TE 76/TE 76P/TE 76-ATC/TE 76P-ATC combihammer
It is essential that the operating instructions are read before the tool is operated for the first time.
Always keep these operating instructions together with the tool.
Ensure that the operating instructions are with the tool when it is given to other persons.
Operating controls
Chuck locking sleeveFunction selector switchPower selector switchControl switch
Switch lock for chiselling
Tool components
Dust shieldChuck
Side handle Service indicator
Grip
Hammering mechanism / gearingMotor
Type plate
Theft protection indicator (option TE 76P / TE 76P-ATC)
Lock symbol
Contents |
Page |
|
1. |
General information |
11 |
2. |
Description |
11 |
3. |
Technical data |
13 |
4. |
Safety precautions |
14 |
5. |
Preparation for use |
15 |
6. |
Operation |
15 |
7. |
Insert tools and accessories |
17 |
8. |
Care and maintenance |
17 |
9. |
Manufacturer's warranty – tools |
18 |
10. |
Disposal |
18 |
11. |
Trouble shooting |
19 |
12. |
EC-Declaration of conformity |
19 |
1. General information
In these operating instructions, this symbol indi- cates points of particular importance to safety. The instructions at these points must always be observed in order to avoid the risk of serious injury.
Caution: high voltage
The numbers refer to the illustrations. The illustrations can be found on the fold-out cover pages. Keep these pages open while you read the operating instructions.
In these operating instructions, the power tool to which these operating instructions apply is referred to as “the tool”.
2.Description
The TE 76 / TE 76P / TE 76-ATC / TE 76P-ATC is an electrically powered rotary hammer and breaker with pneumatic hammering mechanism designed for professional use.
The following items are supplied: power tool, operating instructions, grease (50 ml), cleaning cloth, toolbox.
The following conditions must always be observed when the tool is in use:
–The tool must be connected to an alternating current electric supply in compliance with the information given on the type plate.
–The tool is for hand-held use only.
–The tool must not be used in places where the surrounding conditions may present a risk of explosion.
11
Main features of the tool
Electrical protection class II (double insulated) Z Active Torque Control TE76-ATC / TE76P-ATC (additional operator protection in drilling mode) Mechanical torque-limiting clutch
No-load hammering absorption
Grip and side handle with vibration absorption Quick-change chuck
TE-Y insert tool system
Infinitely variable speed, with electronic regulation independent of load
Selector switch for full power (II) and half power (I) Drilling and chiselling modes
Control switch lockable in chiselling mode 24-way chisel position adjustment
Gearing and hammering mechanism with oil lubrication
Automatic cut-out carbon brushes Service indicator with light signal Pivotable side handle
Depth gauge attachment (optional)
Right of technical changes reserved
Theft protection system (option TE 76P / TE 76P-ATC)
The tool may be equipped with the optional theft protection system. If the tool is equipped with this feature, it can be activated and made ready for operation only by way of the corresponding activation key.
The tool is designed for the following uses:
Use |
Required insert tools |
Working range |
Drilling in concrete, masonry |
Drill bit with TE-Y connection end |
Drilling range in concrete |
and natural stones |
– Hammer drill bits |
12– 40 mm dia. |
|
– Breach bits |
40– 80 mm dia. |
|
– Percussion core bits |
45–150 mm dia. |
Chiselling in concrete, masonry |
Pointed, flat and shaped chisels |
Surface finishing and breaches |
and natural stone |
with TE-Y connection ends |
|
Setting anchor |
Setting tools with TE-Y |
All Hilti anchors with TE-Y setting tools |
|
connection ends |
|
Drilling in wood and metal |
Chuck holder, item 263359 |
|
|
Keyless chuck, item 60208 |
|
|
Wood drill bits and metal drill bits |
Wood drill bits, 10–32 mm dia. |
|
with smooth or hex. shank |
Metal drill bits, 10–20 mm dia. |
Mixing non-flammable |
Chuck holder, item 263359 |
|
materials, e.g. grout |
Keyless chuck, item 60208 |
|
|
Mixing tools with smooth or |
Mixing tools, 80–150 mm dia. |
|
hex. shank |
|
12
3. Technical data
|
TE 76 / TE 76-ATC |
|
|
|
|
TE 76P / TE 76P-ATC |
|
|
|||||
Rated power |
1300 W |
1300 W |
1300 W |
1300 W |
1300 W |
1300 W |
1400 W |
1400 W |
1400 W |
1400 W |
1400 W |
||
Nominal |
|
|
|
|
|
|
|
|
|
|
|
|
|
voltage |
100 V |
110 V |
120 V |
220 V |
230 V |
|
240 V |
110 V |
120 V |
|
220 V |
230 V |
240 V |
Nominal |
|
|
|
|
|
|
|
|
|
|
|
|
|
current input 16 A |
13 A |
13 A |
6.4 A |
6.4 A |
|
6.5 A |
14.1 A |
13.7 A |
|
7.0 A |
6.8 A |
6.9 A |
|
Frequency |
|
|
|
|
|
50–60 Hz |
|
|
|
|
|
|
|
Weight as per |
|
|
|
|
|
TE 76 / TE 76P |
|
7.4 kg |
|
|
|||
EPTA-Procedure 01/2003 |
|
|
|
TE 76-ATC / TE 76P-ATC |
8.3 kg |
|
|
||||||
Dimensions (l×h×w) |
|
|
|
|
TE 76 / TE 76P |
|
497 x 261 x 115 mm |
||||||
|
|
|
|
|
|
TE 76-ATC / TE 76P-ATC |
510 x 288 x 115 mm |
||||||
Minimum distance between wall and hole drilled |
|
38 mm |
|
|
|
|
|
|
|||||
Speed |
|
|
|
|
|
II = 0–282 I = 0–200 r.p.m. |
|
|
|||||
Typical drilling performance in |
|
|
|
20 mm dia.: 360 mm/min |
|
|
|
|
|||||
medium-hard B35 concrete |
|
|
|
25 mm dia.: 290 mm/min |
|
|
|
|
|||||
|
|
|
|
|
|
32 mm dia.: 180 mm/min |
|
|
|
|
|||
Typical chiselling performance in medium-hard |
|
|
|
|
|
|
|
|
|
||||
B35 concrete |
|
|
|
|
|
575 cm3/min |
|
|
|
|
|
||
TPS Theft Protection System |
|
|
|
|
|
|
|
|
|
|
|
||
with Company Card, Company Remote and |
|
|
|
|
|
|
|
|
|
||||
TPS-K activation key |
|
|
|
|
option TE 76P / TE 76P-ATC |
|
|
||||||
Noise and vibration information |
|
|
|
|
|
|
|
|
|
|
|
||
(measured in accordance with EN 60745): |
|
TE 76 / TE 76P |
|
TE 76-ATC / TE 76P-ATC |
|||||||||
Typical A-weighted sound power level (LwA): |
|
102 dB (A) |
|
102 dB (A) |
|
||||||||
Typical A-weighted sound pressure level (LpA): |
|
91 dB (A) |
|
|
|
91 dB (A) |
|
For the given sound power level as per EN 60745, the tolerance is 3 dB.
Wear ear protection!
Triaxial vibration value (vibration vector sum) |
|
|
measured in accordance with EN 60745-2-1 prAA: 2005 |
|
|
Drilling in metal, (ah, D) |
2.7 m/s2 |
<2.5 m/s2 |
measured in accordance with EN 60745-2-6 prAB: 2005 |
|
|
Hammer drilling in concrete, (ah, HD) |
17.0 m/s2 |
15.0 m/s2 |
Chiselling, (ah, Cheq): |
15.0 m/s2 |
14.0 m/s2 |
Uncertainty (K) for triaxial vibration value: |
1.5 m/s2 |
1.5 m/s2 |
User information as per EN 61000-3-11:
Switching operations cause short voltage drops. If the mains electric supply conditions are unfavourable, other tools / machines can be impaired. If the main electric supply impedance is less than 0.15 Ohms, no disruptions / disturbances need be expected.
The tool is offered in different versions for various mains voltages. Please refer to the information on the type plate for the nominal voltage and nominal current input of your tool.
13