Alpine DVI-9990 User Manual
Guide for Installation and Connections
Guide d’installation et de connexions
Guía de instalación y conexiones
Sankei Kikaku Co., Ltd.
Hino, Tokyo, Japan
ALPINE ELECTRONICS MARKETING, INC.
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
ALPINE ELECTRONICS OF CANADA, INC.
7300 Warden Ave., Suite 203, Markham,
Ontario L3R 9Z6, Canada
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
Victoria 3173, Australia
ALPINE ELECTRONICS GmbH
Frankfurter Ring 117, 80807 München,
ALPINE ELECTRONICS OF U.K. LTD.
Coventry CV4 9TW, U.K.
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280) 98, Rue de la Belle Etoile, Z.I. Paris Nord II, B.P. 50016, 95945 Roissy Charles de Gaulle Cedex, France Phone
ALPINE ITALIA S.P.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32 01013 Vitoria (Alava) - APDO 133, Spain Phone
Designed by ALPINE Japan Printed in Japan (S)
GUIDE FOR INSTALLATION AND CONNECTIONS
•Please read this GUIDE FOR INSTALLATION AND CONNECTIONS and the OWNER’S MANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope that your new
In case of problems when installing your unit, please contact your authorized ALPINE dealer.
Points to Observe for Safe Usage
•Read this manual carefully before starting operation and use this system safely. We cannot be responsible for problems resulting from failure to observe the instructions in this manual.
•This manual uses various pictorial displays to show how to use this product safely and to avoid harm to yourself and others and damage to your property.
Here is what these pictorial displays mean. Understanding them is important for reading this manual.
•Meaning of displays
This symbol means important instructions. Failure to heed them can
result in serious injury or death.
This symbol means important instructions. Failure to heed them can
result in injury or property damage.
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up inside and may result in fire.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT. Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
•Be sure to disconnect the cable from the
•Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle’s electrical system.
•When making connections to the vehicle’s electrical system, be aware of the factory installed components (e.g.
Connections with other equipments
•To use this unit, a Multimedia Manager
Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.
PLACE OF PURCHASE:
To prevent external noise from entering the audio system.
•Locate the unit and route the leads at least 10 cm away from the car harness.
•Keep the battery power leads as far away from other leads as possible.
•Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
•If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors. Contact them for further information.
•Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
S video cable
(M5 x 6)
Parts for remote control
Reinforcement screw Remote control holder
(M3 x 12)
Before deciding on the mounting location, check that opening and closing the display will not hamper gear shifting in that position.
• Install at an angle of within 35 degrees from the horizontal.
Mounting Sleeve (Included)
Remove the Detachable Front Panel (refer to page 9 of Owner’s Manual). Remove the front frame from main unit (see “Removal” on page 7).
Slide the mounting sleeve into the dashboard.
Hex Nut (M5)
Reinforce the head unit with the metal mounting strap (not supplied). Secure the ground lead of the unit to a clean metal spot using a screw ( ) already attached to the vehicle’s chassis.
For the screw marked , use an appropriate screw for the chosen mounting location.
Connect each input lead coming from the product you are connecting with to the corresponding output lead coming from the left rear of the
1Remove the DETACHABLE FRONT PANEL.
2Use a small screwdriver (or similar tool) to push the locking pins to the “up” position (see above drawing). As each pin is unlocked, gently pull out on the unit to make sure it does not
3Pull the unit out, keeping it unlocked as you do so.
< JAPANESE CAR >
Screws (M5 x 6)
Secure the ground lead of the unit to a clean metal spot using a screw ( ) already attached to the vehicle's chassis.
Mounting the remote control holder
•If the remote control is in direct sunlight, remove it from the holder and keep it in the glove box.
•When the holder cannot be mounted securely with Velcro tape, mount it by using screws.
Console Box etc.
• Basic Connection
• Video output connector
Outputs a video signal.
Connects to the video input of the TV monitor you are linking with.
•There is a copy protect signal included in the video output signal, so that recording with a VCR (Video Cassette Recorder) etc., is not possible.
Also, depending on the monitor, the picture may not be displayed correctly.
Connects with IONBUS compatible products.
•S video output terminal
Outputs a video signal.
Connects with ALPINE products with a S video input terminal.
•DVD Audio Link terminal
Connects with the DVD Audio Link terminal of the
(Connect when using a DVD audio disc. Remove the terminal cover and plug in the DVD Audio Link cable).
• Power Antenna Lead
Connect this lead to the +B terminal of your power antenna, if applicable.
• Illumination Lead
Orange This lead may be connected to the vehicle’s instrument cluster illumination lead. This will allow the backlighting of the
Power supply unit
Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.
•Switched Power Lead (Ignition)
Connect this lead to an open terminal on the vehicle’s fuse box or another unused power source which provides (+)12V only when the ignition is turned on or in the accessory position.
• Battery Lead
Connect this lead to the positive (+) post of the vehicle’s battery.
•Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the air conditioner. This may cause a malfunction.
•Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system.
•The power supply unit temperature can become hot. This is not a malfunction.