your choice.

●●Touch Rto begin running the programme.

FFImportant: Be sure to take note of the section on “Service programmes”.

Info Service programmes (depending on the type of appliance)

Display how many beverages can still be prepared before it will be necessary to run one of the service programmes.

●●Use Ito display Clean after --- cor

Descale after --- c.

●●Touch Fto exit from the display.

FFFor technical reasons the counter does not represent a precise number of cups.

Frost protection

Service programme to prevent frost damage during transportation and storage. This programme completely empties the appliance.

FFThe appliance must be ready for use and the water tank 5 must be filled.

●●Touch Rto begin running the programme.

●●Remove the water tank; the appliance automatically empties all its pipes and then switches itself off.

●●Empty the water tank 5 and the drip tray 17.

Key tones

Switches on or off the tones that you hear when you touch the control panel. ●●Touch Bto confirm your choice. ●●Use Ito choose Key tones ON

or Key tones OFF and touch Bto confirm your choice.

Beverage statistics

(depending on the type of appliance) Shows the volume of drinks dispensed since the appliance was taken into service. ●●Touch Fto exit from the display.

Factory settings

Resets your own settings to the condition when delivered.

●●Touch Rto clear all your own settings.

Care and daily cleaning

EERisk of electric shock!

Before cleaning the appliance, unplug it from the mains. Never immerse the appliance in water. Do not use a steam cleaner.

●●Wipe the outside of the appliance with a soft, damp cloth.

●●Clean the control panel with a microfibre cloth.

●●Do not use any cleaning agents containing alcohol or spirits.

●●Do not use abrasive cloths or cleaning agents.

●●Always immediately remove any limescale, or residues of coffee, milk, cleaning or descaling solution. It is possible for corrosion to form underneath such deposits.

●●New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be thoroughly rinsed before use.

●●Pull the drip tray 17 and coffee grounds container 17c towards the front and remove them. Take off the panel 17a and drip plate 17b. Empty and clean the drip tray and coffee grounds container.

●●Wipe out the inside of the appliance (holder, trays) and the drawer for ground coffee (this cannot be removed).

●●Remove the float 17d and clean it with a moist cloth (depends on the type of appliance).

LLDo not put the following parts in the dishwasher:

Panel of drip tray 17a, cover 4a, brewing unit 14, water tank 5 and aroma cover 10.

MMThe following parts may be cleaned in the dishwasher:

Drip tray 17, drip plate 17b, coffee grounds container 17c, measuring spoon 8 and the upper and lower parts of the milk system 4b.

FFImportant: The drip tray 17 and coffee grounds container 17c should be emptied and cleaned every day to prevent the formation of mould.

FFIf the appliance is cold when switched on, or if it is switched off after dispensing coffee, it rinses automatically. The system is therefore self-cleaning.

FFImportant: If at any time the appliance is not used for a lengthy period (e.g. holiday), clean the entire appliance thoroughly, including the milk system 4b and brewing unit 14.

Cleaning the milk system

AABe sure to clean the milk system 4b every time you make a drink involving milk!

You can clean the milk system 4b automatically using programme Eor by hand.

Automatic cleaning:

●●Touch Eand then R. ●●Place an empty glass under the beverage outlet 4 and stand the end of the suction

pipe 4d in it.

●●Touch Rto begin running the programme.

The milk system 4b will now clean itself automatically.

●●Then empty the glass and clean the suction pipe 4d.

Cleaning by hand:

BBRisk of burns!

The milk system 4b becomes extremely hot. After use, always let them cool down before you touch them.

Take the milk system 4b apart to clean it: ●●Push the beverage outlet 4 right down. ●●Take off the cover 4a towards the front

and pull off the milk tube.

●●Remove the milk system 4b by pulling it straight forward.

●●Take apart the upper and lower parts of the milk system 4b.

●●Separate the milk tube from the suction pipe.

●●Clean the individual parts with wash- ing-up liquid and a soft cloth.

●●Rinse all parts with clean water and dry them.

FFThe upper and lower parts of the milk system 4b, the milk tube 4c and the suction pipe 4d can also be cleaned in a dishwasher.

●●Reassemble the individual parts.

●●Place the milk system 4b back in the appliance from the front, making sure it is straight.

●●Replace the cover 4a.

Cleaning the brewing unit (Figure G)

FFSee also the Quick reference guide in the storage compartment 16.

In addition to the automatic cleaning programme, the brewing unit 14 should be removed regularly for cleaning.

●●Use the main switch J1 to switch the appliance completely off.

●●Open the door 13 to the brewing unit. ●●Slide the red latch 14a on the brewing

unit 14 all the way to the left.

●●Press the eject lever 15 right down. The brewing unit will be released.

●●Take hold of the brewing unit 14 by the recessed grips and carefully remove it.

FFImportant: Clean it without using washing-up liquid and do not put it in the dishwasher.

●●Remove the cover 14b and thoroughly clean the brewing unit 14 under running water.

●●Thoroughly clean the strainer of the brewing unit under the water jet.

●●Thoroughly clean the inside of the appliance with a moist cloth, removing any coffee residues.

●●Allow the brewing unit 14 and the inside of the appliance to dry.

●●Replace the cover 14b on the brewing unit and then push the brewing unit 14 back into the appliance until it latches into place.

●●Press the eject lever 15 right up.

●●Slide the red latch 14a all the way to the right and close the door 13.

Service programmes

FFSee also the Quick reference guide in the storage compartment 16.

Following prior notification, either

Descaling necessary or Cleaning necessary or calc’nClean necessary.

appears in display 3 at certain intervals. The unit should immediately be cleaned or descaled using the appropriate programme. The two processes Descale and Clean can optionally be carried out together using the calc’nClean function (see the section “calc’nClean”). Failure to carry out the

service programme according to the instructions may damage the appliance.

FFImportant: if descaling is not performed on the appliance in good time, then the following appears:

Descaling overdue. Appliance will soon be locked --> press menu for 3 sec.

Immediately perform the descaling process in accordance with the instructions. If the appliance is locked, it can only be operated again once the descaling process has been carried out.

FFCaution!

For each of the service programmes, use descaling and cleaning agents as described in the instructions. Never interrupt a service programme. Do not swallow any cleaning fluids! Never use vinegar, citric acid or any vinegar-based or citric acid-based agents. Never place descaling tablets or other descaling materials in the coffee drawer 12!

Before starting the service program (Descale, Clean or calc’nClean) remove the brewing unit, clean it as instructed and replace it.

Specially developed suitable descaling and cleaning tablets are available from retail outlets or from customer services (see the section “Accessories”).

Cleaning the milk system

Takes about 1 minute.

●●Touch Ato open the menu.

●●Use Ito choose Cleaning and care and touch Bto confirm your choice.

●●Use Ito choose Rinse the milk system and touch Bto confirm your choice.

●●Touch Rto begin running the programme.

FFThe milk system can also be cleaned by pressing E.

The display 3 will indicate the progress of the programme:

●●Place an empty glass under the beverage outlet 4 and stand the end of the suction pipe 4d in it.

●●Touch R. The milk system will now clean itself automatically.

●●Then empty the glass and clean the suction pipe 4d.

You should also regularly clean the milk system manually (dishwasher or by hand).

Descaling

Takes about 30 minutes.

The line at the bottom of the display indicates the progress of the descaling process.

FFIf there is a water filter in the water tank 5, be sure to remove it before starting the service programme.

●●Touch Ato open the menu.

●●Use Ito choose Cleaning and care and touch Bto confirm your choice.

●●Use Ito choose Descale and touch Bto confirm your choice.

●●Touch Rto begin running the programme.

The display 3 will indicate the progress of the programme:

●●Empty and re-insert the drip tray 17.

FFThe following request appears:

Remove water filter if inserted ¢start.

●●Remove the filter and then touch Ragain.

●●Pour lukewarm water into the empty water tank 5 up to the “0.5 l” mark and then dissolve one Bosch descaling tablet TCZ8002 in it. For the TCZ6002 you should always dissolve two tablets.

●●Touch R.

●●Place a container with a capacity of 0.5 litre under the beverage outlet 4.

●●Place the end of the suction pipe 4d in the container.

●●Touch R.

The descaling programme will now run for about 20 minutes.

FFIf there is not enough descaling solution in the water tank 5, you will see the prompt Refill descaler ¢start.

●●Add more descaling solution and then touch Ragain.

●●Rinse the water tank 5 and refill it with fresh water up to the “max” mark.

●●If you use a filter, replace it now. ●●Touch R.

The descaling programme will now run for about 1 minute and rinse the appliance. ●●Empty and re-insert the drip tray 17.

FFImportant: Wipe over the appliance with a soft damp cloth to ensure that you immediately remove any traces of descaling solution. It is possible for corrosion to form underneath such deposits. New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be thoroughly rinsed before use. Clean the suction pipe 4d of the drinks outlet particularly carefully.

The appliance has finished descaling and is ready for use again.

Cleaning

Takes about 9 minutes.

The line at the bottom of the display indicates the progress of the descaling process.

●●Touch Ato open the menu.

●●Use Ito choose Cleaning and care and touch Bto confirm your choice.

●●Use Ito choose Clean and touch Bto confirm your choice.

●●Touch Rto begin running the programme.

The display 3 will indicate the progress of the programme:

●●Empty and re-insert the drip tray 17. ●●Open the ground coffee drawer 12. ●●Drop one Bosch cleaning tablet in the

drawer 12 and close it. ●●Touch R.

The cleaning programme will now run for about 7 minutes.

●●Empty and re-insert the drip tray 17.

The appliance has finished cleaning and is ready for use again.

calc‘nClean

Takes about 43 minutes.

calc’nClean combines the functions Descale and Clean.

If both programmes are due to be carried out close together the fully automatic coffee machine will automatically suggest this service programme.

The line at the bottom of the display indicates the progress of the descaling process.

FFIf there is a water filter in the water tank 5, be sure to remove it before starting the service programme.

●●Touch Ato open the menu.

●●Use Ito choose Cleaning and care and touch Bto confirm your choice.

●●Use Ito choose calc’nClean and touch Bto confirm your choice.

●●Touch Rto begin running the programme.

The display 3 will indicate the progress of the programme:

●●Empty and re-insert the drip tray 17. ●●Open the ground coffee drawer 12. ●●Drop one Bosch cleaning tablet in the

drawer 12 and close it. ●●Touch R.

FFThe following request appears:

Remove water filter if inserted ¢start.

●●Remove the filter and then touch Ragain.

●●Pour lukewarm water into the empty water tank 5 up to the “0.5 l” mark and then dissolve one Bosch descaling tablet TCZ8002 in it. For the TCZ6002 you should always dissolve two tablets.

●●Touch R.

●●Place a container with a capacity of 1 litre under the beverage outlet 4.

●●Place the end of the suction pipe 4d in the container.

●●Touch R.

The descaling programme will now run for about 28 minutes.

FFIf there is not enough descaling solution in the water tank 5, you will see the prompt Refill descaler ¢start.

●●Add more descaling solution and then touch Ragain.

●●Rinse the water tank 5 and refill it with fresh water up to the “max” mark.

●●If you use a filter, replace it now. ●●Touch R.

The descaling programme will now run for about one more minute, and then the cleaning programme will run for about 7 minutes and rinse the appliance.

●●Empty and re-insert the drip tray 17.

The appliance has finished descaling and is ready for use again.

FFImportant: If any of the service programmes is ever interrupted, for instance by a power failure, please proceed as follows:

●●Rinse the water tank 5 and refill it with fresh water up to the “max” mark.

●●Touch R.

The appliance will be rinsed for approx. 2 minutes for safety reasons.

●●Empty and re-insert the drip tray 17.

The aborted service programme must be restarted.

Tips on energy saving

●●When the fully automatic coffee machine is not in use, use the mains switch J1 on the front of the appliance to switch it off.

●●In the menu, set the Automatic shut-down period to 15 minutes.

●●If possible, do not interrupt the dispensing of coffee or milk froth. Stopping a process prematurely results in higher energy consumption and the drip tray fills up more quickly.

●●Descale the appliance regularly to avoid a build-up of limescale. Limescale residues cause higher energy consumption.

Frost protection

FFCaution!

To prevent frost damage during transportation and storage, completely empty the appliance beforehand.

See the section “Menu – Frost protection”.

Storing accessories

The fully automatic coffee machine has special compartments to hold the measuring spoon and the Quick reference guide. ●●To store the measuring spoon 8, lift off the water tank 5 and place the spoon in

the preformed recess 7.

●●To store the Quick reference guide, open the door to the brewing unit 13 and insert the guide into the space provided 16.

Accessories

The following accessories are available from retailers or from customer service:

Accessories	Order number
	Retail /
	Customer service
Cleaning tablets	TCZ6001 / 00310575
Descaling tablets	TCZ8002 / 00576694
Water filter	TCZ7003 / 00575491
Care set	TCZ8004 / 00576331

Milk container with TCZ8009N / 00576166 “freshLock” lid

Disposal

Dispose of packaging in an environ-

J mentally-friendly manner. This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the framework for the return and recycling

of used appliances as applicable throughout the EU. Please ask your specialist retailer about current disposal facilities.

Guarantee

The guarantee conditions for this appliance are as defi ned by our representative in the country in which it is sold. Details regarding these conditions can be obtained from

the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

Changes reserved.

Simple troubleshooting

Problem	Cause	Solution
Coffee or milk froth quality	Build-up of limescale in the	Descale the appliance as
varies considerably.	appliance.	described in the instructions.

No hot water dispensed. The milk system or its holder is not clean.

Clean the milk system or its holder (see the section “Cleaning the milk system”).

Too little milk froth, or none at all, or the milk system is not taking in any milk.

The milk system or its	Clean the milk system or
holder is not clean.	its holder (see the section
	“Cleaning the milk system”).
Milk not suitable for	Do not use milk that has already
foaming.	been boiled. Use cold milk with a
	fat content of at least 1.5%.

The milk system is incorrectly assembled.

Moisten the upper and lower sections and fit them together.

	Build-up of limescale in the	Descale the appliance as
	appliance.	described in the instructions.
The selected per-cup	Coffee is being ground too	Adjust the grinding unit to a
quantity is not reached.	finely, or the pre-ground	coarser setting. Use a coarser
Coffee dispensing slows	coffee is too fine.	ground coffee.
to a trickle or stops	Heavy build-up of limes-	Descale the appliance as
completely.	cale in the appliance.	described in the instructions.
Coffee has no “crema”.	Unsuitable type of coffee.	Use a type of coffee with a
		higher proportion of robusta
		beans.
	The beans are no longer	Use fresh beans.
	fresh.
	The grinding setting is not	Adjust the grinding unit to a finer
	suitable for the beans.	setting.
Coffee is too “acidic”.	The grinding setting is too	Adjust the grinding unit to a finer
	coarse or the pre-ground	setting or use finer pre-ground
	coffee is too coarse.	coffee.
	Unsuitable type of coffee.	Use a darker roast.

Coffee is too “bitter”.

The grinding setting is toofine or the pre-ground coffee is toofine.

Adjust the grinding unit to a coarser setting or use coarser pre-ground coffee.

Unsuitable type of coffee. Change the type of coffee.

If you are unable to solve the problem, always call the hotline!

You will find the telephone numbers at the back of these instructions.

Problem	Cause	Solution
The coffee tastes “burnt”.	The brewing temperature is	Reduce the temperature,
	too high	see the section
		“Menu – Coffee temperature”.
	The grinding setting is	Adjust the grinding unit to a
	too fine or the pre-ground	coarser setting or use coarser
	coffee is too fine.	pre-ground coffee.
	Unsuitable type of coffee.	Change the type of coffee.
The water filter does not	The water filter is not	Firmly press the water filter
stay in position in the	mounted correctly.	straight down into the tank
water tank.		connection.
The coffee grounds are	The grinding setting is too	Adjust the grinding unit to a
not compact and are too	fine or too coarse, or not	coarser or finer setting, or use
wet.	enough ground coffee has	2 level measuring spoons of
	been used.	ground coffee.
Water dripped onto the	Drip tray was removed too	Wait a few seconds after the
inner floor of the appli-	soon.	last drink was dispensed before
ance when the drip tray		removing the drip tray.
was removed.
Display shows	Beans are not falling into	Gently tap the bean container.
Please refill bean container	the grinding unit (beans too	Possibly change the type of
although the container is	oily).	coffee used. When the bean
already full, or the grinder		container is empty, wipe it with a
is not grinding any beans.		dry cloth.
Display shows	Emptying is not detected	When the appliance is switched
Please empty drip tray	when the appliance is	on, remove and re-insert the
despite the drip tray being	switched off.	drip tray.
empty.	The drip tray is soiled.	Clean the drip tray thoroughly.
Display shows	Water tank wrongly	Insert water tank correctly.
Refill with still water or	inserted.
change filter	Carbonated water in the	Fill the water tank with fresh tap
	water tank.	water.
	Float is stuck in the water	Remove the tank and clean
	tank.	thoroughly.
	New water filter did not	Rinse the water filter according
	rinse according to the	to instructions and then switch
	instructions.	on.
	Air in the water filter.	Dip the water filter into water
		until no more air bubbles
		escape, replace the filter.
	Water filter is old.	Insert a new water filter.

If you are unable to solve the problem, always call the hotline!

You will find the telephone numbers at the back of these instructions.

		en

Problem	Cause	Solution
Display shows	Brewing unit is soiled.	Clean the brewing unit.
Please clean brewing unit,	Too much pre-ground	Clean the brewing unit. Place no
then replace	coffee in the brewing unit.	more than two level measuring
		spoons of ground coffee in the
		drawer.
	The mechanism of the	Clean the brewing unit (see the
	brewing unit is stiff.	section “Daily maintenance and
		cleaning”).
Display shows	Appliance is too warm.	Leave the appliance to cool
Please restart appliance		down.
	Brewing unit is soiled.	Clean the brewing unit.
Display shows	Appliance is too hot.	Switch off appliance for 30
Please let appliance		minutes.
cool down
Display shows	The appliance has a fault.	Please contact the hotline.
Error
Please contact hotline

If you are unable to solve the problem, always call the hotline!

You will find the telephone numbers at the back of these instructions.

Technical specifications

Power connection (voltage – frequency)	220–240 V – 50/60 Hz
Heater wattage	1500 W
Maximum static pump pressure	15 bar (TES603)
	19 bar (TES605 / TES607)
Maximum water tank capacity (without filter)	1.7 l
Maximum capacity of the coffee bean container	~300 g
Length of power cable	100 cm
Dimensions (H x B x D)	385 x 301 x 458 mm
Weight, empty	10–12 kg
Type of grinding unit	Ceramic

Chère amatrice de café, cher amateur de café,

nous vous félicitons pour l’achat de cette machine à espresso automatique Bosch.

Ce mode d’emploi décrit différents modèles de machines qui se distinguent par leur niveau d’équipement.

Veuillez également tenir compte de la notice succincte jointe. Un logement 16 a été prévu spécialement pour la conserver à portée de main dans la machine.

Comment utiliser ce mode d’emploi :

Vous pouvez rabattre la page de couverture de ce mode d’emploi vers l’avant. Vous y trouverez les illustrations de la machine avec les numéros auxquels il est fait constamment référence dans ce mode d’emploi.

Exemple : unité de percolation 14

Les symboles et les messages affichés sur l’écran sont également représentés de manière distincte dans ce mode d’emploi. Vous pourrez ainsi repérer plus facilement les messages et les symboles affichés ou apposés sur l’appareil.

Exemple de message affiché à l’écran :

Expresso

Exemple d’élément de commande :

Sommaire

Consignes de sécurité 27 Contenu de l’emballage 29 Vue d’ensemble 29 Vue d’ensemble –

Éléments de commande 30 Écran 31 Mise en service 32 Sécurité-enfants 33 Préparation des boissons 33

Préparation de boissons au café		35
Préparation de boissons lactées		35
Préparation avec du café moulu		36
Distribution d’eau chaude		37
Réglage du degré de mouture		37
Menu		38
Entretien et nettoyage quotidiens		41
Nettoyage du mousseur de lait		42
Nettoyage de l’unité de percolation
(figure G) ..................................................		43
Programmes de maintenance		44
Nettoyage du mousseur de lait		44
Détartrage	45
Nettoyage	45
calc‘nClean	46
Conseils pour économiser l’énergie		47
Protection contre le gel		47
Rangement des accessoires		47
Accessoires		48
Mise au rebut		48
Garantie		48
Données techniques		48
Eliminer soi-même
les problèmes simples		49

+ 134 hidden pages