Packard Bell
EasyNote V / MV
Disassembly Manual
2
Table of Contents |
|
Overview .................................................................................................................. |
3 |
Disassembly Instructions.......................................................................................... |
3 |
Reassembly Instructions .......................................................................................... |
3 |
Required Tools ......................................................................................................... |
3 |
Hazardous Voltage ................................................................................................... |
4 |
Avoid Electrostatic Discharge................................................................................... |
4 |
Power Supply Unit .................................................................................................... |
4 |
Base Assembly ............................................................................................................ |
5 |
Battery ...................................................................................................................... |
5 |
Hard Disk Drive ........................................................................................................ |
5 |
Optical Disc Drive ..................................................................................................... |
6 |
Memory Modules ...................................................................................................... |
7 |
Bluetooth Module (Optional)..................................................................................... |
8 |
CPU.......................................................................................................................... |
9 |
Wireless LAN Card ................................................................................................. |
10 |
TV Card (optional) .................................................................................................. |
11 |
Keyboard ................................................................................................................ |
11 |
Speakers ................................................................................................................ |
12 |
Mainboard .............................................................................................................. |
13 |
Modem ................................................................................................................... |
17 |
Subwoofer .............................................................................................................. |
17 |
USB/TV-Out/DC-Board........................................................................................... |
18 |
TV Aerial Connector (Optional) .............................................................................. |
18 |
Touchpad ............................................................................................................... |
18 |
LCD Assembly ........................................................................................................... |
19 |
LCD Panel .............................................................................................................. |
20 |
Inverter Board......................................................................................................... |
20 |
WLAN Antenna....................................................................................................... |
21 |
LCD Latch .............................................................................................................. |
21 |
Notice ..................................................................................................................... |
22 |
3
Overview
This document contains step-by-step disassembly instructions for the EasyNote V / MV chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled.
Packard Bell reserves the right to make changes to the chassis without notice.
Disassembly Instructions
When disassembling the system unit, follow these general rules:
Turn off the power.
Disconnect the AC adapter.
Remove the battery.
Do not disassemble the system into parts that are smaller than those specified in the instructions.
Label all removed connectors; note where the connector goes and in what position it was installed.
Reassembly Instructions
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the chassis. Check that everything is properly installed and tightened.
Required Tools
All disassembly procedures can be performed using the following tools:
Philips (#2 bit) screwdriver
4
Hazardous Voltage
There is hazardous voltage present inside the computer when it is connected to an AC supply, even when the computer’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authorized Service Provider for proper (un)installation of optional hardware devices.
Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards and integrated circuits (ICs). To reduce risk of damage, store them in protective packaging whenever they are not installed in your system.
Add-in cards can be extremely sensitive to ESD and always require careful handling. After removing the card from the computer, place the card flat on a grounded, static-free surface, component-side up. Use a conductive foam pad if available, but not the card wrapper. Do not slide the card over any surface.
Before you install or remove memory modules, video memory, disk drives, circuit cards or other devices, protect them from static electricity. To do so, make sure your computer’s power switch is OFF. Then, unplug the computer’s AC power cord. Before picking up the device you (un)install, you should wear an antistatic wrist wrap (available at electronic supply stores). Be sure to connect the wrist wrap to an unpainted metal portion of the computer chassis. As an alternative, you can dissipate electrostatic build-up by touching an unpainted metal portion of the computer chassis with one hand. Then touch the device you are (un)installing with the other hand, and maintain continuous contact with it until it is (un)installed in the computer.
Power Supply Unit
Under no circumstances should you attempt to disassemble the power supply. The power supply contains no user-serviceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury. Always return a defective power supply to your dealer.
WARNING
Ensure that the computer is disconnected from its power source and from all telecommunications links, networks, or modem lines whenever the chassis cover is removed. Do not operate the computer with the cover removed.
AVERTISSEMENT
Assurez-vous que le système est débranché de son alimentation ainsi que de toutes les liaisons de télécommunication, des réseaux, et des lignes de modem avant d’enlever le capot. Ne pas utiliser le système quand le capot est enlevé.
WARNUNG
Das System darf weder an eine Stromquelle angeschlossen sein noch eine Verbindung mit einer Telekommunikationseinrichtung, einem Netzwerk oder einer Modem-Leitung haben, wenn die Gehäuseabdeckung entfernt wird. Nehmen Sie das System nicht ohne die Abdeckung in Betrieb.
ADVERTENCIA
Asegúrese de que cada vez que se quite la cubierta del chasis, el sistema haya sido desconectado de la red de alimentación y de todos lo enlaces de telecomunicaciones, de red y de líneas de módem. No ponga en funcionamiento el sistema mientras la cubierta esté quitada.
WAARSCHUWING
Zorg er voor dat alle verbindingen van en naar de computer (stroom, modem, netwerk, etc) verbroken worden voordat de behuizing geopend wordt. Zet de computer nooit aan als de behuizing geopend is.
AVVERTENZA
Prima di rimuovere il coperchio del telaio, assicurarsi che il sistema sia scollegato dall’alimentazione, da tutti i collegamenti di comunicazione, reti o linee di modem. Non avviare il sistema senza aver prima messo a posto il coperchio.
5
Base Assembly
Battery
1. Slide aside the two latches and slide out the battery.
Hard Disk Drive
1.Remove the battery as described in chapter Battery.
2.Remove the 2 screws and lift the HDD cover.
6
3. Pull the hard disk bracket leftwards.
4.Lift out the hard disk.
5.The hard disk is mounted inside the bracket.
6.To remove the bracket, remove the 4 screws (2 on each side).
Optical Disc Drive
1.Remove the battery as described in chapter Battery.
2.Remove the two screws indicated below.
3. Pull out the optical disk drive.
7
Memory Modules
1.Remove the battery as described in chapter Battery.
2.Remove the 4 screws of the CPU cover.
-Note: The CPU cover on the EasyNote MV35, MV51 and MV61 is secured with 7 screws.
3. The memory modules can be found under a flap of EMI protection material.
- Note: The EasyNote MV35, MV51 and MV61 do not have the EMI shielding material. The location of the SO-DIMM modules is identical, however.
4. Lift the flap to access the SO-DIMM slots.
Loading...