Bosch VEZ Installation And Configuration Manual

AutoDome Easy

VEZ Series

en Installation and Configuration Manual

AutoDome, Bilinx, Bosch, the Bosch logo, DiBos, FastAddress and VIDOS are registered trademarks of Bosch Security Systems, inc.
The following trademarks are registered with the United States Patent and Trademark Office:
Pentium is a registered trademark of Intel Corporation
.NET, DirectX, Internet Explorer, Microsoft, Windows, Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation

Due to the nature of this material, this document refers to numerous hardware and software products by their trade names, In most, if not all
cases, these designations are claimed as trademarks or registered trademarks by their respective companies in the United States of America. It is
not this publisher’s intent to use any of these names generically. The reader is therefore cautioned to investigate all claimed trademark rights be­fore using any of these names other than to refer to the product described.

AutoDome Easy | en iii

Preface

This guide describes how to install the AutoDome Easy.

Audience

This guide is intended for qualified installation and service personnel who are familiar with the applicable national
and local electrical codes.

Document Conventions

Convention Meaning
Bold Denotes a part, item, or assembly.

Italic Denotes a reference to another paragraph, figure or table.
Underline
courier Denotes the actual name of an object, the exact code that should be typed or a message

Symbols

You may encounter these symbols within the document. Explanatory text accompanies each symbol, which provides
additional information detailing the operation or highlighting safety information.

Used to emphasize a point.

returned from a system.

i

!

!

NOTICE! Notices inform you of essential but non-critical information. Read these messages
carefully as any directions or instructions contained therein can help you avoid making
mistakes.

CAUTION! Cautionary messages provide critical information that help you reduce the chance
of losing data or damaging the system. Please heed these messages.

WARNING! Warnings highlight information, that if overlooked may cause damage to the
system or result in personal injury. Take warnings seriously.

DANGER! Danger messages denote the presence of electrical equipment that may cause
electric shock or electrocution. Take care when you see this symbol to avoid serious injury or
death.

Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0

iv en | AutoDome Easy

Customer Support and Service

If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and
shipping instructions.

Service Centers
USA

Phone: [phone] or 585-340-4162
Fax: [phone]
Email: [e-mail]

Technical Support

Phone: [phone]
Email: [e-mail]

CCTV Spare Parts

Phone: [phone] or 408-957-3065
Fax: [phone]
Email: [e-mail]

Canada

Phone: [phone]
Fax: [phone]

Europe, Middle East & Asia Pacific Region

Phone: [phone]
Fax: [phone]
Email: [e-mail]
For additional information, see www.boschsecurity.com

December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.

Safety Precautions | en v

Important Safeguards

1. Read, Follow, and Retain Instructions - All safety and oper­ating instructions should be read and followed before oper­ating the unit. Retain instructions for future reference.

2. Heed Warnings - Adhere to all warnings on the unit and in
the operating instructions.

3. Attachments - Attachments not recommended by the prod­uct manufacturer should not be used, as they may cause
hazards.

4. Installation Cautions - Do not place this unit on an unstable
stand, tripod, bracket, or mount. The unit may fall, causing
serious injury to a person and serious damage to the unit.
Use only manufacturer-recommended accessories, or those
sold with the product. Mount the unit per the manufac­turer's instructions. Appliance and cart combination should
be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart combina­tion to overturn.

5. Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. Generally,
using a damp cloth for cleaning is sufficient. Do not use liq­uid cleaners or aerosol cleaners.

6. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified ser­vice personnel.

7. Damage Requiring Service - Unplug the unit from the main
AC power source and refer servicing to qualified service
personnel under the following conditions:

•When the power supply cord or plug is damaged.

•If liquid has been spilled or an object has fallen into the
unit.

•If the unit has been exposed to water and/or inclement
weather (rain, snow, etc.).

•If the unit does not operate normally, when following the
operating instructions. Adjust only those controls specified
in the operating instructions. Improper adjustment of other
controls may result in damage, and require extensive work
by a qualified technician to restore the unit to normal oper­ation.

•If the unit has been dropped or the cabinet damaged.

•If the unit exhibits a distinct change in performance, this
indicates that service is needed.

8. Replacement Parts - When replacement parts are required,
the service technician should use replacement parts speci­fied by the manufacturer or that have the same characteris­tics as the original part. Unauthorized substitutions may
result in fire, electrical shock or other hazards.

9. Safety Check - Upon completion of servicing or repairs to
the unit, ask the service technician to perform safety
checks to ensure proper operating condition.

10.Power Sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type of
power supply to use, contact your dealer or local power
company.

•For units intended to operate from battery power, refer to
the operating instructions.

•For units intended to operate with External Power Sup­plies, use only the recommended approved power supplies.

•For units intended to operate with a limited power source,
this power source must comply with EN60950. Substitu­tions may damage the unit or cause fire or shock.

•For units intended to operate at 24VAC, normal input volt­age is 24VAC. Voltage applied to the unit's power input
should not exceed 30VAC.
User-supplied wiring, from the 24VAC supply to unit, must
be in compliance with electrical codes (Class 2 power lev­els). Do not ground the 24VAC supply at the terminals or at
the unit's power supply terminals.

11.Coax Grounding - If an outside cable system is connected
to the unit, ensure that the cable system is grounded.
U.S.A. models only - Section 810 of the National Electrical
Code, ANSI/NFPA No.70, provides information regarding
proper grounding of the mount and supporting structure,
grounding of the coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.

12.Grounding - This unit may be equipped with a 3-wire
grounding plug (a plug with a third pin, for grounding). This
safety feature allows the plug to fit into a grounding power
outlet only. If unable to insert the plug into the outlet, con­tact an electrician to arrange replacement of the obsolete
outlet. Do not defeat the safety purpose of the grounding
plug.

•Outdoor equipment should only be connected to the unit's
inputs after this unit has had its grounding plug connected
to a grounded outlet or its ground terminal properly con­nected to a ground source.

•The unit's input connectors must be disconnected from
outdoor equipment before disconnecting the grounding
plug or grounding terminal.

•Proper safety precautions such as grounding should be fol­lowed for any outdoor device connected to this unit.

13.Lightning - For added protection during a lightning storm,
or when this unit is left unattended and unused for long
periods of time, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to
the unit due to lightning and power line surges.

Bosch Security Systems, Inc.

vi en | Safety Precautions

For Indoor Product

1. Water and Moisture - Do not use this unit near water ­for example, in a wet basement, in an unprotected out­door installation or in any area classified as a wet loca­tion.

2. Object and Liquid Entry - Never push objects of any kind
into this unit through openings, as they might touch dan­gerous voltage points or create short circuits, resulting
in a fire or electrical shock. Never spill liquid of any kind
on the unit.

Power Cord and Power Cord Protection - For units
intended to operate with 230VAC, 50Hz, the input and
output power cord must comply with the latest versions
of IEC Publication 227 or IEC Publication 245.

3. Power supply cords should be routed so they are not
likely to be walked on or pinched. Pay particular atten­tion to location of cords and plugs, convenience recep­tacles, and the point of exit from the appliance.

4. Overloading - Do not overload outlets and extension
cords; this can result in a risk of fire or electrical shock.

For Outdoor Product

Power Lines - An outdoor system should not be located
in the vicinity of overhead power lines, electric lights or
power circuits, or where it may contact such power lines
or circuits. When installing an outdoor system, extreme
care should be taken to keep from touching power lines
or circuits, as this contact might be fatal. U.S.A. models
only - refer to the National Electrical Code Article 820
regarding installation of CATV systems.

For Rack-mount Product

1. Ventilation - Do not place this equipment in a built-in
installation or rack, unless proper ventilation is pro­vided, or the manufacturer's instructions were followed.
The equipment must not exceed its maximum operating
temperature requirements.

2. Mechanical Loading - When rack-mounting the equip­ment, ensure that a hazardous condition is not created
by uneven mechanical loading.

Safety Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

This symbol indicates the presence of uninsulated
“dangerous voltage” within the product’s enclo­sure that can cause an electric shock.

This symbol indicates the presence of important
operating and maintenance (servicing) instruc­tions in the literature accompanying the appli­ance.

Installation should be performed by qualified ser­vice personnel only in accordance with the
National Electrical Code or applicable local codes.

Power Disconnect. Units with or without ON-OFF
switches have power supplied to the unit when­ever the power cord is inserted into the power
source; however, the unit is operational only when
the ON-OFF switch is in the ON position. The
power cord is the main power disconnect for all
units.

Modifications

Caution: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.

Bosch Security Systems, Inc.

Safety Precautions | en vii

FCC & ICES INFORMATION

(U.S.A. and Canadian Models Only)

This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, includ-

ing interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules and ICES-003 of Industry Canada. These lim­its are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and
radiates radio frequency energy, and if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equip­ment in a residential area is likely to cause harmful interfer­ence, in which case the user will be required to correct the
interference at his expense.

Intentional or unintentional changes or modifications, not
expressly approved by the party responsible for compliance,
shall not be made. Any such changes or modifications could
void the user’s authority to operate the equipment. If neces­sary, the user should consult the dealer or an experienced
radio/television technician for corrective action. The user may
find the following booklet, prepared by the Federal Communi­cations Commission, helpful: How to Identify and Resolve
Radio-TV Interference Problems. This booklet is available from
the U.S. Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00345-4.

WARNING: This is a Class A product. In a domestic environ­ment, this product may cause radio interference, in which
case, the user may be required to take adequate measures.

Sécurité

Attention : l'installation doit exclusivement être réalisée par du

ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCU­TION, N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PAN­NEAU ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN
COMPOSANT SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILI­SATEUR. CONFIEZ LA RÉPARATION DE L'APPAREIL À DU
PERSONNEL QUALIFIÉ.

Ce symbole signale que le produit renferme une «
tension potentiellement dangereuse » non isolée
susceptible de provoquer une électrocution.

Ce symbole invite l'utilisateur à consulter les
instructions d'utilisation et d'entretien (dépan­nage) reprises dans la documentation qui
accompagne l'appareil.

Attention: l'installation doit exclusivement être
réalisée par du personnel qualifié, conformément
au code national d'électricité américain (NEC) ou
au code d'électricité local en vigueur.

Coupure de l'alimentation. Qu'ils soient pourvus
ou non d'un commutateur ON/OFF, tous les appar­eils reçoivent de l'énergie une fois le cordon
branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque le
commutateur est réglé sur ON. Le débranchement
du cordon d'alimentation permet de couper l'ali­mentation des appareils.

Bosch Security Systems, Inc.

viii en | Safety Precautions

Sicherheitshinweise Precauciones de Seguridad

VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU VER­MEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT
ZU ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN
DIESEM BEREICH, DIE VOM BENUTZER GEWARTET WER­DEN KÖNNEN. LASSEN SIE WARTUNGSARBEITEN NUR
VON QUALIFIZIERTEM WARTUNGSPERSONAL AUS­FÜHREN.

Das Symbol macht auf nicht isolierte „gefährliche
Spannung" im Gehäuse aufmerksam. Dies kann zu
einem elektrischen Schlag führen.

Der Benutzer sollte sich ausführlich über
Anweisungen für die Bedienung und Instandhal­tung (Wartung) in den begleitenden Unterlagen
informieren.

Achtung! Die Installation sollte nur von qualifizier­tem Kundendienstpersonal gemäß jeweils zutref­fender Elektrovorschriften ausgeführt werden.

Unterbrechung des Netzanschlusses. Geräte mit
oder ohne Netzschalter haben Spannung am Gerät
anliegen, sobald der Netzstecker in die Steckdose
gesteckt wird. Das Gerät ist jedoch nur betrieb­sbereit, wenn der Netzschalter (EIN/AUS) auf EIN
steht. Wenn das Netzkabel aus der Steckdose
gezogen wird, ist die Spannungszuführung zum
Gerät vollkommen unterbrochen.

PRECAUCIÓN: PARA DISMINUIR EL RIESGO DE DESCARGA
ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE POS­TERIOR). NO EXISTEN PIEZAS DE RECAMBIO EN EL INTE­RIOR DEL EQUIPO. EL PERSONAL DE SERVICIO
CUALIFICADO SE ENCARGA DE REALIZAR LAS REPARA­CIONES.

Este símbolo indica que existen puntos de tensión
peligrosos sin aislamiento dentro de la cubierta de
la unidad. Estos puntos pueden constituir un
riesgo de descarga eléctrica.

El usuario debe consultar las instrucciones de fun­cionamiento y mantenimiento (reparación) en la
documentación que se suministra con el aparato.

Atención: la instalación la debe realizar única­mente personal cualificado de conformidad con el
National Electric Code o las normas aplicables en
su país.

Desconexión de la alimentación. Las unidades con
o sin interruptores de encendido/apagado reciben
alimentación eléctrica siempre que el cable de ali­mentación esté conectado a la fuente de aliment­ación. Sin embargo, la unidad sólo funciona
cuando el interruptor está en la posición de
encendido. El cable de alimentación es la principal
fuente de desconexión de todas las unidades.

Bosch Security Systems, Inc.

Veiligheidsmaatregelen Sicurezza

Safety Precautions | en ix

VOORZICHTIG: OPEN DE BEHUIZING OF DE ACHTERKANT
VAN HET APPARAAT NIET. ZO VERMINDERT U HET RISICO
OP ELEKTRISCHE SCHOKKEN. IN HET APPARAAT BEVIN­DEN ZICH GEEN ONDERDELEN DIE U ZELF KUNT REPARE­REN. LAAT SERVICE EN ONDERHOUD UITVOEREN DOOR
GEKWALIFICEERD PERSONEEL.

Dit symbool geeft aan dat er binnen in het appa­raat ongeïsoleerde, gevaarlijke spanning aanwezig
is die mogelijk elektrische schokken kan veroorza­ken.

De gebruiker dient de bedienings- en onderhouds­voorschriften te raadplegen in de documentatie
die werd meegeleverd met het apparaat.

Attentie: het apparaat mag alleen door gekwalifi­ceerd personeel worden geïnstalleerd. De instal­latie dient in overeenstemming met de nationale
elektrische richtlijnen of de van toepassing zijnde
lokale richtlijnen te worden uitgevoerd.

Spanning uitschakelen. Apparatuur met of zonder­aan-uitschakelaar staat onder spanning zolang de
stekker is aangesloten op de wandcontactdoos.
De apparatuur is uitsluitend in werking als de aan­uitschakelaar aan staat. Het netsnoer is de "hoofd­schakelaar" voor alle apparatuur.

ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE
ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL PAN­NELLO POSTERIORE). L'UNITÀ NON CONTIENE COMPO­NENTI INTERNI RIPARABILI DALL'UTENTE. PER QUALSIASI
INTERVENTO, RIVOLGERSI A PERSONALE TECNICO QUAL­IFICATO.

Questo simbolo indica la presenza di "tensione
pericolosa" non isolata all'interno del contenitore
del prodotto. Ciò comporta un potenziale rischio
di scosse elettriche.

Si consiglia di consultare le istruzioni operative e
di manutenzione (interventi tecnici) contenute
nella documentazione fornita con il dispositivo.

Attenzione: l'installazione deve essere effettuata
esclusivamente da personale tecnico qualificato in
conformità con il National Electrical Code o con le
normative locali vigenti.

Scollegamento dell'alimentazione. Le unità dotate
o sprovviste di interruttori ON-OFF vengono ali­mentate quando si inserisce il cavo nella presa
dell'alimentazione. L'unità è tuttavia in funzione
solo quando l'interruttore ON-OFF si trova nella
posizione ON. Il cavo di alimentazione costituisce
il dispositivo di scollegamento dell'alimentazione
principale per tutte le unità.

Bosch Security Systems, Inc.

x en | Safety Precautions

Medidas de Segurança Zasady bezpieczenstwa

CUIDADO: PARA REDUZIR O RISCO DE CHOQUE ELÉC­TRICO, NÃO RETIRE A TAMPA (OU A PARTE POSTERIOR).
NO INTERIOR, NÃO EXISTEM PEÇAS QUE POSSAM SER
REPARADAS PELO UTILIZADOR. REMETA A ASSISTÊNCIA
PARA OS TÉCNICOS QUALIFICADOS.

Este símbolo indica a presença de "tensão peri­gosa" não isolada dentro da estrutura do produto,
o que pode constituir risco de choque eléctrico.

O utilizador deve consultar as instruções de funci­onamento e manutenção (assistência) nos docu­mentos que acompanham o aparelho.

Atenção: a instalação deve ser executada apenas
por técnicos qualificados da assistência, de
acordo com o código eléctrico nacional ou os
códigos locais aplicáveis.

Corte de corrente. As unidades com ou sem inter­ruptores ON-OFF (ligar/desligar) recebem cor­rente sempre que o fio de alimentação está
introduzido na fonte de alimentação; contudo, a
unidade apenas está operacional quando o inter­ruptor ON-OFF está na posição ON. O fio de ali­mentação destina-se a desligar a corrente em
todas as unidades.

UWAGA: ZE WZGLEDU NA NIEBEZPIECZENSTWOPORAZE­NIA PRADEM NIE WOLNO OTWIERAC POKRYWY. W
SRODKU NIE MA ZADNYCH ELEMENTÓW, KTÓRE MOGA
BYC NAPRAWIANE PRZEZUZYTKOWNIKA. NAPRAWE
NALEZY POWIERZYCAUTORYZOWANEMU PUNKTOWI SER­WISOWEMU.

Blyskawica ze strzalka wewnatrz trójkata równob­ocznego maza zadanie zwrócic uwage uzytkownika
na obecnoscnieizolowanego “niebezpiecznego
napiecia” wewnatrzobudowy urzadzenia, o wielko­sci stwarzajacejniebezpieczenstwo porazenia pra­dem.

Wykrzyknik wewnatrz trójkata równobocznego ma
zazadanie zwrócic uwage uzytkownika na waznec­zynnosci, zwiazane z obsluga i konserwacja urza­dzenia,zamieszczone w Instrukcji obslugi.

OSTRZEZENIE: ABY UNIKNAC POZARU LUB PORAZENIAPRA­DEM NIE WOLNO WYSTAWIAC NA DZIALANIE DESZCZU LUB
WILGOCI URZADZEN,KTÓRE NIE ZOSTALY ZAPROJEKTOWANE
DO UZYWANIA SPECJALNIE NA OTWARTYM POWIETRZU.

Uwaga: Instalacje urzadzenia powinien wykonac
tylkowykwalifikowany personel, zgodnie z
przepisami NEClub odpowiednimi przepisami mie­jscowymi.

Odlaczanie zasilania. Urzadzenia zarówno nie
posiadajace, jaki posiadajace wylaczniki WL-WYL
znajduja sie podnapieciem, jezeli tylko przewód
zasilajacy jest polaczony zezródlem zasilania. Jed­nakze urzadzenie dziala tylko wtedy, gdywylacznik
znajduje sie w polozeniu WL. Przewódzasilajacy
jestglównym odlacznikiem zasilania dla wszystkich
rodzajówurzadzen.

Bosch Security Systems, Inc.

Safety Precautions | en xi

Bosch Security Systems, Inc.

xii en | Safety Precautions

Bosch Security Systems, Inc.

AutoDome Easy Table of Contents | en xii

Table of Contents

1 Unpacking 1

1.1 Parts List 1

1.2 Additional Tools Required 1

1.3 Safety Rules 2

2Description 3

3 Installing the AutoDome Easy 3

3.1 Mounting the AutoDome Easy 3

4 Preparing the Wiring 4

4.1 Control 4

4.2 Video 4

4.3 Power 4

4.4 Alarm 5

5 Connections 5

5.1 Connecting to the Biphase 5

5.1.1 Direct Control 5

5.1.2 Daisy Chaining 6

5.2 Connecting the Video 7

5.3 Connecting the Power 7

5.4 Connecting the Alarm Input 7

6 Address (ID) 8

6.1 Setting the Address (ID) 8

7 Setting Protocol and Video Format 10

8 Installing the AutoDome Easy 11

8.1 Surface Mount 11

8.1.1 Preparing the Drywall Ceiling for Installation 11

8.1.2 Preparing the Suspension Ceiling for Installation 12

8.1.3 Installing the Base to the Mounting Plate 12

8.1.4 Powering On 13

8.1.5 Installing the Base to a Junction Box 13

9 Basic Operation 14

9.1 Keyboard Control 14

9.2 Command Structure 14

10 Program and Operation 15

10.1 Menu Navigation 15

Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0

xiii en | Table of Contents AutoDome Easy

10.2 Main Menu 15

10.3 Preset Menu 16

10.3.1 Setting and Saving Presets 16

10.3.2 Recalling a Preset Position 17

11 Creating Titles 17

12 Tour Menu 18

12.1 Setting a Tour 18

12.2 Running / Stopping a Tour 19

13 Auto Pan Menu 19

13.1 Set Auto Scans 19

13.2 Run Auto Pan 20

14 Sector Menu 20

15 Alarm Menu 21

15.1 Releasing an Alarm 21

16 Camera Setup Menu 22

16.1 Focus Control Menu 22

16.2 WB Control Menu 23

16.3 AE Control Menu 24

16.4 L/L Control Menu 26

16.5 Picture Menu 27

16.6 Initialize Camera Menu 27

17 Dome Setup Menu 28

17.1 Home Function 29

17.2 Initialize Dome Menu 30

17.3 Dome Information Menu 30

18 Keyboard Commands by Number 31

19 Troubleshooting 32

20 Preventive Maintenance 32

21 Spare Parts List 32

December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.

AutoDome Easy Unpacking 1

1 Unpacking

This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in Section 1.1: Parts List are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.

1.1 Parts List

The AutoDome Easy includes the following components:

• One (1) PTZ Dome (Dome camera)

• One (1) accessory kit including (part number - 9965 300 00648)

One (1) Locking Torx Wrench (T-10)
One (1) Locking Torx Wrench (T-20)
Three (3) tapping screws
Three (3) plastic anchors

• One (1) mounting bracket

• One (1) user manual

1.2 Additional Tools Required

• No. 2 Phillips screwdriver

Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0