Hobart D-300 User Manual

D300 MIXER

D300 MIXERS

ML - 104421, 104423

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

FORM 18816 Rev. A (Feb. 2000)

Model D300 Mixer

– 2 –

2345678901234567890123456789012123456789

The D300 Mixer (30 quart) features a 3/4 horsepower motor, a timer, and a #12 attachment hub as standard equipment. The standard 30 quart mixer bowl can be equipped with a variety of agitators. A 20 quart bowl, bowl adapter, and agitators are available options on the D300.

Bowl Guard is standard equipment on all D300 models.

23456789012345678901234567890121234567890123456789012345678901212345678901

Installation, Operation, and Care of

MODEL D300 MIXERS

SAVE THESE INSTRUCTIONS

GENERAL

Programmable Timer Controller is optional on D300 models.

These mixers can be ordered with deluxe finish, which includes a chrome plated transmission case, base, bowl support, and pedestal.

A variety of attachments and accessories are available for all mixers. These are described in a separate

Use and Applications Handbook

which is furnished with each mixer.

INSTALLATION

UNPACKING

Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.

Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate.

LOCATION

Place the mixer in its operating location. There should be adequate space around the mixer for the user to operate the controls and install and remove bowls.

A Deck Plate Kit is available from Hobart and holes are provided in the base for permanent bolting to the floor, although this is not necessary in normal installations. Four plastic plugs are supplied with the mixer to plug these holes if they are not used.

– 3 –

ELECTRICAL CONNECTION

WARNING: ELECTRICAL AND GROUNDING CONNECTION MUST COMPLY WITH THE

APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.

WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.

ELECTRICAL DATA

Models Volts / Hz / Ph Rated Amps

D300 115 / 60 / 1 10.2 15 15 14 20 20 12

D300 200 / 60 / 1 5.6 15 6 14 15 10 14

D300 230 / 60 / 1 5.1 15 6 14 15 10 14

D300 200 / 60 / 3 2.1 15 3 14 15 3 14

D300 230 / 60 / 3 2.0 15 3 14 15 3 14

D300 460 / 60 / 3 1.0 15 1 14 15 1 14

Circuit Size (Minimum) & Fuse / Circuit Breaker Size (Maximum) compiled in accordance with the National Electrical Code (ANSI/NFPA 70), 1993 Edition.

Circuit Size

(Amps)

* Dual Element

Fuse Size *

(Amps)

Time-Delay Fuse

60°C Copper

Wire Size

Circuit Size

(Amps)

** Inverse Time

Circuit Breaker **

(Amps)

Circuit Breaker

60°C Copper

Wire Size

A hole for 3⁄4" trade size conduit is located at the bottom of the pedestal (Fig. 1). Make electrical connections to the pigtail leads per the wiring diagram supplied with the mixer.

Fig. 1

Check Rotation (Three-Phase Machines Only)

Three-phase machines must be connected so the planetary rotates in the direction of the arrow on the Drip Cup. To check rotation:

Set the gear shift lever on 1.

Apply power to the mixer, set the Electro-Mechanical Timer on HOLD; or, if equipped with a Programmable Timer Controller, set it on [ -- : -- ]. With the Bowl Support all the way up, momentarily run the machine by pushing the START and then STOP buttons.

If rotation is incorrect, DISCONNECT ELECTRICAL POWER SUPPLY and interchange any two of the incoming power supply leads.

– 4 –

+ 8 hidden pages