®
ELECTRICTRIMMER/EDGER
OWNER’SMANUAL
MODELS:RM112ST andRM114ST
IMPORTANT: Read and understand this manual before assembling or operating this tool. Improper use of this tool can cause severe injury or death.Keepthismanualforfuturereference.
DoubleInsulated
PART NO. 769-05212 P00 |
(07/09) |
REMINGTON® ELECTRICTRIMMER/EDGER | iII
tableofcontents |
|
|
1 |
ImportantSafetyInformation |
1 |
2 |
ProductIdentification |
3 |
3 |
Trimmer/EdgerAssembly |
4 |
|
AssemblingTrimmer/Edger. . . . . . . . . . . . . . . . . . . . . . . . |
4 |
4 |
Trimmer/EdgerOperation |
6 |
|
ExtensionCords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
6 |
|
OperatingtheTrimmer/Edger. . . . . . . . . . . . . . . . . . . . . . . |
7 |
5 |
Trimmer/EdgerMaintenance |
13 |
6 |
Troubleshooting |
14 |
|
ReplacementSpool . . . . . . . . . . . . . . . . . . . . . . . . . . . |
14 |
7 |
WarrantyInformation |
15 |
iv |
welcome
ThankyouforpurchasingthisRemington®ElectricTrimmer/Edger.Weareproudtoo er this quality product to assist you in keeping your property neat and well-groomed.
This owner’s manual provides complete instructions for safely assembling, operating, and maintaining yourTrimmer/Edger.Read and save these instructions.Refer to this manual each time before using your Trimmer/Edger.
SAVE THESE INSTRUCTIONS
SERVICE INFORMATION
DO NOT RETURN THIS PRODUCT
Please call the Customer Support Department or visit our website for assistance:
U.S. |
or |
Canada |
|
1-866-206-2707 |
1-877-696-5533 |
||
|
www.remingtonpowertools.com
DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.
THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.
For assistance regarding the assembly, controls, operation or maintenance of the unit, please call the Customer Support Department. Additional information about the unit can be found on our website.
For service, please call the Customer Support Department to obtain a list of authorized service dealers near you. Service on this unit, both within and after the warranty period, should only be performed by an authorized and approved service dealer. When servicing, use only identical replacement parts.
Before beginning, locate the unit’s model plate, which lists the model and serial numbers of your unit. Refer to the sample plate below and copy the information for future reference.
Copy the model and parent part numbers here:
Copy the serial number here:
All information, illustrations and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.
Copyright© 2009 MTD SOUTHWEST INC, All Rights Reserved.
REMINGTON® ELECTRICTRIMMER/EDGER | 1
1importantsafetyinformation
SAFETY
WARNINGS
WARNING:Whenusingelectric gardeningappliances,basicsafety precautionsshouldalwaysbefollowed to reduce the risk of fire, electricshock,andpersonalinjury, includingthefollowing:
READ ALL INSTRUCTIONS BEFORE OPERATINGTRIMMER/EDGER.
WARNING: This product contains chemicals known to the State of California to cause cancer or birth defects, or other reproductiveharm.
BEFORE OPERATING
TRIMMER/EDGER
1.Avoid Dangerous Environments
•Do not operate trimmer/edger in rain or in damp or wet locations.
•Do not operate trimmer/edger while under the influence of alcohol,medications,or drugs.
•Do not operate trimmer/edger when you are tired.
•Donotoperatetrimmer/edgerifit isdamagedornotsecurelyandfully assembled.
2.Keepchildrenaway.Keepallbystanders a safe distance from work area.
3.Donotusetrimmer/edgerforanyjob except that for which it is intended.
4.Only well instructed adults should operate trimmer/edger. Never allow children to operate trimmer/edger.
5.Dressproperlywhenoperatingtrimmer/edger.
•Do not wear loose clothing or jewelrythatcangetcaughtinthemoving parts of the trimmer/edger.
•Always wear rubber gloves and substantial foot wear when working outside.
•Always wear protective hair covering to contain long hair.
•Always wear a face or dust mask if operation is dusty.
6.Always wear eye protection that meets or exceeds the requirements of ANSI Z87.1.
7.Wear long pants and shoes when operating this tool.
WARNING:To reduce the risk of electric shock, use only with an extension cord intended for outdooruse,suchasSW-A,SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A,orSJTOW-A.
8.Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your trimmer/edger will draw. An undersized extension cord will cause adropinlinevoltageresultinginloss of power and overheating.
The table below shows the correct size extension cord to use depending on cord length and nameplate ampere rating. If in doubt, use the next larger gauge cord. The smaller thegaugenumber,thelargerthecord. To reduce the risk of disconnection of trimmer/edger from the extension cord during operation, use the cord hitch described in this manual.
CordLength |
AWGCordSize |
25 feet |
18 AWG |
50 feet |
16 AWG |
100 feet |
16 AWG |
150 feet |
14 AWG |
9.To reduce the risk of electric shock, the trimmer/edger has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The trimmer/edger’s plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extensioncord,reversetheplug.Ifthe plugstilldoesnotfit,obtainacorrect polarizedextensioncord.Apolarized extension cord will require the use of a polarized wall outlet.This plug will fit into the polarized wall outlet only one way.If the plug does not fit fully into the wall outlet,reverse the plug. If the plug still does not fit, contact a qualified electrician to install the properwalloutlet.Donotchangethe trimmer/edger plug, extension cord receptacle, or extension cord plug in any way.
2| Chapter 1: Important Safety Information
10.Provide Ground Fault Circuit Interrupter (GFCI) protection on the circuit or outlet to be used for trimmer/edger. You may use receptacles with built-in GFCI protection for this safety measure.
WHILE OPERATING
TRIMMER/EDGER
1.Stayalert.Watchwhatyouaredoing. Use common sense.
2.Beawareofextensioncordwhileoperatingtrimmer/edger.Becarefulnottotrip over extension cord.
3.Avoid unintentional starting. Do not carry plugged-in trimmer/edger with finger on switch.Be sure switch is OFF when plugging in trimmer/ edger.
4.Do not overreach.Keep proper footing and balance at all times when operating trimmer/edger.
5.Disconnect the trimmer/edger from the power supply
•when not in use
•before servicing
6.Donotforcetrimmer/edger.Itwilldo thejobbetterandwithlesslikelihood ofariskofinjuryattherateforwhich it was designed.
7.Do not abuse power cord.Never pull orcarrytrimmer/edgerbypowercord. Never yank cord to disconnect from receptacle. Keep power cord from heat,oil,and sharp edges.
8.Keep hands and feet away from cutting area.
MAINTENANCE AND STORAGE OFTRIMMER/ EDGER
1.Maintain trimmer/edger with care.
•Inspect trimmer/edger cord periodically, and if damaged, have it repaired by a qualified service facility.
•Inspectextensioncordsperiodically and replace if damaged.
•If trimmer/edger is not working properly, has been dropped, damaged,leftoutdoors,ordroppedinto water,haveitrepairedbyaqualified service center.
•Keep handles dry, clean, and free from oil and grease.
•Keep guards in place and in working order.
2.Check damaged parts.
•Ifapartisdamaged,carefullycheck the damaged part before using the trimmer/edger.Make sure the part will operate properly and perform its intended function.
•Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and anyotherconditionthatmaya ect its operation.
•A guard or other part that is damaged should be properly repaired or replacedbyaqualifiedservicecenter unless indicated elsewhere in this manual.
•Use only geniune Remington® replacement parts and accessories. These are available from your local dealer. Use of any non-Reming- ton®partsoraccessoriescouldlead to injury to the user,damage to the unit,and void you warranty.
3.Servicing of Double-Insulated Tools:
•In a double-insulated tool, two systems of insulation are provided instead of grounding. No groundingmeansisprovidedonadoubleinsulated tool,nor should a means forgroundingbeaddedtothetool. Servicing a double-insulated tool requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated tool must be identical to the parts they replace.
4.Store idle trimmer/edger indoors. Whennotinuse,storetrimmer/edger and extension cord indoors in a dry location. Store trimmer/edger above the reach of children or in a locked area out of the reach of children.
Thismanualisyourguidetosafeandproper operation of the trimmer/edger.
SAVETHESE
INSTRUCTIONS.
REMINGTON® ELECTRICTRIMMER/EDGER | 3
2productidentification
A.MotorHousing
B.SpoolHousing
C.CuttingGuard
D.EdgingWheel
E.AdjustableFrontHandle
F.RearHandle
G.InletPlug orPowerCord
H.ExtensionCordRetainer
I.TriggerSwitch
J.TriggerSwitchSafetyButton
K.ShaftRotationButton
L.TelescopingShaft
M.TelescopeReleaseButton
A
D
J
F
K 
G E I H
M
L
C
B
Figure2-1:Remington®electrictrimmer/edger(modelRM112STshown)
Specifications
|
RM112ST |
RM114ST |
Input |
120V, 3.8A |
120V, 4.5A |
No Load Speed |
10000 rpm |
10000 rpm |
CuttingWidth |
12 inches (30cm) |
14 inches (35cm) |
NetWeight |
6.35 lbs. (2.88 Kg) |
6.35 lbs. (2.88 Kg) |
Line Diameter |
0.065 inch |
0.065 inch |
4|
3trimmer/edgerassembly
AssemblingTrimmer/Edger
WARNING: Do not operate trimmer/edger without guard or handleinplace.
AttachingCuttingGuard andEdgingWheel
1.Removethreemountingscrewstaped to underside of cutting guard.
2.Align key tabs on inside of cutting guard hole with cutouts on motor
housing and slide cutting guard over Figure3-2:Rotatingcuttingguardintoplace cutting head (see Figure 3-1). Slip
cutting guard past the tabs.
3.Rotate guard 90° until it stops (see Figure 3-2).
4. |
Insertonemountingscrewintocenter |
Figure3-4:Placingedgingwheeloverscrewholes |
|
screwholeattopofcuttingguard(see |
|
|
Figure 3-3).Tighten screw firmly. |
|
5. |
Place edging wheel over remaining |
|
|
two screw holes at top of cutting |
|
|
guard(seeFigure3-4).Attachedging |
|
|
wheel using two mounting screws. |
|
Figure3-3:Attachingmountingscrew
Figure3-5:Attachingedgingwheel
Figure3-1:Placingcuttingguardovercuttinghead
REMINGTON® ELECTRICTRIMMER/EDGER | 5
AttachingAdjustableFrontHandle
1.Removetheknobandboltfromfront handle (see Figure 3-6).
2.Place the handle on the trimmer/ edger shaft between the rear handle andthetelescopereleasebutton.Snap handle onto shaft (see Figure 3-7).
3.Insertboltbackintothefronthandle (see Figure 3-8).
4.Loosely screw knob onto bolt (see Figure 3-9).
5.Adjust handle to the most comfortable position and tighten the knob firmly.Do not overtighten the knob.
Figure3-6:Removingknobandboltfromhandle
Figure3-8:Insertingboltintohandle
Figure3-7:Placinghandleontoshaft
Figure3-9:Screwingknobontobolt
6|
4trimmer/edgeroperation
WARNING: Read and understandthisowner’smanualbefore operating trimmer/edger. Make certain you read and understand allSafetyWarningsonpages1and 2ofthismanual.Improperuseof this trimmer/edger can result in severe injury or death from fire, electric shock, or body contact withmovingparts.
ExtensionCords
Use proper extension cord with this tool. Use only a polarized (i.e., one blade is wider than the other), UL listed extension cord marked for outdoor use. The cord must be marked with suffix W or W-Afollowingthecordtypedesignation. Example: SJTW-A or SJTW.
Usepropersizedcordwiththistool.Cord must be heavy enough to carry current needed.Anundersizedcordwillcausevoltage drop at trimmer/edger.The trimmer/ edgerwilllosepowerandoverheat.Follow cord size requirements listed below.
CordLength |
AWGCordSize |
25 feet |
18 AWG |
50 feet |
16 AWG |
100 feet |
16 AWG |
150 feet |
14 AWG |
Inspect cord often.Replace if damaged.
ConnectingExtensionCord
WARNING: Fully seat the extension cord on the inlet plug or power cord of tool. Failure to do so could lead to overheating of trimmer/edger.Thiscouldcausea firethatresultsinpersonalinjury toyouorothers.
Thetrimmer/edgerhasabuilt-inextension cord retainer.This cord hitch prevents accidental disconnection of the power cord during use.The cord hitch is molded into the rear handle.
1a. Model RM114ST: Plug power cord into extension cord (see Figure 4-1).
1b. Model RM112ST: Plug extension cord into inlet plug of tool (see Figure 4-2).
2.Create a loop in the extension cord and insert through the bottom of the tool housing (see Figure 4-3).
3.Pullthelooptightaroundthemolded cord hitch (see Figure 4-4).
Note: For Model RM114ST, an optional method of retaining the extension cord is shown in Figure 4-5. Use this method with larger-gauge cords that may not fit into the extension cord retainer.
Figure4-1:Pluggingextensioncordintopowercord,
ModelRM114ST
Figure4-2:Pluggingextensioncordintoinletplug,
ModelRM112ST
Figure4-3:Insertingextensioncordloopthroughbottom ofhandle
Figure4-4:Pullextensioncordlooptightaroundmolded cordhitch
Figure4-5:Optionalmethodofretainingextensioncord
REMINGTON® ELECTRICTRIMMER/EDGER | 7
Operatingthe
Trimmer/Edger
WARNING:Thetrimmer/edger canthrowdebris,causinginjuryto thosenearby.
•Wearapprovedeyeprotection, long pants, and shoes while operatingthistool.
•Keep bystanders away from workarea.
WARNING: Keep away from cuttinglineandcuttingheadwhile trimmer/edgerisrunning.Contact withcuttinglinecancauseserious injury.
•Keep cutting head away from your hands and feet and bystanderswheninuse.
•Keepcuttingguardinplaceand inproperworkingorder.
•Wearlongpantsandshoeswhile operatingthistrimmer/edger.
•Stop trimmer/edger and unplugpowercordbeforeservicingorexaminingpowerhead.
AdjustingShaftLength
You can adjust the shaft length of this trimmer/edger for your comfort and convenience.
1.Slidetelescopereleasebuttonupward toward handle (see Figure 4-6).
2.Adjust shaft to desired length and release button (see Figure 4-7).
Note:The inside shaft has notches in it.Adjust shaft length to one of these presetpositions.Youwillheara“click” when engaged into a notch properly.
Figure4-6:Slidingtelescopingreleasebuttonupward
Figure4-7:Adjustingshaftlength
StartingtheTrimmer/Edger
1.Holdtrimmer/edgerusingbothfront and rear handles. Keep your thumb and fingers o the button and switch on the rear handle (see Figure 4-8).
2.When ready to start the trimmer/ edger, press in the trigger switch safety button with your thumb (see Figure 4-9).
3.Squeeze the trigger switch with your fingers (see Figure 4-10). The trimmer/edger will start.
4.Tostopthetrimmer/edger,releasethe trigger switch.
Figure4-8:Holdingtrimmer/edgerrearhandle
TriggerSwitch
SafetyButton
Figure4-9:Pressingtriggerswitchsafetybutton
Figure4-10:Squeezingtriggerswitch
8| Chapter 4:Trimmer/Edger Operation
Trimming
Toreduceexcessivelinewearandimprove trimming performance, follow the steps below to trim grass and weeds.
1.Removeanystring,wire,orothermaterials that could become entangled in the trimmer/edger from the trimming area.
2.Holdtrimmer/edgerusingbothfront and rear handles (see Figure 4-11).
3.Slowlysweepthetrimmer/edgerfrom side to side or front to back.
4.Do not force the trimmer/edger.Allowonlythetipofthetrimmer/edger line to cut the grass or weeds.
5.If grass or weeds are tall,cut them in several increments,starting from the top and working to the bottom.
AdvancingTrimmerLine |
ReplacingTrimmer/EdgerLine |
WARNING: Blade is sharp. To prevent serious injury, do not touchblade.
Toadvancenewtrimmer/edgerline,tapthe lineadvancebuttononthegroundwhilethe trimmer/edgerisrunning(seeFigure4-12). Thebladeattachedtothecuttingguardwill cut the line to the proper length.
Follow the precautions below to ensure top line performance.
•Do not hold the line advance button on the ground. This will allow trimmer/edger line to constantly feed o the spool.
•Tap the line advance button only once to advance line.If more line is needed, wait a few seconds and tap again.
•Be sure to advance the line as it wears down.If you wait too long to advance new line, the existing line will wear down too short and can retract into the spool. If this happens, remove the spool and reroute the line out of the spool. Reinstall the spool to the trimmer/edger head.
Line
Advance
Button
Figure4-12:Advancingtrimmer/edgerline
WARNING:Topreventserious personalinjury,neverusemetalreinforcedline,wire,orrope,etc. These can break o and become adangerousprojectile.
CAUTION: Use of line other than specified could cause personalinjuryorproductfailure.
Forreplacementline,useanylonmonofilament line of 0.065 inch in diameter.You canpurchasereplacementlineatmostlawn and garden stores.
RemovingtheSpool
1.Press in the two locking tabs holding the spool cover to the spool housing (see Figure 4-13).
2.Remove the spool cover and spool from spool housing (see Figure 4-14).Note: If spool spring comes o of spool housing, replace spring by placing the smaller end of spring into centerofspoolhousing.Note:Ifinstalling replacement spool and line (P/N 731-07488),skip to step 13,page 10.
3.Cleangrassandotherdebrisfromthe spoolandspoolhousingusingabrush (see Figure 4-15).
Figure4-11:Holdingtrimmer/edger
Figure4-13:Unlockingspoolcover
REMINGTON® ELECTRICTRIMMER/EDGER | 9
4. Remove the line retaining ring from the spool (see Figure 4-16).
5. Measure out 30 feet of replacement line.
6. Pushoneendofthenewlinethrough the left line mounting hole on the spool (see Figure 4-17).
7. Feed 15 feet of the line through this hole. Feed the other 15 feet of line throughtherightlinemountinghole (see Figure 4-18). Pull the line tight (see Figure 4-19).
LineRetaining
Ring
Figure4-14:Removingspoolcoverandspool
Figure4-16:Removinglineretainingring
Directionof
LineFeed
Figure4-15:Cleaningspool
Figure4-17:Insertinglineinlefthole
Figure4-18:Insertinglineinrighthole
Directionof
LineFeed
Figure4-19:Pullinglinetight
Directionof
LineFeed
10 | Chapter 4:Trimmer/Edger Operation
8.Lay the line from the left mounting holeintotheupperspoolsection.Lay thelinefromtherightmountinghole across the other line. Insert this line into the retaining slot between the upper and lower spool section, then lay the line into the lower spool section. See Figure 4-20 for proper line placement.
9.Place the line from the upper spool sectionthroughthelineretainingring (see Figure 4-21).
10.Place the line retaining ring back on the spool (see Figure 4-22).
11.Position each line section in the slots on either side of the retaining ring (see Figure 4-23).
12.Hold the retaining ring in place and make sure the line remains in the retaining ring slots. Rotate the spool while holding the retaining ring in place. The line will roll onto the spool (see Figure 4-24). IMPORTANT:Makesuretorotatethe spool so the line winds onto spool in the direction indicated on the spool top. Wind line until four inches of line remains outside the spool.
13.Replace spool onto spool spring and press spool down.Lay exposed trimmer/edger line into slots on spool housing (see Figure 4-25).
14.Align tabs on spool cover with slots inspoolhousing.Replacespoolcover onto spool housing and snap into place (see Figure 4-26).
Retaining
Slot
Figure4-20:Arranginglineintospool
Figure4-22:Placingretainingringontospool
Figure4-21:Placingupperspoollineintoretainingring
LinesThrough
Slotsin
RetainingRing
Figure4-23:Positioninglineinretainingringslots
REMINGTON® ELECTRICTRIMMER/EDGER | 11
Figure4-26:Replacingspoolcoverontospoolhousing
Figure4-25:Replacingspoolintospoolhousing
Figure4-24:Windinglineontospool
12 | Chapter 4:Trimmer/Edger Operation
ConvertingtoEdger
This tool easily converts to an trimmer/ edger.Follow the steps below.
1.Slidetelescopereleasebuttonupward toward handle (see Figure 4-27).
2.Adjust shaft to desired length and release button (see Figure 4-28). Note: Make sure inner shaft locks into one of the preset notches before operating.
3.Press the shaft rotation button lo-
cated on the rear handle (see Figure |
Figure4-29:Pressingshaftrotationreleasebutton |
4-29). |
|
4.Holding the rear handle in place, grasp the front handle and rotate the shaft and power head 180° to the edging position (see Figure 4-30).
5.Release the shaft rotation button.
6.Loosenknobonfronthandle.Rotate handle 180° and tighten knob.
UsingEdger
1.Make sure trimmer/edger line is advanced to full cutting length.
2.Roll the trimmer/edger using the edging wheel attached to the cutting guard (see Figure 4-31).
3.Start the trimmer/edger and trim along edging lines. Be sure to keep the cutting lines vertical.
Figure4-27:Slidingtelescopingreleasebuttonupward |
Figure4-30:Rotatingshaftandpowerhead |
Figure4-31:Edging
Figure4-28:Adjustingshaftlength
REMINGTON® ELECTRICTRIMMER/EDGER | 13
5trimmer/edgermaintenance
Cleaningand
Maintenance
WARNING: Disconnect trimmer/edgerfrompowersupplybefore cleaning or servicing. Severe injury or death could occur from fire, electrical shock, or rotating string.
WARNING: When cleaning trimmer/edger:
•Do not submerse in any liquids
•Do not use products that con-
tain Ammonia, Chlorine, or
abrasives
• Donotusechlorinatedcleaning Figure5-1:Cleaningtrimmer/edgerhousing solvents,CarbonTetrachloride,
Kerosene,orGasoline.
Useasoftclothdampenedwithamildsoap andwatermixturetowipetrimmer/edger housing.Donotsprayorpourwaterdirectly onto trimmer/edger.
Useasti bristledbrushtocleanairintake openings on housing (see Figure 5-1).
Whennotinuse,storethetrimmer/edger and extension cord indoors in a dry location.
This tool has no user serviceable parts.
14 |
6troubleshooting
WARNING: Unplug trimmer/edger from power source before servicing.
Severeinjuryordeathcouldoccurfromfire,electricalshock,orrotatingline.
Note: For additional help, visit
www.remingtonpowertools.com.
OBSERVEDFAULT |
POSSIBLECAUSE |
REMEDY |
||
|
|
|
|
|
Motordoesnotrunwhenyouturntrig- |
1. |
Extension cord connection is loose |
1. |
Check cord connection at electri- |
ger switch on |
|
|
|
cal outlet and at rear of trimmer/ |
|
|
|
|
edger |
|
|
|
|
|
Line does not feed when you tap the |
1. |
All line has been used on spool |
1. |
Installnewlineonspool,following |
line advance button |
|
|
|
steps under Replacing Trimmer/ |
|
|
|
|
EdgerLine, page 8 |
|
2. |
Line has retracted into spool |
2. |
Remove spool and pull line out, |
|
|
|
|
then replace spool |
3.Line is caught or tangled on spool and will not feed
3.Remove spool, loosen and untangle line, then replace spool
ReplacementSpool
PartNumber |
Description |
731-07488 Replacement Spool
with Line
WARNING: Use of non-Rem- ington® parts or accessories may cause personal injury or damage totheunit.
REMINGTON® ELECTRICTRIMMER/EDGER | 15
7warrantyinformation
MANUFACTURER’S LIMITED WARRANTY FOR:
The limited warranty set forth below is given by Remington LLC (“Remington”) with respect with new merchandise purchased and used in the United States, its possessions and territories.
Remington warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment not approved by Remington for use with the product(s) covered by this manual will void your warranty as to any resulting damage.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE THROUGH YOUR LOCAL AUTHORIZED SERVICE DEALER. To locate the dealer in your area, please check for a listing in the Yellow Pages or contact the Customer Service Department of Remington by calling 1-866- 206-2707 or writing to P.O. Box 361032, Cleveland, OH 44136 or if in Canada call 1-877-696-5533. No product returned directly to the factory will be accepted unless prior written permission has been extended by the Customer Service Department of Remington.
This limited warranty does not provide coverage in the following cases:
A.Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars
B.Remington does not extend any warranty for products sold or exported outside of the United States of America, its possessions and territories, except those sold through Remington’s authorized channels of export distribution
Remington reserves the right to change or improve the design of any Remington Product without assuming any obligation to modify any product previously manufactured.
No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product shall
bind Remington. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. Remington shall not be liable for incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn care
services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the use or misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the person for whom it was purchased as a gift.
How State Law Relates to this Warranty: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To locate your nearest service dealer dial 1-866-206-2707 in the United States or 1-877-696-5533 in Canada.
REMINGTON LLC
P.O. Box 361032
Cleveland, OH 44136
Loading...