Samsung SCC-B5366P, SCC-B5368P, SCC-B5366B, SCC-B5366SBP, SCC-B5368BP Manual

SCC-B5366 SCC-B5368 SCC-B5366S SCC-B5368S

DIGITAL COLOR DOME

CAMERA

ENG

user manual

FRE

GER

SPA

imagine the possibilities	ITA
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at

www.samsungsecurity.com

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

•To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

2 – DIGITAL COLOR DOME CAMERA

Safety information

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

CAUTION

	1.	Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to
		excessive vibrationor magnetic interference.
	2.		ENG
		Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high
		humidity. Doing so may cause fire or electric shock.
	3.	If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall
		it.
	4.	Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or
		damage to the product.
	5.	Keep out of direct sunlight and heat radiation sources. It may cause fire.
	6.	Install it in a place with good ventilation.
	7.	Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
		CCD image sensor.
	8.	Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
		shall be placed on the apparatus.
	9.	The Mains plug is used as a disconnect device and shall stay readily operable at any time.

English – 3

Important Safety Instructions

WARNING

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

13.Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4 – DIGITAL COLOR DOME CAMERA

	Contents
Introduction
Features		6
Product & Accessories		7
Part Names and Functions		8
Installation
Before installation		11
Installation procedure		11
Adjusting the camera direction		13

How to use OSD Menu	ENG
Using Icons in the Menu	14
Main Menu	14
Profile	15
Camera Setup	17
Intelligence	24
Privacy Zone Setup	27
Other Set	28
System Information	29
Language	29
Specifications
Specifications	30

English – 5

Introduction

FEATURES

High Resolution

•This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special algorithm technologies.

Intelligent Motion Detection & Tracking

•This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it displays an alert if an object passes / enters /exits the virtual fence or virtual area.

XDR (eXtended Dynamic Range)

•Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

High Sensitivity

•It implements images of high sensitivity using the up-to-date SONY Super-HAD IT CCD..

Low Illumination

•It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera identify objects even in the worst environment.

Superior Backlight Adjustment

•When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object picture quality.

Digital Power Synchronization

•The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the operationability and reliability of this camera.

Output Signal Setting

•You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling, and digital zooming.

OSD(On Screen Display) Menu

•OSD menu is provided to display the status of camera and to configure the functions interactively.

6 – DIGITAL COLOR DOME CAMERA

Introduction

Coaxial Cable Communication

•This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the control signal. In installation or repair, this helps you control the communication controller (optional) without additional cabling.

PRODUCT & ACCESSORIES

Product & Accessories

• Main Product

ENG

Camera

• Accessories

Test Monitor Cable

Tab screw

User’s Manual

Note :

–The test monitor cable is used to test the camera by connecting to a portable display. If you really want to connect the camera to a monitoring display, use the BNC cable.

English – 7

Introduction

PART NAMES AND FUNCTIONS

Components of your camera

Test monitor output

Lens

Video connector

Power connector

8 – DIGITAL COLOR DOME CAMERA

		Introduction
No	Name	Brief description
1	Cover dome	Covers the inner cover, lens, and main body to protect them.
2	Inner cover	Covers the main body to protect it.
3	Wing locker	Push a long thin screwdriver into its narrow spot and press it outward when you want to
		remove the inner cover.
4	Main body	Includes a lens, a switch board, a PCB board, screws, and such.
5	Mount bracket	Used as a ceiling or wall fixture. It is fixed using three long tab screws provided in the
		package.
6	Wiring Passage	This passage is designed to make arrangement of the cables if you drill a hole to extend the wiring.
7	Zoom lever	Using this lever, the lens zoom can be adjusted and fixed.	ENG
8	Focus lever	The lens focus can be adjusted by rotating it left or right. Rotate it clockwise for fixing.
9	Tilt fixing screw	Using this screw, the slope of the lens can be adjusted and fixed.
10	4-way Switch	This switch is used to set and adjust the settings of the camera’s functions.
11	Groove mark	To attach the Main body to the Mount bracket, align this groove mark on the Main body with
		the wide groove in the CAMERA FRONT side on the Mount bracket.
12	Locker	Used to open or close the Cover dome. To open the cover dome, press the locker.
		Push it outward and rotate the main body in UNLOCK direction when you want to remove
13	Lock releaser	the Mount bracket from the Main body or to remove the installed camera from the Mount
		bracket.
14	Cable	Connect the Video connector to BNC cable and Power connector to power adapter.

English – 9

Introduction

Setting switches

• SETUP Switch

This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the MAIN MENU appears.

ef(Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the displayed value.

cd(Up/Down) : By pressing this switch up or down, you can move up or down on the menu.

: When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press this button..

10 – DIGITAL COLOR DOME CAMERA

Installation

BEFORE INSTALLATION

Before installing your camera, you have to read the following cautions.

•You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.

•Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or fire.

•When installing your camera, don’t allow any person to approach the installation site. If you have any valuable things under the place, move them away.

INSTALLATION PROCEDURE

ENG

English – 11

Installation

Press the Locker button on the bottom of your camera and remove the Cover dome from the Main body using the other hand. The Main body and Inner cover will be exposed to you.

To install and adjust your camera, you have to first remove the Inner cover. To remove the Inner cover from the Main body, push a long thin screwdriver into the narrow spot of the Wing locker and press it outward to remove the cover.

Remove the Mount bracket from the Main body by rotating the Main body in the UNLOCK direction while pushing the Lock releaser outward. If it is not easily done, rotate the Mount bracket in the LOCK direction while holding small holes on the Mount bracket.

Fix the Mount bracket to the location (ceiling or wall) with supplied three screws.

Note :

–The CAMERA FRONT sign on the Mount bracket should face the camera monitoring area.

Extend the wiring up to the ceiling or wall through the bracket.

Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning the Groove mark on the Main body with the wide groove around the CAMERA FRONT inlay.

Adjust the camera direction. For more details on the direction control, see “Adjusting the camera direction,” on the same page. When required to adjust the zoom and focus for your camera, see “Connecting cables and changing the settings,” on page 10.

Attach the Inner cover to the Main body by pressing it until a “click” sound is heard after aligning two screw holes on the Wing lockers of the Inner cover with two screw holes on the Main body’s left and right sides.

Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard after aligning the bump inside the Cover dome with the Groove mark on the Main body.

12 – DIGITAL COLOR DOME CAMERA

Installation

ADJUSTING THE CAMERA DIRECTION

When the camera is fixed on the ceiling, you can adjust the camera viewing angle. You can rotate your camera leftward or rightward (Panning), and can change the slope of your camera upward or downward (Tilting).

In case of panning, the rotation limit of your camera is set to 355 degree (100 degree clockwise and 255 degree counterclockwise). The rotation is stopped by the Stopper inside of the camera. For panning control, first unfasten two screws located on the bottom and rotate in the direction you want, and then fasten them to fix the camera.

In case of tilting, you can change the slope of your camera from zero to 90 degree. However if the slope angle is under 17 degree, you can encounter a partial image hide problem. To fix the location after adjusting the tilting angle, use the Tilt fixing screws.

To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever. When you install the camera on the inclined ceiling or wall, you can rotate the camera lens to see a correct direction image.

Panning

ENG

Tilting

Lens rotation

English – 13

How to use OSD Menu

USING ICONS IN THE MENU

• (EXIT)

Exits the menu setting.

Before you exits the menu setting, select SAVE to save your settings, or select QUIT to cancel.

• (RET)

Returns to the previous menu.

• (HOME)

Returns to the main menu.

• (SAVE)

Used to save your settings of MASK AREA, PRIVACY ZONE and more.

Once you save your settings, they will remain even if you select QUIT in the menu.

• (DEL)

Used to deletes your settings of MASK AREA, PRIVACY ZONE and more.

Once you delete your settings, they will not be restored even if you select QUIT in the menu.

MAIN MENU

ÃÃMAIN MENUÃÃ

PROFILE

CAMERA SET INTELLIGENCE PRIVACY ZONE OTHER SET SYSTEM INFO LANGUAGE

• PROFILE

You can set a mode according to the camera installation conditions.

• CAMERA SET

Configure Camera related functions and data.

• INTELLIGENCE

You can configure the settings of motion detection, tracking and more.

• PRIVACY ZONE

You can configure the privacy related settings.

• OTHER SET

You can configure for Factory Defaults, and more.

• SYSTEM INFO.

Displays the system information including the camera version and communication settings.

• LANGUAGE

Select a preferred one from the supported languages.

14 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

PROFILE

ePROFILEf

ÃSTANDARD

ITS

BACKLIGHT DAY/NIGHT GAMING CUSTOM

In the PROFILE menu, you can configure the following camera settings at once.						ENG
CAMERA SET Menu
Previous	Sub-menus	STANDARD	ITS	BACKLIGHT	DAY/NIGHT	GAMING
Menu
IRIS		ALC	ALC	ALC	ALC	ALC
	ALC	-	-	-	-	-
	LENS	DC	DC	DC	DC	DC
	LEVEL	0	0	0	0	0
	BACKLIGHT	OFF	OFF	BLC	OFF	OFF
MOTION		(F.FAST)---	(F.FAST)---	NORM	(F.FAST)---	SLOW
DNR		MID	MID	MID	MID	MID
SHUTTER		OFF	AUTO1/250	OFF	OFF	OFF
SENS-UP		AUTOx4	AUTOx2	AUTOx4	AUTOx4	AUTOx4
XDR		MID	MID	MID	MID	MID
DAY/		AUTO	AUTO	DAY	AUTO	DAY
NIGHT
	NIGHT	-	-	-	-	-
	BURST	OFF	ON	OFF	OFF	OFF

English – 15

How to use OSD Menu

CAMERA SET Menu
Previous	Sub-menus	STANDARD	ITS	BACKLIGHT	DAY/NIGHT	GAMING
Menu
WHITE		DAY	DAY/NIGHT	DAY	DAY/NIGHT	DAY
BAL
	DAY	-	-	-	-	-
	MODE	ATW2	ATW1	ATW1	ATW1	ATW1
	RED	0	0	0	0	0
	BLUE	0	0	0	0	0
	NIGHT	-	-	-	-	-
	BRIGHTNESS	User setting	MID	User setting	MID	User setting
		allowed		allowed		allowed
	MODE	OFF	ATW2	OFF	ATW2	OFF
	RED	User setting	0	User setting	0	User setting
		allowed		allowed		allowed
	BLUE	User setting	0	User setting	0	User setting
		allowed		allowed		allowed
DETAIL		2	2	2	2	2

ITS

It will be set automatically so you can easily check the traffic conditions.

BACKLIGHT

It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.

DAY/NIGHT

It will be set automatically so it optimizes to the day or night conditions, respectively.

GAMING

It will be set automatically to help you take a picture in a regular indoor lighting condition.

16 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

CAMERA SETUP

eCAMERA SETf

CAMERA ID			OFF
IRIS			ALC
MOTION	(F.FAST)---
DNR			MID
SHUTTER			OFF
SENS-UP		AUTO X4
FLICKERLESS			OFF
XDR			MID
	d
	c
DAY/NIGHT			AUTO
WHITE BAL
DIGITAL ZOOM			OFF
DETAIL		[2]
V-SYNC		(INT)---
AGC COLOR SUP			LOW
REVERSE			H/V
POSI/NEGA		+
PIP			OFF
	d

Setup the general functions of zoom camera module. Use the cdefswitch to select a menu item.

CAMERA ID

[OFF, ON]

CAMERA ID

ABCDEFGHIJKLMNOPQRSTUVWXYZ0 123456789 :?-+*()/

SPffeeSP LOCATION
CAMERA-1..................
...........................
			ENG

The CAMERA ID menu is used for you to assign a unique name to a camera. If you press the SETUP switch with the CAMERA ID menu selected, you will see the appropriate screen.

You can enter up to 54 alphanumeric or special characters for the CAMERA ID. Select LOCATION and press the SETUP switch to move the display position of the CAMERA ID.

c

DIS

OFF

IRIS

[ALC]

The IRIS menu is used if you want to adjust the intensity of radiation incoming to the camera.

•ALC (Automatic Light Control)

If you press the SETUP switch with an ALCbased sub menu selected, you will see the appropriate screen.

English – 17

How to use OSD Menu

	ALC
LEVEL	[00]----I----
BACKLIGHT	OFF

The LEVEL menu is used to adjust the overall brightness, where “+” will increase the brightness and “–” will decrease it.

If you set the BACKLIGHT option to BLC, you will see a menu where you can set the BLC area.

you can set the desired BLC zone by defining the size and location.

	ALC
LEVEL	[00]----I----
BACKLIGHT		BLC
AREA		USER
<SIZE>
<LOCATION>

displayed dark on the monitor affected by the backlight. To solve this problem, you can use the BLC(Back Light Compensation) function to improve the sharpness of the image in such a high contrast scene.

AGC

[OFF, VERY LOW, LOW, MID, HIGH, VERY HIGH, USER, FIX]

The AGC (Auto Gain Control) menu is used to set the AGC level of the camera. When the AGC is active, the camera automatically increases the sensitivity by amplifying the Video signal when the strength of the signal falls below the normal value.

If OFF or FIX mode is selected in the SENS-UP menu, you can specify the AGC level.

If you press the SETUP switch with a USER sub menu selected, you will see the appropriate screen.

AGC USER

LEVEL [16]

If you use an ordinary camera in a scene with an intensive backlight, the object will be

In USER mode, you can break down the level in 16 steps from VERY LOW to VERY HIGH to your preference.

18 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

AGC FIX

LEVEL [01]

Note :

–If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the MOTION menu will be deactivated.

DNR	[OFF,LOW,MID,HIGH, USER(1~16)]

If you press the SETUP switch with a FIX sub menu selected, you will see the appropriate screen.

As a fixed value of the AGC gain is used in FIX mode, you can select one of the 16 detailed levels from VERY LOW to VERY HIGH before fixing it.

Note :

–If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the AGC menu will be deactivated.

–If FLICKERLESS is set to ON, the AGC FIX mode will be disabled.

MOTION

[S.SLOW, SLOW, NORM, FAST, F.FAST]

The MOTION menu is used to adjust the strength of the AGC level for a control of the camera motion. This is available only if the SENS-UP menu is set to AUTO.

You can select one from S.SLOW, SLOW, NORM, FAST and F.FAST for the AGC level.

If you monitor a fast moving object in a low contrast scene, select F.FAST while select S.SLOW for a hardly moving object in the same lighting condition.

You can configure the DNR (Digital Noise

Reduction) related settings.

Reduces the noise on the screen.

This is especially useful for a severely distorted screen.

You can set the level if you set DNR to USER.

SHUTTER	ENG
[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250,
AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO
1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10K]
The SHUTTER menu is used to configure settings
of the fixed / auto high-speed electronic shutter.
You can select one of 7 options from 1/100(PAL:1/120)
to 1/10K for the fixed high speed electronic shutter,
which is mostly used for imaging a fast moving object.
The auto high speed electronic shutter operates
as the fixed high speed shutter in a high contrast
scene but automatically focuses the target if the
iris opens fully in a low contrast scene like in ELC
mode. When it gets brighter back, the mode will
switch to the fixed high speed electronic shutter
mode.
However, the auto high speed shutter operates
properly only in a camera featuring a DC or VIDEO
lens.

English – 19

How to use OSD Menu

Note :

–If the SENS-UP function is set to AUTO, only items of OFF and AUTO are available in the SHUTTER menu.

–If the SENS-UP mode is set to FIX, the SHUTTER menu will be deactivated.

–If the FLICKERLESS function is set to ON, the SHUTTER menu will be deactivated.

SENS-UP

[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO X8, AUTO X12, AUTO X16, AUTO X24, AUTO X32, AUTO X48, AUTO X64, AUTO X96, AUTO X128, AUTO X256, AUTO X512, FIX X2, FIX X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24, FIX X32, FIX X48, FIX X64, FIX X96, FIX X128, FIX X256, FIX X512]

Automatically detects the ambient level of darkness in the dark or low contrast scene to extend the accumulated time, keeping the image bright and sharp; It can be also used as FIX mode.

Note :

–If the SHUTTER menu is set to fixed electronic shutter mode, the SENS-UP menu will not be available.

–If FLICKERLESS is set to ON, the FIX mode of the SENSUP menu will be disabled.

–If the SHUTTER menu is set to AUTO, the SENS-UP menu can be set to either OFF or AUTO mode.

FLICKERLESS

[OFF, ON]

If set to ON, the shutter speed will be fixed to 1/100(PAL:1/120) second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting.

Note :

–If the SHUTTER menu is set to AUTO or FIX mode, the FLICKERLESS menu will not be available.

–If the SENS-UP function is set to FIX mode, the Flickerless menu will be deactivated.

–If AGC is set to FIX mode, the FLICKERLESS function will be disabled.

XDR (eXtended Dynamic Range) [OFF, LOW, MID, HIGH]

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

Select one from OFF, LOW, MID and HIGH. Closing to HIGH will increase the compensation level.

DAY/NIGHT

[DAY,NIGHT,AUTO]

• DAY

If set to DAY, it will be fixed to DAY mode regardless of the ambient conditions.

• NIGHT

If set to NIGHT, it will be fixed to Black-and-White mode regardless of the ambient conditions.

20 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

If you press the SETUP switch with a NIGHT sub menu selected, you will see a menu where you can set Burst to OFF/ON.

If BURST is set to ON, the Burst signal will output together with the black-and-white composite video signal. If BURST is set to OFF, the Burst signal does not output.

You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.

• AUTO

The camera will automatically switch between DAY and NIGHT mode, according to the lighting condition.

If you press the SETUP switch with an AUTObased sub menu selected, you will see the appropriate screen.

AUTO
BURST		OFF
DAYÆNIGHT
BRIGHTNESS		MID
DWELL TIME		2S
NIGHTÆDAY
BRIGHTNESS		MID
DWELL TIME		5S
MASK AREA		1 2

for which you can select from LOW, MID, and HIGH. As you adjust it from HIGH to LOW, the screen switches to black and white mode under the darker situation.

DWELL TIME of DAYÆNIGHT sets the time to maintain switched black and white mode.

	The BRIGHTNESS of NIGHTÆDAY sets the
	brightness degree of BW to color switching,
	for which you can select from LOW, MID, and
	HIGH. As you adjust it from HIGH to LOW, the
	screen switches to color mode under the darker
	situation.	ENG
	DWELL TIME of NIGHTÆDAY sets the time to
	maintain switched color mode.

The MASK AREA menu is used to prevent unintended mode switching or inability of determining the switching due to existence of high spot light source at night.

If you press the SETUP switch in item 1 or 2 of the MASK AREA menu, you will see a menu where you can specify an area to MASK.

MASK AREA

<SIZE> <LOCATION>

You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.

The BRIGHTNESS of DAYÆNIGHT sets the
brightness degree of color to BW switching,

English – 21

How to use OSD Menu

You can specify MASK 1 and 2 simultaneously. The MASK is only for determining the mode switching, and any excessive bright area at night will be excluded by the configured MASK.

Note :

–If BACKLIGHT is set to BLC, the MASK AREA function will be deactivated.

WHITE BAL

[DAY/NIGHT]

If you want to adjust the color scheme, use the

WHITE BALANCE function.

• DAY

In DAY mode, you can set the color values of RED and BLUE. The screen will be displayed in colors according to your settings.

	WHITE BAL
DAY/NIGHT				DAY
	MODE		AWC
	RED	[00]----I----
	BLUE	[00]----I----
	R-GAIN	[0248]
	B-GAIN	[0247]

Note :

–You can set the values of R-GAIN and B-GAIN only in AWC mode.

• NIGHT

Use the NIGHT mode if you want to set the white balance differently according to the ambient luminance.

If the NIGHT mode is set to OFF, the white balance will always operate as set in DAY mode; if not to OFF, the camera will switch to as set in DAY/NIGHT mode according to the brightness.

In NIGHT mode, you can set the values of RED, BLUE and BRIGHTNESS. The screen will be displayed in colors according to your settings.

WHITE BAL
DAY/NIGHT		NIGHT
BRIGHTNESS			MID
MODE		AWC
RED	[00]----I----
BLUE	[00]----I----
R-GAIN	[0248]
B-GAIN	[0247]

Note :

–You can set the values of R-GAIN and B-GAIN only in AWC mode.

–If AGC is set to OFF or FIX, you can not access the

NIGHT menu.

–For adjusting the white balance, the following 5 modes are provided:

22 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

•ATW1(Auto Tracing White Balance mode 1): The camera can automatically adjust the color temperature in real time, according to

the ambient conditions. The color temperature ranges from approx. 2500K to 9300K.

•ATW2: The color temperature ranges from approx. 2,000K to 10,000K.

•AWC ( Auto White Balance Control): If you press the SETUP switch in the appropriate item position, Auto White Balance will perform once.

•3200K : Set color temperature to 3200K

•5600K : Set color temperature to 5600K

–RED : Adjusts the strength of the red color.

–BLUE : Adjusts the strength of the blue color.

–R-GAIN/B-GAIN : Enables you to set the current color temperature manually.

–BRIGHTNESS : Select a brightness level in switching from setting in DAY mode to setting in

NIGHT mode.

DIGITAL ZOOM

[ON/OFF]

You can set the digital zoom factor and position. If you press the SETUP switch with the DIGITAL ZOOM function set to ON, you will see the appropriate screen.

When the zoom factor and position are defined, the digital zoom function will operate.

DIGITAL ZOOM

RATIO	[X1.0]
< LOCATION >

	- LOCATION : If you press the SETUP switch in the
	condition where the image is enlarged as much as the	ENG
	ratio setting, you can watch an invisible area of the
	effective screen as well using the cdefswitch.

Note :

–If the digital zoom factor is set to larger than 1x, the FENCE function will be deactivated.

The DIGITAL ZOOM function enlarges the pixel itself, which can cause deterioration of the quality.

DETAIL [0~3]

Controls the horizontal or vertical distinction.

V-SYNC

[INT, LINE]

Select the vertical sync mode for INT or LINE.

If you select INT, the camera will use the internal synchronization.

If selecting LINE, the camera will use the external power source frequency for the synchronization.

You can adjust the LL-PHASE.

English – 23

How to use OSD Menu

Note :

–Use of DC 12V will fix V-SYNC to INT, which can not be changed.

AGC COLOR SUP

[LOW , MID, HIGH]

Adjust the color scheme according to the AGC value.

REVERSE

[OFF, H, V, H/V]

Mirrors video signals horizontally, vertically, or both.

POSI/NEGA

[+, -]

Output as it is or mirror the video brightness signal.

PIP

[OFF, ON]

Displays a sub image together with the main image on the same screen using the Picture In Picture function.

Note :

–If more than one privacy zone is set and the PRIVACY SET is set to ON, the PIP function will be deactivated.

–If the INTELLIGENCE function is set to FENCE mode, the PIP menu will be deactivated.

DIS

[OFF, ON]

Digital Image Stabilization will set the anti-shake compensation.

Note :

–If you set DIS to ON, the compensation area will be enlarged as set in the digital zoom factor.

If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS function will be deactivated.

INTELLIGENCE

eINTELLIGENCEf

MOTION			OFF
ADVANCED			OFF
MASK AREA	1 2 3 4
DISPLAY				ON
SENSITIVITY	[4]
RESOLUTION	[5]

You can set the motion detection and tracking in the

INTELLIGENCE menu.

MOTION

[OFF,TRACKING,DETECTION]

•TRACKING

Detects and tracks a moving object.

•DETECTION

Detects a moving object.

Note :

–If it is set to DETECTION, you can not set such functions as

FIXED/MOVED and FENCE in the ADVANCED menu.

24 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

ADVANCED

[OFF, FIXED/MOVED, FENCE]

Detects a motion of an object and displays an image of any moving object before tracking the moving route.

• FENCE

This is to detect if a moving object passes through the specified LINE or AREA.

In a condition where a moving object is detected in an analysis of the previous and current frames whose movement overlaps a certain area, the system displays “PASS” if the object’s center line passes through the line while it displays “ENTER” or “EXIT” if the center point passes through the area.

	FENCE
LINE		OFF
AREA		OFF

You can set the position and detection direction of the LINE, and the size and position of the AREA.

- How to set the line

LINE
PIXEL LEVEL	[4]
<POINT>
DIRECTION	§¨

If you press the SETUP switch with the LINE	ENG
option set to ON, you can specify the position
and detection direction of the line.

If you change the PIXEL LEVEL for setting

the position, specify the pixel that moves by a single pressure of the cdefswitch.

In <POINT>, you can specify the first position of the line by pressing the SETUP switch once, and

the second position by pressing the switch again. Use the cdefswitch to specify the position.

Set each position of the two points and press the SETUP switch to complete the positioning.

If you change the DIRECTION, you can specify the detection direction. The detection direction based on the defined two points will be displayed on the screen.

English – 25

How to use OSD Menu

- How to set the area

	AREA
PIXEL LEVEL			[4]
<SIZE>
<LOCATION>

If you press the SETUP switch with the AREA option set to ON, you can specify the position and size of the area.

If you change the PIXEL LEVEL for setting

the position, specify the pixel that moves by a single pressure of the cdefswitch.

In <SIZE>, press the SETUP switch and use the cdefswitch to adjust the size. Press the SETUP switch again to complete the sizing.

In <LOCATION>, press the SETUP switch and use the cdefswitch to specify the position. Press the SETUP switch again to complete the positioning.

Note :

–If you set the LINE of the FENCE to ON, PRIVACY 12 will not be available.

Functions of FENCE, PIP, DIS and DIGITAL ZOOM (if the digital zoom factor is set to larger than 1x) can not be

used simultaneously.

–In the boundary of the defined AREA and LINE, a FENCE detection error may occur if two or more moving objects overlap with each other or one object separates in multiple directions.

•FIXED/MOVED

If an object on the screen suddenly disappears or an object comes out of nowhere and stays for a certain time, the area will be displayed.

A detection (FIXED/MOVED) error may occur if :

- multiple motions occur continuously in random directions

- a fixed object moves in one position continuously - a second object screens the first moving object

MASK AREA [1~4]

Specify a detection exception area to mask.

Select a mask number and specify the size and position.

MASK AREA

<SIZE> <LOCATION>

26 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

DISPLAY

[ON, OFF]

With the DISPLAY option set to ON, a motion or a set ADVANCED function will be displayed on the screen, if detected.

If you set the PRIVACY SET to ON, your PRIVACY ZONE settings will be applied.

You can change the style to adjust the mosaic size and color of the PRIVACY ZONE.

SENSITIVITY

[1~7]

Set the sensitivity of the motion detection.

RESOLUTION

[1~5]

If setting it to high, the camera can detect even a trivial movement of the target.

PRIVACY ZONE SETUP

	ePRIVACY ZONEf
1	2	3	4	5	6
7	8	9	10	11	12
PRIVACY SET					ON
STYLE				MOSAIC1

The PRIVACY function will protect your privacy by screening the privacy area that you have specified during monitoring. You can specify up to 12 privacy zones.

ePRIVACY ZONEf

1	2	3	4	5	6
7	8	9	10	11	12

PRIVACY SET	ON
STYLE	COLOR
Y-LEVEL	[128]
RED	[128]
BLUE	[128]	ENG

Use the cdefswitch to select one from

PRIVACY 1 through 12.

Select one from PRIVACY 1~12 and press the SETUP switch to confirm your setting. You can specify a pixel that moves as you change the PIXEL LEVEL to set the position.

PRIVACY ZONE SET1

PIXEL LEVEL			[4]
<POINT>
<POSITION>

English – 27

How to use OSD Menu

- How to set the point

You can set each position of the 4 points.

If you press the SETUP switch in <POINT>, you will see the points available in the PRIVACY ZONE. Each time you press the SETUP switch, the points available will move.

Use the cdefswitch to set the position of each point. Set each position of the four points and press the SETUP switch to complete the positioning.

-How to set the position

You can move the position of the overall area.

By pressing the SETUP switch in <POSITION>, you can move the overall position of the privacy zone.

Use the cdefswitch to move the position and press the SETUP switch to confirm it.

Note :

–If more than one PRIVACY ZONE is specified and the PRIVACY SET is set to ON, the PIP function will be deactivated.

–If the 12th PRIVACY ZONE is specified, the LINE function of FENCE will be deactivated.

OTHER SET

eOTHER SETf
FACTORY DEFAULTS
OSD COLOR	BW

FACTORY DEFAULTS

All the settings will be restored to the factory default.

OSD COLOR

[BW, R/G/B]

You can set the OSD(On-screen Display) color to COLOR or B/W.

28 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu

SYSTEM INFORMATION

Initial Configuration Table

eSYSTEM INFOf

TYPE	3_VAR_NOR_N
SERIAL NO. 000000000000000
CAMERA VER.	0.50_090101

You can check the system information such as SERIAL NO and CAMERA VER.

LANGUAGE

eLANGUAGEf

ÃENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

The camera supports 5 different languages.

Select a preferred language.

	• Camera Configuration
	CAMERA ID	OFF
	IRIS	ALC
	AGC	VERY HIGH
	MOTION	(F.FAST)
	DNR	MID
	SHUTTER	OFF	ENG
	SENS-UP	AUTO x4
	FLICKERLESS	(OFF)
	XDR	MID
	DAY/NIGHT	AUTO
	DIGITAL ZOOM	OFF
	DETAIL	[2]
	AGC COLOR SUP	MID
	REVERSE	H/V
	POSI/NEGA	+
	PIP	OFF
	DIS	OFF
	V-SYNC	INT

English – 29

Specifications

SPECIFICATIONS

Items

Sub-items

SCC-B5366N/SCC-B5366SN/SCC-B5368N/SCC-B5368SN

Camera Type

CCTV Camera

Device

1/3” Super-HAD IT CCD

Image

Pixels

Total

811 x 508

Effective

768 x 494

System

Interlace

Scanning Line

525 lines

Frame

30frame/1sec

Scanning

Horizontal

Internal Mode

15,734 Hz

Frequency

Line-lock Mode

15,750 Hz

Vertical

Internal Mode

59.94 Hz

Frequency

Line-lock Mode

60 Hz

Condition

Min. Scene illumination

Sens-up

F No.

Level

DAY

NIGHT

OFF

1.2

50

IRE

0.4

Lux

0.4

Lux

Min. Scene

OFF

1.2

30

IRE

0.24

Lux

0.24

Lux

Illumination

OFF

1.2

15

IRE

0.12

Lux

0.12

Lux

512 times

1.2

50

IRE

0.0008

Lux

0.0008

Lux

512 times

1.2

30

IRE

0.00047

Lux

0.00047

Lux

512 times

1.2

15

IRE

0.00023

Lux

0.00023

Lux

Number of Privacy Zone

12 (Polygonal Method)

Day/Night

DAY/NIGHT/AUTO

Motion Detection

OFF/Tracking/Detection

eXtended Dynamic Range(XDR)

Off/On (Level Setting)

Functions

D-Zoom

x1 ~ x16 (x0.1 STEP)

PIP

Off/On

High Speed Shutter

1/60 ~ 1/10Ksec (OSD)

Flickerless

Off/On

Sens-Up

x2 ~ x512

BLC

Off/On (Area Setting)

30 – DIGITAL COLOR DOME CAMERA