03_SEQUOIA_U (L/O 0301)
Foreword
Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build.
This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully.
When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require.
If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number:
D U.S. OWNERS: |
Toyota Customer Assistance Center |
Toll−free: |
1−800−331−4331 |
D CANADIAN OWNERS: |
Toyota Canada Customer Interaction Centre |
Toll−free: |
1−888−TOYOTA−8 (1−888−869−6828) |
Please leave this Owner’s Manual in this vehicle at the time of resale. |
The next |
owner will need this information also. |
|
All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice.
Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle.
♥ 2003 TOYOTA MOTOR CORPORATION
All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.
i
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Important information about this manual
Safety and vehicle damage warnings |
Safety symbol |
Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or damage.
The types of warnings, what they look like, and how they are used in this manual are explained as follows:
CAUTION
This is a warning against anything which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to reduce the risk of injury to yourself and others.
NOTICE
This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.
When you see the safety symbol shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.
ii
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Important information about your Toyota
New vehicle warranty
Your new vehicle is covered by the following Toyota limited warranties:
DNew vehicle warranty
DEmission control systems warranty
DOthers
For further information, please refer to the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.
Your responsibility for maintenance
It is the owner’s responsibility to make sure that the specified maintenance is performed. Section 6 gives details of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
iii
Accessories, spare parts and modification of your Toyota
A wide variety of non−genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Spark ignition system of your
Toyota
The spark ignition system in your Toyota meets all requirements of the Canadian Interference−Causing Equipment Standard.
Installation of a mobile two−way radio system
As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system/sequential multiport fuel injection system, electronic throttle control system, cruise control system, anti−lock brake system, traction control system (two−wheel drive models)/active traction control system (four−wheel drive models), vehicle skid control system, SRS airbag system and seat belt pretensioner system, be sure to check with your Toyota dealer for precautionary measures or special instructions regarding installation.
iv
Scrapping of your Toyota
The SRS airbag and front seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and pretensioners left
as they are, this may |
cause an accident such as fire. |
Be sure to have the |
systems of the SRS airbag and |
seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you dispose of your vehicle.
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
On−pavement and off−road driving tips
This vehicle belongs to the utility vehicle class. Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle will handle and maneuver differently from an ordinary passenger car because it is designed for off−road use also. In addition, this vehicle has a higher ground clearance and center of gravity than that of an ordinary passenger car. This vehicle design feature causes this type of vehicle to be more likely to rollover. Failure to operate this vehicle
correctly may result in loss of |
control, accidents or |
vehicle rollover causing death or |
serious injury. Be sure |
to read “Off−road vehicle precautions” on page 282 in Section 2 and “Off−road driving precautions” on page 301 in Section 3.
v
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
vi
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
SECTION 1− 1
OPERATION OF INSTRUMENTS AND CONTROLS
Overview of instruments and controls
Instrument panel overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Instrument cluster overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Indicator symbols on the instrument panel . . . . . . . . . . . . . . . . . . . . . . . 7
1
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Instrument panel overview
1. Side vents
2. Instrument cluster
3. Center vents
4. Multi−information display
5. Personal lights
6. Garage door opener box or auxiliary box
7. Electric moon roof switches
8. Side defroster outlet
9. Glove box
10. Power door lock switches
11. Power window switches
12. Power outlets
13. Seat heater switches
14. Rear console box
15. Rear air conditioning controls
16. Headphone input jacks
17. Input terminal adapter
18. Cup holders
19. Power rear view mirror control switches
20. Front drive control lever
21. Lower vent
2
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
22.Hood lock release lever
23.Parking brake pedal
24.Window lock switch
3
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
1. Power back window switch
2. Power outlet main switch
3. Headlight and turn signal switch, and front fog light switch
4. Wiper and washer switches
5. Automatic transmission selector lever
6. Emergency flasher switch
7. Car audio
8. Air conditioning controls
9. Front passenger’s seat belt reminder light
10. Back window and rear view mirror defogger switch
11. Clock
12. Cup holder
13. Center differential lock switch (four−wheel drive models)
14. “TRAC OFF” switch (two−wheel drive models)
15. “4WD” switch
16. Ashtray
17. Cigarette lighter
18. Cruise control switch
19. Ignition switch
4
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
20.Audio remote control switches
21.Tilt steering lock release lever
22.Instrument panel light control knob
5
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Instrument cluster overview
1. |
Oil pressure gauge |
4. |
Speedometer |
7. |
Trip meter reset knob |
2. |
Service reminder indicators and |
5. |
Volt meter |
8. |
Odometer and two trip meters |
|
indicator lights |
6. |
Fuel gauge |
9. |
Engine coolant temperature gauge |
|
|
||||
3. |
Tachometer |
|
|
|
|
6
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
Indicator symbols on the instrument panel
Brake system warning light 1
Driver’s seat belt reminder light 1
Front passenger’s seat belt reminder light 1
Discharge warning light 1
Malfunction indicator lamp 1
Low fuel level warning light 1
or |
Anti−lock brake system warning light 1 |
03_SEQUOIA_U (L/O 0301)
Vehicle skid control system/traction control system (two−wheel drive models) or active traction control system (four−wheel drive models) warning light 1
Open door warning light 1
SRS warning light 1
Unengaged “Park” warning light 1
Automatic transmission fluid temperature warning light 1
Low windshield washer fluid level warning light 1
Engine immobiliser/theft deterrent system indicator light
7
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Turn signal indicator lights
Headlight high beam indicator light
Overdrive−off indicator light
Automatic transmission indicator lights
Four−wheel drive and center differential lock indicator lights
Slip indicator light
Traction control system off indicator light (two−wheel drive models)
Vehicle skid control system off indicator light (four−wheel drive models)
Cruise control indicator light 2
1: For details, see “Service reminder indicators and warning buzzers” on page 134 in Section 1−5.
2: If this light flashes, see “Cruise control” on page 159 in Section 1−6.
8
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
SECTION 1− 2
OPERATION OF INSTRUMENTS AND CONTROLS
Keys and Doors
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Engine immobiliser system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Side doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power back window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Back door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Theft deterrent system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Fuel tank cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Electric moon roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
Keys
Your vehicle is supplied with the two kinds of keys.
1.Master keys (black)—These keys work in every lock. Your Toyota dealer will
need it to |
make you |
a new key with |
a built−in |
transponder |
chip. |
2.Sub key (gray)—This key also works in every lock.
A transponder chip for engine immobiliser system has been placed in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.
10
03_SEQUOIA_U (L/O 0301)
Since the side doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.
NOTICE
When using a key containing a transponder chip, observe the following precautions:
z When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
zWhen starting the engine, do not use the key with other transponder keys around (including keys of other vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after removing other transporter keys (including keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.
z Do not bend the key grip.
zDo not cover the key grip with any material that cuts off electromagnetic waves.
zDo not knock the key hard against other objects.
zDo not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.
zDo not put the key in water or wash it in an ultrasonic washer.
zDo not use the key with electromagnetic materials.
11
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Engine immobiliser system
KEY NUMBER PLATE
Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle.
If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.
We recommend writing down the key number and storing it in a safe place.
12
The engine immobiliser system is a theft prevention system. When you insert the key in the ignition switch, the transponder chip in the key’s head transmits an electronic code to the vehicle. The engine will start only when the electronic code in the chip corresponds to the registered ID code for the vehicle.
The system is automatically set when the key is removed from the ignition switch. The indicator light will start flashing to show the system is set.
If any of the following indicator conditions occurs, contact your Toyota dealer.
D The indicator light stays on except when the theft deterrent system is setting or activating. (See “Theft deterrent system” on page 32 in this section.)
DThe indicator light does not start flashing when the key is removed from the ignition switch.
DThe indicator light flashes unsteady.
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off.
For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you.
If you make your own duplicate key, you will not be able to cancel the system or start the engine.
NOTICE
Do not modify, remove or disassemble the engine immobiliser system. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.
For vehicles sold in U.S.A.
FCC ID: MOZ RI−4ETY
MADE IN JAPAN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For vehicles sold in Canada
This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
13
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
Side doors
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
All the side doors and back door lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice in succession will unlock all the side doors and back door simultaneously.
03_SEQUOIA_U (L/O 0301)
This double key turning operation to unlock all the side doors and back door can be changed to a single key turning operation. For details, contact your Toyota dealer.
When all the side doors and back door are unlocked simultaneously using a key, the interior light, luggage compartment light, ignition switch light and foot light will come on and remain on for about 15 seconds before fading out. (For details, see “Center interior and personal lights” on page 121, “Center interior light” on page 122, “Luggage compartment light” on page
123 |
and “Ignition switch light” on page |
124 |
in Section 1−4.) |
The windows and electric moon roof can be opened or closed with the key operation in the driver’s door keyhole. (For details, see “Power windows” on page 24 and “Electric moon roof” on page 35 in this section.)
LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward. To unlock: Pull the knob backward.
The front doors can be opened by pulling the inside handles even if the lock knobs are in the locked position.
14
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
CAUTION
Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.
Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the vehicle.
Doors cannot be locked when either front door is open and the key is in the ignition.
Driver’s side
Passenger’s side
LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch down on the front side.
To unlock: Push the switch down on the rear side.
All the doors lock or unlock simultaneously.
When the front doors are locked from the outside or locked with the wireless remote control transmitter, the power door lock switch will not work until either front door is unlocked with the key, lock knob, or wireless remote control transmitter.
If the vehicle is subjected to a severe impact from the front or rear, or from either side with the ignition switch at the “ON” position, all the door locks are automatically cancelled.
15
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
REAR DOOR CHILD−PROTECTORS
Move the lock lever to the “LOCK” position as shown on the label.
This feature allows you to lock a rear
door so it can |
be opened from the outside |
|
only, not from |
inside. We recommend us- |
|
ing |
this feature whenever small children |
|
are |
in the vehicle. |
|
16
03_SEQUOIA_U (L/O 0301)
CAUTION
Before driving, be sure that the doors are closed and locked, especially when small children are in the vehicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the vehicle during an accident. It also helps prevent the doors from being opened unintentionally.
—Automatic door locking and unlocking functions
You can select the following modes of the automatic locking and unlocking functions. The initial mode is mode 1.
DMode 1—Automatic locking operation linked to shift lever position
All doors are automatically locked when the shift lever is moved out of “P” position after the ignition switch is turned to the “ON” position and all the doors are closed.
DMode 2—Automatic locking operation linked to vehicle speed
All doors are automatically locked when the vehicle speed goes above about 20 km/h (12 mph).
DMode 3—Automatic unlocking operation linked to the ignition switch
All doors are automatically unlocked
when the driver’s door is opened within 10 seconds after the ignition switch is turned to the “ACC” or “LOCK” position, or the key is removed.
DMode 4—Automatic unlocking operation linked to shift lever position
All doors are automatically unlocked when the selector lever is moved to “P” position after the ignition switch is turned to “ON” position.
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
SETTING FUNCTIONS
You can set the following functions by yourself.
To set the mode 1 (the automatic locking operation linked to shift lever position):
1.Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2.Shift the selector lever into the “P” position.
3.Within 10 seconds of turning the ignition switch to the “ON” position, press and hold the front of the driver’s side power door lock switch for 5 seconds and then release it.
4.The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above operation again.
To set the mode 2 (the automatic locking operation linked to vehicle speed):
1.Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2. Shift |
the |
selector lever from the “P” |
into |
the |
“N” position. |
3.Within 10 seconds of turning the ignition switch to the “ON” position, press and hold the front of the driver’s side power door lock switch for 5 seconds and then release it.
4.The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above operation again.
To set the mode 3 (the automatic unlocking operation linked to the ignition switch):
1.Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2. Shift |
the |
selector lever from the “P” |
into |
the |
“N” position. |
3.Press the driver’s side power door lock switch on the rear side for about 5 seconds, within 10 seconds after the ignition switch is turned to the “ON” position.
4.The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above operation again.
To set the mode 4 (the automatic unlocking operation linked to shift lever position):
1.Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2.Shift the selector lever into the “P” position.
3.Within 10 seconds of turning the ignition switch to the “ON” position, press and hold the rear of the driver’s side power door lock switch for 5 seconds and then release it.
4.The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above operation again.
CAUTION
To prevent an accident, set and cancel the function with the parking brake set securely.
17
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
—Wireless remote control
Locking operation
Unlocking operation
18
03_SEQUOIA_U (L/O 0301)
The wireless remote control system is designed to lock or unlock all the side doors and back door, open the back window or activate the “PANIC” mode from a distance within approximately 1 m (3 ft.) of the vehicle.
LOCKING AND UNLOCKING THE SIDE DOORS AND BACK DOOR
To lock and unlock all the side doors and back door, push the switches slowly and securely.
To lock: Push the “LOCK” switch. All the side doors and back door are locked simultaneously. At this time one beep will be heard, and the parking lights and tail lights flash once.
Check to see that all the side doors and back door are securely locked.
If any of the side doors or back door is not securely closed, locking cannot be performed by the “LOCK” switch and a beep will sound continuously for 10 seconds. However, if the key is in the ignition, a beep will not sound.
To stop the beep, close all the side doors and back door securely or push the “UNLOCK” switch.
The beep can be disabled. For details, contact your Toyota dealer.
To unlock: Push the “UNLOCK” switch once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights and tail lights flash twice.
This double switch operation to unlock all the side doors and back door can be changed to a single switch operation. For details, contact your Toyota dealer.
When all the side doors and back door are unlocked simultaneously with a wireless remote control transmitter, the interior light, luggage compartment light, ignition switch light and foot light come on for about 15 seconds and then fade out, even if the door is not opened. (For details, see “Center interior and personal lights” on page 121, “Center interior light” on page 122, “Luggage compartment light” on page 123 and “Ignition switch light” on page 124 in Section 1−4.)
You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will be automatically locked again.
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
The timing for the automatic door lock function can be changed. For details, contact your Toyota dealer.
If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking operation is not repeated. Release the switch and then push again.
The wireless door locking or unlocking function can be erased. For details, contact your Toyota dealer.
SWITCHING BEEP SOUND ON AND OFF
You can switch the beep on and off. (The beep is on initially and after battery replacement.)
To switch the beep on and off:
With the driver’s door opened—
1. |
Insert |
the |
ignition key and remove it. |
2. |
Within |
5 |
seconds, insert the ignition |
|
key again |
and turn it to the “ON” posi- |
|
|
tion. |
|
|
3.After 10 seconds, push the same “LOCK”, “UNLOCK”, “PANIC” switch or back window open button twice within 10 seconds.
Two beep sounds inform you that the program has been switched on or off.
If this procedure |
is not |
followed exactly, |
the beep will not |
operate |
as expected. |
Check the beep ON/OFF operation by pushing the transmitter switch after you finish this procedure. If the beep does not operate as expected, repeat this procedure from step 1.
OPENING THE BACK WINDOW
To open the back window, push the back window open switch of the transmitter for about 1 second. The window will fully open.
At this time, you can hear a beep.
If the ignition switch is in the “ON” position, the back window cannot be opened by the back window open switch.
To open the back window with the master key, see “Power back window” on page 27 in this section.
The back window opening program by wireless remote control can be changed or disabled. For details, contact your Toyota dealer.
19
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
“PANIC” SWITCH
Pushing the “PANIC” switch blows the horn intermittently and flashes the headlights and tail lights.
The “PANIC” switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehicle.
The alarm will last for one minute. To stop alarm midway, push the “PANIC” or “UNLOCK” switch, or unlock any side door or back door with key. You can also stop the alarm by turning the ignition key from “LOCK” to the “ON” position.
The “PANIC” mode does not work when the ignition key is in the “ON” position.
This alarm function can be disabled. For details, contact your Toyota dealer.
WIRELESS REMOTE CONTROL TRANSMITTER
The wireless remote control transmitter is an electronic component. Observe the following instructions in order not to cause damage to the transmitter.
DDo not leave the transmitter on places where the temperature becomes high such as on the dashboard.
DDo not disassemble it.
DAvoid knocking it hard against other objects or dropping it.
DAvoid putting it in water.
You can use up to 4 wireless remote control transmitters for the same vehicle. Contact your Toyota dealer for detailed information.
If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance:
DCheck for closeness to a radio transmitter such as a radio station or an airport which can interfere with normal operation of the transmitter.
DThe battery may have been consumed. Check the battery in the transmitter. To replace the battery, see following “REPLACING THE BATTERY”.
If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 335 in Section 4.)
20
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
For vehicles sold in U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
DReorient or relocate the receiving antenna.
DIncrease the separation between the equipment and receiver.
DConnect the equipment into an outlet
on a |
circuit different |
from that to |
which |
the receiver is |
connected. |
DConsult the dealer or an experienced radio / TV technician for help.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
21
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
For vehicles sold in Canada
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
REPLACING THE BATTERY
For replacement, use a CR2016 lithium battery or equivalent.
CAUTION
Special care should be taken to prevent small children from swallowing the removed battery or components.
NOTICE
zWhen replacing the transmitter battery, be careful not to lose the components.
zReplace only with the same or equivalent type recommended by a Toyota dealer.
zDispose of used batteries according to the local laws.
Replace the battery by following these procedures:
1.Using a coin or equivalent, open the transmitter case.
22
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
03_SEQUOIA_U (L/O 0301)
2.Remove the discharged transmitter battery.
NOTICE
Do not bend the terminals.
3.Put a new transmitter battery with positive (+) side up.
Close the transmitter case securely.
NOTICE
zMake sure the positive side and negative side of the transmitter battery are faced correctly.
zDo not replace the battery with wet hands. Water may cause unexpected rust.
zDo not touch or move any compo-
nents inside of the transmitter, or it may interfere with proper operation.
zBe careful not to bend the electrode of the transmitter battery insertion and that dust or oils do not adhere to the transmitter case.
zClose the transmitter case securely.
After replacing the battery, check that the transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
23
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
Power windows
Window lock switch
Driver’s door switches
03_SEQUOIA_U (L/O 0301)
OPERATING FROM INSIDE
The windows can be operated with the switch on each side door.
The power windows work when the ignition switch is in the “ON” position.
Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either front side door is opened.
OPERATING THE DRIVER’S AND FRONT PASSENGER’S WINDOWS
Use the switches on the driver’s door and front passenger’s door.
Normal operation: The window moves as long as you hold the switch.
To open: Lightly push down the switch. To close: Lightly pull up the switch.
If you push in the window lock switch on the driver’s door, the passenger’s window cannot be operated.
Driver’s door switches
Front passenger’s door switch |
Front passenger’s door switch |
24
2003 SEQUOIA from Jan. ’03 Prod. (OM34422U)
Loading...