GS110TP_IG_8Feb10.fm Page 1 Tuesday, February 9, 2010 7:15 PM
)NSTALLATION 'UIDE
ProSafe® 8 Port Gigabit PoE Smart Switch™ with 2 fiber SFP GS110TP
Start Here
Follow these instructions to set up your smart switch. Before proceeding with the smart switch installation, familiarize yourself with the contents of the Resource CD, especially the reference manuals on your Resource CD.
First, Verify Package Contents
•ProSafe® GS110TP Smart Switch
•Rubber footpads for tabletop installation
•Power cord
•48V/1.25A power adapter
•Wall-mount kit
•Installation Guide
•Smart Switch Resource CD that includes the NETGEAR Device Manager Utility (Smart Control Center) and GS110TP Hardware Installation Guide. (A link to the online GS110TP Software Administration User's Manual is on the Resource CD.)
•Warranty/Support Information Card.
Then, Prepare to Install Your Smart Switch
Prepare a PC with an Ethernet adapter and a CD ROM drive.
Next, Install the NETGEAR Device Manager Utility (Smart Control Center) on a PC
1.Insert the Resource CD into your CD drive.
2.Run the Setup program to install the Smart Control Center utility. The Installation Wizard will guide you through the installation.
Next, Connect Your Smart Switch in the Correct
Order
These instructions assume you are using DHCP in your network. If you are using static IP addressing in your network, configure the switch IP address before connecting it to your network. In the absence of a DHCP server, the switch will default to 192.168.0.239 for its IP address.
To configure the switch before connecting it to your network:
1.Set up the PC with a Static IP address in the 192.168.0.x subnet, and connect the PC to the switch. Then, use the Smart Control Center utility to configure the switch.
2.Connect each PC to an RJ-45 network port on the switch front panel.
Use category 5 (Cat5) unshielded twisted-pair (UTP) cable terminated with an RJ-45 connector to make these connections.
Smart Switch
GS110TP
|
|
|
Link/Act |
PoE |
|
|
GS110TP |
||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
Power |
Link/Act Mode |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green = Link at 1000M |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PoE Max |
Yellow = Link at 100M/10M |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Blink = ACT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
PoE Mode |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green = PoE Powered |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link/Act |
9F |
Link/Act 10F |
||
|
|
Yellow = PoE Fault |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Servers |
Computers |
Printers |
3.Connect the switch to your network.
4.Power on the switch.
5.Verify that the PC with the Smart Control Center utility is on the same subnet as the switch.
Now, Configure the Switch with the NETGEAR Device Manager Utility (Smart Control Center)
1. Double-click the Smart Control Center icon on your desktop or in Windows Start menu Programs to run the utility and view this screen.
2. Click Discover to find your switch in the network.
Loading...