READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan |
|
||||||
Light Fixture |
Model Numbers: |
||||||
Owner’s Manual |
|||||||
LK150 |
|||||||
|
|
|
|
|
|
||
|
|
|
|
|
|
LK151 |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
Includes: Three 60-Watt |
|
|
|
|
|
|
|
||
|
Net Weight: 2.6 |
Lbs. |
|
||||
|
|
Candelabra Bulbs and Fitter |
|||||
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1.Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for future reference.
2.Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.
3.Do not exceed the wattage indicated on fixture.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1.To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring.
2.Make certain no bare wires are exposed outside the wire connectors.
3.All wiring must conform to national and local electrical codes.
4.Follow the recommended instructions for the proper method of wiring your new light fixture. If you feel you do not have enough electrical wiring knowledge or experience, have your light fixture installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.
WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson CF772 Series Ceiling Fans in indoor locations.
Part No. F40BP74420001 |
Form No. BP7442-1 |
Revision: 130402 |
ETL Model Nos.: LK150 and LK151 |
Assembly and Installation
! WARNING
Do not install or use the light fixture if any part is missing or damaged. Contact your dealer for replacement.
! WARNING
To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.
Installation on Emerson Fans Having a Modular Switch Cup with Center Screw
1.Remove all parts and parts packages from the carton.
2.Remove the switch cup from the cover plate by removing the three screws around the side of the switch cup (Figure 1).
3.Disconnect the motor connector from the switch cup connector (Figure 1).
4.Remove the center screw from the switch cup (Figure 1).
5.Carefully locate the white and blue wires (labeled either "L" or "LIGHT") in the switch cup and remove the wire connectors from the wires.
6.Insert the black and white wires from the light fitter through the center hole in the switch cup (Figure 2) and thread the switch cup onto the light fitter. Hold wires taut while installing switch cup to prevent the wires from twisting. Tighten the fitter until the fan switch chain aligns with the hole in the fitter.
COVER PLATE
MOTOR CONNECTOR
|
SWITCH CUP |
SCREWS |
CONNECTOR |
SWITCH
CUP
CENTER SCREW
Figure 1
7.Insert the black and white wires through the lockwasher and hex nut (supplied), firmly tighten the hex nut to secure the light kit fitter to the switch cup. Connect the white wire from the switch cup to the white wire of the light fitter (Figure 2). Connect the blue wire from the switch cup to the black wire of the light fitter. Use listed wire connectors (previously removed in Step 5) to make connections (Figures 2 and 3).
8.Carefully tuck all wires and splices into the switch cup. (Figure 2.)
9.Connect the motor connector to the switch cup connector.
10.Position the cup/light fitter in the cover plate and install the three screws that were previously removed in Step 2 and tighten securely.
11.Install three 60-watt candelabra base bulbs (supplied) into the light sockets.
MOTOR |
COVER PLATE |
|
|
||
CONNECTOR |
SWITCH CUP |
|
|
||
BLACK WIRE |
CONNECTOR |
|
|
WIRE |
|
BLUE WIRE |
CONNECTOR |
|
|
||
HEX NUT |
WHITE WIRES |
|
SCREWS |
LOCKWASHER |
|
SWITCH CUP |
FAN SWITCH |
|
RUBBER |
CHAIN |
|
|
||
WASHER |
|
|
LIGHT |
|
|
FITTER |
|
|
RUBBER |
|
|
WASHER |
|
|
HEX NUT |
FAN SWITCH CHAIN |
|
|
||
BOWL CAP |
FINIAL (FN200) |
|
(FN200) |
||
|
||
Figure 2 |
|
WARNING: To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.
Figure 3
! WARNING
To avoid possible fire or electric shock, be careful not to pinch wires between switch cup and the cover plate.
2
Loading...