Bosch TDA2633GB, TDA2602GB, TDA2622GB Manual

Solving Minor Problems Yourself

Problem	Possible Causes	Solution
	Temperature control (I)	Turn the temperature control to
The iron does	on a very low setting.	the desired position.
not work or is not		Check that the plug is inserted
heating up.	Connection problems.
		into the mains socket correctly.
The clothes tend	Temperature control (I)	Turn the temperature control to
to stick.	setting is too high.	a lower setting.
	Temperature control (I)	Turn the temperature control to
	setting is too low.	a higher setting.
	Steam regulator (A)			calc
	is set too high in	Turn the steam regulator to a
	conjunction with a low	lower setting.
	temperature.
Water comes out	You have pressed the
	shot of steam button	Wait 5 seconds between each
of the soleplate
	(L) repeatedly wihhout	press of the shot of steam
together with
	waiting for 5 seconds	button.
steam.
	between each press.
	Tap or part distilled
	water has not been used	Mix distilled water with tap
	(see“Filling the water	water as directed in the „Filling
	tank“ section) or other	the water tank“ section, and
	products such as fragant	never add any other products
	water have been added	to the water tank.
	to the tank.
	Steam regulator (A) in	Turn the steam regulator to “1”
Iron is not	“0” or “calc” position.	or “2” position.		TDA 26..
	No water in tank.	Fill the tank.
steaming.		Remove the steam regulator		sensixx B1
	Scale obstruction of	(A) and clean it. If this does not
	internal components.	help contact an Authorised
		Technical Service Centre.
Spray does not	No water in the tank.	Add water to the water tank.
		Contact an Authorised
work.	Obstructed mechanism.
		Technical Service Centre.
Water comes
out from the	The steam regulator (A)	Place the steam regulator in the
soleplate before
	is not properly closed.	“0” position.
plugging the
iron in.
Deposits come	Traces of lime scale are	Carry out a cleaning cycle “(see	Customer Service
out through
	coming out of the steam	“Multiple de-scaling system”
the holes in the	chamber.	section)
soleplate.
	During first use: Certain		Great Britain
	components on the		Bosch Customer Service
The iron begins	appliance have been
		This is completely normal and	Grand Union House
to smoke when	lightly greased at
		will stop after a short while.
switched on.	the factory and may		Old Wolverton Road
	produce a little smoke		Milton Keynes	Operating instructions
	when initially heated.
		Move the iron gently fromside	MK12 5PT
Flashing lamp on	Auto-shut off has been	to side to re-start it.	UK [phone]
top of handle (*)	activated.	The lamp will then flash once	IRL [phone]
		before it re-heats.	www.bosch-home.co.uk
(*) Model dependent
You can download this manual from the local homepages of Bosch				003 TDS26..GB/01/12

Thank you for buying the TDA26 steam iron from Bosch. This iron has a lightweight design and is built to perform.

These instructions contain valuable information about the unique features of this iron and some hints to make ironing easier for you.

Please visit www.bosch-home.co.uk for more product information or to register your product, just follow the link to the Online guarantee registration.

Before using the Iron for the first time

Please carry out the following steps:

1.Remove the protective cover from the soleplate before using the iron.

2.While the iron is unplugged, fill the water tank (E) with tap water and set the temperature control (I) to “max” by lining it up with the pointer

3.Plug the appliance into the mains and when the iron has reached the correct temperature (the pilot light [K] goes out), set the steam regulator

(A)to the “2” position.

4.Hold the iron horizontally and repeatedly press the shot of steam button

(L).Any residue should come out of the soleplate (G). It may smoke and smell – this is normal and will cease after a short while.

5.If necessary, carefully clean the soleplate down with a dry, folded cloth.

Cleaning and Maintenance

! Attention! Risk of burns!

For general cleaning, follow the information below:

	Problem	Solution
	Dirty/lightly marked iron	Clean the body of iron or soleplate with a
	body or soleplate	damp cloth then dry it..
	Mark develops on	Set the iron to its maximum temperature
		setting. Rub the iron a few times over with
	soleplate during use
		a dry cotton cloth folded several times.
		While the iron is cold, iron a linen cloth
	Heavily stained soleplate	soaked in white vinegar. Then dampen a
		cloth with water and wipe the soleplate
		clean and dry thoroughly.

DO NOT de-scale or clean the water tank with cleaning products or solvents, as these could cause the iron to drip when using the steam function.

DO NOT use a “professional steam cleaner” for cleaning the appliance.

DO NOT use sharp objects or abrasive products to clean the soleplate or any other part of the appliance. To keep the soleplate in good condition, do not allow it to come into contact with metal objects.

GUARANTEE TERMS

The terms of the guarantee for this appliance are in accordance with that stated by our representative for the country in which it is sold. Details of those conditions can be obtained from the retailer from whom the appliance was purchased. The SALES RECEIPT must be presented when making any claims against the terms of this guarantee. We reserve the right to make technical modifications.

Environmental Care

This iron has been designed according to ecological criteria related to sustainable development; analysing its whole lifecycle, from material selection to its later reuse or recycling; evaluating the improvement possibilities from a technical, ecological and environmental point of view.

Before throwing a used appliance away, you should make it noticeably inoperable e.g. cut off the mains lead and be certain to dispose of it in accordance with current laws and regulations.

Your retailer, town council or local council can give you detailed information about these.

This appliance is labelled in accordance with European Directive 2002/96/EG concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE).

The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Important

This appliance has been designed exclusively for domestic use and must not be used for industrial purposes.

Carefully read through these instructions and safeguard them for future reference.

General safety instructions

•Danger of electric shocks or fire!

•This appliance is to be connected and used in accordance with the information stated on its characteristics plate.

•This appliance must be connected to an earthed socket. If it is absolutely necessary to use an extension cable, make sure that it is suitable for 16A and has a socket with an earth connection.

•The iron should not be used if it has been dropped, if there are visible signs of damage or if it is leaking water. It must be checked by an authorized Technical Service Centre before it can be used again.

•Do not allow the power cable to come into contact with the soleplate when it is hot.

•In order to avoid that, under unfavourable mains conditions, phenomena like transient voltage drops or lighting fluctuations can happen, it is recommended that the iron is connected to a power supply system with a maximum impedance of 0.27Ω . If necessary, the user can ask the public power supply company for the system impedance at the interface point.

•This appliance is not intended to be used by persons (including children) with reduced physical, sensory or mental capacities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

•Keep the appliance out of children’s reach.

•Children should be supervised to ensure that they do not play with the appliance.

•Remove the plug from the socket before filling the appliance with water or before pouring out the remaining water after use.

•The appliance must never be placed directly under the tap to fill the water tank.

•The appliance must be used and placed on a stable surface.

•When placed on its stand, make sure that the surface on which the stand is placed is stable.

•The iron must not be left unattended while it is connected to the supply mains.

•Unplug the appliance from the mains supply after each use, or if a fault is suspected.

•The electrical plug must not be removed from the socket by pulling the cable.

•Never immerse the iron in water or any other fluid.

•Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc.)

•With the aim of avoiding dangerous situations, any work or repair that the appliance may need, e.g. replacing a faulty mains cable, must only be carried out by qualified personnel from an Authorised Technical Service Centre.