DIGITAL CAMCORDER
DSR-300 DSR-300P
INDEX PICTURE BOARD
DSBK-301
CAMERA ADAPTOR
CA-WR855
SERVICE MANUAL
Vol. 1 (1st Edition)
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
X-RAY RADIATION WARNING
Be sure that parts replacement in the high voltage block and adjustments made to the high voltage circuits are carried out precisely in accordance with the procedures given in this manual.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
Ersatz nur durch denselben oder einen vom Hersteller empfohlenen ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en likvärdig typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt gällande föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
Introducing this manual This manual is the Service Manual Vol. 1 of the digital camcorder DSR-300/300P, the index picture board DSBK-301 and the camera adaptor CA-WR855.
This manual contains the operation manual related to the operations of this equipment, the replacement of the parts and adjustments.
Related manuals |
In addition to this Service Manual Vol. 1, the following manuals are provided. |
|
. Service Manual Vol. 2 |
|
Part No. 9-977-332-21 |
|
Contains block diagrams, board layouts, schematic diagrams, semiconductor pin |
|
assingments and parts lists. |
|
. Service Manual DXF-701/701CE/701WS/701WSCE |
|
Part No. 9-977-265-02 |
|
See the DXF-701/701CE/701WS/701WSCE service manual available separately. |
|
. Service Manual VCT-U14 |
|
Part No. 9-977-221-01 |
|
See the VCT-U14 service manual available separately. |
DSR-300(E)/V1 |
1 |
|
1. |
OPERATING INSTRUCTIONS |
|
1-1. |
DSR-300/300P ................................................................................................ |
1-1 |
1-2. |
DSBK-301 (IPM-66 BOARD) ..................................................................... |
1-64 |
1-3. |
CA-WR855 ................................................................................................... |
1-66 |
2. |
SERVICE INFORMATION |
|
|
2-1. LOCATION OF MAJOR PARTS ................................................................. |
2-1 |
||
2-1-1. |
Location of Major Mechanical Parts ..................................................... |
2-1 |
|
2-1-2. |
Location of the Boards .......................................................................... |
2-3 |
|
2-1-3. |
Location of Sensors ............................................................................... |
2-5 |
|
2-2. REMOVING AND ATTACHING THE CABINET ..................................... |
2-6 |
||
2-2-1. |
Left Panel and Cassette Compartment Lid ............................................ |
2-6 |
|
2-2-2. |
Right Panel ............................................................................................ |
2-6 |
|
2-2-3. |
Lower Panel ........................................................................................... |
2-7 |
|
2-2-4. |
Rear Panel Assembly............................................................................. |
2-7 |
|
2-3. FUNCTIONS OF CASSETTE ....................................................................... |
2-8 |
||
2-4. |
CIRCUIT STRUCTURE ................................................................................ |
2-9 |
|
2-5. NOTES ON TIGHTENING SCREWS ........................................................ |
2-10 |
||
2-6. ATTACHING THE 4" OR 5" VIEWFINDER ............................................ |
2-11 |
||
2-7. EXTRACTING THE CASSETTE TAPE WHEN TAPE SLACKS ............ |
2-12 |
||
2-8. OPERATING THE UNIT WITHOUT LOADING A CASSETTE TAPE ... |
2-13 |
||
2-9. |
SHIFTING THE REEL ................................................................................ |
2-14 |
|
2-9-1. |
When the power can be turned ON ..................................................... |
2-14 |
|
2-9-2. |
When the power cannot be turned ON ................................................ |
2-14 |
|
2-10. REMOVAL OF MECHANICAL DECK ..................................................... |
2-15 |
||
2-11. REMOVAL AND ATTACHING THE BOARDS ...................................... |
2-16 |
||
2-11-1. |
FP-98 Board ........................................................................................ |
2-16 |
|
2-11-2. |
FP-99 Board ........................................................................................ |
2-17 |
|
2-11-3. |
GCN-15 and SW-929 Boards .............................................................. |
2-17 |
|
2-11-4. |
DPR-99/99P and ES-21/21P Boards ................................................... |
2-18 |
|
2-11-5. |
DU-27 Board ....................................................................................... |
2-18 |
|
2-11-6. |
AT-117 Board ...................................................................................... |
2-19 |
|
2-11-7. |
VA-178 Board ..................................................................................... |
2-19 |
|
2-11-8. |
SV-164 Board ...................................................................................... |
2-20 |
|
2-11-9. |
HN-227 Board ..................................................................................... |
2-21 |
|
2-11-10. |
AA-92 Board ....................................................................................... |
2-21 |
|
2-11-11. |
PS-495 Board ...................................................................................... |
2-22 |
|
2-11-12. |
CN-1519 Board ................................................................................... |
2-22 |
|
2-11-13. |
CP-315 Board ...................................................................................... |
2-23 |
|
2-11-14. |
MB-753 Board ..................................................................................... |
2-24 |
|
2-11-15. |
CN-1444 Board ................................................................................... |
2-25 |
|
2-11-16. |
SW-888 Board ..................................................................................... |
2-25 |
|
2-11-17. |
PSW-56 Board ..................................................................................... |
2-26 |
|
2-11-18. |
CC-68 Board ........................................................................................ |
2-26 |
|
2-11-19. |
RP-91 Board ........................................................................................ |
2-27 |
|
2-12. ATTACHING THE DSBK-301 (IPM-66 BOARD) .................................... |
2-28 |
DSR-300/P(E)/V1 |
3 |
|
2-13. CLEANING WHEN HEAD CLOGS .......................................................... |
2-28 |
|
2-13-1. Using a Cleaning Cassette ................................................................... |
2-28 |
|
2-13-2. Using the Cleaning Cloth .................................................................... |
2-28 |
|
2-14. RELEASING THE HUMID TIMER WHEN |
|
|
CONDENSATION OCCURS ...................................................................... |
2-29 |
|
2-15. DC-DC CONVERTER VOLTAGE CONFIRMATION ............................. |
2-30 |
|
2-16. CONNECTING CONNECTORS ................................................................ |
2-31 |
|
2-17. INPUT/OUTPUT SIGNALS OF CONNECTORS ...................................... |
2-31 |
|
2-18. BOARD SWITCH AND SLIT SETTINGS ................................................. |
2-37 |
|
2-18-1. |
SV-164 Board ...................................................................................... |
2-37 |
2-18-2. |
ES-21/21P Board ................................................................................. |
2-37 |
2-19. CHANGING THE BATTERY BEFORE END/BATTERY END AND |
|
|
BP BATTERY PRESET VOLTAGE .......................................................... |
2-38 |
|
2-19-1. Changing the Voltage (1) .................................................................... |
2-38 |
|
2-19-2. Changing the Voltage (2) .................................................................... |
2-41 |
|
2-20. REPLACING THE FILTER ........................................................................ |
2-45 |
|
2-21. CHANGING THE VIEWFINDER CORRESPOND TO LEFT EYE ......... |
2-46 |
|
2-22. REPLACING THE FLAT CABLES, |
|
|
FLEXIBLE CARD WIRES/BOARDS ........................................................ |
2-47 |
|
2-23. SERVICE TOOLS AND TEST FIXTURES ............................................... |
2-48 |
|
2-23-1. Attaching the Extension Board EX-622 .............................................. |
2-48 |
|
2-23-2. Service Tools and Test Fixtures .......................................................... |
2-49 |
|
2-24. ERROR CODES ........................................................................................... |
2-51 |
|
2-24-1. Servo System, Tape Path System, Reel Mechanism, |
|
|
|
and Sensor System Errors .................................................................... |
2-52 |
2-24-2. Communication Error of Microcomputer and Peripheral Devices ..... |
2-55 |
|
2-25. MENU (LCD) ............................................................................................... |
2-58 |
|
2-25-1. |
User Menu ........................................................................................... |
2-58 |
2-25-2. |
System Menu ....................................................................................... |
2-61 |
2-25-3. |
Maintenance Menu .............................................................................. |
2-64 |
2-26. MENU (VIEWFINDER) .............................................................................. |
2-68 |
|
2-26-1. Operation of Service Mode ................................................................. |
2-68 |
|
2-26-2. Reset Items and Standard Setting Value ............................................. |
2-69 |
|
2-26-3. |
Service Menu ....................................................................................... |
2-71 |
2-27. AUTO CHECK FUNCTION ....................................................................... |
2-83 |
|
2-28. NOTES ON REPAIR PARTS ...................................................................... |
2-88 |
|
2-28-1. Replacement Procedure of Chip Parts ................................................. |
2-88 |
|
2-28-2. Note on Replacing the ROM ............................................................... |
2-89 |
|
2-28-3. |
Initializing the EEPROM .................................................................... |
2-90 |
2-28-4. |
KY EEPROM Echo Back Data Preset Procedure ............................... |
2-91 |
3. PERIODIC MAINTENANCE AND INSPECTION
3-1. MAINTENANCE TIME TABLE .................................................................. |
3-1 |
|
3-2. |
HOURS METER ............................................................................................ |
3-2 |
3-3. |
MAINTENANCE AFTER REPAIRS ............................................................ |
3-3 |
3-4. |
CLEANING METHOD ................................................................................. |
3-3 |
3-5. |
AFTER USE IN COASTAL AREAS AND DUSTY AREAS ...................... |
3-5 |
4 |
DSR-300/P(E)/V1 |
|
4. REPLACEMENT/ALIGNMENT OF MAJOR PARTS
4-1. GENERAL INFORMATION ON REPLACEMENT/ALIGNMENT OF |
|
PARTS ............................................................................................................ |
4-1 |
4-2. REPLACEMENT OF CASSETTE COMPARTMENT ASSEMBLY .......... |
4-5 |
4-3. REPLACEMENT OF DRUM ASSEMBLY ................................................. |
4-6 |
4-4. REPLACEMENT OF S REEL TABLE ASSEMBLY .................................. |
4-7 |
4-5. REPLACEMENT OF T REEL TABLE ASSEMBLY .................................. |
4-8 |
4-6. REPLACEMENT OF SOFT BRAKE ARM (S) ........................................... |
4-9 |
4-7. REPLACEMENT OF HARD BRAKE ARM (S) ASSEMBLY .................. |
4-10 |
4-8. REPLACEMENT OF SOFT BRAKE (T) ASSEMBLY COMPONENTS ... |
4-11 |
4-8-1. Replacement of Soft Brake Arm (T) Assembly .................................. |
4-11 |
4-8-2. Replacement of TL Soft Brake Assembly ........................................... |
4-11 |
4-9. REPLACEMENT OF HARD BRAKE ARM (T) ASSEMBLY ................. |
4-12 |
4-10. REPLACEMENT OF SUB REEL GEAR (S) ASSEMBLY ....................... |
4-13 |
4-11. REPLACEMENT OF SUB REEL GEAR (T) ASSEMBLY ....................... |
4-14 |
4-12. REPLACEMENT OF TR BAND ASSEMBLY .......................................... |
4-15 |
4-13. REPLACEMENT OF SHIFT MOTOR ASSEMBLY ................................. |
4-16 |
4-14. REPLACEMENT OF LD ASSEMBLY ...................................................... |
4-17 |
4-15. REPLACEMENT OF SENSOR ATTACHMENT PLATE ASSEMBLY .. |
4-18 |
4-16. REPLACEMENT OF TR ARM ASSEMBLY ............................................ |
4-19 |
4-17. REPLACEMENT OF GL (S) ASSEMBLY ................................................ |
4-21 |
4-18. REPLACEMENT OF GL (T) ASSEMBLY ................................................ |
4-24 |
4-19. REPLACEMENT OF S REEL PLATE ASSEMBLY ................................. |
4-27 |
4-20. REPLACEMENT OF T REEL PLATE ASSEMBLY ................................. |
4-28 |
4-21. REPLACEMENT OF C ASSEMBLY ......................................................... |
4-29 |
4-22. REPLACEMENT OF PINCH ARM ASSEMBLY ..................................... |
4-30 |
4-23. REPLACEMENT OF TG-1/TG-8 GUIDE ASSEMBLY |
|
COMPONENT PARTS ................................................................................ |
4-31 |
4-24. REPLACEMENT OF TG-3 GUIDE ASSEMBLY |
|
COMPONENT PARTS ................................................................................ |
4-32 |
4-25. REPLACEMENT OF TG-7 GUIDE ASSEMBLY |
|
COMPONENT PARTS ................................................................................ |
4-33 |
4-26. REPLACEMENT OF IDLER GEAR ASSEMBLY .................................... |
4-34 |
4-27. REPLACEMENT OF MODE GEAR ASSEMBLY .................................... |
4-35 |
4-28. REPLACEMENT OF CAPSTAN MOTOR ................................................ |
4-37 |
4-29. REPLACEMENT OF MODE SLIDER ....................................................... |
4-38 |
4-30. REPLACEMENT OF REEL MOTOR ........................................................ |
4-41 |
4-31. REPLACEMENT OF REEL MOVING ARM ASSEMBLY ...................... |
4-42 |
4-32. REPLACEMENT OF REEL PLATE PRESSING LINK ASSEMBLY ...... |
4-43 |
4-33. REPLACEMENT OF MIC ASSEMBLY .................................................... |
4-45 |
4-34. REPLACEMENT OF CCD UNIT ............................................................... |
4-46 |
4-35. REPLACEMENT OF DC-DC CONVERTER ............................................ |
4-51 |
4-36. S REEL TABLE, T REEL TABLE HEIGHT CHECK/ADJUSTMENT .... |
4-52 |
4-37. GUIDE HEIGHT CHECK/ADJUSTMENT ................................................ |
4-53 |
4-38. REEL TABLE FWD/REV REWINDING TORQUE |
|
CHECK/ADJUSTMENT ............................................................................. |
4-56 |
4-39. FWD BACK TENSION CHECK/ADJUSTMENT ..................................... |
4-60 |
4-40. TR ARM ASSEMBLY POSITION CHECK/ADJUSTMENT ................... |
4-61 |
DSR-300/P(E)/V1 |
5 |
|
5. TAPE PATH ALIGNMENT
5-1. GENERAL INFORMATION FOR TAPE PATH ALIGNMENT |
................ 5-1 |
|
5-1-1. Equipment and Tools Used ................................................................... |
5-1 |
|
5-1-2. Tape Guide Adjustment Driver and Locking Screw ............................. |
5-1 |
|
5-1-3. Tape Path Adjustment Preparations ...................................................... |
5-2 |
|
5-1-4. Connection ............................................................................................. |
5-2 |
|
5-1-5. Drum and Tape Guide Positions ........................................................... |
5-3 |
|
5-1-6. |
Tape Path State ...................................................................................... |
5-3 |
5-2. SYSTEM SETTING MENU .......................................................................... |
5-4 |
|
5-3. TAPE PATH SYSTEM CHECK ................................................................... |
5-6 |
|
5-3-1. Check of Alignment Tape Playback ...................................................... |
5-6 |
|
5-3-2. Check of self-recording tape playback .................................................. |
5-7 |
|
5-4. TRACKING ADJUSTMENT ........................................................................ |
5-8 |
|
5-5. TG-1, TG-2 AND TG-3 GUIDES ADJUSTMENT ...................................... |
5-9 |
|
5-6. TG-7 AND TG-8 GUIDES ADJUSTMENT ............................................... |
5-11 |
|
5-7. CHECK AFTER ADJUSTMENT ................................................................ |
5-13 |
|
5-7-1. |
Tracking Check ................................................................................... |
5-13 |
5-7-2. FWD Search and REV Search Check ................................................. |
5-14 |
|
5-7-3. |
Rising Check ....................................................................................... |
5-14 |
5-7-4. |
Tape Path Check .................................................................................. |
5-15 |
5-8. SWITCHING POSITION ADJUSTMENTS ............................................... |
5-16 |
6. GENERAL INFORMATION FOR ELECTRICAL ALIGNMENT
6-1. |
ADJUSTING ITEMS ..................................................................................... |
6-1 |
6-2. |
EQUIPMENT AND TOOLS REQUIRED .................................................... |
6-2 |
6-3. |
MENU OPERATION ..................................................................................... |
6-5 |
7. CAMERA BLOCK ELECTRICAL ALIGNMENT
7-1. PREPARATION ............................................................................................ |
7-1 |
|
7-1-1. |
Equipment Required .............................................................................. |
7-1 |
7-1-2. Connection ............................................................................................. |
7-1 |
|
7-1-3. Switch Setting before Adjustment ......................................................... |
7-2 |
|
7-1-4. |
Notes on Adjustment ............................................................................. |
7-2 |
7-1-5. |
Adjustment Item .................................................................................... |
7-3 |
7-2. PREPARATION BEFORE ADJUSTMENT ................................................. |
7-4 |
|
7-2-1. Color Bar Signal Confirmation ............................................................. |
7-4 |
|
7-2-2. |
Sensitivity Confirmation ....................................................................... |
7-4 |
6 |
DSR-300/P(E)/V1 |
|
7-3. ADJUSTMENT .............................................................................................. |
7-5 |
|
7-3-1. |
Character Size Adjustment .................................................................... |
7-5 |
7-3-2. |
Subcarrier Frequency Adjustment ......................................................... |
7-5 |
7-3-3. |
INT SC-H Phase Adjustment ................................................................ |
7-5 |
7-3-4. |
Y/R-Y/B-Y CLP Level Adjustment ...................................................... |
7-6 |
7-3-5. |
Y/SYNC/R-Y/B-Y Level Adjustment................................................... |
7-6 |
7-3-6. |
Carrier Balance Adjustment .................................................................. |
7-7 |
7-3-7. |
Chroma (VBS) Level Adjustment ......................................................... |
7-7 |
7-3-8. |
Y (VBS) Level Adjustment ................................................................... |
7-8 |
7-3-9. |
Y (Y/C) Level Adjustment .................................................................... |
7-8 |
7-3-10. |
Chroma (Y/C) Level Adjustment .......................................................... |
7-9 |
7-3-11. |
VF SYNC/BLKG Level Adjustment .................................................... |
7-9 |
7-3-12. |
CCD Output Level Adjustment ........................................................... |
7-10 |
7-3-13. |
Shading Adjustment ............................................................................ |
7-10 |
7-3-14. |
Flare Adjustment ................................................................................. |
7-11 |
7-3-15. |
TONE Level Adjustment..................................................................... |
7-11 |
8. VTR BLOCK ELECTRICAL ALIGNMENT
8-1. SYSTEM CONTROL ADJUSTMEMT ........................................................ |
8-2 |
|
8-1-1. |
Clock Frequency Adjustment ................................................................ |
8-2 |
8-2. SERVO SYSTEM ADJUSTMENT ............................................................... |
8-3 |
|
8-2-1. |
Capstan FG Duty Adjustment ............................................................... |
8-3 |
8-2-2. |
Reel FG Duty Adjustment ..................................................................... |
8-4 |
8-3. RF SYSTEM ADJUSTMENT ....................................................................... |
8-5 |
|
8-3-1. |
REC Current Adjustment ...................................................................... |
8-5 |
8-3-2. |
PLL Adjustment .................................................................................... |
8-6 |
8-3-3. |
AGC and Delay Adjustment .................................................................. |
8-7 |
8-3-4. |
AUTO EQ Adjustment .......................................................................... |
8-8 |
8-4. AUDIO SYSTEM ADJUSTMENT ............................................................... |
8-9 |
|
8-4-1. |
Audio Level Volume Reference Position Adjustment ........................ |
8-12 |
8-4-2. |
Monitor Output (LINE OUT) Level Adjustment ................................ |
8-12 |
8-4-3. |
Limiter Level Adjustment ................................................................... |
8-12 |
8-5. VIDEO SYSTEM ADJUSTMENT .............................................................. |
8-13 |
|
8-5-1. |
PB Y SYNC Level Adjustment ........................................................... |
8-15 |
8-5-2. |
PB Y Level Adjustment ...................................................................... |
8-16 |
8-5-3. |
PB Y/B-Y Delay Adjustment .............................................................. |
8-17 |
8-5-4. |
PB Y/R-Y Delay Adjustment .............................................................. |
8-19 |
8-5-5. |
PB R-Y Level Adjustment .................................................................. |
8-21 |
8-5-6. |
PB B-Y Level Adjustment .................................................................. |
8-22 |
8-5-7. |
PB Burst Level Adjustment ................................................................. |
8-23 |
8-5-8. |
PB VBS Y Level Adjustment .............................................................. |
8-24 |
8-5-9. |
EE Y Level Adjustment ...................................................................... |
8-24 |
8-5-10. |
EE Chroma Level Adjustment ............................................................ |
8-25 |
DSR-300/P(E)/V1 |
7 |
|
300/P(E)/V1-DSR
1-1
3-861-961-11(1) |
.1-1 |
|
300/300P-DSR |
Digital Camcorder
Operating Instructions
Before operating the unit, please read this manual |
|
thoroughly and retain it for future reference. |
|
INSTRUCTIONSOPERATING |
1SECTION |
DSR-300F/300PF |
|
|
|
DSR-300K/300PK |
from |
This |
|
DSR-300L/300PL |
|||
operation |
is section |
||
|
|||
ã 1998 by Sony Corporation |
.manual |
extracted |
|
|
|||
|
|
|
2-1
300/P(E)/V1-DSR
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Owner’s Record
The model and serial numbers are located on the top. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. |
|
Serial No. |
|
|
|
|
|
2
LITHIUM BATTERY
Replace the battery with a Sony CR2032 lithium battery. Use of another battery may present a risk of fire or explosion.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in fire.
Note
Keep the lithium battery out of the reach of children. Should the battery be swallowed, consult a doctor immediately.
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til laverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten.
Brukt batteri returneres apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en likvärdig typ som
rekommenderas av apparattillverkaren. Kassera använt batteri enligt gällande föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
For customers in the USA
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
Table of Contents
Chapter 1
Overview
Chapter 2
Fitting and
Connections
Product Configurations .................................................... |
7 |
Features ............................................................................. |
8 |
Features on Camera Section ................................................ |
8 |
Features on VCR Section .................................................... |
9 |
Location and Function of Parts ..................................... |
11 |
Front View ......................................................................... |
11 |
Right Side View ................................................................. |
12 |
Left and Upper View ......................................................... |
22 |
Rear and Bottom ................................................................ |
24 |
VCL-714BXA Zoom Lens ................................................ |
26 |
DXF-701WS/701WSCE Viewfinder ................................. |
28 |
Inserting and Replacing the Lithium Battery ............... |
31 |
Fitting the Lens ............................................................... |
32 |
Using Accessories .......................................................... |
34 |
Using the Viewfinder ......................................................... |
34 |
Using an Optional Microphone ......................................... |
35 |
Using a Video Light ........................................................... |
36 |
Fitting the Shoulder Strap ................................................. |
38 |
Connecting to Audio System ............................................. |
39 |
Fitting to a Tripod .............................................................. |
41 |
Using the LC-421 Carrying Case ...................................... |
42 |
Connections .................................................................... |
43 |
Connecting a Number of Camcorders ............................... |
43 |
Connecting an External VCR ............................................ |
43 |
Power Supply ................................................................... |
44 |
Using a BP-L40/L60/L60A/L90/L90A Battery Pack ....... |
44 |
Using an AC Adaptor ........................................................ |
45 |
Using the Anton Bauer Intelligent Battery System ........... |
46 |
Table of Contents |
3 |
300/P(E)/V1-DSR
Table of Contents
Chapter 3
Shooting
Table of Contents
Chapter 4
Viewfinder Screen
Displays and
Menus
4 Table of Contents
Basic Procedure for Shooting........................................ |
47 |
Recording ........................................................................ |
49 |
Cassettes for the DSR-300/300P ....................................... |
49 |
Recording on the Internal VCR ......................................... |
50 |
Recording on an External VCR ......................................... |
54 |
Back Space Editing ......................................................... |
55 |
Starting Back Space Editing at Any Tape Position ........... |
55 |
Using the Edit Search Function |
|
While Back Space Editing ........................................... |
56 |
Using the Freeze Mix Function ......................................... |
57 |
Playback — Checking Recorded Contents ................... |
58 |
Checking the Recorded Contents Immediately After |
|
Shooting — Recording Review .................................... |
58 |
Viewing Monochrome Playback in the Viewfinder ........... |
58 |
Viewing Color Playback .................................................... |
58 |
Setting Time Values ......................................................... |
59 |
Setting the User Bit Value ................................................. |
60 |
Setting the Time Code Value ............................................. |
61 |
Synchronization With External Time Code Signals |
|
— Gen-Lock................................................................. |
63 |
ClipLink Shooting ........................................................... |
65 |
Setting Editing Points While Shooting .............................. |
67 |
Resuming Recording in ClipLink Mode ........................... |
69 |
Viewfinder Screen Indications ....................................... |
73 |
Changing the Viewfinder Display ..................................... |
73 |
Viewfinder Normal Indications ....................................... |
74 |
Status Indications .............................................................. |
77 |
Viewfinder Basic Menu ................................................... |
78 |
Basic Menu Operations ..................................................... |
78 |
Contents and Settings of Each Page .................................. |
78 |
Viewfinder Advanced Menu ............................................ |
83 |
Advanced Menu Operations .............................................. |
83 |
Contents and Settings of Each Page .................................. |
84 |
Using SetupLog ............................................................... |
90 |
Chapter 5 |
|
|
Adjustments and |
Setting on the VCR Section — VCR Menu ..................... |
91 |
Settings |
VCR Menu Operation ...................................................... |
92 |
|
Basic Operation ................................................................. |
92 |
|
Menu 101 Setting the Real Time Clock and Calendar ..... |
93 |
|
Menu 201 Checking the Total |
|
|
Operating (Power-On) Hours ....................................... |
93 |
|
Menu 204 Selecting Frame Mode (DF/NDF) |
|
|
for Time Code (for DSR-300 Only) ............................. |
93 |
|
Menu 206 Selecting Battery Capacity Indication ............ |
94 |
|
Menu 207 Setting Standby-On Period ............................. |
94 |
|
Menu 210 Using Auto-Check Function ............................ |
95 |
|
Menu 211 Selecting ClipLink Function ........................... |
97 |
|
Menu 212 Selecting Audio Recording Mode ................... |
97 |
|
Menu 213 Selecting Audio Reference Level .................... |
98 |
|
Menu 214 Setting Fade-In/Fade-Out for the Audio |
|
|
Recording Start and Stop Points. ................................. |
98 |
|
Menu 220 Using Setup Add (for DSR-300 Only) ............ |
99 |
|
White Balance Adjustment ........................................... |
100 |
|
Saving an Appropriate White Balance Value |
|
|
in Memory .................................................................. |
100 |
|
Using the Preset White Balance Settings ........................ |
101 |
|
Light Sources and Color Temperature ............................. |
102 |
|
Using the ATW (Auto Tracing White Balance) |
|
|
Function ...................................................................... |
102 |
|
Black Balance Adjustment ........................................... |
103 |
|
Shutter Settings ............................................................ |
104 |
|
Viewfinder Screen Adjustments .................................. |
106 |
|
Adjusting the Lens ........................................................ |
107 |
|
Flange Focal Length Adjustment .................................... |
107 |
|
Iris Adjustments ............................................................... |
108 |
|
Ajusting the Iris Sensitivity ............................................. |
109 |
|
Macrophotography .......................................................... |
109 |
|
Settings for Special Cases ........................................... |
110 |
|
Skin Detail Correction ..................................................... |
111 |
|
Adjusting Color in the Specified Area ............................ |
111 |
|
Table of Contents 5 |
3-1
4-1
300/P(E)/V1-DSR
Table of Contents
Appendixes
Important Notes on Operation ..................................... |
113 |
Characteristics of CCD Sensors ...................................... |
113 |
Cleaning the Video Heads ............................................ |
114 |
Warning System ............................................................ |
115 |
Condensation ................................................................... |
116 |
Troubleshooting ............................................................ |
117 |
Specifications ................................................................ |
119 |
Related Products .............................................................. |
121 |
Chart of Optional Components and Accessories ...... |
122 |
Glossary ......................................................................... |
123 |
6 Table of Contents
Product Configurations
The six models, DSR-300F, DSR-300K, DSR-300L, |
shown in the figure below. The operation of the basic |
|
DSR-300PF, DSR-300PK and DSR-300PL, comprise |
camcorder is the same in all cases. |
|
both NTSC and PAL versions and the components as |
|
|
DSR-300F/300PF |
|
|
DSR-300K/300PK |
|
|
DSR-300L/300PL |
|
|
|
Microphone |
VCT-U14 Tripod |
DXF-701WS/701WSCE |
Adaptor |
Viewfinder |
|
|
Switch guard |
|
|
|
RM-LG1 Remote |
DSR-300/300P Camcorder |
Test chart for flange |
Shoulder strap |
Control Unit |
|
|||
focal length |
|
||
|
|
|
|
|
adjustment |
|
|
VCL-714BXA
Zoom Lens
LC-300SFT Soft
Carrying Case
Chapter 1 Overview |
7 |
OverviewOverview1 Chapter 1 Chapter
300/P(E)/V1-DSR
Overview 1 Chapter
Features
Features on Camera Section
1/2-inch IT type Power HAD CCD
The DSR-300/300P Digital Camcorder uses 1/2-inch IT type Power HAD CCDs. It excels in reduction of smear, sensitivity and picture quality.
•Smear: –110 dB
•Sensitivity: F11.0 (at 3200 K, 2000 lux)
•S/N: 62 dB (DSR-300) or 60 dB (DSR-300P)
Sophisticated image processing
TruEye™ processing makes possible the following performance features. This digital signal processing has brought reproduction of natural colors to the level achieved by the human eye.
DynaLatitude™
Enables detailed adjustment of contrast control in each pixel in accordance with a histogram of luminance signal levels.
DCC+ (dynamic contrast control plus)
Prevents white breakup when shooting a high intensity subject, and also prevents color faults in high intensity subject.
Black stretch and compress
Enables control of luminance signal levels in black areas without changing the hue.
Variety of detail corrections
•Skin detail function: this function gives a slightly softer appearance to the subject’s face. The target skin color can be automatically set.
•Black halo correction
•Red/green vertical detail correction: this function performs vertical detail compensation for both red and green signals.
•Horizontal detail frequency control
New Functions boost operability
EZ (easy) mode function
When there isn’t time to check the camcorder settings, simply press the EZ mode button to start the auto adjustment function using standard settings. There is no need to lose a shot for lack of setup time.
EZ (easy) focus
Press the EZ focus button before shooting to ensure a quick and accurate focus.
Dual pixel readout (DPR1))
When the gain is set to either 18 dB or 24 dB, the gain setting can be doubled (6 dB up) without increasing the noise level.
Programmable gain
The amount of gain relative to the GAIN switch setting (H, M, or L) can be programmed as –3 dB, 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 18 dB, 18 dB+DPR, 24 dB,
24 dB+DPR and hyper gain.
Hyper gain
Hyper gain (36 dB (=30 dB+DPR), or about 60 times greater than 0 dB) can be easily set via one switch setting. This can also be done from remote equipment.
Auto tracing white balance (ATW)
This function automatically traces the white balance, which constantly changes as lighting conditions change. Auto tracing white balance is especially useful when there is no time to manually adjust the white balance or when shooting moves between indoor and outdoor locations.
Total level control system (TLCS)
Even if the incoming light exceeds the range in which the standard auto iris can control exposure, the auto gain control (AGC) or auto exposure (AE) backs up to ensure proper exposure.
Recording time (REC TIME) display
Recording time can be displayed in either of the following modes.
•Total recording time for all cuts (TTL2))
•Total recording time for current cut (DUR3))
..........................................................................................................................................................................................................
1) |
DPR = Dual Pixel Readout |
3) DUR = Duration |
2) |
TTL = Total |
|
8 |
Chapter 1 Overview |
|
Viewfinder super detail
Video signals for the viewfinder are mixed with DTL signals to make focusing easier.
Dual zebra pattern display
Two types of zebra patterns, zebra 1 and zebra 2 can be displayed simultaneously or independently. The zebra 1 can be set to the levels ranging from 70 to 90 IRE on the DSR-300 (or from 70 to 90% on the DSR300P) and the zebra 2 indicates the levels of 100 IRE or more for the DSR-300 (or the levels of 100% or more for the DSR-300P).
Color temperature display
When reading the white balance, the color temperature is displayed on the viewfinder screen.
Switching the color temperatures for the preset white balance
You can select the preset white balance at 3200 K or 5600 K by setting the FILTER control. The 3200 K preset can be switched to the 3000 K preset when the menu setting is changed.
Video monitor output with text
The video signal with text superimposed that is shown in the viewfinder can also be output to an external video monitor.
1-kHz reference signal output
Along with a color bar, a 1-kHz reference signal can also be output.
Freeze mix function
The freeze mix function superimposes any previously recorded still picture on the viewfinder screen to facilitate framing the subject when reshooting the scene.
Edit Search Function
Pressing the EDIT SEARCH buttons allows the tape to play back in search mode. Set either of two playback speeds.
SetupLogTM function
Settings at shooting are recorded onto the tape in real time. This recorded data can then be used to reproduce the same shooting conditions in subsequent shots. It also makes it easier to identify the cause of problems in previous shots.
Video light control
A video light connector and control switch are equipped. You can turn the light on and off automatically as you start and stop VCR operation.
High-performance viewfinder (DXF701WS/701WSCE)
•High resolution (600 TV lines of horizontal resolution)
•Large-diameter eye cup for easier viewing and focusing
•PEAKING potentiometer for vertical and horizontal detail control
•Two indicators can be used as TALLY indicators
•Tough die-cast aluminum body
Features on VCR Section
The DSR-300/300P uses the DVCAM recording format. The internal signal processing is digitalized to provide more stable output signals and higher reliability.
Compatible with consumer DV
A DV cassette recorded on a DV-format VCR can be played back on the DSR-300/300P. (Cassettes recorded in LP mode cannot be played back.)
DVCAM cassettes
•The DSR-300/300P can use both standard-size and mini-size DVCAM cassettes. According to cassette size, the DSR-300/300P automatically corrects reel position.
•The maximum recording/playback times are 184 minutes for standard size cassettes and 40 minutes for mini cassettes.
•DVCAM cassettes include a cassette memory. Information about the editing points (ClipLink™ log data) that is specified while shooting is recorded into this cassette memory.
Chapter 1 Overview |
9 |
Overview 1 Chapter
5-1
6-1
Features
Overview 1 Chapter
ClipLink™ function
The ClipLink function links all stages from shooting to editing. Once editing points have been set with this function during shooting, they can be used to boost the efficiency of editing work.
Creation of clips
Using the ClipLink function, the camcorder operator can create clips to be used during editing.
The images captured at the Mark IN points are recorded in a compressed format onto the tape as “Index Pictures” 1). In addition, editing point-related data (scene number, time code for Mark IN/OUT points, etc.) is recorded in the cassette memory.
ClipLink mode
To use the ClipLink function, select the menu setting to set the DSR-300/300P into ClipLink mode. There is also a ClipLink continue function that enables clips to be continued even after a break in recording.
PCM digital audio
Recording/playback can be set to audio lock mode. Selectable between two-channel recording (with a sampling frequency of 48 kHz) mode or four-channel recording (with a sampling frequency of 32 kHz) mode (CH-1 and CH-2 only).
VCR data display
The DSR-300/300P is able to display the following data on the viewfinder screen.
•Time values (counter, time code, or user bit values)
•Audio recording levels
•Remaining tape time
•Operation mode of the VCR section
•Remaining battery capacity
•ClipLink information
Recording on external VCRs
Betacam or S-VHS VCRs can be connected to the VTR connector (26-pin) on the rear panel.
Equipped with audio output connectors
During recording or playback, audio output can be monitored via a built-in speaker, a connected earphone or via (two-channel) audio output connectors.
Color playback
Connect an external video monitor for color playback (playback adaptor not required). The DSR-300/300P is equipped with two video monitor connectors: one for composite video output and the other for S-video output.
..........................................................................................................................................................................................................
1)It is necessary to fit the optional DSBK-301 Index Picture Board.
-DSR |
10 |
Chapter 1 Overview |
|
300/P(E)/V1 |
|||
|
|
Location and Function of Parts
Front View
0 Switch guard fitting screws |
|
How to fit the switch guard |
|
1. Detach the two screws (M3). |
1 MIC IN +48 V connector |
2. Place the supplied switch guard so that the |
|
EZ MODE button, A.IRIS MODE switch and |
|
ATW button are covered, and retain it using |
2 VF connector |
the two screws detached in step 1. |
|
|
3 FILTER control |
|
4 Lens mount |
|
5 SHUTTER switch |
|
6 TAKE button |
|
7 AUDIO LEVEL knob |
Switch guard |
8 WHT/BLK switch |
(supplied) |
|
|
9 VTR button |
1 MIC (microphone) IN +48 V connector (XLR 3- pin, female)
Connect the supplied microphone or an optional microphone (operable with a 48 V supply).
2 VF (viewfinder) connector (20-pin)
This is the connector for the DXF-701WS/701WSCE viewfinder.
3 FILTER control
Select the color temperature conversion filter appropriate to the lighting conditions. (See page 47.)
4 Lens mount
Attach the zoom lens here.
5 SHUTTER switch
Use this switch to set the shutter speed, CLS (clear scan), or EVS setting (see page 104). Usually, set this switch to OFF.
6 TAKE button
Press this button to specify an editing point (Mark IN/ OUT or Cue point) at the current tape position during shooting. (See page 67.)
7 AUDIO LEVEL knob
You can use this knob to manually adjust the channel 1 audio recording level.
8 WHT/BLK (white/black) switch
This switch is used for automatic adjustment of the white balance and black balance. (See pages 100 to 103.)
9 VTR button
Pressing this button starts and stops recording on the VCR.
0 Switch guard fitting screws
If you will not use the EZ MODE button (4 on page 13), A.IRIS MODE switch (6 on page 13) and ATW button (!¢ on page 13), fit the supplied switch guard to avoid miss-operation of them.
Chapter 1 Overview 11
Overview 1 Chapter
300/P(E)/V1-DSR
Location and Function of Parts
Right Side View
Front section
Overview 1 Chapter
1 EZ FOCUS button
2 EDIT SEARCH buttons
3 LIGHT switch
4 EZ MODE button and indicator
5 ZEBRA button and indicator
6 A.IRIS MODE switch and indicator
7 MENU switch
8 W.BAL switch |
9 MENU dial |
0 POWER switch
!¡ OUTPUT/DL/DCC+ switch
!™ NG button
!£ GAIN switch
!¢ ATW button and indicator
1 EZ FOCUS button
Press this button to turn the “easy focus” function on. This opens the iris, to make it easier to focus before beginning shooting. The indication “EZ FOCUS” appears in the viewfinder while the function is on; to turn it off, press the EZ FOCUS button again. If left on, the function automatically turns off after about ten seconds.
Note
If the “easy focus” function is still on when you press the VTR button, it turns off automatically and recording starts about one second later.
2 EDIT SEARCH buttons
You can see the search playback while pressing either of these buttons at recording pause mode to quickly find the next recording start point. Two playback speeds are available, and press either of the buttons to the inner position to increase the speed.
3 LIGHT (video light) switch
Controls the video light connected as follows. AUTO: turns on the video light at recording if the
power switch on the light is set on.
MAN (manual): allows the power switch on the video light to turn the light on and off.
12 Chapter 1 Overview
4 EZ (“easy”) MODE button and indicator
Press this button (EZ mode on) when you want to be able to shoot immediately, with automatic adjustment of the camcorder settings to standard values. (See page 88 for EZ mode setting.) When this function is used, the iris and the white balance are adjusted automatically. (The total level control system functions.) Press this button again to return the camcorder to the previous settings (EZ mode off).
Note
When the RM-M7G Remote Control Unit is connected, the “easy mode” function is disabled.
5 ZEBRA button and indicator
Depress this button to display a zebra pattern (diagonal stripes) in the viewfinder.
Depending on the zebra setting in advanced menu page 4 (see page 86), the zebra 1 for video levels between 70 to 90 IRE (or 70 to 90%) and the zebra 2 for video levels 100 IRE or more (or 100% or more) can be displayed independently or simultaneously.
6 A.IRIS (auto iris) MODE switch and indicator
When you use the auto iris function (by setting the iris selector on the lens to A), set this switch to suit the shooting conditions. Selecting BACK L gives more light to back-lit subjects, and selecting SPOT L adjusts for high contrast in spot-lit subjects. For normal shooting, set this switch to STD.
7 MENU switch
When you press this switch to the ON position, the basic menu is displayed. Keep pressing it to the ON position to cycle through the various menu displays. When you press the switch to the STATUS position, the camcorder’s status (of current settings) is displayed.
8 W. BAL (white balance) switch
This selects the white balance setting from the preset value, the value in memory A or the value in memory B. (See page 100.) You can select the preset white balance at 3200 K or 5600 K using the FILTER control (3 on page 11). If you select the 3200 K preset, it can be switched to the 3000 K preset in advanced menu page 3 (see page 85).
9 MENU dial
Use this dial to change menu pages or settings.
0 POWER switch
Powers the camcorder on or off.
!¡ OUTPUT/DL/DCC+ (DynaLatitude/dynamic contrast control plus) switch
Use this switch to select the DCC+ function, the DynaLatitude function, or color bar output. Select the CAM/DCC+ position in most cases.
CAM/DCC+: This activates the DCC+ function. This prevents color faults when shooting highintensity subjects.
CAM/DL: This setting uses the DynaLatitude function, which finely adjusts the contrast of each pixel according to a histogram of luminance signal levels. Access advanced menu page 2 to set the DynaLatitude function ON or OFF. The DynaLatitude effect can be set to any of three levels, Low, STD (standard), and High with basic menu page 2.
BARS: This setting displays color bars.
For details of menu operation, see Chapter 4 “Viewfinder Screen Displays and Menus”.
!™ NG button
When using the ClipLink function during shooting, you can designate a particular scene as “NG” (No Good) by pressing this button before shooting the next scene. Press the button again to cancel the NG setting.
!£ GAIN switch
This selects one of the three gain settings, high, medium or low. You can choose the gain values assigned to the H, M and L settings from values from –3 dB to 24 dB + DPR and hyper gain.(See page 85.) The factory default selections are 18 dB (H), 9 dB (M) and 0 dB (L).
Note
When the HYPER GAIN switch (7 on page 21) is in the ON position, the GAIN switch has no effect.
!¢ ATW (auto tracing white balance) button and indicator
Press this button, turning the indicator on, when you want the white balance to be adjusted automatically to follow changes in lighting conditions. (See page 102.)
Chapter 1 Overview 13
Overview 1 Chapter
7-1
8-1
Location and Function of Parts
Rear section
1Chapter |
|
|
|
|
|
1 EJECT button |
EJECT |
STOP |
REW |
PLAY |
F FWD |
2 Tape transport buttons and indicators |
|
|
|
|
|
|
|
|
Overview |
|
|
|
|
|
|
3 EARPHONE connector
4 WARNING indicator
5 LIGHT switch
6 DISPLAY switch
7 AUDIO LEVEL (CH-1/CH-2) knobs
8 Display window
9 RESET/(MENU SET) button
0 Speaker
!¡ ALARM knob
!™ MONITOR knob
300/P(E)/V1-DSR
1 EJECT 6button
Press to open the cassette holder (1 on page 23) when the camcorder is powered.
2 Tape transport buttons and indicators
These buttons transport the tape as shown below.
Note
During recording, none of these buttons operates.
Buttons Operation
REW 0 Rewinds the tape. The indicator lights while the tape is being rewound.
Press while the tape is being rewound or during playback to view reverse search playback.
F FWD ) Fast forwards the tape. The indicator lights while the tape is being fast forwarded. Press while the tape is being fast forwarded or during playback to view forward search playback.
PLAY ( Plays back the recorded video. The indicator lights during playback.
STOP p Stops the tape.
14 Chapter 1 Overview
3 EARPHONE connector (mini-jack)
Connect an earphone or headphones. This outputs the sound which was output to the speaker (0 on page 17), but mutes the speaker.
4 WARNING indicator
This lights or blinks when an abnormality occurs.
For details, see “Warning System” on page 115.
5 LIGHT switch
This switches the display window (8 on page 15) light on or off.
6 DISPLAY switch
Switches time value indication shown in the display window (8 on page 15).
COUNTER: Shows the tape transport time in HH:MM:SS (hours, minutes and seconds).
TC: Shows the time code value.
U-BIT: Shows the user bit data in the time code.
7 AUDIO LEVEL (CH-1/CH-2) (audio recording |
The audio levels are indicated in the display window 8. |
level adjustments for channels 1 and 2) knobs |
For details, see “ 8 Display window”. |
When the AUDIO SELECT (CH-1/CH-2) switches |
8 Display window |
(4 on page 19) are set to MANUAL, these knobs |
|
adjust the audio levels being recorded on channels 1 |
Shows the following items. Use the LIGHT switch (5 |
and 2. |
on page 14) to light up the display window. |
s Time value indication
rClip remaining indication
qTape remaining indication
pBattery capacity indication
oService indication
1)When the optional DSBK-301 is fitted
aPlayback indication b DATE indication
c Non-drop frame indication (DSR-300 only)
d External synchronization lock indication
e Hold indication
f Audio level indicators
PB DATE NDF EXT-LK |
|
HOLD |
OVER |
dB |
OVER |
|
|
|
0 |
|
|||
H |
MIN SEC |
FRM |
|
-12 |
|
|
|
-20 |
|
||||
CLIP |
|
CL CONT IP |
|
|
||
|
|
|
|
|||
TAPE |
|
|
DVCAM |
|
-30 |
|
BATT E |
|
|
|
|
-40 |
|
|
F |
Li |
|
-∞ |
|
|
DIAG RF SERVO HUMID SLACK 1 |
F 8 32k |
2 |
||||
F 8 48k |
m Audio mode indications
n Warning indications
g ClipLink log data indication
hClipLink continue indication
CL CONT IP i IP indication 1)
DVCAM
Li j Lithium backup battery warning
k DVCAM indication
l Cassette memory indication
Indications in the display window
Indication |
Description |
a Playback indication |
Appears during playback, fast forward or rewind with the time data display showing a |
|
time code or user bit value. |
b DATE indication |
Appears when the date or time is displayed in the time value indication s area. |
c Non drop-frame indication (DSRAppears when non-drop frame mode is selected. |
|
300 only) |
|
d External synchronization |
Appears when the internal time code generator is locked to an external signal input to |
indication |
the TC IN connector (3 on page 23). |
e Hold indication |
Appears when the internal time code generator is stopped. |
f Audio level indicators |
These show the audio recording or playback levels of channel 1 and channel 2. |
g ClipLink log data indication |
Appears when using a cassette with cassette memory containing ClipLink log data. |
h ClipLink continue indication |
Appears when back space editing using ClipLink function is possible. |
i IP(Index Picture) indication |
Appears when the ClipLink function is set to on in the VCR menu and Index Picture |
|
recording is allowed. (The optional DSBK-301 is required.) |
|
(Continued) |
|
Chapter 1 Overview 15 |
Overview 1 Chapter
300/P(E)/V1-DSR
Overview 1 Chapter
Location and Function of Parts
j Lithium backup battery warning |
Appears when the voltage of the internal lithium backup battery (CR2032) is low. If this |
|
indication appears, replace the lithium backup battery immediately. |
|
For further information about replacing lithium battery, see “Inserting and Replacing |
|
the Lithium Battery” (page 31). |
k DVCAM indication |
Disappears when the cassette being played back is not for DVCAM format. |
l Cassette memory indication |
Appears when using a cassette with cassette memory. |
m Audio mode indications |
These show audio recording/playback mode. |
|
Fs32k: 4-channel mode (32kHz sampling frequency) |
|
Fs48k: 2-channel mode (48kHz sampling frequency) |
|
For further information about selecting audio recording mode, see “Selecting Audio |
|
Recording Mode ¾Menu 212” (page 97). |
n Warning indications |
Include the following. |
|
RF: Appears when the video heads are clogged, or when there is a fault in the |
|
recording system. |
|
SERVO: Appears when the servo lock is not functioning. |
|
HUMID: Appears when there is condensation on the drum. |
|
SLACK: Appears when there is a tape winding fault. |
|
For measures against warning indications, see “Warning System” (page 115). |
o Service indication |
Appears during maintenance on VCR menu operations (page 92). It does not appear |
|
during normal operation. |
p Battery capacity indication |
This indicates the battery capacity and voltage as shown below. |
|
Change menu setting for the battery you are using. |
For menu settings, see “Selecting Battery Capacity Indication ¾Menu 206” (page 94).
|
Battery voltage |
|
Indication |
BP-L40/L60/L60A/ NP-1B/BP-90A |
|
|
L90/L90A |
|
BATT E[pppppp]F |
15.0 V or more |
12.5 V or more |
BATT E[pppppp]F |
14.0 to 15.0 V |
12.0 to 12.5 V |
BATT E[pppppp]F |
13.0 to 14.0 V |
11.75 to 12.0 V |
BATT E[pppppp]F |
12.0 to 13.0 V |
11.5 to 11.75 V |
BATT E[pppppp]F |
11.3 to 12.0 V |
11.3 to 11.5 V |
BATT E[pppppp]F (blinking)1) |
11.25 to 11.3 V |
11.25 to 11.3 V |
BATT E[pppppp]F (blinking) |
11.0 to 11.25 V |
11.0 to 11.25 V |
BATT E[pppppp]F (blinking) |
11.0 V or less |
11.0 V or less |
1)Replace the battery pack when this indication appears.
(Continued)
16 Chapter 1 Overview
q Tape remaining indication |
During recording or pause mode, this indication shows the remaining tape time as |
|||
|
shown below. It is not displayed when no cassette is loaded. |
|
||
|
Indication |
Tape time remaining |
|
|
|
TAPEppppppp |
30 minutes or more |
|
|
|
TAPEpppppp |
25 to 30 minutes |
|
|
|
TAPEppppp |
20 to 25 minutes |
|
|
|
TAPEpppp |
15 to 20 minutes |
|
|
|
TAPEppp |
10 to 15 minutes |
|
|
|
TAPEpp |
5 to 10 minutes |
|
|
|
TAPEp |
2 to 5 minutes |
|
|
|
TAPEp(blinking) |
0 to 2 minutes |
|
|
|
TAPE (blinking) |
End of tape |
|
|
r Clip remaining indication |
This shows how many clip shots or Cue points can be recorded1). |
|||
|
Indication |
Clip shots |
|
Cue point |
|
CLIPpppppp |
51 or more |
101 points or more |
|
|
CLIPppppp |
41 to 50 |
81 to 100 points |
|
|
CLIPpppp |
31 to 40 |
61 to 80 points |
|
|
CLIPppp |
21 to 30 |
41 to 60 points |
|
|
CLIPpp |
11 to 20 |
21 to 40 points |
|
|
CLIPp |
1 to 10 |
1 to 20 points |
|
|
CLIPp(blinking) 2) |
1 to 3 |
1 to 6 points |
|
|
CLIP |
Cannot record |
|
|
|
CLIP (blinking) 2) |
Cannot record |
|
|
|
1) The optional DSBK-301 is required for Index Picture recording. |
|||
|
2) When back space editing using ClipLink function is possible (when CONT is |
|||
|
displayed) |
|
|
|
s Time value indication |
Depending on the DISPLAY switch (6 on page 14) setting, this shows a counter |
|||
|
value, time code value or user bit value. Press the MENU button (1 on page 18) to |
|||
|
display the VCR menu. |
|
|
|
9 RESET/(MENU SET) (counter reset/VCR menu) button
Resets the time value shown in the display window. This button operates differently depending on settings of the DISPLAY switch (6 on page 14) and the TC mode switch 1 (9 on page 19) and 2 (8 on page 19).
Switch setting |
RESET button operation |
DISPLAY: COUNTER |
Resets counter value to |
|
0:00:00. |
DISPLAY: TC |
Resets time code to |
TC mode switch 1: PRESET |
00:00:00:00. |
TC mode switch 2: SET |
|
DISPLAY: U-BIT |
Resets user bit a) to |
TC mode switch 1: PRESET |
00 00 00 00. |
TC mode switch 2: SET |
|
a)Bits of time code recorded on tape, in which users can record necessary information.
Also, this button is used to change menu settings.
For details on the VCR menu, see “Setting on the VCR Section ¾VCR Menu” (page 91).
0 Speaker
Outputs the recorded or playback audio. When a warning indicator appears in the viewfinder or display window, the speaker sounds a warning tone.
The speaker is muted (does not output a warning tone) when an earphone is connected to the EARPHONE connector (3 on page 14).
For details on the warning tone, see “Warning System” (page 115).
Chapter 1 Overview 17
Overview 1 Chapter
9-1
10-1
Location and Function of Parts
|
!¡ ALARM (alarm tone volume adjustment) knob |
!™ MONITOR (monitor volume adjustment) knob |
|
|
|||
|
|||
|
Controls the volume of the warning tone that is output |
Controls the volume of the sound other than the |
|
|
|||
|
via the speaker (0 on page 17) or earphone (3 on |
warning tone that is output via the speaker (0 on page |
|
|
|||
|
|||
|
page 14). Turning this knob to the minimum setting |
17) or earphone (3 on page 14). Turning this knob to |
|
|
|||
|
|||
|
mutes the alarm tone. |
the minimum setting mutes the audio output. |
|
|
|||
1 Chapter |
|||
Operation panel under the cover |
|
||
Overview |
Right side |
|
|
|
|
|
|
|
|
|
|
|
|
|
1 MENU button |
|
||
|
|
|
|
|
|
|
|
|
2 ADVANCE button |
|
||
|
|
|
|
|
|
|
|
|
3 SHIFT button |
|
||
REC TIME SKIN DTL |
EXT VTR |
MENU ADVANCE |
|
SHIFT |
|
|
|
|
||||
TTL |
|
|
|
OUTPUT |
|
|
|
|
|
|
|
|
|
|
ON COMPONENT. |
|
|
|
|
|
|
|
|
||
DUR |
|
|
OFF |
VBS |
|
|
|
|
|
|
|
|
OFF |
|
|
|
Y/C |
|
|
|
|
|
AUDIO LEVEL |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
TTL RESET |
SET |
|
VTR |
MONITOR SELECT PRESET |
|
F-RUN |
|
|
AUTO |
4 AUDIO SELECT |
||
|
|
|
|
|
|
|
|
|
|
MAN |
||
|
|
|
|
TRIGGER |
CH-1 |
REGAIN |
SET |
|
AUDIO SELECT |
(CH-1/CH-2) |
||
|
|
|
|
|
MIX |
|
||||||
|
|
|
|
PARALLEL |
CH-2 |
|
|
|
|
CH-1 |
CH-2 |
switches |
|
|
|
|
EXT |
|
|
|
|
||||
|
|
|
|
INT ONLY |
|
|
|
LITHIUM BATT |
||||
|
HYPER |
MATRIX |
EXT ONLY |
|
DATE/TIME |
|
R-RUN |
AUDIO IN |
|
|||
|
ClipLink |
|
|
|
|
|
||||||
|
GAIN |
|
FRONT MIC |
|
MONITOR OUT |
|
|
|
|
|||
|
|
CONTINUE |
|
|
|
FRONT |
|
|||||
ON |
H.SAT |
LOW CUT |
|
CHARACTER |
|
|
|
|||||
|
|
|
|
|
|
VJ MIC |
5 AUDIO IN (CH-1/ |
|||||
OFF |
FL |
ON |
|
|
|
ON |
|
|
|
WRR |
||
|
STD |
|
OFF |
|
|
|
|
|
|
REAR |
CH-2) switches |
|
|
|
|
|
|
|
|
OFF |
|
|
|
|
6 Lithium battery compartment
7 MONITOR OUT CHARACTER switch
8 TC mode switch 2
9 TC mode switch 1
0 ClipLink CONTINUE button
!¡ MONITOR SELECT switch
300/P(E)/V1-DSR
1 MENU button
Press this button to display the VCR menu in the display window.
For details about the VCR menu, see “Setting on the VCR Section —VCR Menu” (page 91).
2 ADVANCE button
When setting time code and user bit values, or at menu
18 Chapter 1 Overview
setting, press this button to increment the digit that has been selected with the SHIFT button (3 on page 19). In other case, keep pressing this button to show the clip remaining indication instead of time value. (Example: CLIP 045)
For time code and user bit settings, see page 59.
On how to use the ADVANCE button for menu settings, see “Setting on the VCR Section —VCR Menu” (page 91).
3 SHIFT button
When setting time code and user bit values, or at menu setting, keep pressing this button to select a digit. The selected digit will start blinking.
In other case, keep pressing this button to show the date (when the DISPLAY switch (6 on page 14) is set to U-BIT) and time (when the DISPLAY switch is set to TC) instead of time value.
For time code and user bit settings, see page 59.
On how to use the SHIFT button for menu settings, see “Setting on the VCR Section —VCR Menu” (page 91).
4 AUDIO SELECT (CH-1/CH-2) (audio recording level adjustments manual/auto selection for channels 1 and 2) switches
These select the audio recording level adjustment method.
AUTO: Use the AGC (automatic gain control) circuit to automatically adjust the audio level.
MANUAL: Enables users to manually adjust the AUDIO LEVEL (CH-1/CH-2) knobs (7 on page 15) for each channel. Select AUTO if excess input levels are likely to occur.
5 AUDIO IN (CH-1/CH-2) (audio input selection for channels 1 and 2) switches
These select the input signals to channels 1 and 2. FRONT: Signals from the microphone connected to
the MIC IN +48 V connector.
VJ MIC: Signals from the remote control unit with microphone connected to the REMOTE connector 2
WRR: Signals from the WRR-855A synthesized tuner connected to the WRR connector via the CA-WR855 Camera Adaptor.
MANUAL: Signals from a microphone or external equipment connected to the AUDIO IN (CH-1/ CH-2) connectors.
6 Lithium battery compartment
Insert the supplied CR2032 Lithium Battery.
On how to fit the lithium battery, see page 31.
7 MONITOR OUT (monitor output)
CHARACTER switch
Set ON to superimpose text information on the monitor output.
Note
Set this switch ON when using the freeze mix function.
8 TC (time code) mode switch 2
Sets the mode for advancing time code values when the TC mode switch 1 9 has been set to PRESET.
F-RUN: The time code advances continuously whether or not the camcorder is recording. Use this setting to align the time code value with real time.
SET: Use this setting to set the time code or user bit value.
R-RUN: The time code value advances only during recording. Use this setting to have consecutive recordings on the tape.
Note for the DSR-300
There are two time code frame modes: drop-frame (DF) mode and non drop-frame (NDF) mode. This product is shipped with drop-frame mode selected.
For details on switching between drop-frame mode and non drop-frame mode, see “Selecting Drop-frame (DF)/Nondrop frame (NDF) mode (for DSR-300) —Menu 204” (page 93).
For details on drop-frame mode and non drop-frame mode, see “Drop-frame mode (for DSR-300 Only)” on page 62.
9 TC (time code) mode switch 1
Selects between resetting the time code value or continuing from the time code value at the end of the previous recording.
PRESET: This starts recording time code values on the tape from the currently set value.
REGEN: During back space editing, this reads the tape’s current time code value and sets the time code to record starting from that value. The time code value is advanced in R-RUN mode regardless of the setting on TC mode switch 2 8.
DATE/TIME: This synchronizes the time code to the real time clock set in the VCR menu (see page 93). In this case the time code of the DSR-300 is recorded in DF (drop-frame mode).
Note
If the ClipLink function is set to on (meaning ClipLink shooting is allowed) in menu 211 and CONT is displayed in the display window, regardless of the setting of this switch, the time code generator automatically enters the REGEN mode at recording. (When you will not perform ClipLink shooting, set the ClipLink function to oFF (see page 65).
Chapter 1 Overview 19
Overview 1 Chapter
300/P(E)/V1-DSR
Overview 1 Chapter
Location and Function of Parts
0 ClipLink CONTINUE button
When restart ClipLink shooting, press this button to add the new clip at the end of the recorded clips.
Note
When restart recording without pressing this button, the pre-recorded ClipLink log data and Index Pictures are deleted.
For details , see “ClipLink Shooting” (page 65).
Left side
!¡ MONITOR SELECT (audio monitor selection) switch
Selects audio output via the speaker (0 on page 17) or earphone.
CH-1: Channel 1 audio
MIX: Mixed audio (channels 1 and 2) CH-2: Channel 2 audio
EXT: The sound selected by an external VCR connected to the VTR connector (8 on page 25)
1 REC TIME switch
2 SKIN DTL switch
3 EXT VTR OUTPUT switch
REC TIME SKIN DTL |
EXT VTR |
MENU ADVANCE |
|
SHIFT |
|
|
|
|||
TTL |
|
|
OUTPUT |
|
|
|
|
|
|
|
|
ON COMPONENT. |
|
|
|
|
|
|
|
||
DUR |
|
OFF |
VBS |
|
|
|
|
|
|
|
OFF |
|
|
Y/C |
|
|
|
|
|
AUDIO LEVEL |
|
TTL RESET |
SET |
VTR |
MONITOR SELECT PRESET |
|
F-RUN |
|
|
AUTO |
||
|
|
|
|
|
|
|
|
|
MAN |
|
|
|
|
TRIGGER |
CH-1 |
|
|
|
|
|
|
|
|
|
|
MIX |
REGAIN |
SET |
|
AUDIO SELECT |
||
|
|
|
PARALLEL |
CH-2 |
|
|||||
|
|
|
EXT |
|
|
|
|
CH-1 |
CH-2 |
|
|
|
|
INT ONLY |
|
|
|
LITHIUM BATT |
|||
|
|
|
|
DATE/TIME |
|
R-RUN |
||||
|
HYPER MATRIX |
EXT ONLY |
|
|
AUDIO IN |
|||||
|
ClipLink |
|
|
|
|
|||||
|
GAIN |
FRONT MIC |
|
MONITOR OUT |
|
|
|
|||
|
CONTINUE |
|
|
|
FRONT |
|||||
ON |
H.SAT |
LOW CUT |
|
CHARACTER |
|
|
||||
|
|
|
|
|
|
VJ MIC |
||||
OFF |
FL |
ON |
|
|
|
|
|
|
|
WRR |
|
STD |
OFF |
|
|
|
ON |
|
|
|
REAR |
OFF
4 VTR TRIGGER switch
5 FRONT MIC LOW CUT switch
6 MATRIX switch
7 HYPER GAIN switch
8 SKIN DTL SET button
9 TTL RESET button
1 REC (recording) TIME switch
Selects the recording time indication in the viewfinder. TTL (TOTAL): Displays the total recording time.
The total recording time is not reset even when you stop the VCR and power off the camcorder, for example, to replace the battery pack.
DUR (DURATION): Displays the recording time of the current cut.
OFF/TC: Switches off the recording time display. If, however, in advanced menu 6 you set the time code display item (TC IND) to ON (see page 87), then the VCR time data (time code, counter, or user bit value) is displayed.
Note
The recording time displayed when this switch is set to TTL or DUR is obtained by counting the duration of the internal reference signal input to the camcorder. The value may not agree exactly with the value derived from the time code values. Furthermore, the value displayed may not be correct when another manufacture’s VCR is connected to the camcorder.
2 SKIN DTL (skin detail) switch
Set this switch ON to use the skin detail correction function.
For details, see “Skin Detail Correction” (page 111).
3 EXT VTR OUTPUT switch
Depending on the external VCR connected to the VTR connector (8 on page 25), this switches the video signal output to the VCR.
COMPONENT/VBS: Component/composite video signal
Y/C: S-video signal
4 VTR TRIGGER switch
Sets the function of the VTR button on the camcorder or lens when a VCR is connected to the VTR connector (8 on page 25).
PARALLEL: Operates both internal and external VCRs.
INT ONLY: Operates the internal VCR only. External VCR operation is performed locally.
EXT ONLY: Operates the external VCR only.
5 FRONT MIC LOW CUT switch
Set this switch to ON to insert a high-pass filter in the microphone circuit, reducing wind noise.
Normally leave the switch in the OFF position.
6 MATRIX switch
Selects the color matrix setting to change the picture color adjustment.
H.SAT: Colors are emphasized.
FL: Colors appear normal even when shooting under fluorescent lighting.
STD: The color matrix in standard setting is used. Normally leave the switch in this position.
7 HYPER GAIN switch
Setting this switch to ON increases the gain by a factor of about 60 with respect to 0 dB (a 30 dB increase by electronic amplification and a 6 dB increase for DPR, bringing about a total gain increase of 36 dB).
When this switch is in ON position, the indication “HYPER” appears in the viewfinder, and the GAIN UP indicator in the viewfinder also lights.
When finished shooting, return this switch to OFF position. The “HYPER” indication disappears and the GAIN UP indicator goes out.
Note
Increasing the gain with this switch reduces the horizontal resolution by approx. 50%.
8 SKIN DTL (skin detail ) SET button
Press this button with the SKIN DTL switch 2 to display the area detect cursor on viewfinder screen. Place the cursor on the target and press this button to perform skin detail correction.
For details, see “Skin Detail Correction” (page 111).
9 TTL (total) RESET button
Pressing this button resets the total recording time (TTL selection) to 0.
Overview 1 Chapter
20 Chapter 1 Overview |
Chapter 1 Overview 21 |
11-1
12-1
Location and Function of Parts
Left and Upper View
Front section
1 Chapter |
1 Shoulder strap fitting |
|
Overview |
||
2 Accessory fitting shoe and screw hole |
||
|
3 Viewfinder left-to-right positioning ring |
4 Viewfinder fitting shoe
5 REMOTE connector 1 |
6 Viewfinder front-to-back position locking knob |
7 Fitting for optional microphone holder
8 Video light connector
1 Shoulder strap fitting
To use the supplied shoulder strap, fix one end here and the other end to the right side. (See page 38.)
9 LENS connector
0 VIDEO OUT connector
!¡ REMOTE connector 2
Note
The RM-81 cannot be connected.
6 Viewfinder front-to-back position locking knob
2 Accessory fitting shoe and screw hole
Attach optional video lights or other accessories here.
3 Viewfinder left-to-right position fixing ring
Loosen this ring to adjust the left-to-right position of the viewfinder. (See page 34.)
4 Viewfinder fitting shoe
Fix the DXF-701WS/701WSCE Viewfinder here.
5 REMOTE connector 1 (mini-jack)
Connect the RM-LG1 Remote Control Unit to enable remote operation of the ClipLink function.
Loosen this knob to adjust the front-to-back position of the viewfinder. (See page 34.)
7 Fitting for optional microphone holder
You can fit an optional CAC-12 Microphone Holder here. (See page 35.)
8 Video light connector
A video light with a maximum power consumption of 30 W such as the Anton Bauer Ultralight 2 or equivalent can be connected.
-DSR |
22 |
Chapter 1 Overview |
|
300/P(E)/V1 |
|||
|
|
9 LENS connector (12-pin)
If you use a lens with cable, connect the lens cable.
0 VIDEO OUT connector (BNC)
This outputs the video signal captured by the camcorder.
!¡ REMOTE connector 2 (10-pin)
Connect the optional RM-M7G Remote Control Unit to this connector. Set the CAMERA HEAD SELECT switch on the bottom of RM-M7G to 1.
Rear section
You can also connect a remote control unit with microphone.
Note
EZ mode cannot be used if the RM-M7G is connected to the camcorder.
For more information about a remote control unit with microphone, contact your Sony dealer.
1 Cassette holder
2 GEN LOCK IN connector
3 TC IN connector
4 TC OUT connector
5 S VIDEO OUT connector
6 MONITOR OUT connector
7 AUDIO OUT CH-1/CH-2 connectors
1 Cassette holder
Power the camcorder and press the EJECT button to open the lid. Insert the cassette and close the lid by pressing the indication “PUSH” .
2 GEN LOCK IN (gen lock video input) connector
(BNC)
When synchronizing the camcorder to an external signal, input a reference video signal (VBS or BS).
3 TC IN (time code input) connector (BNC)
Input an external signal for synchronizing the built-in time code generator. Use an SMPTE (DSR-300) or EBU (DSR-300P) time code signal.
Note
Use a jitterless LTC signal. Using an LTC signal reproduced by other equipment may cause the camcorder to malfunction.
Chapter 1 Overview 23
Overview 1 Chapter
300/P(E)/V1-DSR
Overview 1 Chapter
Location and Function of Parts
4 TC OUT (time code output) connector (BNC)
This outputs time code signals from the built-in time code generator. When a time code signal is input to the TC IN connector (3 on page 23), this output signal is synchronized to it.
For details about time code, see “Setting Time Values” on page 59.
5 S VIDEO OUT (S-video output) connector (DIN
4-pin)
This outputs the image being shot or played back as S- video signals. Connect to the S-video input connector on an external VCR or video monitor.
6 MONITOR OUT (output) connector
Outputs the image being shot or played back as composite video signals. Connect to the video input connector on an external VCR or video monitor.
Note
The output signal from this connector may discontinue when switching the operation between recording and playback. Do not use as a reference signal for external equipment.
7 AUDIO OUT CH-1/CH-2 (audio output channel
1 and 2) connectors (phono jacks)
These output the sound being recorded or played back. Connect to a stereo amplifier or video monitor’s audio input connectors.
Rear and Bottom
1 TALLY indicator
2 TALLY switch
3 Battery attachment interface
6 WRR connector
4 DC IN connector
5 AUDIO IN CH-1/CH-2 connectors and input selection switches
7 DC OUT connector
8 VTR connector
9 BREAKER button
3 Battery attachment interface
Attach a battery pack or an AC-DN1 AC Adaptor. When using the WRR-855A synthesized tuner (for wireless microphones), attach the CA-WR855 Camera Adaptor here.
For information about fitting a battery pack or an AC adaptor, see “Power Supply” (page 44). For information about attaching a synthesized tuner, see “Connecting to Audio System” (page 39).
4 DC IN (DC power input) connector (XLR 4-pin, male)
To use the camcorder with an AC power supply connect an optional AC-550/550CE or CMA-8A/ 8ACE AC Adaptor.
5 AUDIO IN CH-1/CH-2 (audio input channel 1 and 2) connectors (XLR 3-pin, female) and input selection switches
Connect a microphone or other external audio equipment. Set the input selection switches as shown below according to the microphone or equipment.
MIC+48V ON (right position): For connecting to a 48-V microphone
Note
If this position is selected for a microphone other than 48-V microphone, the microphone may be damaged.
MIC (center position): For connecting any microphone other than 48-V microphone
LINE (left position): For connecting an external audio signal source such as a stereo amplifier.
6 WRR (synthesized tuner) connector (7-pin)
Insert the WRR-855A synthesized tuner into the CAWR855 Camera Adaptor and connect the CA-WR855 here.
For information about attaching a synthesized tuner, see “Connecting to Audio System” (page 39)
7 DC OUT (DC power output) connector (4-pin, female)
This connector supplies power for a WRR-810A/860A UHF Portable Tuner.
8 VTR connector (26-pin, male)
Connect an external VCR.
9 BREAKER (breaker reset) button
If an excessive current flows in the internal circuits, the internal circuit breaker shuts off the power supply. Push this button after eliminating the cause of the excessive current.
Overview 1 Chapter
1 TALLY (back tally) indicator (red) |
2 TALLY switch |
This indicator lights during recording. It will not light |
Set this switch to ON to activate the TALLY indicator |
if the TALLY switch 2 is set to OFF. This indicator |
1 function. |
also blinks to indicate warnings in the same manner as |
|
the REC/TALLY indicator in the viewfinder. |
For details, see “Warning System” on page 115. |
24 Chapter 1 Overview |
Chapter 1 Overview 25 |
13-1
14-1
Location and Function of Parts
VCL-714BXA Zoom Lens
1 Chapter |
1 Focusing ring |
Overview |
2 Manual zoom control |
|
3 Iris ring |
|
4 F.f. fixing knob |
|
5 F.f. adjustment ring |
|
!£ Filter attaching |
|
thread |
|
6 Zoom remote control |
|
connector |
|
7 Focus remote control |
|
connector |
|
8 ZOOM selector |
|
9 Iris selector |
|
0 Instant automatic iris |
|
button |
!¢ MACRO button |
!¡ Power zoom switch |
|
|
and ring |
!™ RET button |
|
|
! VTR button |
|
-DSR |
26 |
Chapter 1 Overview |
|
300/P(E)/V1 |
|||
|
|
1 Focusing ring
Turn this ring to focus the lens on the subject.
2 Manual zoom control
For direct manual zoom control, set the ZOOM selector to the “M” position, and turn this control.
3 Iris ring
For manual iris control, set the iris selector to the “M” position, and turn this ring.
4 F.f. (flange focal length) fixing knob
Fixes the F.f. adjustment ring 5.
5 F.f. (flange focal length) adjustment ring
To adjust the flange focal length, loosen the F.f. fixing knob 4 on this ring, then turn the ring. (See page 107.)
6 Zoom remote control connector (8-pin)
For remote control of zoom operations, connect an optional LO-23 Lens Remote Control Unit.
7 Focus remote control connector (3-pin)
This is not used.
8 ZOOM selector
This selects the mode of zoom operation.
S (servo): power zoom
M (manual): manual zoom
9 Iris selector
This selects the mode of iris operation. (See page 108.)
A (automatic): automatic iris M (manual): manual iris
0 Instant automatic iris button
While using manual iris control, press this button to switch temporarily to the automatic iris control setting. The automatic setting is maintained as long as you hold the button down.
!¡ Power zoom switch
Use this to carry out a power zoom. W end: zoom toward wide angle T end: zoom toward telephoto
Pressing the switch harder increases the zoom speed.
!™ RET (return) button
This allows you to check the video signal as follows. When the internal VCR is in recording pause mode, press this button to review the last few seconds of the recording in the viewfinder (recording review). When an external VCR is connected, pressing this button connects the E-E1) video signal from the external VCR to the viewfinder while the internal VCR is recording or no tape is inserted in the internal VCR.
For details, see “Playback — Checking Recorded Contents” (page 58).
!£ Filter attachment thread (72 mm dia., 0.75 mm pitch)
Use to attach a commercially available threaded filter.
!¢ MACRO button and ring
For close-up work, hold this button down while turning the ring. (See page 109.)
! VTR button
This button starts and stops recording on the VCR. Press it once to start recording, and once more to stop.
..........................................................................................................................................................................................................
1)E-E video signal: “electric-to-electric” video signal. This is the input video signal which has passed through internal electrical circuits, but has not been converted to a magnetic signal.
Chapter 1 Overview 27
Overview 1 Chapter
300/P(E)/V1-DSR
Location and Function of Parts
DXF-701WS/701WSCE Viewfinder
Overview 1 Chapter
Note
You can switch the scan size of the DXF-701WS/ 701WSCE in accordance with the aspect ratio
1 BATT indicator
2 TAKE/TALLY indicator
3 REC/TALLY indicators
4 SHUTTER indicator
5 GAIN UP indicator
6 Eyepiece focusing knob
7 Accessory fixing screw hole
8 Tally lamp
Microphone holding screw
Microphone holder
Microphonea)
a) Not supplied with the optional DXF-701WS/701WSCE
selected on the camera or camcorder. However, it operates in 4:3 mode when used on the DSR-300/ 300P.
TALLY
TAKE REC BATT
SHUTTER |
GAIN UP |
Eye cup
9 Eyepiece release catch
0 BRIGHT control
!¡ CONTRAST control
!™ PEAKING control
!£ TALLY switch
!¢ Viewfinder connector
1 BATT (battery) indicator (red)
This indicates when the battery capacity is low.
2 TAKE/TALLY indicator (orange)
When using the ClipLink function while shooting, this indicator lights when the TAKE button (6 on page 11) has been pressed to set a Mark IN point and goes out when a Mark OUT point is set.
3 REC/TALLY (recording/tally) indicators (red)
•From the time when you press the VTR button (9 on page 11 and ! on page 27) on the lens or camcorder, this flashes until recording starts, then stays on continuously during recording.
•This is also used to indicate a fault. (See page 115.)
•The lower indicator can be disabled by menu setting.
(See page 86.)
28 Chapter 1 Overview
4 SHUTTER indicator (red)
This lights when the SHUTTER switch (5 on page 11) is in the ON position. (If the EVS is selected, the indicator will not light.)
5 GAIN UP indicator (orange)
This lights when the gain is 3 dB or more.
6 Eyepiece focusing knob
Turn this to adjust the viewfinder focus to match your eyesight. (See page 106.)
7 Accessory fixing screw hole
Attach optional video lights or other accessories here.
8 Tally lamp
When the TALLY switch !£ is in the ON position, this operates in the same way as the REC/TALLY indicators 3.
9 Eyepiece release catch
To view the viewfinder screen directly, press this catch, and hinge up the eyepiece.
0 BRIGHT (brightness) control
This adjusts the brightness of the viewfinder image.
(See page 106.)
!¡ CONTRAST control
This adjusts the contrast of the viewfinder image. (See page 106.)
!™ PEAKING control
This adjusts the outline intensity of the viewfinder image. (See page 106.)
!£ TALLY switch
Set this switch to the ON position to use the tally lamp
8.
!¢ Viewfinder connector (20-pin)
Connect this to the VF connector.
Overview 1 Chapter
Chapter 1 Overview 29
15-1
16-1
Inserting and Replacing the Lithium Battery
The camcorder uses a lithium battery to retain stored data. When using the camcorder for the first time, be sure to insert the supplied lithium battery (CR2032).
The camcorder will not operate correctly without this lithium battery.
Lifetime of the lithium battery
When the lithium battery’s voltage falls, the lithium backup battery warning Li appears in the display window. If this warning appears, replace the lithium battery (CR2032) within three or four days.
The lithium battery has an average service life of about two years, however operation in ClipLink mode will shorten the lifetime until about one year (when the DSBK-301 is fitted).
1 Turn the POWER switch on.
2 Press down the catch at the top of the battery cover and open the cover.
1 POWER switch
3 Take out the lithium battery.
4 Reverse step 3 to insert a replacement lithium battery. Make sure that the + symbol on the battery is facing you.
5 Close the battery cover.
Inserting or replacing the lithium battery
Notes
•Carefully read the instructions for inserting and replacing the lithium battery. Lithium batteries may explode if misused.
•Use only CR2032 Lithium Batteries. Other types of lithium batteries may come loose when the camcorder is moved. If you have difficulty finding CR2032 Lithium Batteries, contact your Sony dealer.
2
Catch
Press and pull forward.
LI
LITHIUM BATT
Battery cover
Press down and pull out toward you.
ConnectionsConnectionsand Fitting 2 Chapter and Fitting 2 Chapter
300/P(E)/V1-DSR
Chapter 2 Fitting and Connections |
31 |
300/P(E)/V1-DSR
Connections and Fitting 2 Chapter
Fitting the Lens
In the case of the DSR-300K/300PK/300F/300PF model, the lens is already fitted. In other cases, use the following procedure to fit the lens.
1 Remove the retaining rubber which prevents the lens mount from coming loose, then raise the lens fixing lever, and remove the lens mount cap.
2 With the lens fixing lever turned fully counterclockwise, push in the lens, aligning the projection on the lens with the cutout on the camcorder.
3 Supporting the lens, turn the lens fixing lever fully clockwise. Replace the retaining rubber on the lens mount.
Note
Be sure to turn off the power before fitting the lens.
Retaining rubber
Lens mount cap |
Lens fixing lever |
|
Align and push in.
32 |
Chapter 2 Fitting and Connections |
If using a lens with a 6-pin connector
This camcorder head has a 12-pin LENS connector. If the lens cable has a 6-pin connector, fit an adaptor cable: LO-612 (manufactured by Canon) or ECF-124 (manufactured by Fujinon) or equivalent.
If using a 2/3” lens
Fit the lens using the optional LO-32BMT 2/3” lens adapter.
Fitting optional filters
Loosen the lens hood fixing screw to remove the lens hood, then attach the filter.
Remove lens hood
|
|
2 Chapter |
|
|
and Fitting |
Filter (optional) |
Lens hood fixing screw |
Connections |
|
||
|
|
Chapter 2 Fitting and Connections |
33 |
17-1
18-1
Connections and Fitting 2 Chapter
Using Accessories
Using the Viewfinder
Removing the Viewfinder
Remove any microphone from the viewfinder before beginning.
1 Pull the viewfinder connector out of the VF connector on the front.
2 Loosen the viewfinder left-to- right position fixing ring, then pulling up the retaining catch, slide the viewfinder out.
Using an Optional Microphone
To use a long microphone such as the optional ECM670/672, remove the supplied microphone holder, and fit an optional CAC-12 Microphone Holder to the camcorder, then mount the microphone in this holder.
Removing the supplied microphone
VF connector
holder
Remove the two microphone holder retaining screws (M4 × 6) from the viewfinder, remove the microphone holder, then replace the screws in their original positions.
Microphone |
M4 × 6 screws |
holder |
|
Retaining catch
Viewfinder left-to-right position fixing ring
Fitting the optional CAC-12 Microphone Holder
Remove the two retaining screws (M3 × 8) for the optional microphone holder, then use these screws to attach the CAC-12 Microphone Holder.
Screws removed from the camcorder
CAC-12
Connections and Fitting 2 Chapter
300/P(E)/V1-DSR
To fit the viewfinder
Reverse the removal procedure. (You need not hold the viewfinder stopper up.)
Left eye adaptor
By fitting a left eye adaptor, you can use the camcorder with your left eye to the viewfinder.
Note
You cannot stow the camcorder attached with a left eye adaptor in the LC-421 Carrying Case.
For details, consult your Sony dealer.
Adjusting the viewfinder position
To adjust the viewfinder left-to-right position, loosen the left-to-right fixing ring, and to adjust the front-to- back position loosen the front-to-back position locking knob.
Viewfinder left-to-right Viewfinger front-to-back position fixing ring position locking knob
Fitting an optional microphone
Use the following procedure to attach an optional ECM-670 Microphone.
1 Loosen the screw of the CAC-
12 Microphone Holder, then open the holder and replace the microphone adaptor with the one supplied with the ECM670 Microphone.
34 |
Chapter 2 Fitting and Connections |
Microphone adaptor
(Continued)
Chapter 2 Fitting and Connections |
35 |
300/P(E)/V1-DSR
Using Accessories
2 Insert the microphone in the microphone holder, close the holder, and tighten the screw. Connect the microphone cable to the MIC IN +48 V connector.
2 Chapter |
Fitting optional microphones (operable with a |
Fitting |
48 V supply) other than the ECM-670 |
|
|
and |
Use the same fitting procedure as for the ECM-670, |
but note the following differences with respect to the |
|
Connections |
microphone adaptor. |
|
|
|
ECM-672: no microphone adaptor required. |
|
Slender microphones (19 mm (3/4 inch) diameter): |
|
use the microphone adaptor supplied with the |
|
CAC-12. |
36 |
Chapter 2 Fitting and Connections |
MIC IN +48 V connector
Mark
Using a Video Light
For the DSR-300/300P, you can use the Anton Bauer Ultralight 2 or equivalent. Use a video light powered by 12 V with maximum power consumption of 30 W.
•If you connect the video light to the video light connector on the DSR-300/300P (page 22) and set the LIGHT switch to AUTO (page 12), you can turn the light on and off automatically as you start and stop VCR operation.
•The output of the video light connector on the DSR300/300P is controlled to 12 V even when the camcorder is supplied with 12 V or more power (through the DC IN connector or battery pack). The brightness or color temperature of the light will not change according to voltage increase.
Notes
•Do not use the video light with power consumption of over 30 W.
•The brightness or color temperature of the light will change when the supplied voltage is under 12 V.
To fit the video light
Fit the video light to the camcorder grip or the accessory shoe on the viewfinder and connect the video light cable to the video light connector.
When using a video light with a long cable
You can pass a part of the cable through the camcorder grip.
1 Remove the cover of the camcorder grip and break off projection A (see the figure).
2 Pass the cable through the grip as shown in the figure and replace the cover.
When using equipment other than the camcorder for power supply
Break off projections A and B on the camcorder. (See step 1 of the previous section “When using a video light with a long cable”.) Insert the cable into the grip from the front hole and take out from the rear hole as shown in the figure.
Projection B |
Projection A |
Connections and Fitting 2 Chapter
Chapter 2 Fitting and Connections |
37 |
19-1
20-1
Using Accessories
Fitting the Shoulder Strap
This section describes the procedure for fitting the supplied shoulder strap to the camcorder.
1 Fit one of the clips to a shoulder strap fitting.
2 Chapter |
|
and Fitting |
|
Connections |
2 Fit the other clip to the |
|
|
|
shoulder strap fitting on the |
|
other side of the grip in the |
|
same way. |
Removing the shoulder strap
1Open the cover of the clip.
Open the cover of the clip and move the clip downwards to release it from the fitting.
2 Hook the clip over a shoulder strap fitting.
-DSR |
38 |
Chapter 2 Fitting and Connections |
|
300/P(E)/V1 |
|||
|
|
Connecting to Audio System
The DSR-300/300P is able to record sound not only from the microphone attached but also from a wireless microphone or an external audio system.
Using a wireless microphone system
You can use the wireless microphone system including a WRT-810A/830A UHF Wireless Microphone and a WRR-810A/855A/860A UHF Portable Tuner to record sound.
To connect a WRR-855A
1 Open the cover of the WRR connector.
For details on using the wireless microphone system, see the operating instructions for the microphone and tuner.
WRR connector
WRR
Connections and Fitting 2 Chapter
2 Insert the WRR-855A into the CA-WR855.
Fasten the screws (supplied with the WRR-855A).
3 Fit the attachment plate on the rear side of the CA-WR855 to the V-groove on the battery attachment interface, and then slide the CA-WR855 down until it connects to the WRR connector.
CA-WR855
4 Set one of the AUDIO IN (CH- 1/CH-2) switches to WRR.
Chapter 2 Fitting and Connections |
39 |