H RESTRAINTS
SECTION SB
SEAT BELTS
CONTENTS
A
B
C
D
E
PRECAUTIONS ......................................................... |
2 |
Precautions for Supplemental Restraint System |
|
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- |
|
SIONER” ................................................................. |
2 |
Precautions for Seat Belt Service ........................... |
2 |
AFTER A COLLISION .......................................... |
2 |
SEAT BELTS ............................................................. |
3 |
System Description ................................................. |
3 |
SEAT BELT WARNING LAMP ............................. |
3 |
Removal and Installation of Front Seat Belt ............ |
3 |
REMOVAL OF SEAT BELT RETRACTOR ........... |
3 |
INSTALLATION OF SEAT BELT RETRACTOR..... |
3 |
REMOVAL OF SEAT BELT BUCKLE ................... |
4 |
INSTALLATION OF SEAT BELT BUCKLE ........... |
4 |
Removal and Installation of Rear Seat Belt ............ |
4 |
REMOVAL OF LH/RH SEAT BELT ...................... |
4 |
INSTALLATION OF LH/RH SEAT BELT ............... |
4 |
REMOVAL OF CENTER SEAT BELT .................. |
5 |
INSTALLATION OF CENTER SEAT BELT ........... |
5 |
Seat Belt Inspection ................................................. |
6 |
AFTER A COLLISION .......................................... |
6 |
PRELIMINARY CHECKS ..................................... |
6 |
SEAT BELT RETRACTOR ON-VEHICLE |
|
CHECK ................................................................. |
7 |
SEAT BELT RETRACTOR OFF-VEHICLE |
|
CHECK ................................................................. |
8 |
TOP TETHER STRAP CHILD RESTRAINT ............... |
9 |
Removal and Installation ......................................... |
9 |
REMOVAL ............................................................ |
9 |
INSTALLATION .................................................... |
9 |
F
G
SB
I
J
K
L
M
Revision: 2006 July |
SB-1 |
2006 X-Trail |
|
PRECAUTIONS |
|
|
PRECAUTIONS |
PFP:00001 |
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the SRS and SB section of this Service Manual.
WARNING:
●To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
●Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section.
●Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
Precautions for Seat Belt Service |
AHS000RE |
CAUTION:
●Before removing the seat belt pre-tensioner assembly, turn the ignition switch off, disconnect the both battery cables and wait at least 3 minutes.
●Do not use electrical test equipment for seat belt pre-tensioner connector.
●After replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting front seat belt pre-tensioner connector, check the system function. Refer to SRS-13, "SRS Operation Check" .
●Do not use disassembled buckle or seat belt assembly.
●Replace anchor bolts if they are deformed or worn out.
●Never oil tongue and buckle.
●If any component of seat belt assembly is questionable, do not repair. Replace the whole seat belt assembly.
●If webbing is cut, frayed, or damaged, replace seat belt assembly.
●When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.
WARNING:
Inspect all seat belt assemblies including retractors and attaching hardware after any collision. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly. Failure to do so could result in serious personal injury in an accident. Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed.
Replace any seat belt assembly (including anchor bolts) if:
●The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and buckles show no damage and continue to operate properly).
●The seat belt was damaged in an accident. (i.e. torn webbing, bent retractor or guide).
●The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly.
●Anchor bolts are deformed or worn out.
●The seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed.
Revision: 2006 July |
SB-2 |
2006 X-Trail |
|
SEAT BELTS |
|
|
SEAT BELTS |
PFP:86884 |
System Description |
AHS000RF |
SEAT BELT WARNING LAMP |
|
●Fasten driver's seat belt.
●The seat belt warning lamp should go out.
●If the seat belt warning lamp does not go out. Refer to DI-25, "Wiring Diagram — WARN — " .
Removal and Installation of Front Seat Belt |
AHS000RG |
SHIA0243E
CAUTION:
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least 3 minutes.
1. |
Remove adjust cover. |
|
2. |
Remove shoulder anchor bolt. |
|
3. |
Slide the floor anchor cover. |
|
4. |
Remove floor anchor bolt. |
|
5. |
Remove center pillar upper and lower garnish. Refer to EI-36, "Removal and Installation" . |
|
6. |
Disconnect the seat belt pre-tensioner connector. |
|
|
||
|
CAUTION: |
|
|
● For connecting/disconnecting seat belt pre-tensioner |
|
|
connector, insert thin screwdriver wrapped in tape into |
|
|
notch, lift lock and disconnect connector. |
|
|
● Connect connector with lock raised, and push lock into |
|
|
connector. |
PHIA0341E
7.Remove seat belt pre-tensioner retractor fixing screws to remove seat belt assembly.
CAUTION:
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least 3 minutes.
Install in the reverse order of removal.
A
B
C
D
E
F
G
SB
I
J
K
L
M
Revision: 2006 July |
SB-3 |
2006 X-Trail |